Merge git://git.infradead.org/mtd-2.6

* git://git.infradead.org/mtd-2.6: (82 commits)
  [MTD] m25p80: Add Support for ATMEL AT25DF641 64-Megabit SPI Flash
  [MTD] m25p80: add FAST_READ access support to M25Pxx
  [MTD] [NAND] bf5xx_nand: Avoid crash if bfin_mac is installed.
  [MTD] [NAND] at91_nand: control NCE signal
  [MTD] [NAND] AT91 hardware ECC compile fix for at91sam9263 / at91sam9260
  [MTD] [NAND] Hardware ECC controller on at91sam9263 / at91sam9260
  [JFFS2] Introduce dbg_readinode2 log level, use it to shut read_dnode() up
  [JFFS2] Fix jffs2_reserve_space() when all blocks are pending erasure.
  [JFFS2] Add erase_checking_list to hold blocks being marked.
  UBI: add a message
  [JFFS2] Return values of jffs2_block_check_erase error paths
  [MTD] Clean up AR7 partition map support
  [MTD] [NOR] Fix Intel CFI driver for collie flash
  [JFFS2] Finally remove redundant ref->__totlen field.
  [JFFS2] Honour TEST_TOTLEN macro in debugging code. ref->__totlen is going!
  [JFFS2] Add paranoia debugging for superblock counts
  [JFFS2] Fix free space leak with in-band cleanmarkers
  [JFFS2] Self-sufficient #includes in jffs2_fs_i.h: include <linux/mutex.h>
  [MTD] [NAND] Verify probe by retrying to checking the results match
  [MTD] [NAND] S3C2410 Allow ECC disable to be specified by the board
  ...

1 files changed, 56 insertions, 0 deletions

diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index 959fb86cda01..5076faf9ca66 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -278,6 +278,54 @@ config MTD_NAND_AT91
 	help
 	  Enables support for NAND Flash / Smart Media Card interface
 	  on Atmel AT91 processors.
+choice
+	prompt "ECC management for NAND Flash / SmartMedia on AT91"
+	depends on MTD_NAND_AT91
+
+config MTD_NAND_AT91_ECC_HW
+	bool "Hardware ECC"
+	depends on ARCH_AT91SAM9263 || ARCH_AT91SAM9260
+	help
+	  Uses hardware ECC provided by the at91sam9260/at91sam9263 chip
+	  instead of software ECC.
+	  The hardware ECC controller is capable of single bit error
+	  correction and 2-bit random detection per page.
+
+	  NB : hardware and software ECC schemes are incompatible.
+	  If you switch from one to another, you'll have to erase your
+	  mtd partition.
+
+	  If unsure, say Y
+
+config MTD_NAND_AT91_ECC_SOFT
+	bool "Software ECC"
+	help
+	  Uses software ECC.
+
+	  NB : hardware and software ECC schemes are incompatible.
+	  If you switch from one to another, you'll have to erase your
+	  mtd partition.
+
+config MTD_NAND_AT91_ECC_NONE
+	bool "No ECC (testing only, DANGEROUS)"
+	depends on DEBUG_KERNEL
+	help
+	  No ECC will be used.
+	  It's not a good idea and it should be reserved for testing
+	  purpose only.
+
+	  If unsure, say N
+
+	  endchoice
+
+endchoice
+
+config MTD_NAND_PXA3xx
+	bool "Support for NAND flash devices on PXA3xx"
+	depends on MTD_NAND && PXA3xx
+	help
+	  This enables the driver for the NAND flash device found on
+	  PXA3xx processors
 
 config MTD_NAND_CM_X270
 	tristate "Support for NAND Flash on CM-X270 modules"
@@ -330,4 +378,12 @@ config MTD_NAND_FSL_ELBC
 	  Enabling this option will enable you to use this to control
 	  external NAND devices.
 
+config MTD_NAND_FSL_UPM
+	tristate "Support for NAND on Freescale UPM"
+	depends on MTD_NAND && OF_GPIO && (PPC_83xx || PPC_85xx)
+	select FSL_LBC
+	help
+	  Enables support for NAND Flash chips wired onto Freescale PowerPC
+	  processor localbus with User-Programmable Machine support.
+
 endif # MTD_NAND