mtd: doc: remove support for DoC 2000/2001/2001+

These drivers are deprecated for very long time, and we have a different driver
for these called "diskonchip". Thus, kill the ancient cruft.

Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

7 files changed, 0 insertions, 3996 deletions

diff --git a/drivers/mtd/devices/Kconfig b/drivers/mtd/devices/Kconfig
index 12311f506ca1..ec4a2cc3e9b5 100644
--- a/drivers/mtd/devices/Kconfig
+++ b/drivers/mtd/devices/Kconfig
@@ -205,69 +205,6 @@ config MTD_BLOCK2MTD
 
 comment "Disk-On-Chip Device Drivers"
 
-config MTD_DOC2000
-	tristate "M-Systems Disk-On-Chip 2000 and Millennium (DEPRECATED)"
-	depends on MTD_NAND
-	select MTD_DOCPROBE
-	select MTD_NAND_IDS
-	---help---
-	  This provides an MTD device driver for the M-Systems DiskOnChip
-	  2000 and Millennium devices.  Originally designed for the DiskOnChip
-	  2000, it also now includes support for the DiskOnChip Millennium.
-	  If you have problems with this driver and the DiskOnChip Millennium,
-	  you may wish to try the alternative Millennium driver below. To use
-	  the alternative driver, you will need to undefine DOC_SINGLE_DRIVER
-	  in the <file:drivers/mtd/devices/docprobe.c> source code.
-
-	  If you use this device, you probably also want to enable the NFTL
-	  'NAND Flash Translation Layer' option below, which is used to
-	  emulate a block device by using a kind of file system on the flash
-	  chips.
-
-	  NOTE: This driver is deprecated and will probably be removed soon.
-	  Please try the new DiskOnChip driver under "NAND Flash Device
-	  Drivers".
-
-config MTD_DOC2001
-	tristate "M-Systems Disk-On-Chip Millennium-only alternative driver (DEPRECATED)"
-	depends on MTD_NAND
-	select MTD_DOCPROBE
-	select MTD_NAND_IDS
-	---help---
-	  This provides an alternative MTD device driver for the M-Systems
-	  DiskOnChip Millennium devices.  Use this if you have problems with
-	  the combined DiskOnChip 2000 and Millennium driver above.  To get
-	  the DiskOnChip probe code to load and use this driver instead of
-	  the other one, you will need to undefine DOC_SINGLE_DRIVER near
-	  the beginning of <file:drivers/mtd/devices/docprobe.c>.
-
-	  If you use this device, you probably also want to enable the NFTL
-	  'NAND Flash Translation Layer' option below, which is used to
-	  emulate a block device by using a kind of file system on the flash
-	  chips.
-
-	  NOTE: This driver is deprecated and will probably be removed soon.
-	  Please try the new DiskOnChip driver under "NAND Flash Device
-	  Drivers".
-
-config MTD_DOC2001PLUS
-	tristate "M-Systems Disk-On-Chip Millennium Plus"
-	depends on MTD_NAND
-	select MTD_DOCPROBE
-	select MTD_NAND_IDS
-	---help---
-	  This provides an MTD device driver for the M-Systems DiskOnChip
-	  Millennium Plus devices.
-
-	  If you use this device, you probably also want to enable the INFTL
-	  'Inverse NAND Flash Translation Layer' option below, which is used
-	  to emulate a block device by using a kind of file system on the
-	  flash chips.
-
-	  NOTE: This driver will soon be replaced by the new DiskOnChip driver
-	  under "NAND Flash Device Drivers" (currently that driver does not
-	  support all Millennium Plus devices).
-
 config MTD_DOCG3
 	tristate "M-Systems Disk-On-Chip G3"
 	select BCH
diff --git a/drivers/mtd/devices/Makefile b/drivers/mtd/devices/Makefile
index 369a1943ca25..d83bd73096f6 100644
--- a/drivers/mtd/devices/Makefile
+++ b/drivers/mtd/devices/Makefile
@@ -2,12 +2,7 @@
 # linux/drivers/mtd/devices/Makefile
 #
 
-obj-$(CONFIG_MTD_DOC2000)	+= doc2000.o
-obj-$(CONFIG_MTD_DOC2001)	+= doc2001.o
-obj-$(CONFIG_MTD_DOC2001PLUS)	+= doc2001plus.o
 obj-$(CONFIG_MTD_DOCG3)		+= docg3.o
-obj-$(CONFIG_MTD_DOCPROBE)	+= docprobe.o
-obj-$(CONFIG_MTD_DOCECC)	+= docecc.o
 obj-$(CONFIG_MTD_SLRAM)		+= slram.o
 obj-$(CONFIG_MTD_PHRAM)		+= phram.o
 obj-$(CONFIG_MTD_PMC551)	+= pmc551.o
diff --git a/drivers/mtd/devices/doc2000.c b/drivers/mtd/devices/doc2000.c
deleted file mode 100644
index 363ec3c55d92..000000000000
--- a/drivers/mtd/devices/doc2000.c
+++ /dev/null
@@ -1,1178 +0,0 @@
-
-/*
- * Linux driver for Disk-On-Chip 2000 and Millennium
- * (c) 1999 Machine Vision Holdings, Inc.
- * (c) 1999, 2000 David Woodhouse <dwmw2@infradead.org>
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <asm/errno.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
-#include <linux/delay.h>
-#include <linux/slab.h>
-#include <linux/sched.h>
-#include <linux/init.h>
-#include <linux/types.h>
-#include <linux/bitops.h>
-#include <linux/mutex.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/nand.h>
-#include <linux/mtd/doc2000.h>
-
-#define DOC_SUPPORT_2000
-#define DOC_SUPPORT_2000TSOP
-#define DOC_SUPPORT_MILLENNIUM
-
-#ifdef DOC_SUPPORT_2000
-#define DoC_is_2000(doc) (doc->ChipID == DOC_ChipID_Doc2k)
-#else
-#define DoC_is_2000(doc) (0)
-#endif
-
-#if defined(DOC_SUPPORT_2000TSOP) || defined(DOC_SUPPORT_MILLENNIUM)
-#define DoC_is_Millennium(doc) (doc->ChipID == DOC_ChipID_DocMil)
-#else
-#define DoC_is_Millennium(doc) (0)
-#endif
-
-/* #define ECC_DEBUG */
-
-/* I have no idea why some DoC chips can not use memcpy_from|to_io().
- * This may be due to the different revisions of the ASIC controller built-in or
- * simplily a QA/Bug issue. Who knows ?? If you have trouble, please uncomment
- * this:
- #undef USE_MEMCPY
-*/
-
-static int doc_read(struct mtd_info *mtd, loff_t from, size_t len,
-		    size_t *retlen, u_char *buf);
-static int doc_write(struct mtd_info *mtd, loff_t to, size_t len,
-		     size_t *retlen, const u_char *buf);
-static int doc_read_oob(struct mtd_info *mtd, loff_t ofs,
-			struct mtd_oob_ops *ops);
-static int doc_write_oob(struct mtd_info *mtd, loff_t ofs,
-			 struct mtd_oob_ops *ops);
-static int doc_write_oob_nolock(struct mtd_info *mtd, loff_t ofs, size_t len,
-			 size_t *retlen, const u_char *buf);
-static int doc_erase (struct mtd_info *mtd, struct erase_info *instr);
-
-static struct mtd_info *doc2klist = NULL;
-
-/* Perform the required delay cycles by reading from the appropriate register */
-static void DoC_Delay(struct DiskOnChip *doc, unsigned short cycles)
-{
-	volatile char dummy;
-	int i;
-
-	for (i = 0; i < cycles; i++) {
-		if (DoC_is_Millennium(doc))
-			dummy = ReadDOC(doc->virtadr, NOP);
-		else
-			dummy = ReadDOC(doc->virtadr, DOCStatus);
-	}
-
-}
-
-/* DOC_WaitReady: Wait for RDY line to be asserted by the flash chip */
-static int _DoC_WaitReady(struct DiskOnChip *doc)
-{
-	void __iomem *docptr = doc->virtadr;
-	unsigned long timeo = jiffies + (HZ * 10);
-
-	pr_debug("_DoC_WaitReady called for out-of-line wait\n");
-
-	/* Out-of-line routine to wait for chip response */
-	while (!(ReadDOC(docptr, CDSNControl) & CDSN_CTRL_FR_B)) {
-		/* issue 2 read from NOP register after reading from CDSNControl register
-	   	see Software Requirement 11.4 item 2. */
-		DoC_Delay(doc, 2);
-
-		if (time_after(jiffies, timeo)) {
-			pr_debug("_DoC_WaitReady timed out.\n");
-			return -EIO;
-		}
-		udelay(1);
-		cond_resched();
-	}
-
-	return 0;
-}
-
-static inline int DoC_WaitReady(struct DiskOnChip *doc)
-{
-	void __iomem *docptr = doc->virtadr;
-
-	/* This is inline, to optimise the common case, where it's ready instantly */
-	int ret = 0;
-
-	/* 4 read form NOP register should be issued in prior to the read from CDSNControl
-	   see Software Requirement 11.4 item 2. */
-	DoC_Delay(doc, 4);
-
-	if (!(ReadDOC(docptr, CDSNControl) & CDSN_CTRL_FR_B))
-		/* Call the out-of-line routine to wait */
-		ret = _DoC_WaitReady(doc);
-
-	/* issue 2 read from NOP register after reading from CDSNControl register
-	   see Software Requirement 11.4 item 2. */
-	DoC_Delay(doc, 2);
-
-	return ret;
-}
-
-/* DoC_Command: Send a flash command to the flash chip through the CDSN Slow IO register to
-   bypass the internal pipeline. Each of 4 delay cycles (read from the NOP register) is
-   required after writing to CDSN Control register, see Software Requirement 11.4 item 3. */
-
-static int DoC_Command(struct DiskOnChip *doc, unsigned char command,
-			      unsigned char xtraflags)
-{
-	void __iomem *docptr = doc->virtadr;
-
-	if (DoC_is_2000(doc))
-		xtraflags |= CDSN_CTRL_FLASH_IO;
-
-	/* Assert the CLE (Command Latch Enable) line to the flash chip */
-	WriteDOC(xtraflags | CDSN_CTRL_CLE | CDSN_CTRL_CE, docptr, CDSNControl);
-	DoC_Delay(doc, 4);	/* Software requirement 11.4.3 for Millennium */
-
-	if (DoC_is_Millennium(doc))
-		WriteDOC(command, docptr, CDSNSlowIO);
-
-	/* Send the command */
-	WriteDOC_(command, docptr, doc->ioreg);
-	if (DoC_is_Millennium(doc))
-		WriteDOC(command, docptr, WritePipeTerm);
-
-	/* Lower the CLE line */
-	WriteDOC(xtraflags | CDSN_CTRL_CE, docptr, CDSNControl);
-	DoC_Delay(doc, 4);	/* Software requirement 11.4.3 for Millennium */
-
-	/* Wait for the chip to respond - Software requirement 11.4.1 (extended for any command) */
-	return DoC_WaitReady(doc);
-}
-
-/* DoC_Address: Set the current address for the flash chip through the CDSN Slow IO register to
-   bypass the internal pipeline. Each of 4 delay cycles (read from the NOP register) is
-   required after writing to CDSN Control register, see Software Requirement 11.4 item 3. */
-
-static int DoC_Address(struct DiskOnChip *doc, int numbytes, unsigned long ofs,
-		       unsigned char xtraflags1, unsigned char xtraflags2)
-{
-	int i;
-	void __iomem *docptr = doc->virtadr;
-
-	if (DoC_is_2000(doc))
-		xtraflags1 |= CDSN_CTRL_FLASH_IO;
-
-	/* Assert the ALE (Address Latch Enable) line to the flash chip */
-	WriteDOC(xtraflags1 | CDSN_CTRL_ALE | CDSN_CTRL_CE, docptr, CDSNControl);
-
-	DoC_Delay(doc, 4);	/* Software requirement 11.4.3 for Millennium */
-
-	/* Send the address */
-	/* Devices with 256-byte page are addressed as:
-	   Column (bits 0-7), Page (bits 8-15, 16-23, 24-31)
-	   * there is no device on the market with page256
-	   and more than 24 bits.
-	   Devices with 512-byte page are addressed as:
-	   Column (bits 0-7), Page (bits 9-16, 17-24, 25-31)
-	   * 25-31 is sent only if the chip support it.
-	   * bit 8 changes the read command to be sent
-	   (NAND_CMD_READ0 or NAND_CMD_READ1).
-	 */
-
-	if (numbytes == ADDR_COLUMN || numbytes == ADDR_COLUMN_PAGE) {
-		if (DoC_is_Millennium(doc))
-			WriteDOC(ofs & 0xff, docptr, CDSNSlowIO);
-		WriteDOC_(ofs & 0xff, docptr, doc->ioreg);
-	}
-
-	if (doc->page256) {
-		ofs = ofs >> 8;
-	} else {
-		ofs = ofs >> 9;
-	}
-
-	if (numbytes == ADDR_PAGE || numbytes == ADDR_COLUMN_PAGE) {
-		for (i = 0; i < doc->pageadrlen; i++, ofs = ofs >> 8) {
-			if (DoC_is_Millennium(doc))
-				WriteDOC(ofs & 0xff, docptr, CDSNSlowIO);
-			WriteDOC_(ofs & 0xff, docptr, doc->ioreg);
-		}
-	}
-
-	if (DoC_is_Millennium(doc))
-		WriteDOC(ofs & 0xff, docptr, WritePipeTerm);
-
-	DoC_Delay(doc, 2);	/* Needed for some slow flash chips. mf. */
-
-	/* FIXME: The SlowIO's for millennium could be replaced by
-	   a single WritePipeTerm here. mf. */
-
-	/* Lower the ALE line */
-	WriteDOC(xtraflags1 | xtraflags2 | CDSN_CTRL_CE, docptr,
-		 CDSNControl);
-
-	DoC_Delay(doc, 4);	/* Software requirement 11.4.3 for Millennium */
-
-	/* Wait for the chip to respond - Software requirement 11.4.1 */
-	return DoC_WaitReady(doc);
-}
-
-/* Read a buffer from DoC, taking care of Millennium odditys */
-static void DoC_ReadBuf(struct DiskOnChip *doc, u_char * buf, int len)
-{
-	volatile int dummy;
-	int modulus = 0xffff;
-	void __iomem *docptr = doc->virtadr;
-	int i;
-
-	if (len <= 0)
-		return;
-
-	if (DoC_is_Millennium(doc)) {
-		/* Read the data via the internal pipeline through CDSN IO register,
-		   see Pipelined Read Operations 11.3 */
-		dummy = ReadDOC(docptr, ReadPipeInit);
-
-		/* Millennium should use the LastDataRead register - Pipeline Reads */
-		len--;
-
-		/* This is needed for correctly ECC calculation */
-		modulus = 0xff;
-	}
-
-	for (i = 0; i < len; i++)
-		buf[i] = ReadDOC_(docptr, doc->ioreg + (i & modulus));
-
-	if (DoC_is_Millennium(doc)) {
-		buf[i] = ReadDOC(docptr, LastDataRead);
-	}
-}
-
-/* Write a buffer to DoC, taking care of Millennium odditys */
-static void DoC_WriteBuf(struct DiskOnChip *doc, const u_char * buf, int len)
-{
-	void __iomem *docptr = doc->virtadr;
-	int i;
-
-	if (len <= 0)
-		return;
-
-	for (i = 0; i < len; i++)
-		WriteDOC_(buf[i], docptr, doc->ioreg + i);
-
-	if (DoC_is_Millennium(doc)) {
-		WriteDOC(0x00, docptr, WritePipeTerm);
-	}
-}
-
-
-/* DoC_SelectChip: Select a given flash chip within the current floor */
-
-static inline int DoC_SelectChip(struct DiskOnChip *doc, int chip)
-{
-	void __iomem *docptr = doc->virtadr;
-
-	/* Software requirement 11.4.4 before writing DeviceSelect */
-	/* Deassert the CE line to eliminate glitches on the FCE# outputs */
-	WriteDOC(CDSN_CTRL_WP, docptr, CDSNControl);
-	DoC_Delay(doc, 4);	/* Software requirement 11.4.3 for Millennium */
-
-	/* Select the individual flash chip requested */
-	WriteDOC(chip, docptr, CDSNDeviceSelect);
-	DoC_Delay(doc, 4);
-
-	/* Reassert the CE line */
-	WriteDOC(CDSN_CTRL_CE | CDSN_CTRL_FLASH_IO | CDSN_CTRL_WP, docptr,
-		 CDSNControl);
-	DoC_Delay(doc, 4);	/* Software requirement 11.4.3 for Millennium */
-
-	/* Wait for it to be ready */
-	return DoC_WaitReady(doc);
-}
-
-/* DoC_SelectFloor: Select a given floor (bank of flash chips) */
-
-static inline int DoC_SelectFloor(struct DiskOnChip *doc, int floor)
-{
-	void __iomem *docptr = doc->virtadr;
-
-	/* Select the floor (bank) of chips required */
-	WriteDOC(floor, docptr, FloorSelect);
-
-	/* Wait for the chip to be ready */
-	return DoC_WaitReady(doc);
-}
-
-/* DoC_IdentChip: Identify a given NAND chip given {floor,chip} */
-
-static int DoC_IdentChip(struct DiskOnChip *doc, int floor, int chip)
-{
-	int mfr, id, i, j;
-	volatile char dummy;
-
-	/* Page in the required floor/chip */
-	DoC_SelectFloor(doc, floor);
-	DoC_SelectChip(doc, chip);
-
-	/* Reset the chip */
-	if (DoC_Command(doc, NAND_CMD_RESET, CDSN_CTRL_WP)) {
-		pr_debug("DoC_Command (reset) for %d,%d returned true\n",
-		      floor, chip);
-		return 0;
-	}
-
-
-	/* Read the NAND chip ID: 1. Send ReadID command */
-	if (DoC_Command(doc, NAND_CMD_READID, CDSN_CTRL_WP)) {
-		pr_debug("DoC_Command (ReadID) for %d,%d returned true\n",
-		      floor, chip);
-		return 0;
-	}
-
-	/* Read the NAND chip ID: 2. Send address byte zero */
-	DoC_Address(doc, ADDR_COLUMN, 0, CDSN_CTRL_WP, 0);
-
-	/* Read the manufacturer and device id codes from the device */
-
-	if (DoC_is_Millennium(doc)) {
-		DoC_Delay(doc, 2);
-		dummy = ReadDOC(doc->virtadr, ReadPipeInit);
-		mfr = ReadDOC(doc->virtadr, LastDataRead);
-
-		DoC_Delay(doc, 2);
-		dummy = ReadDOC(doc->virtadr, ReadPipeInit);
-		id = ReadDOC(doc->virtadr, LastDataRead);
-	} else {
-		/* CDSN Slow IO register see Software Req 11.4 item 5. */
-		dummy = ReadDOC(doc->virtadr, CDSNSlowIO);
-		DoC_Delay(doc, 2);
-		mfr = ReadDOC_(doc->virtadr, doc->ioreg);
-
-		/* CDSN Slow IO register see Software Req 11.4 item 5. */
-		dummy = ReadDOC(doc->virtadr, CDSNSlowIO);
-		DoC_Delay(doc, 2);
-		id = ReadDOC_(doc->virtadr, doc->ioreg);
-	}
-
-	/* No response - return failure */
-	if (mfr == 0xff || mfr == 0)
-		return 0;
-
-	/* Check it's the same as the first chip we identified.
-	 * M-Systems say that any given DiskOnChip device should only
-	 * contain _one_ type of flash part, although that's not a
-	 * hardware restriction. */
-	if (doc->mfr) {
-		if (doc->mfr == mfr && doc->id == id)
-			return 1;	/* This is the same as the first */
-		else
-			printk(KERN_WARNING
-			       "Flash chip at floor %d, chip %d is different:\n",
-			       floor, chip);
-	}
-
-	/* Print and store the manufacturer and ID codes. */
-	for (i = 0; nand_flash_ids[i].name != NULL; i++) {
-		if (id == nand_flash_ids[i].dev_id) {
-			/* Try to identify manufacturer */
-			for (j = 0; nand_manuf_ids[j].id != 0x0; j++) {
-				if (nand_manuf_ids[j].id == mfr)
-					break;
-			}
-			printk(KERN_INFO
-			       "Flash chip found: Manufacturer ID: %2.2X, "
-			       "Chip ID: %2.2X (%s:%s)\n", mfr, id,
-			       nand_manuf_ids[j].name, nand_flash_ids[i].name);
-			if (!doc->mfr) {
-				doc->mfr = mfr;
-				doc->id = id;
-				doc->chipshift =
-					ffs((nand_flash_ids[i].chipsize << 20)) - 1;
-				doc->page256 = (nand_flash_ids[i].pagesize == 256) ? 1 : 0;
-				doc->pageadrlen = doc->chipshift > 25 ? 3 : 2;
-				doc->erasesize =
-				    nand_flash_ids[i].erasesize;
-				return 1;
-			}
-			return 0;
-		}
-	}
-
-
-	/* We haven't fully identified the chip. Print as much as we know. */
-	printk(KERN_WARNING "Unknown flash chip found: %2.2X %2.2X\n",
-	       id, mfr);
-
-	printk(KERN_WARNING "Please report to dwmw2@infradead.org\n");
-	return 0;
-}
-
-/* DoC_ScanChips: Find all NAND chips present in a DiskOnChip, and identify them */
-
-static void DoC_ScanChips(struct DiskOnChip *this, int maxchips)
-{
-	int floor, chip;
-	int numchips[MAX_FLOORS];
-	int ret = 1;
-
-	this->numchips = 0;
-	this->mfr = 0;
-	this->id = 0;
-
-	/* For each floor, find the number of valid chips it contains */
-	for (floor = 0; floor < MAX_FLOORS; floor++) {
-		ret = 1;
-		numchips[floor] = 0;
-		for (chip = 0; chip < maxchips && ret != 0; chip++) {
-
-			ret = DoC_IdentChip(this, floor, chip);
-			if (ret) {
-				numchips[floor]++;
-				this->numchips++;
-			}
-		}
-	}
-
-	/* If there are none at all that we recognise, bail */
-	if (!this->numchips) {
-		printk(KERN_NOTICE "No flash chips recognised.\n");
-		return;
-	}
-
-	/* Allocate an array to hold the information for each chip */
-	this->chips = kmalloc(sizeof(struct Nand) * this->numchips, GFP_KERNEL);
-	if (!this->chips) {
-		printk(KERN_NOTICE "No memory for allocating chip info structures\n");
-		return;
-	}
-
-	ret = 0;
-
-	/* Fill out the chip array with {floor, chipno} for each
-	 * detected chip in the device. */
-	for (floor = 0; floor < MAX_FLOORS; floor++) {
-		for (chip = 0; chip < numchips[floor]; chip++) {
-			this->chips[ret].floor = floor;
-			this->chips[ret].chip = chip;
-			this->chips[ret].curadr = 0;
-			this->chips[ret].curmode = 0x50;
-			ret++;
-		}
-	}
-
-	/* Calculate and print the total size of the device */
-	this->totlen = this->numchips * (1 << this->chipshift);
-
-	printk(KERN_INFO "%d flash chips found. Total DiskOnChip size: %ld MiB\n",
-	       this->numchips, this->totlen >> 20);
-}
-
-static int DoC2k_is_alias(struct DiskOnChip *doc1, struct DiskOnChip *doc2)
-{
-	int tmp1, tmp2, retval;
-	if (doc1->physadr == doc2->physadr)
-		return 1;
-
-	/* Use the alias resolution register which was set aside for this
-	 * purpose. If it's value is the same on both chips, they might
-	 * be the same chip, and we write to one and check for a change in
-	 * the other. It's unclear if this register is usuable in the
-	 * DoC 2000 (it's in the Millennium docs), but it seems to work. */
-	tmp1 = ReadDOC(doc1->virtadr, AliasResolution);
-	tmp2 = ReadDOC(doc2->virtadr, AliasResolution);
-	if (tmp1 != tmp2)
-		return 0;
-
-	WriteDOC((tmp1 + 1) % 0xff, doc1->virtadr, AliasResolution);
-	tmp2 = ReadDOC(doc2->virtadr, AliasResolution);
-	if (tmp2 == (tmp1 + 1) % 0xff)
-		retval = 1;
-	else
-		retval = 0;
-
-	/* Restore register contents.  May not be necessary, but do it just to
-	 * be safe. */
-	WriteDOC(tmp1, doc1->virtadr, AliasResolution);
-
-	return retval;
-}
-
-/* This routine is found from the docprobe code by symbol_get(),
- * which will bump the use count of this module. */
-void DoC2k_init(struct mtd_info *mtd)
-{
-	struct DiskOnChip *this = mtd->priv;
-	struct DiskOnChip *old = NULL;
-	int maxchips;
-
-	/* We must avoid being called twice for the same device. */
-
-	if (doc2klist)
-		old = doc2klist->priv;
-
-	while (old) {
-		if (DoC2k_is_alias(old, this)) {
-			printk(KERN_NOTICE
-			       "Ignoring DiskOnChip 2000 at 0x%lX - already configured\n",
-			       this->physadr);
-			iounmap(this->virtadr);
-			kfree(mtd);
-			return;
-		}
-		if (old->nextdoc)
-			old = old->nextdoc->priv;
-		else
-			old = NULL;
-	}
-
-
-	switch (this->ChipID) {
-	case DOC_ChipID_Doc2kTSOP:
-		mtd->name = "DiskOnChip 2000 TSOP";
-		this->ioreg = DoC_Mil_CDSN_IO;
-		/* Pretend it's a Millennium */
-		this->ChipID = DOC_ChipID_DocMil;
-		maxchips = MAX_CHIPS;
-		break;
-	case DOC_ChipID_Doc2k:
-		mtd->name = "DiskOnChip 2000";
-		this->ioreg = DoC_2k_CDSN_IO;
-		maxchips = MAX_CHIPS;
-		break;
-	case DOC_ChipID_DocMil:
-		mtd->name = "DiskOnChip Millennium";
-		this->ioreg = DoC_Mil_CDSN_IO;
-		maxchips = MAX_CHIPS_MIL;
-		break;
-	default:
-		printk("Unknown ChipID 0x%02x\n", this->ChipID);
-		kfree(mtd);
-		iounmap(this->virtadr);
-		return;
-	}
-
-	printk(KERN_NOTICE "%s found at address 0x%lX\n", mtd->name,
-	       this->physadr);
-
-	mtd->type = MTD_NANDFLASH;
-	mtd->flags = MTD_CAP_NANDFLASH;
-	mtd->writebufsize = mtd->writesize = 512;
-	mtd->oobsize = 16;
-	mtd->ecc_strength = 2;
-	mtd->owner = THIS_MODULE;
-	mtd->_erase = doc_erase;
-	mtd->_read = doc_read;
-	mtd->_write = doc_write;
-	mtd->_read_oob = doc_read_oob;
-	mtd->_write_oob = doc_write_oob;
-	this->curfloor = -1;
-	this->curchip = -1;
-	mutex_init(&this->lock);
-
-	/* Ident all the chips present. */
-	DoC_ScanChips(this, maxchips);
-
-	if (!this->totlen) {
-		kfree(mtd);
-		iounmap(this->virtadr);
-	} else {
-		this->nextdoc = doc2klist;
-		doc2klist = mtd;
-		mtd->size = this->totlen;
-		mtd->erasesize = this->erasesize;
-		mtd_device_register(mtd, NULL, 0);
-		return;
-	}
-}
-EXPORT_SYMBOL_GPL(DoC2k_init);
-
-static int doc_read(struct mtd_info *mtd, loff_t from, size_t len,
-		    size_t * retlen, u_char * buf)
-{
-	struct DiskOnChip *this = mtd->priv;
-	void __iomem *docptr = this->virtadr;
-	struct Nand *mychip;
-	unsigned char syndrome[6], eccbuf[6];
-	volatile char dummy;
-	int i, len256 = 0, ret=0;
-	size_t left = len;
-
-	mutex_lock(&this->lock);
-	while (left) {
-		len = left;
-
-		/* Don't allow a single read to cross a 512-byte block boundary */
-		if (from + len > ((from | 0x1ff) + 1))
-			len = ((from | 0x1ff) + 1) - from;
-
-		/* The ECC will not be calculated correctly if less than 512 is read */
-		if (len != 0x200)
-			printk(KERN_WARNING
-			       "ECC needs a full sector read (adr: %lx size %lx)\n",
-			       (long) from, (long) len);
-
-		/* printk("DoC_Read (adr: %lx size %lx)\n", (long) from, (long) len); */
-
-
-		/* Find the chip which is to be used and select it */
-		mychip = &this->chips[from >> (this->chipshift)];
-
-		if (this->curfloor != mychip->floor) {
-			DoC_SelectFloor(this, mychip->floor);
-			DoC_SelectChip(this, mychip->chip);
-		} else if (this->curchip != mychip->chip) {
-			DoC_SelectChip(this, mychip->chip);
-		}
-
-		this->curfloor = mychip->floor;
-		this->curchip = mychip->chip;
-
-		DoC_Command(this,
-			    (!this->page256
-			     && (from & 0x100)) ? NAND_CMD_READ1 : NAND_CMD_READ0,
-			    CDSN_CTRL_WP);
-		DoC_Address(this, ADDR_COLUMN_PAGE, from, CDSN_CTRL_WP,
-			    CDSN_CTRL_ECC_IO);
-
-		/* Prime the ECC engine */
-		WriteDOC(DOC_ECC_RESET, docptr, ECCConf);
-		WriteDOC(DOC_ECC_EN, docptr, ECCConf);
-
-		/* treat crossing 256-byte sector for 2M x 8bits devices */
-		if (this->page256 && from + len > (from | 0xff) + 1) {
-			len256 = (from | 0xff) + 1 - from;
-			DoC_ReadBuf(this, buf, len256);
-
-			DoC_Command(this, NAND_CMD_READ0, CDSN_CTRL_WP);
-			DoC_Address(this, ADDR_COLUMN_PAGE, from + len256,
-				    CDSN_CTRL_WP, CDSN_CTRL_ECC_IO);
-		}
-
-		DoC_ReadBuf(this, &buf[len256], len - len256);
-
-		/* Let the caller know we completed it */
-		*retlen += len;
-
-		/* Read the ECC data through the DiskOnChip ECC logic */
-		/* Note: this will work even with 2M x 8bit devices as   */
-		/*       they have 8 bytes of OOB per 256 page. mf.      */
-		DoC_ReadBuf(this, eccbuf, 6);
-
-		/* Flush the pipeline */
-		if (DoC_is_Millennium(this)) {
-			dummy = ReadDOC(docptr, ECCConf);
-			dummy = ReadDOC(docptr, ECCConf);
-			i = ReadDOC(docptr, ECCConf);
-		} else {
-			dummy = ReadDOC(docptr, 2k_ECCStatus);
-			dummy = ReadDOC(docptr, 2k_ECCStatus);
-			i = ReadDOC(docptr, 2k_ECCStatus);
-		}
-
-		/* Check the ECC Status */
-		if (i & 0x80) {
-			int nb_errors;
-			/* There was an ECC error */
-#ifdef ECC_DEBUG
-			printk(KERN_ERR "DiskOnChip ECC Error: Read at %lx\n", (long)from);
-#endif
-			/* Read the ECC syndrome through the DiskOnChip ECC
-			   logic.  These syndrome will be all ZERO when there
-			   is no error */
-			for (i = 0; i < 6; i++) {
-				syndrome[i] =
-					ReadDOC(docptr, ECCSyndrome0 + i);
-			}
-			nb_errors = doc_decode_ecc(buf, syndrome);
-
-#ifdef ECC_DEBUG
-			printk(KERN_ERR "Errors corrected: %x\n", nb_errors);
-#endif
-			if (nb_errors < 0) {
-				/* We return error, but have actually done the
-				   read. Not that this can be told to
-				   user-space, via sys_read(), but at least
-				   MTD-aware stuff can know about it by
-				   checking *retlen */
-				ret = -EIO;
-			}
-		}
-
-#ifdef PSYCHO_DEBUG
-		printk(KERN_DEBUG "ECC DATA at %lxB: %2.2X %2.2X %2.2X %2.2X %2.2X %2.2X\n",
-		       (long)from, eccbuf[0], eccbuf[1], eccbuf[2],
-		       eccbuf[3], eccbuf[4], eccbuf[5]);
-#endif
-
-		/* disable the ECC engine */
-		WriteDOC(DOC_ECC_DIS, docptr , ECCConf);
-
-		/* according to 11.4.1, we need to wait for the busy line
-	         * drop if we read to the end of the page.  */
-		if(0 == ((from + len) & 0x1ff))
-		{
-		    DoC_WaitReady(this);
-		}
-
-		from += len;
-		left -= len;
-		buf += len;
-	}
-
-	mutex_unlock(&this->lock);
-
-	return ret;
-}
-
-static int doc_write(struct mtd_info *mtd, loff_t to, size_t len,
-		     size_t * retlen, const u_char * buf)
-{
-	struct DiskOnChip *this = mtd->priv;
-	int di; /* Yes, DI is a hangover from when I was disassembling the binary driver */
-	void __iomem *docptr = this->virtadr;
-	unsigned char eccbuf[6];
-	volatile char dummy;
-	int len256 = 0;
-	struct Nand *mychip;
-	size_t left = len;
-	int status;
-
-	mutex_lock(&this->lock);
-	while (left) {
-		len = left;
-
-		/* Don't allow a single write to cross a 512-byte block boundary */
-		if (to + len > ((to | 0x1ff) + 1))
-			len = ((to | 0x1ff) + 1) - to;
-
-		/* The ECC will not be calculated correctly if less than 512 is written */
-/* DBB-
-		if (len != 0x200 && eccbuf)
-			printk(KERN_WARNING
-			       "ECC needs a full sector write (adr: %lx size %lx)\n",
-			       (long) to, (long) len);
-   -DBB */
-
-		/* printk("DoC_Write (adr: %lx size %lx)\n", (long) to, (long) len); */
-
-		/* Find the chip which is to be used and select it */
-		mychip = &this->chips[to >> (this->chipshift)];
-
-		if (this->curfloor != mychip->floor) {
-			DoC_SelectFloor(this, mychip->floor);
-			DoC_SelectChip(this, mychip->chip);
-		} else if (this->curchip != mychip->chip) {
-			DoC_SelectChip(this, mychip->chip);
-		}
-
-		this->curfloor = mychip->floor;
-		this->curchip = mychip->chip;
-
-		/* Set device to main plane of flash */
-		DoC_Command(this, NAND_CMD_RESET, CDSN_CTRL_WP);
-		DoC_Command(this,
-			    (!this->page256
-			     && (to & 0x100)) ? NAND_CMD_READ1 : NAND_CMD_READ0,
-			    CDSN_CTRL_WP);
-
-		DoC_Command(this, NAND_CMD_SEQIN, 0);
-		DoC_Address(this, ADDR_COLUMN_PAGE, to, 0, CDSN_CTRL_ECC_IO);
-
-		/* Prime the ECC engine */
-		WriteDOC(DOC_ECC_RESET, docptr, ECCConf);
-		WriteDOC(DOC_ECC_EN | DOC_ECC_RW, docptr, ECCConf);
-
-		/* treat crossing 256-byte sector for 2M x 8bits devices */
-		if (this->page256 && to + len > (to | 0xff) + 1) {
-			len256 = (to | 0xff) + 1 - to;
-			DoC_WriteBuf(this, buf, len256);
-
-			DoC_Command(this, NAND_CMD_PAGEPROG, 0);
-
-			DoC_Command(this, NAND_CMD_STATUS, CDSN_CTRL_WP);
-			/* There's an implicit DoC_WaitReady() in DoC_Command */
-
-			dummy = ReadDOC(docptr, CDSNSlowIO);
-			DoC_Delay(this, 2);
-
-			if (ReadDOC_(docptr, this->ioreg) & 1) {
-				printk(KERN_ERR "Error programming flash\n");
-				/* Error in programming */
-				*retlen = 0;
-				mutex_unlock(&this->lock);
-				return -EIO;
-			}
-
-			DoC_Command(this, NAND_CMD_SEQIN, 0);
-			DoC_Address(this, ADDR_COLUMN_PAGE, to + len256, 0,
-				    CDSN_CTRL_ECC_IO);
-		}
-
-		DoC_WriteBuf(this, &buf[len256], len - len256);
-
-		WriteDOC(CDSN_CTRL_ECC_IO | CDSN_CTRL_CE, docptr, CDSNControl);
-
-		if (DoC_is_Millennium(this)) {
-			WriteDOC(0, docptr, NOP);
-			WriteDOC(0, docptr, NOP);
-			WriteDOC(0, docptr, NOP);
-		} else {
-			WriteDOC_(0, docptr, this->ioreg);
-			WriteDOC_(0, docptr, this->ioreg);
-			WriteDOC_(0, docptr, this->ioreg);
-		}
-
-		WriteDOC(CDSN_CTRL_ECC_IO | CDSN_CTRL_FLASH_IO | CDSN_CTRL_CE, docptr,
-			 CDSNControl);
-
-		/* Read the ECC data through the DiskOnChip ECC logic */
-		for (di = 0; di < 6; di++) {
-			eccbuf[di] = ReadDOC(docptr, ECCSyndrome0 + di);
-		}
-
-		/* Reset the ECC engine */
-		WriteDOC(DOC_ECC_DIS, docptr, ECCConf);
-
-#ifdef PSYCHO_DEBUG
-		printk
-			("OOB data at %lx is %2.2X %2.2X %2.2X %2.2X %2.2X %2.2X\n",
-			 (long) to, eccbuf[0], eccbuf[1], eccbuf[2], eccbuf[3],
-			 eccbuf[4], eccbuf[5]);
-#endif
-		DoC_Command(this, NAND_CMD_PAGEPROG, 0);
-
-		DoC_Command(this, NAND_CMD_STATUS, CDSN_CTRL_WP);
-		/* There's an implicit DoC_WaitReady() in DoC_Command */
-
-		if (DoC_is_Millennium(this)) {
-			ReadDOC(docptr, ReadPipeInit);
-			status = ReadDOC(docptr, LastDataRead);
-		} else {
-			dummy = ReadDOC(docptr, CDSNSlowIO);
-			DoC_Delay(this, 2);
-			status = ReadDOC_(docptr, this->ioreg);
-		}
-
-		if (status & 1) {
-			printk(KERN_ERR "Error programming flash\n");
-			/* Error in programming */
-			*retlen = 0;
-			mutex_unlock(&this->lock);
-			return -EIO;
-		}
-
-		/* Let the caller know we completed it */
-		*retlen += len;
-
-		{
-			unsigned char x[8];
-			size_t dummy;
-			int ret;
-
-			/* Write the ECC data to flash */
-			for (di=0; di<6; di++)
-				x[di] = eccbuf[di];
-
-			x[6]=0x55;
-			x[7]=0x55;
-
-			ret = doc_write_oob_nolock(mtd, to, 8, &dummy, x);
-			if (ret) {
-				mutex_unlock(&this->lock);
-				return ret;
-			}
-		}
-
-		to += len;
-		left -= len;
-		buf += len;
-	}
-
-	mutex_unlock(&this->lock);
-	return 0;
-}
-
-static int doc_read_oob(struct mtd_info *mtd, loff_t ofs,
-			struct mtd_oob_ops *ops)
-{
-	struct DiskOnChip *this = mtd->priv;
-	int len256 = 0, ret;
-	struct Nand *mychip;
-	uint8_t *buf = ops->oobbuf;
-	size_t len = ops->len;
-
-	BUG_ON(ops->mode != MTD_OPS_PLACE_OOB);
-
-	ofs += ops->ooboffs;
-
-	mutex_lock(&this->lock);
-
-	mychip = &this->chips[ofs >> this->chipshift];
-
-	if (this->curfloor != mychip->floor) {
-		DoC_SelectFloor(this, mychip->floor);
-		DoC_SelectChip(this, mychip->chip);
-	} else if (this->curchip != mychip->chip) {
-		DoC_SelectChip(this, mychip->chip);
-	}
-	this->curfloor = mychip->floor;
-	this->curchip = mychip->chip;
-
-	/* update address for 2M x 8bit devices. OOB starts on the second */
-	/* page to maintain compatibility with doc_read_ecc. */
-	if (this->page256) {
-		if (!(ofs & 0x8))
-			ofs += 0x100;
-		else
-			ofs -= 0x8;
-	}
-
-	DoC_Command(this, NAND_CMD_READOOB, CDSN_CTRL_WP);
-	DoC_Address(this, ADDR_COLUMN_PAGE, ofs, CDSN_CTRL_WP, 0);
-
-	/* treat crossing 8-byte OOB data for 2M x 8bit devices */
-	/* Note: datasheet says it should automaticaly wrap to the */
-	/*       next OOB block, but it didn't work here. mf.      */
-	if (this->page256 && ofs + len > (ofs | 0x7) + 1) {
-		len256 = (ofs | 0x7) + 1 - ofs;
-		DoC_ReadBuf(this, buf, len256);
-
-		DoC_Command(this, NAND_CMD_READOOB, CDSN_CTRL_WP);
-		DoC_Address(this, ADDR_COLUMN_PAGE, ofs & (~0x1ff),
-			    CDSN_CTRL_WP, 0);
-	}
-
-	DoC_ReadBuf(this, &buf[len256], len - len256);
-
-	ops->retlen = len;
-	/* Reading the full OOB data drops us off of the end of the page,
-         * causing the flash device to go into busy mode, so we need
-         * to wait until ready 11.4.1 and Toshiba TC58256FT docs */
-
-	ret = DoC_WaitReady(this);
-
-	mutex_unlock(&this->lock);
-	return ret;
-
-}
-
-static int doc_write_oob_nolock(struct mtd_info *mtd, loff_t ofs, size_t len,
-				size_t * retlen, const u_char * buf)
-{
-	struct DiskOnChip *this = mtd->priv;
-	int len256 = 0;
-	void __iomem *docptr = this->virtadr;
-	struct Nand *mychip = &this->chips[ofs >> this->chipshift];
-	volatile int dummy;
-	int status;
-
-	//      printk("doc_write_oob(%lx, %d): %2.2X %2.2X %2.2X %2.2X ... %2.2X %2.2X .. %2.2X %2.2X\n",(long)ofs, len,
-	//   buf[0], buf[1], buf[2], buf[3], buf[8], buf[9], buf[14],buf[15]);
-
-	/* Find the chip which is to be used and select it */
-	if (this->curfloor != mychip->floor) {
-		DoC_SelectFloor(this, mychip->floor);
-		DoC_SelectChip(this, mychip->chip);
-	} else if (this->curchip != mychip->chip) {
-		DoC_SelectChip(this, mychip->chip);
-	}
-	this->curfloor = mychip->floor;
-	this->curchip = mychip->chip;
-
-	/* disable the ECC engine */
-	WriteDOC (DOC_ECC_RESET, docptr, ECCConf);
-	WriteDOC (DOC_ECC_DIS, docptr, ECCConf);
-
-	/* Reset the chip, see Software Requirement 11.4 item 1. */
-	DoC_Command(this, NAND_CMD_RESET, CDSN_CTRL_WP);
-
-	/* issue the Read2 command to set the pointer to the Spare Data Area. */
-	DoC_Command(this, NAND_CMD_READOOB, CDSN_CTRL_WP);
-
-	/* update address for 2M x 8bit devices. OOB starts on the second */
-	/* page to maintain compatibility with doc_read_ecc. */
-	if (this->page256) {
-		if (!(ofs & 0x8))
-			ofs += 0x100;
-		else
-			ofs -= 0x8;
-	}
-
-	/* issue the Serial Data In command to initial the Page Program process */
-	DoC_Command(this, NAND_CMD_SEQIN, 0);
-	DoC_Address(this, ADDR_COLUMN_PAGE, ofs, 0, 0);
-
-	/* treat crossing 8-byte OOB data for 2M x 8bit devices */
-	/* Note: datasheet says it should automaticaly wrap to the */
-	/*       next OOB block, but it didn't work here. mf.      */
-	if (this->page256 && ofs + len > (ofs | 0x7) + 1) {
-		len256 = (ofs | 0x7) + 1 - ofs;
-		DoC_WriteBuf(this, buf, len256);
-
-		DoC_Command(this, NAND_CMD_PAGEPROG, 0);
-		DoC_Command(this, NAND_CMD_STATUS, 0);
-		/* DoC_WaitReady() is implicit in DoC_Command */
-
-		if (DoC_is_Millennium(this)) {
-			ReadDOC(docptr, ReadPipeInit);
-			status = ReadDOC(docptr, LastDataRead);
-		} else {
-			dummy = ReadDOC(docptr, CDSNSlowIO);
-			DoC_Delay(this, 2);
-			status = ReadDOC_(docptr, this->ioreg);
-		}
-
-		if (status & 1) {
-			printk(KERN_ERR "Error programming oob data\n");
-			/* There was an error */
-			*retlen = 0;
-			return -EIO;
-		}
-		DoC_Command(this, NAND_CMD_SEQIN, 0);
-		DoC_Address(this, ADDR_COLUMN_PAGE, ofs & (~0x1ff), 0, 0);
-	}
-
-	DoC_WriteBuf(this, &buf[len256], len - len256);
-
-	DoC_Command(this, NAND_CMD_PAGEPROG, 0);
-	DoC_Command(this, NAND_CMD_STATUS, 0);
-	/* DoC_WaitReady() is implicit in DoC_Command */
-
-	if (DoC_is_Millennium(this)) {
-		ReadDOC(docptr, ReadPipeInit);
-		status = ReadDOC(docptr, LastDataRead);
-	} else {
-		dummy = ReadDOC(docptr, CDSNSlowIO);
-		DoC_Delay(this, 2);
-		status = ReadDOC_(docptr, this->ioreg);
-	}
-
-	if (status & 1) {
-		printk(KERN_ERR "Error programming oob data\n");
-		/* There was an error */
-		*retlen = 0;
-		return -EIO;
-	}
-
-	*retlen = len;
-	return 0;
-
-}
-
-static int doc_write_oob(struct mtd_info *mtd, loff_t ofs,
-			 struct mtd_oob_ops *ops)
-{
-	struct DiskOnChip *this = mtd->priv;
-	int ret;
-
-	BUG_ON(ops->mode != MTD_OPS_PLACE_OOB);
-
-	mutex_lock(&this->lock);
-	ret = doc_write_oob_nolock(mtd, ofs + ops->ooboffs, ops->len,
-				   &ops->retlen, ops->oobbuf);
-
-	mutex_unlock(&this->lock);
-	return ret;
-}
-
-static int doc_erase(struct mtd_info *mtd, struct erase_info *instr)
-{
-	struct DiskOnChip *this = mtd->priv;
-	__u32 ofs = instr->addr;
-	__u32 len = instr->len;
-	volatile int dummy;
-	void __iomem *docptr = this->virtadr;
-	struct Nand *mychip;
-	int status;
-
- 	mutex_lock(&this->lock);
-
-	if (ofs & (mtd->erasesize-1) || len & (mtd->erasesize-1)) {
-		mutex_unlock(&this->lock);
-		return -EINVAL;
-	}
-
-	instr->state = MTD_ERASING;
-
-	/* FIXME: Do this in the background. Use timers or schedule_task() */
-	while(len) {
-		mychip = &this->chips[ofs >> this->chipshift];
-
-		if (this->curfloor != mychip->floor) {
-			DoC_SelectFloor(this, mychip->floor);
-			DoC_SelectChip(this, mychip->chip);
-		} else if (this->curchip != mychip->chip) {
-			DoC_SelectChip(this, mychip->chip);
-		}
-		this->curfloor = mychip->floor;
-		this->curchip = mychip->chip;
-
-		DoC_Command(this, NAND_CMD_ERASE1, 0);
-		DoC_Address(this, ADDR_PAGE, ofs, 0, 0);
-		DoC_Command(this, NAND_CMD_ERASE2, 0);
-
-		DoC_Command(this, NAND_CMD_STATUS, CDSN_CTRL_WP);
-
-		if (DoC_is_Millennium(this)) {
-			ReadDOC(docptr, ReadPipeInit);
-			status = ReadDOC(docptr, LastDataRead);
-		} else {
-			dummy = ReadDOC(docptr, CDSNSlowIO);
-			DoC_Delay(this, 2);
-			status = ReadDOC_(docptr, this->ioreg);
-		}
-
-		if (status & 1) {
-			printk(KERN_ERR "Error erasing at 0x%x\n", ofs);
-			/* There was an error */
-			instr->state = MTD_ERASE_FAILED;
-			goto callback;
-		}
-		ofs += mtd->erasesize;
-		len -= mtd->erasesize;
-	}
-	instr->state = MTD_ERASE_DONE;
-
- callback:
-	mtd_erase_callback(instr);
-
-	mutex_unlock(&this->lock);
-	return 0;
-}
-
-
-/****************************************************************************
- *
- * Module stuff
- *
- ****************************************************************************/
-
-static void __exit cleanup_doc2000(void)
-{
-	struct mtd_info *mtd;
-	struct DiskOnChip *this;
-
-	while ((mtd = doc2klist)) {
-		this = mtd->priv;
-		doc2klist = this->nextdoc;
-
-		mtd_device_unregister(mtd);
-
-		iounmap(this->virtadr);
-		kfree(this->chips);
-		kfree(mtd);
-	}
-}
-
-module_exit(cleanup_doc2000);
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("David Woodhouse <dwmw2@infradead.org> et al.");
-MODULE_DESCRIPTION("MTD driver for DiskOnChip 2000 and Millennium");
-
diff --git a/drivers/mtd/devices/doc2001.c b/drivers/mtd/devices/doc2001.c
deleted file mode 100644
index 00644bb92cdf..000000000000
--- a/drivers/mtd/devices/doc2001.c
+++ /dev/null
@@ -1,824 +0,0 @@
-
-/*
- * Linux driver for Disk-On-Chip Millennium
- * (c) 1999 Machine Vision Holdings, Inc.
- * (c) 1999, 2000 David Woodhouse <dwmw2@infradead.org>
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <asm/errno.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
-#include <linux/delay.h>
-#include <linux/slab.h>
-#include <linux/init.h>
-#include <linux/types.h>
-#include <linux/bitops.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/nand.h>
-#include <linux/mtd/doc2000.h>
-
-/* #define ECC_DEBUG */
-
-/* I have no idea why some DoC chips can not use memcop_form|to_io().
- * This may be due to the different revisions of the ASIC controller built-in or
- * simplily a QA/Bug issue. Who knows ?? If you have trouble, please uncomment
- * this:*/
-#undef USE_MEMCPY
-
-static int doc_read(struct mtd_info *mtd, loff_t from, size_t len,
-		    size_t *retlen, u_char *buf);
-static int doc_write(struct mtd_info *mtd, loff_t to, size_t len,
-		     size_t *retlen, const u_char *buf);
-static int doc_read_oob(struct mtd_info *mtd, loff_t ofs,
-			struct mtd_oob_ops *ops);
-static int doc_write_oob(struct mtd_info *mtd, loff_t ofs,
-			 struct mtd_oob_ops *ops);
-static int doc_erase (struct mtd_info *mtd, struct erase_info *instr);
-
-static struct mtd_info *docmillist = NULL;
-
-/* Perform the required delay cycles by reading from the NOP register */
-static void DoC_Delay(void __iomem * docptr, unsigned short cycles)
-{
-	volatile char dummy;
-	int i;
-
-	for (i = 0; i < cycles; i++)
-		dummy = ReadDOC(docptr, NOP);
-}
-
-/* DOC_WaitReady: Wait for RDY line to be asserted by the flash chip */
-static int _DoC_WaitReady(void __iomem * docptr)
-{
-	unsigned short c = 0xffff;
-
-	pr_debug("_DoC_WaitReady called for out-of-line wait\n");
-
-	/* Out-of-line routine to wait for chip response */
-	while (!(ReadDOC(docptr, CDSNControl) & CDSN_CTRL_FR_B) && --c)
-		;
-
-	if (c == 0)
-		pr_debug("_DoC_WaitReady timed out.\n");
-
-	return (c == 0);
-}
-
-static inline int DoC_WaitReady(void __iomem * docptr)
-{
-	/* This is inline, to optimise the common case, where it's ready instantly */
-	int ret = 0;
-
-	/* 4 read form NOP register should be issued in prior to the read from CDSNControl
-	   see Software Requirement 11.4 item 2. */
-	DoC_Delay(docptr, 4);
-
-	if (!(ReadDOC(docptr, CDSNControl) & CDSN_CTRL_FR_B))
-		/* Call the out-of-line routine to wait */
-		ret = _DoC_WaitReady(docptr);
-
-	/* issue 2 read from NOP register after reading from CDSNControl register
-	   see Software Requirement 11.4 item 2. */
-	DoC_Delay(docptr, 2);
-
-	return ret;
-}
-
-/* DoC_Command: Send a flash command to the flash chip through the CDSN IO register
-   with the internal pipeline. Each of 4 delay cycles (read from the NOP register) is
-   required after writing to CDSN Control register, see Software Requirement 11.4 item 3. */
-
-static void DoC_Command(void __iomem * docptr, unsigned char command,
-			       unsigned char xtraflags)
-{
-	/* Assert the CLE (Command Latch Enable) line to the flash chip */
-	WriteDOC(xtraflags | CDSN_CTRL_CLE | CDSN_CTRL_CE, docptr, CDSNControl);
-	DoC_Delay(docptr, 4);
-
-	/* Send the command */
-	WriteDOC(command, docptr, Mil_CDSN_IO);
-	WriteDOC(0x00, docptr, WritePipeTerm);
-
-	/* Lower the CLE line */
-	WriteDOC(xtraflags | CDSN_CTRL_CE, docptr, CDSNControl);
-	DoC_Delay(docptr, 4);
-}
-
-/* DoC_Address: Set the current address for the flash chip through the CDSN IO register
-   with the internal pipeline. Each of 4 delay cycles (read from the NOP register) is
-   required after writing to CDSN Control register, see Software Requirement 11.4 item 3. */
-
-static inline void DoC_Address(void __iomem * docptr, int numbytes, unsigned long ofs,
-			       unsigned char xtraflags1, unsigned char xtraflags2)
-{
-	/* Assert the ALE (Address Latch Enable) line to the flash chip */
-	WriteDOC(xtraflags1 | CDSN_CTRL_ALE | CDSN_CTRL_CE, docptr, CDSNControl);
-	DoC_Delay(docptr, 4);
-
-	/* Send the address */
-	switch (numbytes)
-	    {
-	    case 1:
-		    /* Send single byte, bits 0-7. */
-		    WriteDOC(ofs & 0xff, docptr, Mil_CDSN_IO);
-		    WriteDOC(0x00, docptr, WritePipeTerm);
-		    break;
-	    case 2:
-		    /* Send bits 9-16 followed by 17-23 */
-		    WriteDOC((ofs >> 9)  & 0xff, docptr, Mil_CDSN_IO);
-		    WriteDOC((ofs >> 17) & 0xff, docptr, Mil_CDSN_IO);
-		    WriteDOC(0x00, docptr, WritePipeTerm);
-		break;
-	    case 3:
-		    /* Send 0-7, 9-16, then 17-23 */
-		    WriteDOC(ofs & 0xff, docptr, Mil_CDSN_IO);
-		    WriteDOC((ofs >> 9)  & 0xff, docptr, Mil_CDSN_IO);
-		    WriteDOC((ofs >> 17) & 0xff, docptr, Mil_CDSN_IO);
-		    WriteDOC(0x00, docptr, WritePipeTerm);
-		break;
-	    default:
-		return;
-	    }
-
-	/* Lower the ALE line */
-	WriteDOC(xtraflags1 | xtraflags2 | CDSN_CTRL_CE, docptr, CDSNControl);
-	DoC_Delay(docptr, 4);
-}
-
-/* DoC_SelectChip: Select a given flash chip within the current floor */
-static int DoC_SelectChip(void __iomem * docptr, int chip)
-{
-	/* Select the individual flash chip requested */
-	WriteDOC(chip, docptr, CDSNDeviceSelect);
-	DoC_Delay(docptr, 4);
-
-	/* Wait for it to be ready */
-	return DoC_WaitReady(docptr);
-}
-
-/* DoC_SelectFloor: Select a given floor (bank of flash chips) */
-static int DoC_SelectFloor(void __iomem * docptr, int floor)
-{
-	/* Select the floor (bank) of chips required */
-	WriteDOC(floor, docptr, FloorSelect);
-
-	/* Wait for the chip to be ready */
-	return DoC_WaitReady(docptr);
-}
-
-/* DoC_IdentChip: Identify a given NAND chip given {floor,chip} */
-static int DoC_IdentChip(struct DiskOnChip *doc, int floor, int chip)
-{
-	int mfr, id, i, j;
-	volatile char dummy;
-
-	/* Page in the required floor/chip
-	   FIXME: is this supported by Millennium ?? */
-	DoC_SelectFloor(doc->virtadr, floor);
-	DoC_SelectChip(doc->virtadr, chip);
-
-	/* Reset the chip, see Software Requirement 11.4 item 1. */
-	DoC_Command(doc->virtadr, NAND_CMD_RESET, CDSN_CTRL_WP);
-	DoC_WaitReady(doc->virtadr);
-
-	/* Read the NAND chip ID: 1. Send ReadID command */
-	DoC_Command(doc->virtadr, NAND_CMD_READID, CDSN_CTRL_WP);
-
-	/* Read the NAND chip ID: 2. Send address byte zero */
-	DoC_Address(doc->virtadr, 1, 0x00, CDSN_CTRL_WP, 0x00);
-
-	/* Read the manufacturer and device id codes of the flash device through
-	   CDSN IO register see Software Requirement 11.4 item 5.*/
-	dummy = ReadDOC(doc->virtadr, ReadPipeInit);
-	DoC_Delay(doc->virtadr, 2);
-	mfr = ReadDOC(doc->virtadr, Mil_CDSN_IO);
-
-	DoC_Delay(doc->virtadr, 2);
-	id  = ReadDOC(doc->virtadr, Mil_CDSN_IO);
-	dummy = ReadDOC(doc->virtadr, LastDataRead);
-
-	/* No response - return failure */
-	if (mfr == 0xff || mfr == 0)
-		return 0;
-
-	/* FIXME: to deal with multi-flash on multi-Millennium case more carefully */
-	for (i = 0; nand_flash_ids[i].name != NULL; i++) {
-		if ( id == nand_flash_ids[i].dev_id) {
-			/* Try to identify manufacturer */
-			for (j = 0; nand_manuf_ids[j].id != 0x0; j++) {
-				if (nand_manuf_ids[j].id == mfr)
-					break;
-			}
-			printk(KERN_INFO "Flash chip found: Manufacturer ID: %2.2X, "
-			       "Chip ID: %2.2X (%s:%s)\n",
-			       mfr, id, nand_manuf_ids[j].name, nand_flash_ids[i].name);
-			doc->mfr = mfr;
-			doc->id = id;
-			doc->chipshift = ffs((nand_flash_ids[i].chipsize << 20)) - 1;
-			break;
-		}
-	}
-
-	if (nand_flash_ids[i].name == NULL)
-		return 0;
-	else
-		return 1;
-}
-
-/* DoC_ScanChips: Find all NAND chips present in a DiskOnChip, and identify them */
-static void DoC_ScanChips(struct DiskOnChip *this)
-{
-	int floor, chip;
-	int numchips[MAX_FLOORS_MIL];
-	int ret;
-
-	this->numchips = 0;
-	this->mfr = 0;
-	this->id = 0;
-
-	/* For each floor, find the number of valid chips it contains */
-	for (floor = 0,ret = 1; floor < MAX_FLOORS_MIL; floor++) {
-		numchips[floor] = 0;
-		for (chip = 0; chip < MAX_CHIPS_MIL && ret != 0; chip++) {
-			ret = DoC_IdentChip(this, floor, chip);
-			if (ret) {
-				numchips[floor]++;
-				this->numchips++;
-			}
-		}
-	}
-	/* If there are none at all that we recognise, bail */
-	if (!this->numchips) {
-		printk("No flash chips recognised.\n");
-		return;
-	}
-
-	/* Allocate an array to hold the information for each chip */
-	this->chips = kmalloc(sizeof(struct Nand) * this->numchips, GFP_KERNEL);
-	if (!this->chips){
-		printk("No memory for allocating chip info structures\n");
-		return;
-	}
-
-	/* Fill out the chip array with {floor, chipno} for each
-	 * detected chip in the device. */
-	for (floor = 0, ret = 0; floor < MAX_FLOORS_MIL; floor++) {
-		for (chip = 0 ; chip < numchips[floor] ; chip++) {
-			this->chips[ret].floor = floor;
-			this->chips[ret].chip = chip;
-			this->chips[ret].curadr = 0;
-			this->chips[ret].curmode = 0x50;
-			ret++;
-		}
-	}
-
-	/* Calculate and print the total size of the device */
-	this->totlen = this->numchips * (1 << this->chipshift);
-	printk(KERN_INFO "%d flash chips found. Total DiskOnChip size: %ld MiB\n",
-	       this->numchips ,this->totlen >> 20);
-}
-
-static int DoCMil_is_alias(struct DiskOnChip *doc1, struct DiskOnChip *doc2)
-{
-	int tmp1, tmp2, retval;
-
-	if (doc1->physadr == doc2->physadr)
-		return 1;
-
-	/* Use the alias resolution register which was set aside for this
-	 * purpose. If it's value is the same on both chips, they might
-	 * be the same chip, and we write to one and check for a change in
-	 * the other. It's unclear if this register is usuable in the
-	 * DoC 2000 (it's in the Millenium docs), but it seems to work. */
-	tmp1 = ReadDOC(doc1->virtadr, AliasResolution);
-	tmp2 = ReadDOC(doc2->virtadr, AliasResolution);
-	if (tmp1 != tmp2)
-		return 0;
-
-	WriteDOC((tmp1+1) % 0xff, doc1->virtadr, AliasResolution);
-	tmp2 = ReadDOC(doc2->virtadr, AliasResolution);
-	if (tmp2 == (tmp1+1) % 0xff)
-		retval = 1;
-	else
-		retval = 0;
-
-	/* Restore register contents.  May not be necessary, but do it just to
-	 * be safe. */
-	WriteDOC(tmp1, doc1->virtadr, AliasResolution);
-
-	return retval;
-}
-
-/* This routine is found from the docprobe code by symbol_get(),
- * which will bump the use count of this module. */
-void DoCMil_init(struct mtd_info *mtd)
-{
-	struct DiskOnChip *this = mtd->priv;
-	struct DiskOnChip *old = NULL;
-
-	/* We must avoid being called twice for the same device. */
-	if (docmillist)
-		old = docmillist->priv;
-
-	while (old) {
-		if (DoCMil_is_alias(this, old)) {
-			printk(KERN_NOTICE "Ignoring DiskOnChip Millennium at "
-			       "0x%lX - already configured\n", this->physadr);
-			iounmap(this->virtadr);
-			kfree(mtd);
-			return;
-		}
-		if (old->nextdoc)
-			old = old->nextdoc->priv;
-		else
-			old = NULL;
-	}
-
-	mtd->name = "DiskOnChip Millennium";
-	printk(KERN_NOTICE "DiskOnChip Millennium found at address 0x%lX\n",
-	       this->physadr);
-
-	mtd->type = MTD_NANDFLASH;
-	mtd->flags = MTD_CAP_NANDFLASH;
-
-	/* FIXME: erase size is not always 8KiB */
-	mtd->erasesize = 0x2000;
-	mtd->writebufsize = mtd->writesize = 512;
-	mtd->oobsize = 16;
-	mtd->ecc_strength = 2;
-	mtd->owner = THIS_MODULE;
-	mtd->_erase = doc_erase;
-	mtd->_read = doc_read;
-	mtd->_write = doc_write;
-	mtd->_read_oob = doc_read_oob;
-	mtd->_write_oob = doc_write_oob;
-	this->curfloor = -1;
-	this->curchip = -1;
-
-	/* Ident all the chips present. */
-	DoC_ScanChips(this);
-
-	if (!this->totlen) {
-		kfree(mtd);
-		iounmap(this->virtadr);
-	} else {
-		this->nextdoc = docmillist;
-		docmillist = mtd;
-		mtd->size  = this->totlen;
-		mtd_device_register(mtd, NULL, 0);
-		return;
-	}
-}
-EXPORT_SYMBOL_GPL(DoCMil_init);
-
-static int doc_read (struct mtd_info *mtd, loff_t from, size_t len,
-		     size_t *retlen, u_char *buf)
-{
-	int i, ret;
-	volatile char dummy;
-	unsigned char syndrome[6], eccbuf[6];
-	struct DiskOnChip *this = mtd->priv;
-	void __iomem *docptr = this->virtadr;
-	struct Nand *mychip = &this->chips[from >> (this->chipshift)];
-
-	/* Don't allow a single read to cross a 512-byte block boundary */
-	if (from + len > ((from | 0x1ff) + 1))
-		len = ((from | 0x1ff) + 1) - from;
-
-	/* Find the chip which is to be used and select it */
-	if (this->curfloor != mychip->floor) {
-		DoC_SelectFloor(docptr, mychip->floor);
-		DoC_SelectChip(docptr, mychip->chip);
-	} else if (this->curchip != mychip->chip) {
-		DoC_SelectChip(docptr, mychip->chip);
-	}
-	this->curfloor = mychip->floor;
-	this->curchip = mychip->chip;
-
-	/* issue the Read0 or Read1 command depend on which half of the page
-	   we are accessing. Polling the Flash Ready bit after issue 3 bytes
-	   address in Sequence Read Mode, see Software Requirement 11.4 item 1.*/
-	DoC_Command(docptr, (from >> 8) & 1, CDSN_CTRL_WP);
-	DoC_Address(docptr, 3, from, CDSN_CTRL_WP, 0x00);
-	DoC_WaitReady(docptr);
-
-	/* init the ECC engine, see Reed-Solomon EDC/ECC 11.1 .*/
-	WriteDOC (DOC_ECC_RESET, docptr, ECCConf);
-	WriteDOC (DOC_ECC_EN, docptr, ECCConf);
-
-	/* Read the data via the internal pipeline through CDSN IO register,
-	   see Pipelined Read Operations 11.3 */
-	dummy = ReadDOC(docptr, ReadPipeInit);
-#ifndef USE_MEMCPY
-	for (i = 0; i < len-1; i++) {
-		/* N.B. you have to increase the source address in this way or the
-		   ECC logic will not work properly */
-		buf[i] = ReadDOC(docptr, Mil_CDSN_IO + (i & 0xff));
-	}
-#else
-	memcpy_fromio(buf, docptr + DoC_Mil_CDSN_IO, len - 1);
-#endif
-	buf[len - 1] = ReadDOC(docptr, LastDataRead);
-
-	/* Let the caller know we completed it */
-	*retlen = len;
-        ret = 0;
-
-	/* Read the ECC data from Spare Data Area,
-	   see Reed-Solomon EDC/ECC 11.1 */
-	dummy = ReadDOC(docptr, ReadPipeInit);
-#ifndef USE_MEMCPY
-	for (i = 0; i < 5; i++) {
-		/* N.B. you have to increase the source address in this way or the
-		   ECC logic will not work properly */
-		eccbuf[i] = ReadDOC(docptr, Mil_CDSN_IO + i);
-	}
-#else
-	memcpy_fromio(eccbuf, docptr + DoC_Mil_CDSN_IO, 5);
-#endif
-	eccbuf[5] = ReadDOC(docptr, LastDataRead);
-
-	/* Flush the pipeline */
-	dummy = ReadDOC(docptr, ECCConf);
-	dummy = ReadDOC(docptr, ECCConf);
-
-	/* Check the ECC Status */
-	if (ReadDOC(docptr, ECCConf) & 0x80) {
-		int nb_errors;
-		/* There was an ECC error */
-#ifdef ECC_DEBUG
-		printk("DiskOnChip ECC Error: Read at %lx\n", (long)from);
-#endif
-		/* Read the ECC syndrome through the DiskOnChip ECC logic.
-		   These syndrome will be all ZERO when there is no error */
-		for (i = 0; i < 6; i++) {
-			syndrome[i] = ReadDOC(docptr, ECCSyndrome0 + i);
-		}
-		nb_errors = doc_decode_ecc(buf, syndrome);
-#ifdef ECC_DEBUG
-		printk("ECC Errors corrected: %x\n", nb_errors);
-#endif
-		if (nb_errors < 0) {
-			/* We return error, but have actually done the read. Not that
-			   this can be told to user-space, via sys_read(), but at least
-			   MTD-aware stuff can know about it by checking *retlen */
-			ret = -EIO;
-		}
-	}
-
-#ifdef PSYCHO_DEBUG
-	printk("ECC DATA at %lx: %2.2X %2.2X %2.2X %2.2X %2.2X %2.2X\n",
-	       (long)from, eccbuf[0], eccbuf[1], eccbuf[2], eccbuf[3],
-	       eccbuf[4], eccbuf[5]);
-#endif
-
-	/* disable the ECC engine */
-	WriteDOC(DOC_ECC_DIS, docptr , ECCConf);
-
-	return ret;
-}
-
-static int doc_write (struct mtd_info *mtd, loff_t to, size_t len,
-		      size_t *retlen, const u_char *buf)
-{
-	int i,ret = 0;
-	char eccbuf[6];
-	volatile char dummy;
-	struct DiskOnChip *this = mtd->priv;
-	void __iomem *docptr = this->virtadr;
-	struct Nand *mychip = &this->chips[to >> (this->chipshift)];
-
-#if 0
-	/* Don't allow a single write to cross a 512-byte block boundary */
-	if (to + len > ( (to | 0x1ff) + 1))
-		len = ((to | 0x1ff) + 1) - to;
-#else
-	/* Don't allow writes which aren't exactly one block */
-	if (to & 0x1ff || len != 0x200)
-		return -EINVAL;
-#endif
-
-	/* Find the chip which is to be used and select it */
-	if (this->curfloor != mychip->floor) {
-		DoC_SelectFloor(docptr, mychip->floor);
-		DoC_SelectChip(docptr, mychip->chip);
-	} else if (this->curchip != mychip->chip) {
-		DoC_SelectChip(docptr, mychip->chip);
-	}
-	this->curfloor = mychip->floor;
-	this->curchip = mychip->chip;
-
-	/* Reset the chip, see Software Requirement 11.4 item 1. */
-	DoC_Command(docptr, NAND_CMD_RESET, 0x00);
-	DoC_WaitReady(docptr);
-	/* Set device to main plane of flash */
-	DoC_Command(docptr, NAND_CMD_READ0, 0x00);
-
-	/* issue the Serial Data In command to initial the Page Program process */
-	DoC_Command(docptr, NAND_CMD_SEQIN, 0x00);
-	DoC_Address(docptr, 3, to, 0x00, 0x00);
-	DoC_WaitReady(docptr);
-
-	/* init the ECC engine, see Reed-Solomon EDC/ECC 11.1 .*/
-	WriteDOC (DOC_ECC_RESET, docptr, ECCConf);
-	WriteDOC (DOC_ECC_EN | DOC_ECC_RW, docptr, ECCConf);
-
-	/* Write the data via the internal pipeline through CDSN IO register,
-	   see Pipelined Write Operations 11.2 */
-#ifndef USE_MEMCPY
-	for (i = 0; i < len; i++) {
-		/* N.B. you have to increase the source address in this way or the
-		   ECC logic will not work properly */
-		WriteDOC(buf[i], docptr, Mil_CDSN_IO + i);
-	}
-#else
-	memcpy_toio(docptr + DoC_Mil_CDSN_IO, buf, len);
-#endif
-	WriteDOC(0x00, docptr, WritePipeTerm);
-
-	/* Write ECC data to flash, the ECC info is generated by the DiskOnChip ECC logic
-	   see Reed-Solomon EDC/ECC 11.1 */
-	WriteDOC(0, docptr, NOP);
-	WriteDOC(0, docptr, NOP);
-	WriteDOC(0, docptr, NOP);
-
-	/* Read the ECC data through the DiskOnChip ECC logic */
-	for (i = 0; i < 6; i++) {
-		eccbuf[i] = ReadDOC(docptr, ECCSyndrome0 + i);
-	}
-
-	/* ignore the ECC engine */
-	WriteDOC(DOC_ECC_DIS, docptr , ECCConf);
-
-#ifndef USE_MEMCPY
-	/* Write the ECC data to flash */
-	for (i = 0; i < 6; i++) {
-		/* N.B. you have to increase the source address in this way or the
-		   ECC logic will not work properly */
-		WriteDOC(eccbuf[i], docptr, Mil_CDSN_IO + i);
-	}
-#else
-	memcpy_toio(docptr + DoC_Mil_CDSN_IO, eccbuf, 6);
-#endif
-
-	/* write the block status BLOCK_USED (0x5555) at the end of ECC data
-	   FIXME: this is only a hack for programming the IPL area for LinuxBIOS
-	   and should be replace with proper codes in user space utilities */
-	WriteDOC(0x55, docptr, Mil_CDSN_IO);
-	WriteDOC(0x55, docptr, Mil_CDSN_IO + 1);
-
-	WriteDOC(0x00, docptr, WritePipeTerm);
-
-#ifdef PSYCHO_DEBUG
-	printk("OOB data at %lx is %2.2X %2.2X %2.2X %2.2X %2.2X %2.2X\n",
-	       (long) to, eccbuf[0], eccbuf[1], eccbuf[2], eccbuf[3],
-	       eccbuf[4], eccbuf[5]);
-#endif
-
-	/* Commit the Page Program command and wait for ready
-	   see Software Requirement 11.4 item 1.*/
-	DoC_Command(docptr, NAND_CMD_PAGEPROG, 0x00);
-	DoC_WaitReady(docptr);
-
-	/* Read the status of the flash device through CDSN IO register
-	   see Software Requirement 11.4 item 5.*/
-	DoC_Command(docptr, NAND_CMD_STATUS, CDSN_CTRL_WP);
-	dummy = ReadDOC(docptr, ReadPipeInit);
-	DoC_Delay(docptr, 2);
-	if (ReadDOC(docptr, Mil_CDSN_IO) & 1) {
-		printk("Error programming flash\n");
-		/* Error in programming
-		   FIXME: implement Bad Block Replacement (in nftl.c ??) */
-		ret = -EIO;
-	}
-	dummy = ReadDOC(docptr, LastDataRead);
-
-	/* Let the caller know we completed it */
-	*retlen = len;
-
-	return ret;
-}
-
-static int doc_read_oob(struct mtd_info *mtd, loff_t ofs,
-			struct mtd_oob_ops *ops)
-{
-#ifndef USE_MEMCPY
-	int i;
-#endif
-	volatile char dummy;
-	struct DiskOnChip *this = mtd->priv;
-	void __iomem *docptr = this->virtadr;
-	struct Nand *mychip = &this->chips[ofs >> this->chipshift];
-	uint8_t *buf = ops->oobbuf;
-	size_t len = ops->len;
-
-	BUG_ON(ops->mode != MTD_OPS_PLACE_OOB);
-
-	ofs += ops->ooboffs;
-
-	/* Find the chip which is to be used and select it */
-	if (this->curfloor != mychip->floor) {
-		DoC_SelectFloor(docptr, mychip->floor);
-		DoC_SelectChip(docptr, mychip->chip);
-	} else if (this->curchip != mychip->chip) {
-		DoC_SelectChip(docptr, mychip->chip);
-	}
-	this->curfloor = mychip->floor;
-	this->curchip = mychip->chip;
-
-	/* disable the ECC engine */
-	WriteDOC (DOC_ECC_RESET, docptr, ECCConf);
-	WriteDOC (DOC_ECC_DIS, docptr, ECCConf);
-
-	/* issue the Read2 command to set the pointer to the Spare Data Area.
-	   Polling the Flash Ready bit after issue 3 bytes address in
-	   Sequence Read Mode, see Software Requirement 11.4 item 1.*/
-	DoC_Command(docptr, NAND_CMD_READOOB, CDSN_CTRL_WP);
-	DoC_Address(docptr, 3, ofs, CDSN_CTRL_WP, 0x00);
-	DoC_WaitReady(docptr);
-
-	/* Read the data out via the internal pipeline through CDSN IO register,
-	   see Pipelined Read Operations 11.3 */
-	dummy = ReadDOC(docptr, ReadPipeInit);
-#ifndef USE_MEMCPY
-	for (i = 0; i < len-1; i++) {
-		/* N.B. you have to increase the source address in this way or the
-		   ECC logic will not work properly */
-		buf[i] = ReadDOC(docptr, Mil_CDSN_IO + i);
-	}
-#else
-	memcpy_fromio(buf, docptr + DoC_Mil_CDSN_IO, len - 1);
-#endif
-	buf[len - 1] = ReadDOC(docptr, LastDataRead);
-
-	ops->retlen = len;
-
-	return 0;
-}
-
-static int doc_write_oob(struct mtd_info *mtd, loff_t ofs,
-			 struct mtd_oob_ops *ops)
-{
-#ifndef USE_MEMCPY
-	int i;
-#endif
-	volatile char dummy;
-	int ret = 0;
-	struct DiskOnChip *this = mtd->priv;
-	void __iomem *docptr = this->virtadr;
-	struct Nand *mychip = &this->chips[ofs >> this->chipshift];
-	uint8_t *buf = ops->oobbuf;
-	size_t len = ops->len;
-
-	BUG_ON(ops->mode != MTD_OPS_PLACE_OOB);
-
-	ofs += ops->ooboffs;
-
-	/* Find the chip which is to be used and select it */
-	if (this->curfloor != mychip->floor) {
-		DoC_SelectFloor(docptr, mychip->floor);
-		DoC_SelectChip(docptr, mychip->chip);
-	} else if (this->curchip != mychip->chip) {
-		DoC_SelectChip(docptr, mychip->chip);
-	}
-	this->curfloor = mychip->floor;
-	this->curchip = mychip->chip;
-
-	/* disable the ECC engine */
-	WriteDOC (DOC_ECC_RESET, docptr, ECCConf);
-	WriteDOC (DOC_ECC_DIS, docptr, ECCConf);
-
-	/* Reset the chip, see Software Requirement 11.4 item 1. */
-	DoC_Command(docptr, NAND_CMD_RESET, CDSN_CTRL_WP);
-	DoC_WaitReady(docptr);
-	/* issue the Read2 command to set the pointer to the Spare Data Area. */
-	DoC_Command(docptr, NAND_CMD_READOOB, CDSN_CTRL_WP);
-
-	/* issue the Serial Data In command to initial the Page Program process */
-	DoC_Command(docptr, NAND_CMD_SEQIN, 0x00);
-	DoC_Address(docptr, 3, ofs, 0x00, 0x00);
-
-	/* Write the data via the internal pipeline through CDSN IO register,
-	   see Pipelined Write Operations 11.2 */
-#ifndef USE_MEMCPY
-	for (i = 0; i < len; i++) {
-		/* N.B. you have to increase the source address in this way or the
-		   ECC logic will not work properly */
-		WriteDOC(buf[i], docptr, Mil_CDSN_IO + i);
-	}
-#else
-	memcpy_toio(docptr + DoC_Mil_CDSN_IO, buf, len);
-#endif
-	WriteDOC(0x00, docptr, WritePipeTerm);
-
-	/* Commit the Page Program command and wait for ready
-	   see Software Requirement 11.4 item 1.*/
-	DoC_Command(docptr, NAND_CMD_PAGEPROG, 0x00);
-	DoC_WaitReady(docptr);
-
-	/* Read the status of the flash device through CDSN IO register
-	   see Software Requirement 11.4 item 5.*/
-	DoC_Command(docptr, NAND_CMD_STATUS, 0x00);
-	dummy = ReadDOC(docptr, ReadPipeInit);
-	DoC_Delay(docptr, 2);
-	if (ReadDOC(docptr, Mil_CDSN_IO) & 1) {
-		printk("Error programming oob data\n");
-		/* FIXME: implement Bad Block Replacement (in nftl.c ??) */
-		ops->retlen = 0;
-		ret = -EIO;
-	}
-	dummy = ReadDOC(docptr, LastDataRead);
-
-	ops->retlen = len;
-
-	return ret;
-}
-
-int doc_erase (struct mtd_info *mtd, struct erase_info *instr)
-{
-	volatile char dummy;
-	struct DiskOnChip *this = mtd->priv;
-	__u32 ofs = instr->addr;
-	__u32 len = instr->len;
-	void __iomem *docptr = this->virtadr;
-	struct Nand *mychip = &this->chips[ofs >> this->chipshift];
-
-	if (len != mtd->erasesize)
-		printk(KERN_WARNING "Erase not right size (%x != %x)n",
-		       len, mtd->erasesize);
-
-	/* Find the chip which is to be used and select it */
-	if (this->curfloor != mychip->floor) {
-		DoC_SelectFloor(docptr, mychip->floor);
-		DoC_SelectChip(docptr, mychip->chip);
-	} else if (this->curchip != mychip->chip) {
-		DoC_SelectChip(docptr, mychip->chip);
-	}
-	this->curfloor = mychip->floor;
-	this->curchip = mychip->chip;
-
-	instr->state = MTD_ERASE_PENDING;
-
-	/* issue the Erase Setup command */
-	DoC_Command(docptr, NAND_CMD_ERASE1, 0x00);
-	DoC_Address(docptr, 2, ofs, 0x00, 0x00);
-
-	/* Commit the Erase Start command and wait for ready
-	   see Software Requirement 11.4 item 1.*/
-	DoC_Command(docptr, NAND_CMD_ERASE2, 0x00);
-	DoC_WaitReady(docptr);
-
-	instr->state = MTD_ERASING;
-
-	/* Read the status of the flash device through CDSN IO register
-	   see Software Requirement 11.4 item 5.
-	   FIXME: it seems that we are not wait long enough, some blocks are not
-	   erased fully */
-	DoC_Command(docptr, NAND_CMD_STATUS, CDSN_CTRL_WP);
-	dummy = ReadDOC(docptr, ReadPipeInit);
-	DoC_Delay(docptr, 2);
-	if (ReadDOC(docptr, Mil_CDSN_IO) & 1) {
-		printk("Error Erasing at 0x%x\n", ofs);
-		/* There was an error
-		   FIXME: implement Bad Block Replacement (in nftl.c ??) */
-		instr->state = MTD_ERASE_FAILED;
-	} else
-		instr->state = MTD_ERASE_DONE;
-	dummy = ReadDOC(docptr, LastDataRead);
-
-	mtd_erase_callback(instr);
-
-	return 0;
-}
-
-/****************************************************************************
- *
- * Module stuff
- *
- ****************************************************************************/
-
-static void __exit cleanup_doc2001(void)
-{
-	struct mtd_info *mtd;
-	struct DiskOnChip *this;
-
-	while ((mtd=docmillist)) {
-		this = mtd->priv;
-		docmillist = this->nextdoc;
-
-		mtd_device_unregister(mtd);
-
-		iounmap(this->virtadr);
-		kfree(this->chips);
-		kfree(mtd);
-	}
-}
-
-module_exit(cleanup_doc2001);
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("David Woodhouse <dwmw2@infradead.org> et al.");
-MODULE_DESCRIPTION("Alternative driver for DiskOnChip Millennium");
diff --git a/drivers/mtd/devices/doc2001plus.c b/drivers/mtd/devices/doc2001plus.c
deleted file mode 100644
index 1b0c12f3ec02..000000000000
--- a/drivers/mtd/devices/doc2001plus.c
+++ /dev/null
@@ -1,1080 +0,0 @@
-/*
- * Linux driver for Disk-On-Chip Millennium Plus
- *
- * (c) 2002-2003 Greg Ungerer <gerg@snapgear.com>
- * (c) 2002-2003 SnapGear Inc
- * (c) 1999 Machine Vision Holdings, Inc.
- * (c) 1999, 2000 David Woodhouse <dwmw2@infradead.org>
- *
- * Released under GPL
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <asm/errno.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
-#include <linux/delay.h>
-#include <linux/slab.h>
-#include <linux/init.h>
-#include <linux/types.h>
-#include <linux/bitops.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/nand.h>
-#include <linux/mtd/doc2000.h>
-
-/* #define ECC_DEBUG */
-
-/* I have no idea why some DoC chips can not use memcop_form|to_io().
- * This may be due to the different revisions of the ASIC controller built-in or
- * simplily a QA/Bug issue. Who knows ?? If you have trouble, please uncomment
- * this:*/
-#undef USE_MEMCPY
-
-static int doc_read(struct mtd_info *mtd, loff_t from, size_t len,
-		size_t *retlen, u_char *buf);
-static int doc_write(struct mtd_info *mtd, loff_t to, size_t len,
-		size_t *retlen, const u_char *buf);
-static int doc_read_oob(struct mtd_info *mtd, loff_t ofs,
-			struct mtd_oob_ops *ops);
-static int doc_write_oob(struct mtd_info *mtd, loff_t ofs,
-			 struct mtd_oob_ops *ops);
-static int doc_erase (struct mtd_info *mtd, struct erase_info *instr);
-
-static struct mtd_info *docmilpluslist = NULL;
-
-
-/* Perform the required delay cycles by writing to the NOP register */
-static void DoC_Delay(void __iomem * docptr, int cycles)
-{
-	int i;
-
-	for (i = 0; (i < cycles); i++)
-		WriteDOC(0, docptr, Mplus_NOP);
-}
-
-#define	CDSN_CTRL_FR_B_MASK	(CDSN_CTRL_FR_B0 | CDSN_CTRL_FR_B1)
-
-/* DOC_WaitReady: Wait for RDY line to be asserted by the flash chip */
-static int _DoC_WaitReady(void __iomem * docptr)
-{
-	unsigned int c = 0xffff;
-
-	pr_debug("_DoC_WaitReady called for out-of-line wait\n");
-
-	/* Out-of-line routine to wait for chip response */
-	while (((ReadDOC(docptr, Mplus_FlashControl) & CDSN_CTRL_FR_B_MASK) != CDSN_CTRL_FR_B_MASK) && --c)
-		;
-
-	if (c == 0)
-		pr_debug("_DoC_WaitReady timed out.\n");
-
-	return (c == 0);
-}
-
-static inline int DoC_WaitReady(void __iomem * docptr)
-{
-	/* This is inline, to optimise the common case, where it's ready instantly */
-	int ret = 0;
-
-	/* read form NOP register should be issued prior to the read from CDSNControl
-	   see Software Requirement 11.4 item 2. */
-	DoC_Delay(docptr, 4);
-
-	if ((ReadDOC(docptr, Mplus_FlashControl) & CDSN_CTRL_FR_B_MASK) != CDSN_CTRL_FR_B_MASK)
-		/* Call the out-of-line routine to wait */
-		ret = _DoC_WaitReady(docptr);
-
-	return ret;
-}
-
-/* For some reason the Millennium Plus seems to occasionally put itself
- * into reset mode. For me this happens randomly, with no pattern that I
- * can detect. M-systems suggest always check this on any block level
- * operation and setting to normal mode if in reset mode.
- */
-static inline void DoC_CheckASIC(void __iomem * docptr)
-{
-	/* Make sure the DoC is in normal mode */
-	if ((ReadDOC(docptr, Mplus_DOCControl) & DOC_MODE_NORMAL) == 0) {
-		WriteDOC((DOC_MODE_NORMAL | DOC_MODE_MDWREN), docptr, Mplus_DOCControl);
-		WriteDOC(~(DOC_MODE_NORMAL | DOC_MODE_MDWREN), docptr, Mplus_CtrlConfirm);
-	}
-}
-
-/* DoC_Command: Send a flash command to the flash chip through the Flash
- * command register. Need 2 Write Pipeline Terminates to complete send.
- */
-static void DoC_Command(void __iomem * docptr, unsigned char command,
-			       unsigned char xtraflags)
-{
-	WriteDOC(command, docptr, Mplus_FlashCmd);
-	WriteDOC(command, docptr, Mplus_WritePipeTerm);
-	WriteDOC(command, docptr, Mplus_WritePipeTerm);
-}
-
-/* DoC_Address: Set the current address for the flash chip through the Flash
- * Address register. Need 2 Write Pipeline Terminates to complete send.
- */
-static inline void DoC_Address(struct DiskOnChip *doc, int numbytes,
-			       unsigned long ofs, unsigned char xtraflags1,
-			       unsigned char xtraflags2)
-{
-	void __iomem * docptr = doc->virtadr;
-
-	/* Allow for possible Mill Plus internal flash interleaving */
-	ofs >>= doc->interleave;
-
-	switch (numbytes) {
-	case 1:
-		/* Send single byte, bits 0-7. */
-		WriteDOC(ofs & 0xff, docptr, Mplus_FlashAddress);
-		break;
-	case 2:
-		/* Send bits 9-16 followed by 17-23 */
-		WriteDOC((ofs >> 9)  & 0xff, docptr, Mplus_FlashAddress);
-		WriteDOC((ofs >> 17) & 0xff, docptr, Mplus_FlashAddress);
-		break;
-	case 3:
-		/* Send 0-7, 9-16, then 17-23 */
-		WriteDOC(ofs & 0xff, docptr, Mplus_FlashAddress);
-		WriteDOC((ofs >> 9)  & 0xff, docptr, Mplus_FlashAddress);
-		WriteDOC((ofs >> 17) & 0xff, docptr, Mplus_FlashAddress);
-		break;
-	default:
-		return;
-	}
-
-	WriteDOC(0x00, docptr, Mplus_WritePipeTerm);
-	WriteDOC(0x00, docptr, Mplus_WritePipeTerm);
-}
-
-/* DoC_SelectChip: Select a given flash chip within the current floor */
-static int DoC_SelectChip(void __iomem * docptr, int chip)
-{
-	/* No choice for flash chip on Millennium Plus */
-	return 0;
-}
-
-/* DoC_SelectFloor: Select a given floor (bank of flash chips) */
-static int DoC_SelectFloor(void __iomem * docptr, int floor)
-{
-	WriteDOC((floor & 0x3), docptr, Mplus_DeviceSelect);
-	return 0;
-}
-
-/*
- * Translate the given offset into the appropriate command and offset.
- * This does the mapping using the 16bit interleave layout defined by
- * M-Systems, and looks like this for a sector pair:
- *  +-----------+-------+-------+-------+--------------+---------+-----------+
- *  | 0 --- 511 |512-517|518-519|520-521| 522 --- 1033 |1034-1039|1040 - 1055|
- *  +-----------+-------+-------+-------+--------------+---------+-----------+
- *  | Data 0    | ECC 0 |Flags0 |Flags1 | Data 1       |ECC 1    | OOB 1 + 2 |
- *  +-----------+-------+-------+-------+--------------+---------+-----------+
- */
-/* FIXME: This lives in INFTL not here. Other users of flash devices
-   may not want it */
-static unsigned int DoC_GetDataOffset(struct mtd_info *mtd, loff_t *from)
-{
-	struct DiskOnChip *this = mtd->priv;
-
-	if (this->interleave) {
-		unsigned int ofs = *from & 0x3ff;
-		unsigned int cmd;
-
-		if (ofs < 512) {
-			cmd = NAND_CMD_READ0;
-			ofs &= 0x1ff;
-		} else if (ofs < 1014) {
-			cmd = NAND_CMD_READ1;
-			ofs = (ofs & 0x1ff) + 10;
-		} else {
-			cmd = NAND_CMD_READOOB;
-			ofs = ofs - 1014;
-		}
-
-		*from = (*from & ~0x3ff) | ofs;
-		return cmd;
-	} else {
-		/* No interleave */
-		if ((*from) & 0x100)
-			return NAND_CMD_READ1;
-		return NAND_CMD_READ0;
-	}
-}
-
-static unsigned int DoC_GetECCOffset(struct mtd_info *mtd, loff_t *from)
-{
-	unsigned int ofs, cmd;
-
-	if (*from & 0x200) {
-		cmd = NAND_CMD_READOOB;
-		ofs = 10 + (*from & 0xf);
-	} else {
-		cmd = NAND_CMD_READ1;
-		ofs = (*from & 0xf);
-	}
-
-	*from = (*from & ~0x3ff) | ofs;
-	return cmd;
-}
-
-static unsigned int DoC_GetFlagsOffset(struct mtd_info *mtd, loff_t *from)
-{
-	unsigned int ofs, cmd;
-
-	cmd = NAND_CMD_READ1;
-	ofs = (*from & 0x200) ? 8 : 6;
-	*from = (*from & ~0x3ff) | ofs;
-	return cmd;
-}
-
-static unsigned int DoC_GetHdrOffset(struct mtd_info *mtd, loff_t *from)
-{
-	unsigned int ofs, cmd;
-
-	cmd = NAND_CMD_READOOB;
-	ofs = (*from & 0x200) ? 24 : 16;
-	*from = (*from & ~0x3ff) | ofs;
-	return cmd;
-}
-
-static inline void MemReadDOC(void __iomem * docptr, unsigned char *buf, int len)
-{
-#ifndef USE_MEMCPY
-	int i;
-	for (i = 0; i < len; i++)
-		buf[i] = ReadDOC(docptr, Mil_CDSN_IO + i);
-#else
-	memcpy_fromio(buf, docptr + DoC_Mil_CDSN_IO, len);
-#endif
-}
-
-static inline void MemWriteDOC(void __iomem * docptr, unsigned char *buf, int len)
-{
-#ifndef USE_MEMCPY
-	int i;
-	for (i = 0; i < len; i++)
-		WriteDOC(buf[i], docptr, Mil_CDSN_IO + i);
-#else
-	memcpy_toio(docptr + DoC_Mil_CDSN_IO, buf, len);
-#endif
-}
-
-/* DoC_IdentChip: Identify a given NAND chip given {floor,chip} */
-static int DoC_IdentChip(struct DiskOnChip *doc, int floor, int chip)
-{
-	int mfr, id, i, j;
-	volatile char dummy;
-	void __iomem * docptr = doc->virtadr;
-
-	/* Page in the required floor/chip */
-	DoC_SelectFloor(docptr, floor);
-	DoC_SelectChip(docptr, chip);
-
-	/* Millennium Plus bus cycle sequence as per figure 2, section 2.4 */
-	WriteDOC((DOC_FLASH_CE | DOC_FLASH_WP), docptr, Mplus_FlashSelect);
-
-	/* Reset the chip, see Software Requirement 11.4 item 1. */
-	DoC_Command(docptr, NAND_CMD_RESET, 0);
-	DoC_WaitReady(docptr);
-
-	/* Read the NAND chip ID: 1. Send ReadID command */
-	DoC_Command(docptr, NAND_CMD_READID, 0);
-
-	/* Read the NAND chip ID: 2. Send address byte zero */
-	DoC_Address(doc, 1, 0x00, 0, 0x00);
-
-	WriteDOC(0, docptr, Mplus_FlashControl);
-	DoC_WaitReady(docptr);
-
-	/* Read the manufacturer and device id codes of the flash device through
-	   CDSN IO register see Software Requirement 11.4 item 5.*/
-	dummy = ReadDOC(docptr, Mplus_ReadPipeInit);
-	dummy = ReadDOC(docptr, Mplus_ReadPipeInit);
-
-	mfr = ReadDOC(docptr, Mil_CDSN_IO);
-	if (doc->interleave)
-		dummy = ReadDOC(docptr, Mil_CDSN_IO); /* 2 way interleave */
-
-	id  = ReadDOC(docptr, Mil_CDSN_IO);
-	if (doc->interleave)
-		dummy = ReadDOC(docptr, Mil_CDSN_IO); /* 2 way interleave */
-
-	dummy = ReadDOC(docptr, Mplus_LastDataRead);
-	dummy = ReadDOC(docptr, Mplus_LastDataRead);
-
-	/* Disable flash internally */
-	WriteDOC(0, docptr, Mplus_FlashSelect);
-
-	/* No response - return failure */
-	if (mfr == 0xff || mfr == 0)
-		return 0;
-
-	for (i = 0; nand_flash_ids[i].name != NULL; i++) {
-		if (id == nand_flash_ids[i].dev_id) {
-			/* Try to identify manufacturer */
-			for (j = 0; nand_manuf_ids[j].id != 0x0; j++) {
-				if (nand_manuf_ids[j].id == mfr)
-					break;
-			}
-			printk(KERN_INFO "Flash chip found: Manufacturer ID: %2.2X, "
-			       "Chip ID: %2.2X (%s:%s)\n", mfr, id,
-			       nand_manuf_ids[j].name, nand_flash_ids[i].name);
-			doc->mfr = mfr;
-			doc->id = id;
-			doc->chipshift = ffs((nand_flash_ids[i].chipsize << 20)) - 1;
-			doc->erasesize = nand_flash_ids[i].erasesize << doc->interleave;
-			break;
-		}
-	}
-
-	if (nand_flash_ids[i].name == NULL)
-		return 0;
-	return 1;
-}
-
-/* DoC_ScanChips: Find all NAND chips present in a DiskOnChip, and identify them */
-static void DoC_ScanChips(struct DiskOnChip *this)
-{
-	int floor, chip;
-	int numchips[MAX_FLOORS_MPLUS];
-	int ret;
-
-	this->numchips = 0;
-	this->mfr = 0;
-	this->id = 0;
-
-	/* Work out the intended interleave setting */
-	this->interleave = 0;
-	if (this->ChipID == DOC_ChipID_DocMilPlus32)
-		this->interleave = 1;
-
-	/* Check the ASIC agrees */
-	if ( (this->interleave << 2) !=
-	     (ReadDOC(this->virtadr, Mplus_Configuration) & 4)) {
-		u_char conf = ReadDOC(this->virtadr, Mplus_Configuration);
-		printk(KERN_NOTICE "Setting DiskOnChip Millennium Plus interleave to %s\n",
-		       this->interleave?"on (16-bit)":"off (8-bit)");
-		conf ^= 4;
-		WriteDOC(conf, this->virtadr, Mplus_Configuration);
-	}
-
-	/* For each floor, find the number of valid chips it contains */
-	for (floor = 0,ret = 1; floor < MAX_FLOORS_MPLUS; floor++) {
-		numchips[floor] = 0;
-		for (chip = 0; chip < MAX_CHIPS_MPLUS && ret != 0; chip++) {
-			ret = DoC_IdentChip(this, floor, chip);
-			if (ret) {
-				numchips[floor]++;
-				this->numchips++;
-			}
-		}
-	}
-	/* If there are none at all that we recognise, bail */
-	if (!this->numchips) {
-		printk("No flash chips recognised.\n");
-		return;
-	}
-
-	/* Allocate an array to hold the information for each chip */
-	this->chips = kmalloc(sizeof(struct Nand) * this->numchips, GFP_KERNEL);
-	if (!this->chips){
-		printk("MTD: No memory for allocating chip info structures\n");
-		return;
-	}
-
-	/* Fill out the chip array with {floor, chipno} for each
-	 * detected chip in the device. */
-	for (floor = 0, ret = 0; floor < MAX_FLOORS_MPLUS; floor++) {
-		for (chip = 0 ; chip < numchips[floor] ; chip++) {
-			this->chips[ret].floor = floor;
-			this->chips[ret].chip = chip;
-			this->chips[ret].curadr = 0;
-			this->chips[ret].curmode = 0x50;
-			ret++;
-		}
-	}
-
-	/* Calculate and print the total size of the device */
-	this->totlen = this->numchips * (1 << this->chipshift);
-	printk(KERN_INFO "%d flash chips found. Total DiskOnChip size: %ld MiB\n",
-	       this->numchips ,this->totlen >> 20);
-}
-
-static int DoCMilPlus_is_alias(struct DiskOnChip *doc1, struct DiskOnChip *doc2)
-{
-	int tmp1, tmp2, retval;
-
-	if (doc1->physadr == doc2->physadr)
-		return 1;
-
-	/* Use the alias resolution register which was set aside for this
-	 * purpose. If it's value is the same on both chips, they might
-	 * be the same chip, and we write to one and check for a change in
-	 * the other. It's unclear if this register is usuable in the
-	 * DoC 2000 (it's in the Millennium docs), but it seems to work. */
-	tmp1 = ReadDOC(doc1->virtadr, Mplus_AliasResolution);
-	tmp2 = ReadDOC(doc2->virtadr, Mplus_AliasResolution);
-	if (tmp1 != tmp2)
-		return 0;
-
-	WriteDOC((tmp1+1) % 0xff, doc1->virtadr, Mplus_AliasResolution);
-	tmp2 = ReadDOC(doc2->virtadr, Mplus_AliasResolution);
-	if (tmp2 == (tmp1+1) % 0xff)
-		retval = 1;
-	else
-		retval = 0;
-
-	/* Restore register contents.  May not be necessary, but do it just to
-	 * be safe. */
-	WriteDOC(tmp1, doc1->virtadr, Mplus_AliasResolution);
-
-	return retval;
-}
-
-/* This routine is found from the docprobe code by symbol_get(),
- * which will bump the use count of this module. */
-void DoCMilPlus_init(struct mtd_info *mtd)
-{
-	struct DiskOnChip *this = mtd->priv;
-	struct DiskOnChip *old = NULL;
-
-	/* We must avoid being called twice for the same device. */
-	if (docmilpluslist)
-		old = docmilpluslist->priv;
-
-	while (old) {
-		if (DoCMilPlus_is_alias(this, old)) {
-			printk(KERN_NOTICE "Ignoring DiskOnChip Millennium "
-				"Plus at 0x%lX - already configured\n",
-				this->physadr);
-			iounmap(this->virtadr);
-			kfree(mtd);
-			return;
-		}
-		if (old->nextdoc)
-			old = old->nextdoc->priv;
-		else
-			old = NULL;
-	}
-
-	mtd->name = "DiskOnChip Millennium Plus";
-	printk(KERN_NOTICE "DiskOnChip Millennium Plus found at "
-		"address 0x%lX\n", this->physadr);
-
-	mtd->type = MTD_NANDFLASH;
-	mtd->flags = MTD_CAP_NANDFLASH;
-	mtd->writebufsize = mtd->writesize = 512;
-	mtd->oobsize = 16;
-	mtd->ecc_strength = 2;
-	mtd->owner = THIS_MODULE;
-	mtd->_erase = doc_erase;
-	mtd->_read = doc_read;
-	mtd->_write = doc_write;
-	mtd->_read_oob = doc_read_oob;
-	mtd->_write_oob = doc_write_oob;
-	this->curfloor = -1;
-	this->curchip = -1;
-
-	/* Ident all the chips present. */
-	DoC_ScanChips(this);
-
-	if (!this->totlen) {
-		kfree(mtd);
-		iounmap(this->virtadr);
-	} else {
-		this->nextdoc = docmilpluslist;
-		docmilpluslist = mtd;
-		mtd->size  = this->totlen;
-		mtd->erasesize = this->erasesize;
-		mtd_device_register(mtd, NULL, 0);
-		return;
-	}
-}
-EXPORT_SYMBOL_GPL(DoCMilPlus_init);
-
-#if 0
-static int doc_dumpblk(struct mtd_info *mtd, loff_t from)
-{
-	int i;
-	loff_t fofs;
-	struct DiskOnChip *this = mtd->priv;
-	void __iomem * docptr = this->virtadr;
-	struct Nand *mychip = &this->chips[from >> (this->chipshift)];
-	unsigned char *bp, buf[1056];
-	char c[32];
-
-	from &= ~0x3ff;
-
-	/* Don't allow read past end of device */
-	if (from >= this->totlen)
-		return -EINVAL;
-
-	DoC_CheckASIC(docptr);
-
-	/* Find the chip which is to be used and select it */
-	if (this->curfloor != mychip->floor) {
-		DoC_SelectFloor(docptr, mychip->floor);
-		DoC_SelectChip(docptr, mychip->chip);
-	} else if (this->curchip != mychip->chip) {
-		DoC_SelectChip(docptr, mychip->chip);
-	}
-	this->curfloor = mychip->floor;
-	this->curchip = mychip->chip;
-
-	/* Millennium Plus bus cycle sequence as per figure 2, section 2.4 */
-	WriteDOC((DOC_FLASH_CE | DOC_FLASH_WP), docptr, Mplus_FlashSelect);
-
-	/* Reset the chip, see Software Requirement 11.4 item 1. */
-	DoC_Command(docptr, NAND_CMD_RESET, 0);
-	DoC_WaitReady(docptr);
-
-	fofs = from;
-	DoC_Command(docptr, DoC_GetDataOffset(mtd, &fofs), 0);
-	DoC_Address(this, 3, fofs, 0, 0x00);
-	WriteDOC(0, docptr, Mplus_FlashControl);
-	DoC_WaitReady(docptr);
-
-	/* disable the ECC engine */
-	WriteDOC(DOC_ECC_RESET, docptr, Mplus_ECCConf);
-
-	ReadDOC(docptr, Mplus_ReadPipeInit);
-	ReadDOC(docptr, Mplus_ReadPipeInit);
-
-	/* Read the data via the internal pipeline through CDSN IO
-	   register, see Pipelined Read Operations 11.3 */
-	MemReadDOC(docptr, buf, 1054);
-	buf[1054] = ReadDOC(docptr, Mplus_LastDataRead);
-	buf[1055] = ReadDOC(docptr, Mplus_LastDataRead);
-
-	memset(&c[0], 0, sizeof(c));
-	printk("DUMP OFFSET=%x:\n", (int)from);
-
-        for (i = 0, bp = &buf[0]; (i < 1056); i++) {
-                if ((i % 16) == 0)
-                        printk("%08x: ", i);
-                printk(" %02x", *bp);
-                c[(i & 0xf)] = ((*bp >= 0x20) && (*bp <= 0x7f)) ? *bp : '.';
-                bp++;
-                if (((i + 1) % 16) == 0)
-                        printk("    %s\n", c);
-        }
-	printk("\n");
-
-	/* Disable flash internally */
-	WriteDOC(0, docptr, Mplus_FlashSelect);
-
-	return 0;
-}
-#endif
-
-static int doc_read(struct mtd_info *mtd, loff_t from, size_t len,
-		    size_t *retlen, u_char *buf)
-{
-	int ret, i;
-	volatile char dummy;
-	loff_t fofs;
-	unsigned char syndrome[6], eccbuf[6];
-	struct DiskOnChip *this = mtd->priv;
-	void __iomem * docptr = this->virtadr;
-	struct Nand *mychip = &this->chips[from >> (this->chipshift)];
-
-	/* Don't allow a single read to cross a 512-byte block boundary */
-	if (from + len > ((from | 0x1ff) + 1))
-		len = ((from | 0x1ff) + 1) - from;
-
-	DoC_CheckASIC(docptr);
-
-	/* Find the chip which is to be used and select it */
-	if (this->curfloor != mychip->floor) {
-		DoC_SelectFloor(docptr, mychip->floor);
-		DoC_SelectChip(docptr, mychip->chip);
-	} else if (this->curchip != mychip->chip) {
-		DoC_SelectChip(docptr, mychip->chip);
-	}
-	this->curfloor = mychip->floor;
-	this->curchip = mychip->chip;
-
-	/* Millennium Plus bus cycle sequence as per figure 2, section 2.4 */
-	WriteDOC((DOC_FLASH_CE | DOC_FLASH_WP), docptr, Mplus_FlashSelect);
-
-	/* Reset the chip, see Software Requirement 11.4 item 1. */
-	DoC_Command(docptr, NAND_CMD_RESET, 0);
-	DoC_WaitReady(docptr);
-
-	fofs = from;
-	DoC_Command(docptr, DoC_GetDataOffset(mtd, &fofs), 0);
-	DoC_Address(this, 3, fofs, 0, 0x00);
-	WriteDOC(0, docptr, Mplus_FlashControl);
-	DoC_WaitReady(docptr);
-
-	/* init the ECC engine, see Reed-Solomon EDC/ECC 11.1 .*/
-	WriteDOC(DOC_ECC_RESET, docptr, Mplus_ECCConf);
-	WriteDOC(DOC_ECC_EN, docptr, Mplus_ECCConf);
-
-	/* Let the caller know we completed it */
-	*retlen = len;
-	ret = 0;
-
-	ReadDOC(docptr, Mplus_ReadPipeInit);
-	ReadDOC(docptr, Mplus_ReadPipeInit);
-
-	/* Read the data via the internal pipeline through CDSN IO
-	   register, see Pipelined Read Operations 11.3 */
-	MemReadDOC(docptr, buf, len);
-
-	/* Read the ECC data following raw data */
-	MemReadDOC(docptr, eccbuf, 4);
-	eccbuf[4] = ReadDOC(docptr, Mplus_LastDataRead);
-	eccbuf[5] = ReadDOC(docptr, Mplus_LastDataRead);
-
-	/* Flush the pipeline */
-	dummy = ReadDOC(docptr, Mplus_ECCConf);
-	dummy = ReadDOC(docptr, Mplus_ECCConf);
-
-	/* Check the ECC Status */
-	if (ReadDOC(docptr, Mplus_ECCConf) & 0x80) {
-		int nb_errors;
-		/* There was an ECC error */
-#ifdef ECC_DEBUG
-		printk("DiskOnChip ECC Error: Read at %lx\n", (long)from);
-#endif
-		/* Read the ECC syndrome through the DiskOnChip ECC logic.
-		   These syndrome will be all ZERO when there is no error */
-		for (i = 0; i < 6; i++)
-			syndrome[i] = ReadDOC(docptr, Mplus_ECCSyndrome0 + i);
-
-		nb_errors = doc_decode_ecc(buf, syndrome);
-#ifdef ECC_DEBUG
-		printk("ECC Errors corrected: %x\n", nb_errors);
-#endif
-		if (nb_errors < 0) {
-			/* We return error, but have actually done the
-			   read. Not that this can be told to user-space, via
-			   sys_read(), but at least MTD-aware stuff can know
-			   about it by checking *retlen */
-#ifdef ECC_DEBUG
-			printk("%s(%d): Millennium Plus ECC error (from=0x%x:\n",
-				__FILE__, __LINE__, (int)from);
-			printk("        syndrome= %*phC\n", 6, syndrome);
-			printk("        eccbuf= %*phC\n", 6, eccbuf);
-#endif
-				ret = -EIO;
-		}
-	}
-
-#ifdef PSYCHO_DEBUG
-	printk("ECC DATA at %lx: %*ph\n", (long)from, 6, eccbuf);
-#endif
-	/* disable the ECC engine */
-	WriteDOC(DOC_ECC_DIS, docptr , Mplus_ECCConf);
-
-	/* Disable flash internally */
-	WriteDOC(0, docptr, Mplus_FlashSelect);
-
-	return ret;
-}
-
-static int doc_write(struct mtd_info *mtd, loff_t to, size_t len,
-		     size_t *retlen, const u_char *buf)
-{
-	int i, before, ret = 0;
-	loff_t fto;
-	volatile char dummy;
-	char eccbuf[6];
-	struct DiskOnChip *this = mtd->priv;
-	void __iomem * docptr = this->virtadr;
-	struct Nand *mychip = &this->chips[to >> (this->chipshift)];
-
-	/* Don't allow writes which aren't exactly one block (512 bytes) */
-	if ((to & 0x1ff) || (len != 0x200))
-		return -EINVAL;
-
-	/* Determine position of OOB flags, before or after data */
-	before = (this->interleave && (to & 0x200));
-
-	DoC_CheckASIC(docptr);
-
-	/* Find the chip which is to be used and select it */
-	if (this->curfloor != mychip->floor) {
-		DoC_SelectFloor(docptr, mychip->floor);
-		DoC_SelectChip(docptr, mychip->chip);
-	} else if (this->curchip != mychip->chip) {
-		DoC_SelectChip(docptr, mychip->chip);
-	}
-	this->curfloor = mychip->floor;
-	this->curchip = mychip->chip;
-
-	/* Millennium Plus bus cycle sequence as per figure 2, section 2.4 */
-	WriteDOC(DOC_FLASH_CE, docptr, Mplus_FlashSelect);
-
-	/* Reset the chip, see Software Requirement 11.4 item 1. */
-	DoC_Command(docptr, NAND_CMD_RESET, 0);
-	DoC_WaitReady(docptr);
-
-	/* Set device to appropriate plane of flash */
-	fto = to;
-	WriteDOC(DoC_GetDataOffset(mtd, &fto), docptr, Mplus_FlashCmd);
-
-	/* On interleaved devices the flags for 2nd half 512 are before data */
-	if (before)
-		fto -= 2;
-
-	/* issue the Serial Data In command to initial the Page Program process */
-	DoC_Command(docptr, NAND_CMD_SEQIN, 0x00);
-	DoC_Address(this, 3, fto, 0x00, 0x00);
-
-	/* Disable the ECC engine */
-	WriteDOC(DOC_ECC_RESET, docptr, Mplus_ECCConf);
-
-	if (before) {
-		/* Write the block status BLOCK_USED (0x5555) */
-		WriteDOC(0x55, docptr, Mil_CDSN_IO);
-		WriteDOC(0x55, docptr, Mil_CDSN_IO);
-	}
-
-	/* init the ECC engine, see Reed-Solomon EDC/ECC 11.1 .*/
-	WriteDOC(DOC_ECC_EN | DOC_ECC_RW, docptr, Mplus_ECCConf);
-
-	MemWriteDOC(docptr, (unsigned char *) buf, len);
-
-	/* Write ECC data to flash, the ECC info is generated by
-	   the DiskOnChip ECC logic see Reed-Solomon EDC/ECC 11.1 */
-	DoC_Delay(docptr, 3);
-
-	/* Read the ECC data through the DiskOnChip ECC logic */
-	for (i = 0; i < 6; i++)
-		eccbuf[i] = ReadDOC(docptr, Mplus_ECCSyndrome0 + i);
-
-	/* disable the ECC engine */
-	WriteDOC(DOC_ECC_DIS, docptr, Mplus_ECCConf);
-
-	/* Write the ECC data to flash */
-	MemWriteDOC(docptr, eccbuf, 6);
-
-	if (!before) {
-		/* Write the block status BLOCK_USED (0x5555) */
-		WriteDOC(0x55, docptr, Mil_CDSN_IO+6);
-		WriteDOC(0x55, docptr, Mil_CDSN_IO+7);
-	}
-
-#ifdef PSYCHO_DEBUG
-	printk("OOB data at %lx is %2.2X %2.2X %2.2X %2.2X %2.2X %2.2X\n",
-	       (long) to, eccbuf[0], eccbuf[1], eccbuf[2], eccbuf[3],
-	       eccbuf[4], eccbuf[5]);
-#endif
-
-	WriteDOC(0x00, docptr, Mplus_WritePipeTerm);
-	WriteDOC(0x00, docptr, Mplus_WritePipeTerm);
-
-	/* Commit the Page Program command and wait for ready
-	   see Software Requirement 11.4 item 1.*/
-	DoC_Command(docptr, NAND_CMD_PAGEPROG, 0x00);
-	DoC_WaitReady(docptr);
-
-	/* Read the status of the flash device through CDSN IO register
-	   see Software Requirement 11.4 item 5.*/
-	DoC_Command(docptr, NAND_CMD_STATUS, 0);
-	dummy = ReadDOC(docptr, Mplus_ReadPipeInit);
-	dummy = ReadDOC(docptr, Mplus_ReadPipeInit);
-	DoC_Delay(docptr, 2);
-	if ((dummy = ReadDOC(docptr, Mplus_LastDataRead)) & 1) {
-		printk("MTD: Error 0x%x programming at 0x%x\n", dummy, (int)to);
-		/* Error in programming
-		   FIXME: implement Bad Block Replacement (in nftl.c ??) */
-		ret = -EIO;
-	}
-	dummy = ReadDOC(docptr, Mplus_LastDataRead);
-
-	/* Disable flash internally */
-	WriteDOC(0, docptr, Mplus_FlashSelect);
-
-	/* Let the caller know we completed it */
-	*retlen = len;
-
-	return ret;
-}
-
-static int doc_read_oob(struct mtd_info *mtd, loff_t ofs,
-			struct mtd_oob_ops *ops)
-{
-	loff_t fofs, base;
-	struct DiskOnChip *this = mtd->priv;
-	void __iomem * docptr = this->virtadr;
-	struct Nand *mychip = &this->chips[ofs >> this->chipshift];
-	size_t i, size, got, want;
-	uint8_t *buf = ops->oobbuf;
-	size_t len = ops->len;
-
-	BUG_ON(ops->mode != MTD_OPS_PLACE_OOB);
-
-	ofs += ops->ooboffs;
-
-	DoC_CheckASIC(docptr);
-
-	/* Find the chip which is to be used and select it */
-	if (this->curfloor != mychip->floor) {
-		DoC_SelectFloor(docptr, mychip->floor);
-		DoC_SelectChip(docptr, mychip->chip);
-	} else if (this->curchip != mychip->chip) {
-		DoC_SelectChip(docptr, mychip->chip);
-	}
-	this->curfloor = mychip->floor;
-	this->curchip = mychip->chip;
-
-	/* Millennium Plus bus cycle sequence as per figure 2, section 2.4 */
-	WriteDOC((DOC_FLASH_CE | DOC_FLASH_WP), docptr, Mplus_FlashSelect);
-
-	/* disable the ECC engine */
-	WriteDOC(DOC_ECC_RESET, docptr, Mplus_ECCConf);
-	DoC_WaitReady(docptr);
-
-	/* Maximum of 16 bytes in the OOB region, so limit read to that */
-	if (len > 16)
-		len = 16;
-	got = 0;
-	want = len;
-
-	for (i = 0; ((i < 3) && (want > 0)); i++) {
-		/* Figure out which region we are accessing... */
-		fofs = ofs;
-		base = ofs & 0xf;
-		if (!this->interleave) {
-			DoC_Command(docptr, NAND_CMD_READOOB, 0);
-			size = 16 - base;
-		} else if (base < 6) {
-			DoC_Command(docptr, DoC_GetECCOffset(mtd, &fofs), 0);
-			size = 6 - base;
-		} else if (base < 8) {
-			DoC_Command(docptr, DoC_GetFlagsOffset(mtd, &fofs), 0);
-			size = 8 - base;
-		} else {
-			DoC_Command(docptr, DoC_GetHdrOffset(mtd, &fofs), 0);
-			size = 16 - base;
-		}
-		if (size > want)
-			size = want;
-
-		/* Issue read command */
-		DoC_Address(this, 3, fofs, 0, 0x00);
-		WriteDOC(0, docptr, Mplus_FlashControl);
-		DoC_WaitReady(docptr);
-
-		ReadDOC(docptr, Mplus_ReadPipeInit);
-		ReadDOC(docptr, Mplus_ReadPipeInit);
-		MemReadDOC(docptr, &buf[got], size - 2);
-		buf[got + size - 2] = ReadDOC(docptr, Mplus_LastDataRead);
-		buf[got + size - 1] = ReadDOC(docptr, Mplus_LastDataRead);
-
-		ofs += size;
-		got += size;
-		want -= size;
-	}
-
-	/* Disable flash internally */
-	WriteDOC(0, docptr, Mplus_FlashSelect);
-
-	ops->retlen = len;
-	return 0;
-}
-
-static int doc_write_oob(struct mtd_info *mtd, loff_t ofs,
-			 struct mtd_oob_ops *ops)
-{
-	volatile char dummy;
-	loff_t fofs, base;
-	struct DiskOnChip *this = mtd->priv;
-	void __iomem * docptr = this->virtadr;
-	struct Nand *mychip = &this->chips[ofs >> this->chipshift];
-	size_t i, size, got, want;
-	int ret = 0;
-	uint8_t *buf = ops->oobbuf;
-	size_t len = ops->len;
-
-	BUG_ON(ops->mode != MTD_OPS_PLACE_OOB);
-
-	ofs += ops->ooboffs;
-
-	DoC_CheckASIC(docptr);
-
-	/* Find the chip which is to be used and select it */
-	if (this->curfloor != mychip->floor) {
-		DoC_SelectFloor(docptr, mychip->floor);
-		DoC_SelectChip(docptr, mychip->chip);
-	} else if (this->curchip != mychip->chip) {
-		DoC_SelectChip(docptr, mychip->chip);
-	}
-	this->curfloor = mychip->floor;
-	this->curchip = mychip->chip;
-
-	/* Millennium Plus bus cycle sequence as per figure 2, section 2.4 */
-	WriteDOC(DOC_FLASH_CE, docptr, Mplus_FlashSelect);
-
-
-	/* Maximum of 16 bytes in the OOB region, so limit write to that */
-	if (len > 16)
-		len = 16;
-	got = 0;
-	want = len;
-
-	for (i = 0; ((i < 3) && (want > 0)); i++) {
-		/* Reset the chip, see Software Requirement 11.4 item 1. */
-		DoC_Command(docptr, NAND_CMD_RESET, 0);
-		DoC_WaitReady(docptr);
-
-		/* Figure out which region we are accessing... */
-		fofs = ofs;
-		base = ofs & 0x0f;
-		if (!this->interleave) {
-			WriteDOC(NAND_CMD_READOOB, docptr, Mplus_FlashCmd);
-			size = 16 - base;
-		} else if (base < 6) {
-			WriteDOC(DoC_GetECCOffset(mtd, &fofs), docptr, Mplus_FlashCmd);
-			size = 6 - base;
-		} else if (base < 8) {
-			WriteDOC(DoC_GetFlagsOffset(mtd, &fofs), docptr, Mplus_FlashCmd);
-			size = 8 - base;
-		} else {
-			WriteDOC(DoC_GetHdrOffset(mtd, &fofs), docptr, Mplus_FlashCmd);
-			size = 16 - base;
-		}
-		if (size > want)
-			size = want;
-
-		/* Issue the Serial Data In command to initial the Page Program process */
-		DoC_Command(docptr, NAND_CMD_SEQIN, 0x00);
-		DoC_Address(this, 3, fofs, 0, 0x00);
-
-		/* Disable the ECC engine */
-		WriteDOC(DOC_ECC_RESET, docptr, Mplus_ECCConf);
-
-		/* Write the data via the internal pipeline through CDSN IO
-		   register, see Pipelined Write Operations 11.2 */
-		MemWriteDOC(docptr, (unsigned char *) &buf[got], size);
-		WriteDOC(0x00, docptr, Mplus_WritePipeTerm);
-		WriteDOC(0x00, docptr, Mplus_WritePipeTerm);
-
-		/* Commit the Page Program command and wait for ready
-	 	   see Software Requirement 11.4 item 1.*/
-		DoC_Command(docptr, NAND_CMD_PAGEPROG, 0x00);
-		DoC_WaitReady(docptr);
-
-		/* Read the status of the flash device through CDSN IO register
-		   see Software Requirement 11.4 item 5.*/
-		DoC_Command(docptr, NAND_CMD_STATUS, 0x00);
-		dummy = ReadDOC(docptr, Mplus_ReadPipeInit);
-		dummy = ReadDOC(docptr, Mplus_ReadPipeInit);
-		DoC_Delay(docptr, 2);
-		if ((dummy = ReadDOC(docptr, Mplus_LastDataRead)) & 1) {
-			printk("MTD: Error 0x%x programming oob at 0x%x\n",
-				dummy, (int)ofs);
-			/* FIXME: implement Bad Block Replacement */
-			ops->retlen = 0;
-			ret = -EIO;
-		}
-		dummy = ReadDOC(docptr, Mplus_LastDataRead);
-
-		ofs += size;
-		got += size;
-		want -= size;
-	}
-
-	/* Disable flash internally */
-	WriteDOC(0, docptr, Mplus_FlashSelect);
-
-	ops->retlen = len;
-	return ret;
-}
-
-int doc_erase(struct mtd_info *mtd, struct erase_info *instr)
-{
-	volatile char dummy;
-	struct DiskOnChip *this = mtd->priv;
-	__u32 ofs = instr->addr;
-	__u32 len = instr->len;
-	void __iomem * docptr = this->virtadr;
-	struct Nand *mychip = &this->chips[ofs >> this->chipshift];
-
-	DoC_CheckASIC(docptr);
-
-	if (len != mtd->erasesize)
-		printk(KERN_WARNING "MTD: Erase not right size (%x != %x)n",
-		       len, mtd->erasesize);
-
-	/* Find the chip which is to be used and select it */
-	if (this->curfloor != mychip->floor) {
-		DoC_SelectFloor(docptr, mychip->floor);
-		DoC_SelectChip(docptr, mychip->chip);
-	} else if (this->curchip != mychip->chip) {
-		DoC_SelectChip(docptr, mychip->chip);
-	}
-	this->curfloor = mychip->floor;
-	this->curchip = mychip->chip;
-
-	instr->state = MTD_ERASE_PENDING;
-
-	/* Millennium Plus bus cycle sequence as per figure 2, section 2.4 */
-	WriteDOC(DOC_FLASH_CE, docptr, Mplus_FlashSelect);
-
-	DoC_Command(docptr, NAND_CMD_RESET, 0x00);
-	DoC_WaitReady(docptr);
-
-	DoC_Command(docptr, NAND_CMD_ERASE1, 0);
-	DoC_Address(this, 2, ofs, 0, 0x00);
-	DoC_Command(docptr, NAND_CMD_ERASE2, 0);
-	DoC_WaitReady(docptr);
-	instr->state = MTD_ERASING;
-
-	/* Read the status of the flash device through CDSN IO register
-	   see Software Requirement 11.4 item 5. */
-	DoC_Command(docptr, NAND_CMD_STATUS, 0);
-	dummy = ReadDOC(docptr, Mplus_ReadPipeInit);
-	dummy = ReadDOC(docptr, Mplus_ReadPipeInit);
-	if ((dummy = ReadDOC(docptr, Mplus_LastDataRead)) & 1) {
-		printk("MTD: Error 0x%x erasing at 0x%x\n", dummy, ofs);
-		/* FIXME: implement Bad Block Replacement (in nftl.c ??) */
-		instr->state = MTD_ERASE_FAILED;
-	} else {
-		instr->state = MTD_ERASE_DONE;
-	}
-	dummy = ReadDOC(docptr, Mplus_LastDataRead);
-
-	/* Disable flash internally */
-	WriteDOC(0, docptr, Mplus_FlashSelect);
-
-	mtd_erase_callback(instr);
-
-	return 0;
-}
-
-/****************************************************************************
- *
- * Module stuff
- *
- ****************************************************************************/
-
-static void __exit cleanup_doc2001plus(void)
-{
-	struct mtd_info *mtd;
-	struct DiskOnChip *this;
-
-	while ((mtd=docmilpluslist)) {
-		this = mtd->priv;
-		docmilpluslist = this->nextdoc;
-
-		mtd_device_unregister(mtd);
-
-		iounmap(this->virtadr);
-		kfree(this->chips);
-		kfree(mtd);
-	}
-}
-
-module_exit(cleanup_doc2001plus);
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Greg Ungerer <gerg@snapgear.com> et al.");
-MODULE_DESCRIPTION("Driver for DiskOnChip Millennium Plus");
diff --git a/drivers/mtd/devices/docecc.c b/drivers/mtd/devices/docecc.c
deleted file mode 100644
index 4a1c39b6f37d..000000000000
--- a/drivers/mtd/devices/docecc.c
+++ /dev/null
@@ -1,521 +0,0 @@
-/*
- * ECC algorithm for M-systems disk on chip. We use the excellent Reed
- * Solmon code of Phil Karn (karn@ka9q.ampr.org) available under the
- * GNU GPL License. The rest is simply to convert the disk on chip
- * syndrome into a standard syndome.
- *
- * Author: Fabrice Bellard (fabrice.bellard@netgem.com)
- * Copyright (C) 2000 Netgem S.A.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <asm/errno.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
-#include <linux/delay.h>
-#include <linux/slab.h>
-#include <linux/init.h>
-#include <linux/types.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/doc2000.h>
-
-#define DEBUG_ECC 0
-/* need to undef it (from asm/termbits.h) */
-#undef B0
-
-#define MM 10 /* Symbol size in bits */
-#define KK (1023-4) /* Number of data symbols per block */
-#define B0 510 /* First root of generator polynomial, alpha form */
-#define PRIM 1 /* power of alpha used to generate roots of generator poly */
-#define	NN ((1 << MM) - 1)
-
-typedef unsigned short dtype;
-
-/* 1+x^3+x^10 */
-static const int Pp[MM+1] = { 1, 0, 0, 1, 0, 0, 0, 0, 0, 0, 1 };
-
-/* This defines the type used to store an element of the Galois Field
- * used by the code. Make sure this is something larger than a char if
- * if anything larger than GF(256) is used.
- *
- * Note: unsigned char will work up to GF(256) but int seems to run
- * faster on the Pentium.
- */
-typedef int gf;
-
-/* No legal value in index form represents zero, so
- * we need a special value for this purpose
- */
-#define A0	(NN)
-
-/* Compute x % NN, where NN is 2**MM - 1,
- * without a slow divide
- */
-static inline gf
-modnn(int x)
-{
-  while (x >= NN) {
-    x -= NN;
-    x = (x >> MM) + (x & NN);
-  }
-  return x;
-}
-
-#define	CLEAR(a,n) {\
-int ci;\
-for(ci=(n)-1;ci >=0;ci--)\
-(a)[ci] = 0;\
-}
-
-#define	COPY(a,b,n) {\
-int ci;\
-for(ci=(n)-1;ci >=0;ci--)\
-(a)[ci] = (b)[ci];\
-}
-
-#define	COPYDOWN(a,b,n) {\
-int ci;\
-for(ci=(n)-1;ci >=0;ci--)\
-(a)[ci] = (b)[ci];\
-}
-
-#define Ldec 1
-
-/* generate GF(2**m) from the irreducible polynomial p(X) in Pp[0]..Pp[m]
-   lookup tables:  index->polynomial form   alpha_to[] contains j=alpha**i;
-                   polynomial form -> index form  index_of[j=alpha**i] = i
-   alpha=2 is the primitive element of GF(2**m)
-   HARI's COMMENT: (4/13/94) alpha_to[] can be used as follows:
-        Let @ represent the primitive element commonly called "alpha" that
-   is the root of the primitive polynomial p(x). Then in GF(2^m), for any
-   0 <= i <= 2^m-2,
-        @^i = a(0) + a(1) @ + a(2) @^2 + ... + a(m-1) @^(m-1)
-   where the binary vector (a(0),a(1),a(2),...,a(m-1)) is the representation
-   of the integer "alpha_to[i]" with a(0) being the LSB and a(m-1) the MSB. Thus for
-   example the polynomial representation of @^5 would be given by the binary
-   representation of the integer "alpha_to[5]".
-                   Similarly, index_of[] can be used as follows:
-        As above, let @ represent the primitive element of GF(2^m) that is
-   the root of the primitive polynomial p(x). In order to find the power
-   of @ (alpha) that has the polynomial representation
-        a(0) + a(1) @ + a(2) @^2 + ... + a(m-1) @^(m-1)
-   we consider the integer "i" whose binary representation with a(0) being LSB
-   and a(m-1) MSB is (a(0),a(1),...,a(m-1)) and locate the entry
-   "index_of[i]". Now, @^index_of[i] is that element whose polynomial
-    representation is (a(0),a(1),a(2),...,a(m-1)).
-   NOTE:
-        The element alpha_to[2^m-1] = 0 always signifying that the
-   representation of "@^infinity" = 0 is (0,0,0,...,0).
-        Similarly, the element index_of[0] = A0 always signifying
-   that the power of alpha which has the polynomial representation
-   (0,0,...,0) is "infinity".
-
-*/
-
-static void
-generate_gf(dtype Alpha_to[NN + 1], dtype Index_of[NN + 1])
-{
-  register int i, mask;
-
-  mask = 1;
-  Alpha_to[MM] = 0;
-  for (i = 0; i < MM; i++) {
-    Alpha_to[i] = mask;
-    Index_of[Alpha_to[i]] = i;
-    /* If Pp[i] == 1 then, term @^i occurs in poly-repr of @^MM */
-    if (Pp[i] != 0)
-      Alpha_to[MM] ^= mask;	/* Bit-wise EXOR operation */
-    mask <<= 1;	/* single left-shift */
-  }
-  Index_of[Alpha_to[MM]] = MM;
-  /*
-   * Have obtained poly-repr of @^MM. Poly-repr of @^(i+1) is given by
-   * poly-repr of @^i shifted left one-bit and accounting for any @^MM
-   * term that may occur when poly-repr of @^i is shifted.
-   */
-  mask >>= 1;
-  for (i = MM + 1; i < NN; i++) {
-    if (Alpha_to[i - 1] >= mask)
-      Alpha_to[i] = Alpha_to[MM] ^ ((Alpha_to[i - 1] ^ mask) << 1);
-    else
-      Alpha_to[i] = Alpha_to[i - 1] << 1;
-    Index_of[Alpha_to[i]] = i;
-  }
-  Index_of[0] = A0;
-  Alpha_to[NN] = 0;
-}
-
-/*
- * Performs ERRORS+ERASURES decoding of RS codes. bb[] is the content
- * of the feedback shift register after having processed the data and
- * the ECC.
- *
- * Return number of symbols corrected, or -1 if codeword is illegal
- * or uncorrectable. If eras_pos is non-null, the detected error locations
- * are written back. NOTE! This array must be at least NN-KK elements long.
- * The corrected data are written in eras_val[]. They must be xor with the data
- * to retrieve the correct data : data[erase_pos[i]] ^= erase_val[i] .
- *
- * First "no_eras" erasures are declared by the calling program. Then, the
- * maximum # of errors correctable is t_after_eras = floor((NN-KK-no_eras)/2).
- * If the number of channel errors is not greater than "t_after_eras" the
- * transmitted codeword will be recovered. Details of algorithm can be found
- * in R. Blahut's "Theory ... of Error-Correcting Codes".
-
- * Warning: the eras_pos[] array must not contain duplicate entries; decoder failure
- * will result. The decoder *could* check for this condition, but it would involve
- * extra time on every decoding operation.
- * */
-static int
-eras_dec_rs(dtype Alpha_to[NN + 1], dtype Index_of[NN + 1],
-            gf bb[NN - KK + 1], gf eras_val[NN-KK], int eras_pos[NN-KK],
-            int no_eras)
-{
-  int deg_lambda, el, deg_omega;
-  int i, j, r,k;
-  gf u,q,tmp,num1,num2,den,discr_r;
-  gf lambda[NN-KK + 1], s[NN-KK + 1];	/* Err+Eras Locator poly
-					 * and syndrome poly */
-  gf b[NN-KK + 1], t[NN-KK + 1], omega[NN-KK + 1];
-  gf root[NN-KK], reg[NN-KK + 1], loc[NN-KK];
-  int syn_error, count;
-
-  syn_error = 0;
-  for(i=0;i<NN-KK;i++)
-      syn_error |= bb[i];
-
-  if (!syn_error) {
-    /* if remainder is zero, data[] is a codeword and there are no
-     * errors to correct. So return data[] unmodified
-     */
-    count = 0;
-    goto finish;
-  }
-
-  for(i=1;i<=NN-KK;i++){
-    s[i] = bb[0];
-  }
-  for(j=1;j<NN-KK;j++){
-    if(bb[j] == 0)
-      continue;
-    tmp = Index_of[bb[j]];
-
-    for(i=1;i<=NN-KK;i++)
-      s[i] ^= Alpha_to[modnn(tmp + (B0+i-1)*PRIM*j)];
-  }
-
-  /* undo the feedback register implicit multiplication and convert
-     syndromes to index form */
-
-  for(i=1;i<=NN-KK;i++) {
-      tmp = Index_of[s[i]];
-      if (tmp != A0)
-          tmp = modnn(tmp + 2 * KK * (B0+i-1)*PRIM);
-      s[i] = tmp;
-  }
-
-  CLEAR(&lambda[1],NN-KK);
-  lambda[0] = 1;
-
-  if (no_eras > 0) {
-    /* Init lambda to be the erasure locator polynomial */
-    lambda[1] = Alpha_to[modnn(PRIM * eras_pos[0])];
-    for (i = 1; i < no_eras; i++) {
-      u = modnn(PRIM*eras_pos[i]);
-      for (j = i+1; j > 0; j--) {
-	tmp = Index_of[lambda[j - 1]];
-	if(tmp != A0)
-	  lambda[j] ^= Alpha_to[modnn(u + tmp)];
-      }
-    }
-#if DEBUG_ECC >= 1
-    /* Test code that verifies the erasure locator polynomial just constructed
-       Needed only for decoder debugging. */
-
-    /* find roots of the erasure location polynomial */
-    for(i=1;i<=no_eras;i++)
-      reg[i] = Index_of[lambda[i]];
-    count = 0;
-    for (i = 1,k=NN-Ldec; i <= NN; i++,k = modnn(NN+k-Ldec)) {
-      q = 1;
-      for (j = 1; j <= no_eras; j++)
-	if (reg[j] != A0) {
-	  reg[j] = modnn(reg[j] + j);
-	  q ^= Alpha_to[reg[j]];
-	}
-      if (q != 0)
-	continue;
-      /* store root and error location number indices */
-      root[count] = i;
-      loc[count] = k;
-      count++;
-    }
-    if (count != no_eras) {
-      printf("\n lambda(x) is WRONG\n");
-      count = -1;
-      goto finish;
-    }
-#if DEBUG_ECC >= 2
-    printf("\n Erasure positions as determined by roots of Eras Loc Poly:\n");
-    for (i = 0; i < count; i++)
-      printf("%d ", loc[i]);
-    printf("\n");
-#endif
-#endif
-  }
-  for(i=0;i<NN-KK+1;i++)
-    b[i] = Index_of[lambda[i]];
-
-  /*
-   * Begin Berlekamp-Massey algorithm to determine error+erasure
-   * locator polynomial
-   */
-  r = no_eras;
-  el = no_eras;
-  while (++r <= NN-KK) {	/* r is the step number */
-    /* Compute discrepancy at the r-th step in poly-form */
-    discr_r = 0;
-    for (i = 0; i < r; i++){
-      if ((lambda[i] != 0) && (s[r - i] != A0)) {
-	discr_r ^= Alpha_to[modnn(Index_of[lambda[i]] + s[r - i])];
-      }
-    }
-    discr_r = Index_of[discr_r];	/* Index form */
-    if (discr_r == A0) {
-      /* 2 lines below: B(x) <-- x*B(x) */
-      COPYDOWN(&b[1],b,NN-KK);
-      b[0] = A0;
-    } else {
-      /* 7 lines below: T(x) <-- lambda(x) - discr_r*x*b(x) */
-      t[0] = lambda[0];
-      for (i = 0 ; i < NN-KK; i++) {
-	if(b[i] != A0)
-	  t[i+1] = lambda[i+1] ^ Alpha_to[modnn(discr_r + b[i])];
-	else
-	  t[i+1] = lambda[i+1];
-      }
-      if (2 * el <= r + no_eras - 1) {
-	el = r + no_eras - el;
-	/*
-	 * 2 lines below: B(x) <-- inv(discr_r) *
-	 * lambda(x)
-	 */
-	for (i = 0; i <= NN-KK; i++)
-	  b[i] = (lambda[i] == 0) ? A0 : modnn(Index_of[lambda[i]] - discr_r + NN);
-      } else {
-	/* 2 lines below: B(x) <-- x*B(x) */
-	COPYDOWN(&b[1],b,NN-KK);
-	b[0] = A0;
-      }
-      COPY(lambda,t,NN-KK+1);
-    }
-  }
-
-  /* Convert lambda to index form and compute deg(lambda(x)) */
-  deg_lambda = 0;
-  for(i=0;i<NN-KK+1;i++){
-    lambda[i] = Index_of[lambda[i]];
-    if(lambda[i] != A0)
-      deg_lambda = i;
-  }
-  /*
-   * Find roots of the error+erasure locator polynomial by Chien
-   * Search
-   */
-  COPY(&reg[1],&lambda[1],NN-KK);
-  count = 0;		/* Number of roots of lambda(x) */
-  for (i = 1,k=NN-Ldec; i <= NN; i++,k = modnn(NN+k-Ldec)) {
-    q = 1;
-    for (j = deg_lambda; j > 0; j--){
-      if (reg[j] != A0) {
-	reg[j] = modnn(reg[j] + j);
-	q ^= Alpha_to[reg[j]];
-      }
-    }
-    if (q != 0)
-      continue;
-    /* store root (index-form) and error location number */
-    root[count] = i;
-    loc[count] = k;
-    /* If we've already found max possible roots,
-     * abort the search to save time
-     */
-    if(++count == deg_lambda)
-      break;
-  }
-  if (deg_lambda != count) {
-    /*
-     * deg(lambda) unequal to number of roots => uncorrectable
-     * error detected
-     */
-    count = -1;
-    goto finish;
-  }
-  /*
-   * Compute err+eras evaluator poly omega(x) = s(x)*lambda(x) (modulo
-   * x**(NN-KK)). in index form. Also find deg(omega).
-   */
-  deg_omega = 0;
-  for (i = 0; i < NN-KK;i++){
-    tmp = 0;
-    j = (deg_lambda < i) ? deg_lambda : i;
-    for(;j >= 0; j--){
-      if ((s[i + 1 - j] != A0) && (lambda[j] != A0))
-	tmp ^= Alpha_to[modnn(s[i + 1 - j] + lambda[j])];
-    }
-    if(tmp != 0)
-      deg_omega = i;
-    omega[i] = Index_of[tmp];
-  }
-  omega[NN-KK] = A0;
-
-  /*
-   * Compute error values in poly-form. num1 = omega(inv(X(l))), num2 =
-   * inv(X(l))**(B0-1) and den = lambda_pr(inv(X(l))) all in poly-form
-   */
-  for (j = count-1; j >=0; j--) {
-    num1 = 0;
-    for (i = deg_omega; i >= 0; i--) {
-      if (omega[i] != A0)
-	num1  ^= Alpha_to[modnn(omega[i] + i * root[j])];
-    }
-    num2 = Alpha_to[modnn(root[j] * (B0 - 1) + NN)];
-    den = 0;
-
-    /* lambda[i+1] for i even is the formal derivative lambda_pr of lambda[i] */
-    for (i = min(deg_lambda,NN-KK-1) & ~1; i >= 0; i -=2) {
-      if(lambda[i+1] != A0)
-	den ^= Alpha_to[modnn(lambda[i+1] + i * root[j])];
-    }
-    if (den == 0) {
-#if DEBUG_ECC >= 1
-      printf("\n ERROR: denominator = 0\n");
-#endif
-      /* Convert to dual- basis */
-      count = -1;
-      goto finish;
-    }
-    /* Apply error to data */
-    if (num1 != 0) {
-        eras_val[j] = Alpha_to[modnn(Index_of[num1] + Index_of[num2] + NN - Index_of[den])];
-    } else {
-        eras_val[j] = 0;
-    }
-  }
- finish:
-  for(i=0;i<count;i++)
-      eras_pos[i] = loc[i];
-  return count;
-}
-
-/***************************************************************************/
-/* The DOC specific code begins here */
-
-#define SECTOR_SIZE 512
-/* The sector bytes are packed into NB_DATA MM bits words */
-#define NB_DATA (((SECTOR_SIZE + 1) * 8 + 6) / MM)
-
-/*
- * Correct the errors in 'sector[]' by using 'ecc1[]' which is the
- * content of the feedback shift register applyied to the sector and
- * the ECC. Return the number of errors corrected (and correct them in
- * sector), or -1 if error
- */
-int doc_decode_ecc(unsigned char sector[SECTOR_SIZE], unsigned char ecc1[6])
-{
-    int parity, i, nb_errors;
-    gf bb[NN - KK + 1];
-    gf error_val[NN-KK];
-    int error_pos[NN-KK], pos, bitpos, index, val;
-    dtype *Alpha_to, *Index_of;
-
-    /* init log and exp tables here to save memory. However, it is slower */
-    Alpha_to = kmalloc((NN + 1) * sizeof(dtype), GFP_KERNEL);
-    if (!Alpha_to)
-        return -1;
-
-    Index_of = kmalloc((NN + 1) * sizeof(dtype), GFP_KERNEL);
-    if (!Index_of) {
-        kfree(Alpha_to);
-        return -1;
-    }
-
-    generate_gf(Alpha_to, Index_of);
-
-    parity = ecc1[1];
-
-    bb[0] =  (ecc1[4] & 0xff) | ((ecc1[5] & 0x03) << 8);
-    bb[1] = ((ecc1[5] & 0xfc) >> 2) | ((ecc1[2] & 0x0f) << 6);
-    bb[2] = ((ecc1[2] & 0xf0) >> 4) | ((ecc1[3] & 0x3f) << 4);
-    bb[3] = ((ecc1[3] & 0xc0) >> 6) | ((ecc1[0] & 0xff) << 2);
-
-    nb_errors = eras_dec_rs(Alpha_to, Index_of, bb,
-                            error_val, error_pos, 0);
-    if (nb_errors <= 0)
-        goto the_end;
-
-    /* correct the errors */
-    for(i=0;i<nb_errors;i++) {
-        pos = error_pos[i];
-        if (pos >= NB_DATA && pos < KK) {
-            nb_errors = -1;
-            goto the_end;
-        }
-        if (pos < NB_DATA) {
-            /* extract bit position (MSB first) */
-            pos = 10 * (NB_DATA - 1 - pos) - 6;
-            /* now correct the following 10 bits. At most two bytes
-               can be modified since pos is even */
-            index = (pos >> 3) ^ 1;
-            bitpos = pos & 7;
-            if ((index >= 0 && index < SECTOR_SIZE) ||
-                index == (SECTOR_SIZE + 1)) {
-                val = error_val[i] >> (2 + bitpos);
-                parity ^= val;
-                if (index < SECTOR_SIZE)
-                    sector[index] ^= val;
-            }
-            index = ((pos >> 3) + 1) ^ 1;
-            bitpos = (bitpos + 10) & 7;
-            if (bitpos == 0)
-                bitpos = 8;
-            if ((index >= 0 && index < SECTOR_SIZE) ||
-                index == (SECTOR_SIZE + 1)) {
-                val = error_val[i] << (8 - bitpos);
-                parity ^= val;
-                if (index < SECTOR_SIZE)
-                    sector[index] ^= val;
-            }
-        }
-    }
-
-    /* use parity to test extra errors */
-    if ((parity & 0xff) != 0)
-        nb_errors = -1;
-
- the_end:
-    kfree(Alpha_to);
-    kfree(Index_of);
-    return nb_errors;
-}
-
-EXPORT_SYMBOL_GPL(doc_decode_ecc);
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Fabrice Bellard <fabrice.bellard@netgem.com>");
-MODULE_DESCRIPTION("ECC code for correcting errors detected by DiskOnChip 2000 and Millennium ECC hardware");
diff --git a/drivers/mtd/devices/docprobe.c b/drivers/mtd/devices/docprobe.c
deleted file mode 100644
index 88b3fd3e18a7..000000000000
--- a/drivers/mtd/devices/docprobe.c
+++ /dev/null
@@ -1,325 +0,0 @@
-
-/* Linux driver for Disk-On-Chip devices			*/
-/* Probe routines common to all DoC devices			*/
-/* (C) 1999 Machine Vision Holdings, Inc.			*/
-/* (C) 1999-2003 David Woodhouse <dwmw2@infradead.org>		*/
-
-
-/* DOC_PASSIVE_PROBE:
-   In order to ensure that the BIOS checksum is correct at boot time, and
-   hence that the onboard BIOS extension gets executed, the DiskOnChip
-   goes into reset mode when it is read sequentially: all registers
-   return 0xff until the chip is woken up again by writing to the
-   DOCControl register.
-
-   Unfortunately, this means that the probe for the DiskOnChip is unsafe,
-   because one of the first things it does is write to where it thinks
-   the DOCControl register should be - which may well be shared memory
-   for another device. I've had machines which lock up when this is
-   attempted. Hence the possibility to do a passive probe, which will fail
-   to detect a chip in reset mode, but is at least guaranteed not to lock
-   the machine.
-
-   If you have this problem, uncomment the following line:
-#define DOC_PASSIVE_PROBE
-*/
-
-
-/* DOC_SINGLE_DRIVER:
-   Millennium driver has been merged into DOC2000 driver.
-
-   The old Millennium-only driver has been retained just in case there
-   are problems with the new code. If the combined driver doesn't work
-   for you, you can try the old one by undefining DOC_SINGLE_DRIVER
-   below and also enabling it in your configuration. If this fixes the
-   problems, please send a report to the MTD mailing list at
-   <linux-mtd@lists.infradead.org>.
-*/
-#define DOC_SINGLE_DRIVER
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <asm/errno.h>
-#include <asm/io.h>
-#include <linux/delay.h>
-#include <linux/slab.h>
-#include <linux/init.h>
-#include <linux/types.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/nand.h>
-#include <linux/mtd/doc2000.h>
-
-
-static unsigned long doc_config_location = CONFIG_MTD_DOCPROBE_ADDRESS;
-module_param(doc_config_location, ulong, 0);
-MODULE_PARM_DESC(doc_config_location, "Physical memory address at which to probe for DiskOnChip");
-
-static unsigned long __initdata doc_locations[] = {
-#if defined (__alpha__) || defined(__i386__) || defined(__x86_64__)
-#ifdef CONFIG_MTD_DOCPROBE_HIGH
-	0xfffc8000, 0xfffca000, 0xfffcc000, 0xfffce000,
-	0xfffd0000, 0xfffd2000, 0xfffd4000, 0xfffd6000,
-	0xfffd8000, 0xfffda000, 0xfffdc000, 0xfffde000,
-	0xfffe0000, 0xfffe2000, 0xfffe4000, 0xfffe6000,
-	0xfffe8000, 0xfffea000, 0xfffec000, 0xfffee000,
-#else /*  CONFIG_MTD_DOCPROBE_HIGH */
-	0xc8000, 0xca000, 0xcc000, 0xce000,
-	0xd0000, 0xd2000, 0xd4000, 0xd6000,
-	0xd8000, 0xda000, 0xdc000, 0xde000,
-	0xe0000, 0xe2000, 0xe4000, 0xe6000,
-	0xe8000, 0xea000, 0xec000, 0xee000,
-#endif /*  CONFIG_MTD_DOCPROBE_HIGH */
-#endif
-	0xffffffff };
-
-/* doccheck: Probe a given memory window to see if there's a DiskOnChip present */
-
-static inline int __init doccheck(void __iomem *potential, unsigned long physadr)
-{
-	void __iomem *window=potential;
-	unsigned char tmp, tmpb, tmpc, ChipID;
-#ifndef DOC_PASSIVE_PROBE
-	unsigned char tmp2;
-#endif
-
-	/* Routine copied from the Linux DOC driver */
-
-#ifdef CONFIG_MTD_DOCPROBE_55AA
-	/* Check for 0x55 0xAA signature at beginning of window,
-	   this is no longer true once we remove the IPL (for Millennium */
-	if (ReadDOC(window, Sig1) != 0x55 || ReadDOC(window, Sig2) != 0xaa)
-		return 0;
-#endif /* CONFIG_MTD_DOCPROBE_55AA */
-
-#ifndef DOC_PASSIVE_PROBE
-	/* It's not possible to cleanly detect the DiskOnChip - the
-	 * bootup procedure will put the device into reset mode, and
-	 * it's not possible to talk to it without actually writing
-	 * to the DOCControl register. So we store the current contents
-	 * of the DOCControl register's location, in case we later decide
-	 * that it's not a DiskOnChip, and want to put it back how we
-	 * found it.
-	 */
-	tmp2 = ReadDOC(window, DOCControl);
-
-	/* Reset the DiskOnChip ASIC */
-	WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_RESET,
-		 window, DOCControl);
-	WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_RESET,
-		 window, DOCControl);
-
-	/* Enable the DiskOnChip ASIC */
-	WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_NORMAL,
-		 window, DOCControl);
-	WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_NORMAL,
-		 window, DOCControl);
-#endif /* !DOC_PASSIVE_PROBE */
-
-	/* We need to read the ChipID register four times. For some
-	   newer DiskOnChip 2000 units, the first three reads will
-	   return the DiskOnChip Millennium ident. Don't ask. */
-	ChipID = ReadDOC(window, ChipID);
-
-	switch (ChipID) {
-	case DOC_ChipID_Doc2k:
-		/* Check the TOGGLE bit in the ECC register */
-		tmp  = ReadDOC(window, 2k_ECCStatus) & DOC_TOGGLE_BIT;
-		tmpb = ReadDOC(window, 2k_ECCStatus) & DOC_TOGGLE_BIT;
-		tmpc = ReadDOC(window, 2k_ECCStatus) & DOC_TOGGLE_BIT;
-		if (tmp != tmpb && tmp == tmpc)
-				return ChipID;
-		break;
-
-	case DOC_ChipID_DocMil:
-		/* Check for the new 2000 with Millennium ASIC */
-		ReadDOC(window, ChipID);
-		ReadDOC(window, ChipID);
-		if (ReadDOC(window, ChipID) != DOC_ChipID_DocMil)
-			ChipID = DOC_ChipID_Doc2kTSOP;
-
-		/* Check the TOGGLE bit in the ECC register */
-		tmp  = ReadDOC(window, ECCConf) & DOC_TOGGLE_BIT;
-		tmpb = ReadDOC(window, ECCConf) & DOC_TOGGLE_BIT;
-		tmpc = ReadDOC(window, ECCConf) & DOC_TOGGLE_BIT;
-		if (tmp != tmpb && tmp == tmpc)
-				return ChipID;
-		break;
-
-	case DOC_ChipID_DocMilPlus16:
-	case DOC_ChipID_DocMilPlus32:
-	case 0:
-		/* Possible Millennium+, need to do more checks */
-#ifndef DOC_PASSIVE_PROBE
-		/* Possibly release from power down mode */
-		for (tmp = 0; (tmp < 4); tmp++)
-			ReadDOC(window, Mplus_Power);
-
-		/* Reset the DiskOnChip ASIC */
-		tmp = DOC_MODE_RESET | DOC_MODE_MDWREN | DOC_MODE_RST_LAT |
-			DOC_MODE_BDECT;
-		WriteDOC(tmp, window, Mplus_DOCControl);
-		WriteDOC(~tmp, window, Mplus_CtrlConfirm);
-
-		mdelay(1);
-		/* Enable the DiskOnChip ASIC */
-		tmp = DOC_MODE_NORMAL | DOC_MODE_MDWREN | DOC_MODE_RST_LAT |
-			DOC_MODE_BDECT;
-		WriteDOC(tmp, window, Mplus_DOCControl);
-		WriteDOC(~tmp, window, Mplus_CtrlConfirm);
-		mdelay(1);
-#endif /* !DOC_PASSIVE_PROBE */
-
-		ChipID = ReadDOC(window, ChipID);
-
-		switch (ChipID) {
-		case DOC_ChipID_DocMilPlus16:
-		case DOC_ChipID_DocMilPlus32:
-			/* Check the TOGGLE bit in the toggle register */
-			tmp  = ReadDOC(window, Mplus_Toggle) & DOC_TOGGLE_BIT;
-			tmpb = ReadDOC(window, Mplus_Toggle) & DOC_TOGGLE_BIT;
-			tmpc = ReadDOC(window, Mplus_Toggle) & DOC_TOGGLE_BIT;
-			if (tmp != tmpb && tmp == tmpc)
-					return ChipID;
-		default:
-			break;
-		}
-		/* FALL TRHU */
-
-	default:
-
-#ifdef CONFIG_MTD_DOCPROBE_55AA
-		printk(KERN_DEBUG "Possible DiskOnChip with unknown ChipID %2.2X found at 0x%lx\n",
-		       ChipID, physadr);
-#endif
-#ifndef DOC_PASSIVE_PROBE
-		/* Put back the contents of the DOCControl register, in case it's not
-		 * actually a DiskOnChip.
-		 */
-		WriteDOC(tmp2, window, DOCControl);
-#endif
-		return 0;
-	}
-
-	printk(KERN_WARNING "DiskOnChip failed TOGGLE test, dropping.\n");
-
-#ifndef DOC_PASSIVE_PROBE
-	/* Put back the contents of the DOCControl register: it's not a DiskOnChip */
-	WriteDOC(tmp2, window, DOCControl);
-#endif
-	return 0;
-}
-
-static int docfound;
-
-extern void DoC2k_init(struct mtd_info *);
-extern void DoCMil_init(struct mtd_info *);
-extern void DoCMilPlus_init(struct mtd_info *);
-
-static void __init DoC_Probe(unsigned long physadr)
-{
-	void __iomem *docptr;
-	struct DiskOnChip *this;
-	struct mtd_info *mtd;
-	int ChipID;
-	char namebuf[15];
-	char *name = namebuf;
-	void (*initroutine)(struct mtd_info *) = NULL;
-
-	docptr = ioremap(physadr, DOC_IOREMAP_LEN);
-
-	if (!docptr)
-		return;
-
-	if ((ChipID = doccheck(docptr, physadr))) {
-		if (ChipID == DOC_ChipID_Doc2kTSOP) {
-			/* Remove this at your own peril. The hardware driver works but nothing prevents you from erasing bad blocks */
-			printk(KERN_NOTICE "Refusing to drive DiskOnChip 2000 TSOP until Bad Block Table is correctly supported by INFTL\n");
-			iounmap(docptr);
-			return;
-		}
-		docfound = 1;
-		mtd = kzalloc(sizeof(struct DiskOnChip) + sizeof(struct mtd_info), GFP_KERNEL);
-		if (!mtd) {
-			printk(KERN_WARNING "Cannot allocate memory for data structures. Dropping.\n");
-			iounmap(docptr);
-			return;
-		}
-
-		this = (struct DiskOnChip *)(&mtd[1]);
-		mtd->priv = this;
-		this->virtadr = docptr;
-		this->physadr = physadr;
-		this->ChipID = ChipID;
-		sprintf(namebuf, "with ChipID %2.2X", ChipID);
-
-		switch(ChipID) {
-		case DOC_ChipID_Doc2kTSOP:
-			name="2000 TSOP";
-			initroutine = symbol_request(DoC2k_init);
-			break;
-
-		case DOC_ChipID_Doc2k:
-			name="2000";
-			initroutine = symbol_request(DoC2k_init);
-			break;
-
-		case DOC_ChipID_DocMil:
-			name="Millennium";
-#ifdef DOC_SINGLE_DRIVER
-			initroutine = symbol_request(DoC2k_init);
-#else
-			initroutine = symbol_request(DoCMil_init);
-#endif /* DOC_SINGLE_DRIVER */
-			break;
-
-		case DOC_ChipID_DocMilPlus16:
-		case DOC_ChipID_DocMilPlus32:
-			name="MillenniumPlus";
-			initroutine = symbol_request(DoCMilPlus_init);
-			break;
-		}
-
-		if (initroutine) {
-			(*initroutine)(mtd);
-			symbol_put_addr(initroutine);
-			return;
-		}
-		printk(KERN_NOTICE "Cannot find driver for DiskOnChip %s at 0x%lX\n", name, physadr);
-		kfree(mtd);
-	}
-	iounmap(docptr);
-}
-
-
-/****************************************************************************
- *
- * Module stuff
- *
- ****************************************************************************/
-
-static int __init init_doc(void)
-{
-	int i;
-
-	if (doc_config_location) {
-		printk(KERN_INFO "Using configured DiskOnChip probe address 0x%lx\n", doc_config_location);
-		DoC_Probe(doc_config_location);
-	} else {
-		for (i=0; (doc_locations[i] != 0xffffffff); i++) {
-			DoC_Probe(doc_locations[i]);
-		}
-	}
-	/* No banner message any more. Print a message if no DiskOnChip
-	   found, so the user knows we at least tried. */
-	if (!docfound)
-		printk(KERN_INFO "No recognised DiskOnChip devices found\n");
-	return -EAGAIN;
-}
-
-module_init(init_doc);
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("David Woodhouse <dwmw2@infradead.org>");
-MODULE_DESCRIPTION("Probe code for DiskOnChip 2000 and Millennium devices");
-