seeq: Move the SEEQ drivers

Move the drivers that use SEEQ chipset into drivers/net/ethernet/seeq
and make the necessary Kconfig and Makefile changes.

CC: Russell King <linux@arm.linux.org.uk>
CC: Hamish Coleman <hamish@zot.apana.org.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

1 files changed, 0 insertions, 752 deletions

diff --git a/drivers/net/seeq8005.c b/drivers/net/seeq8005.c
deleted file mode 100644
index d2fce98f557f..000000000000
--- a/drivers/net/seeq8005.c
+++ /dev/null
@@ -1,752 +0,0 @@
-/* seeq8005.c: A network driver for linux. */
-/*
-	Based on skeleton.c,
-	Written 1993-94 by Donald Becker.
-	See the skeleton.c file for further copyright information.
-
-	This software may be used and distributed according to the terms
-	of the GNU General Public License, incorporated herein by reference.
-
-	The author may be reached as hamish@zot.apana.org.au
-
-	This file is a network device driver for the SEEQ 8005 chipset and
-	the Linux operating system.
-
-*/
-
-static const char version[] =
-	"seeq8005.c:v1.00 8/07/95 Hamish Coleman (hamish@zot.apana.org.au)\n";
-
-/*
-  Sources:
-  	SEEQ 8005 databook
-
-  Version history:
-  	1.00	Public release. cosmetic changes (no warnings now)
-  	0.68	Turning per- packet,interrupt debug messages off - testing for release.
-  	0.67	timing problems/bad buffer reads seem to be fixed now
-  	0.63	*!@$ protocol=eth_type_trans -- now packets flow
-  	0.56	Send working
-  	0.48	Receive working
-*/
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/fcntl.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
-#include <linux/in.h>
-#include <linux/string.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/errno.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/skbuff.h>
-#include <linux/bitops.h>
-#include <linux/jiffies.h>
-
-#include <asm/system.h>
-#include <asm/io.h>
-#include <asm/dma.h>
-
-#include "seeq8005.h"
-
-/* First, a few definitions that the brave might change. */
-/* A zero-terminated list of I/O addresses to be probed. */
-static unsigned int seeq8005_portlist[] __initdata =
-   { 0x300, 0x320, 0x340, 0x360, 0};
-
-/* use 0 for production, 1 for verification, >2 for debug */
-#ifndef NET_DEBUG
-#define NET_DEBUG 1
-#endif
-static unsigned int net_debug = NET_DEBUG;
-
-/* Information that need to be kept for each board. */
-struct net_local {
-	unsigned short receive_ptr;		/* What address in packet memory do we expect a recv_pkt_header? */
-	long open_time;				/* Useless example local info. */
-};
-
-/* The station (ethernet) address prefix, used for IDing the board. */
-#define SA_ADDR0 0x00
-#define SA_ADDR1 0x80
-#define SA_ADDR2 0x4b
-
-/* Index to functions, as function prototypes. */
-
-static int seeq8005_probe1(struct net_device *dev, int ioaddr);
-static int seeq8005_open(struct net_device *dev);
-static void seeq8005_timeout(struct net_device *dev);
-static netdev_tx_t seeq8005_send_packet(struct sk_buff *skb,
-					struct net_device *dev);
-static irqreturn_t seeq8005_interrupt(int irq, void *dev_id);
-static void seeq8005_rx(struct net_device *dev);
-static int seeq8005_close(struct net_device *dev);
-static void set_multicast_list(struct net_device *dev);
-
-/* Example routines you must write ;->. */
-#define tx_done(dev)	(inw(SEEQ_STATUS) & SEEQSTAT_TX_ON)
-static void hardware_send_packet(struct net_device *dev, char *buf, int length);
-extern void seeq8005_init(struct net_device *dev, int startp);
-static inline void wait_for_buffer(struct net_device *dev);
-
-
-/* Check for a network adaptor of this type, and return '0' iff one exists.
-   If dev->base_addr == 0, probe all likely locations.
-   If dev->base_addr == 1, always return failure.
-   */
-
-static int io = 0x320;
-static int irq = 10;
-
-struct net_device * __init seeq8005_probe(int unit)
-{
-	struct net_device *dev = alloc_etherdev(sizeof(struct net_local));
-	unsigned *port;
-	int err = 0;
-
-	if (!dev)
-		return ERR_PTR(-ENODEV);
-
-	if (unit >= 0) {
-		sprintf(dev->name, "eth%d", unit);
-		netdev_boot_setup_check(dev);
-		io = dev->base_addr;
-		irq = dev->irq;
-	}
-
-	if (io > 0x1ff) {	/* Check a single specified location. */
-		err = seeq8005_probe1(dev, io);
-	} else if (io != 0) {	/* Don't probe at all. */
-		err = -ENXIO;
-	} else {
-		for (port = seeq8005_portlist; *port; port++) {
-			if (seeq8005_probe1(dev, *port) == 0)
-				break;
-		}
-		if (!*port)
-			err = -ENODEV;
-	}
-	if (err)
-		goto out;
-	err = register_netdev(dev);
-	if (err)
-		goto out1;
-	return dev;
-out1:
-	release_region(dev->base_addr, SEEQ8005_IO_EXTENT);
-out:
-	free_netdev(dev);
-	return ERR_PTR(err);
-}
-
-static const struct net_device_ops seeq8005_netdev_ops = {
-	.ndo_open		= seeq8005_open,
-	.ndo_stop		= seeq8005_close,
-	.ndo_start_xmit 	= seeq8005_send_packet,
-	.ndo_tx_timeout		= seeq8005_timeout,
-	.ndo_set_multicast_list = set_multicast_list,
-	.ndo_change_mtu		= eth_change_mtu,
-	.ndo_set_mac_address 	= eth_mac_addr,
-	.ndo_validate_addr	= eth_validate_addr,
-};
-
-/* This is the real probe routine.  Linux has a history of friendly device
-   probes on the ISA bus.  A good device probes avoids doing writes, and
-   verifies that the correct device exists and functions.  */
-
-static int __init seeq8005_probe1(struct net_device *dev, int ioaddr)
-{
-	static unsigned version_printed;
-	int i,j;
-	unsigned char SA_prom[32];
-	int old_cfg1;
-	int old_cfg2;
-	int old_stat;
-	int old_dmaar;
-	int old_rear;
-	int retval;
-
-	if (!request_region(ioaddr, SEEQ8005_IO_EXTENT, "seeq8005"))
-		return -ENODEV;
-
-	if (net_debug>1)
-		printk("seeq8005: probing at 0x%x\n",ioaddr);
-
-	old_stat = inw(SEEQ_STATUS);					/* read status register */
-	if (old_stat == 0xffff) {
-		retval = -ENODEV;
-		goto out;						/* assume that 0xffff == no device */
-	}
-	if ( (old_stat & 0x1800) != 0x1800 ) {				/* assume that unused bits are 1, as my manual says */
-		if (net_debug>1) {
-			printk("seeq8005: reserved stat bits != 0x1800\n");
-			printk("          == 0x%04x\n",old_stat);
-		}
-	 	retval = -ENODEV;
-		goto out;
-	}
-
-	old_rear = inw(SEEQ_REA);
-	if (old_rear == 0xffff) {
-		outw(0,SEEQ_REA);
-		if (inw(SEEQ_REA) == 0xffff) {				/* assume that 0xffff == no device */
-			retval = -ENODEV;
-			goto out;
-		}
-	} else if ((old_rear & 0xff00) != 0xff00) {			/* assume that unused bits are 1 */
-		if (net_debug>1) {
-			printk("seeq8005: unused rear bits != 0xff00\n");
-			printk("          == 0x%04x\n",old_rear);
-		}
-		retval = -ENODEV;
-		goto out;
-	}
-
-	old_cfg2 = inw(SEEQ_CFG2);					/* read CFG2 register */
-	old_cfg1 = inw(SEEQ_CFG1);
-	old_dmaar = inw(SEEQ_DMAAR);
-
-	if (net_debug>4) {
-		printk("seeq8005: stat = 0x%04x\n",old_stat);
-		printk("seeq8005: cfg1 = 0x%04x\n",old_cfg1);
-		printk("seeq8005: cfg2 = 0x%04x\n",old_cfg2);
-		printk("seeq8005: raer = 0x%04x\n",old_rear);
-		printk("seeq8005: dmaar= 0x%04x\n",old_dmaar);
-	}
-
-	outw( SEEQCMD_FIFO_WRITE | SEEQCMD_SET_ALL_OFF, SEEQ_CMD);	/* setup for reading PROM */
-	outw( 0, SEEQ_DMAAR);						/* set starting PROM address */
-	outw( SEEQCFG1_BUFFER_PROM, SEEQ_CFG1);				/* set buffer to look at PROM */
-
-
-	j=0;
-	for(i=0; i <32; i++) {
-		j+= SA_prom[i] = inw(SEEQ_BUFFER) & 0xff;
-	}
-
-#if 0
-	/* untested because I only have the one card */
-	if ( (j&0xff) != 0 ) {						/* checksum appears to be 8bit = 0 */
-		if (net_debug>1) {					/* check this before deciding that we have a card */
-			printk("seeq8005: prom sum error\n");
-		}
-		outw( old_stat, SEEQ_STATUS);
-		outw( old_dmaar, SEEQ_DMAAR);
-		outw( old_cfg1, SEEQ_CFG1);
-		retval = -ENODEV;
-		goto out;
-	}
-#endif
-
-	outw( SEEQCFG2_RESET, SEEQ_CFG2);				/* reset the card */
-	udelay(5);
-	outw( SEEQCMD_SET_ALL_OFF, SEEQ_CMD);
-
-	if (net_debug) {
-		printk("seeq8005: prom sum = 0x%08x\n",j);
-		for(j=0; j<32; j+=16) {
-			printk("seeq8005: prom %02x: ",j);
-			for(i=0;i<16;i++) {
-				printk("%02x ",SA_prom[j|i]);
-			}
-			printk(" ");
-			for(i=0;i<16;i++) {
-				if ((SA_prom[j|i]>31)&&(SA_prom[j|i]<127)) {
-					printk("%c", SA_prom[j|i]);
-				} else {
-					printk(" ");
-				}
-			}
-			printk("\n");
-		}
-	}
-
-#if 0
-	/*
-	 * testing the packet buffer memory doesn't work yet
-	 * but all other buffer accesses do
-	 *			- fixing is not a priority
-	 */
-	if (net_debug>1) {					/* test packet buffer memory */
-		printk("seeq8005: testing packet buffer ... ");
-		outw( SEEQCFG1_BUFFER_BUFFER, SEEQ_CFG1);
-		outw( SEEQCMD_FIFO_WRITE | SEEQCMD_SET_ALL_OFF, SEEQ_CMD);
-		outw( 0 , SEEQ_DMAAR);
-		for(i=0;i<32768;i++) {
-			outw(0x5a5a, SEEQ_BUFFER);
-		}
-		j=jiffies+HZ;
-		while ( ((inw(SEEQ_STATUS) & SEEQSTAT_FIFO_EMPTY) != SEEQSTAT_FIFO_EMPTY) && time_before(jiffies, j) )
-			mb();
-		outw( 0 , SEEQ_DMAAR);
-		while ( ((inw(SEEQ_STATUS) & SEEQSTAT_WINDOW_INT) != SEEQSTAT_WINDOW_INT) && time_before(jiffies, j+HZ))
-			mb();
-		if ( (inw(SEEQ_STATUS) & SEEQSTAT_WINDOW_INT) == SEEQSTAT_WINDOW_INT)
-			outw( SEEQCMD_WINDOW_INT_ACK | (inw(SEEQ_STATUS)& SEEQCMD_INT_MASK), SEEQ_CMD);
-		outw( SEEQCMD_FIFO_READ | SEEQCMD_SET_ALL_OFF, SEEQ_CMD);
-		j=0;
-		for(i=0;i<32768;i++) {
-			if (inw(SEEQ_BUFFER) != 0x5a5a)
-				j++;
-		}
-		if (j) {
-			printk("%i\n",j);
-		} else {
-			printk("ok.\n");
-		}
-	}
-#endif
-
-	if (net_debug  &&  version_printed++ == 0)
-		printk(version);
-
-	printk("%s: %s found at %#3x, ", dev->name, "seeq8005", ioaddr);
-
-	/* Fill in the 'dev' fields. */
-	dev->base_addr = ioaddr;
-	dev->irq = irq;
-
-	/* Retrieve and print the ethernet address. */
-	for (i = 0; i < 6; i++)
-		dev->dev_addr[i] = SA_prom[i+6];
-	printk("%pM", dev->dev_addr);
-
-	if (dev->irq == 0xff)
-		;			/* Do nothing: a user-level program will set it. */
-	else if (dev->irq < 2) {	/* "Auto-IRQ" */
-		unsigned long cookie = probe_irq_on();
-
-		outw( SEEQCMD_RX_INT_EN | SEEQCMD_SET_RX_ON | SEEQCMD_SET_RX_OFF, SEEQ_CMD );
-
-		dev->irq = probe_irq_off(cookie);
-
-		if (net_debug >= 2)
-			printk(" autoirq is %d\n", dev->irq);
-	} else if (dev->irq == 2)
-	  /* Fixup for users that don't know that IRQ 2 is really IRQ 9,
-	   * or don't know which one to set.
-	   */
-	  dev->irq = 9;
-
-#if 0
-	{
-		 int irqval = request_irq(dev->irq, seeq8005_interrupt, 0, "seeq8005", dev);
-		 if (irqval) {
-			 printk ("%s: unable to get IRQ %d (irqval=%d).\n", dev->name,
-					 dev->irq, irqval);
-			 retval = -EAGAIN;
-			 goto out;
-		 }
-	}
-#endif
-	dev->netdev_ops = &seeq8005_netdev_ops;
-	dev->watchdog_timeo	= HZ/20;
-	dev->flags &= ~IFF_MULTICAST;
-
-	return 0;
-out:
-	release_region(ioaddr, SEEQ8005_IO_EXTENT);
-	return retval;
-}
-
-
-/* Open/initialize the board.  This is called (in the current kernel)
-   sometime after booting when the 'ifconfig' program is run.
-
-   This routine should set everything up anew at each open, even
-   registers that "should" only need to be set once at boot, so that
-   there is non-reboot way to recover if something goes wrong.
-   */
-static int seeq8005_open(struct net_device *dev)
-{
-	struct net_local *lp = netdev_priv(dev);
-
-	{
-		 int irqval = request_irq(dev->irq, seeq8005_interrupt, 0, "seeq8005", dev);
-		 if (irqval) {
-			 printk ("%s: unable to get IRQ %d (irqval=%d).\n", dev->name,
-					 dev->irq, irqval);
-			 return -EAGAIN;
-		 }
-	}
-
-	/* Reset the hardware here.  Don't forget to set the station address. */
-	seeq8005_init(dev, 1);
-
-	lp->open_time = jiffies;
-
-	netif_start_queue(dev);
-	return 0;
-}
-
-static void seeq8005_timeout(struct net_device *dev)
-{
-	int ioaddr = dev->base_addr;
-	printk(KERN_WARNING "%s: transmit timed out, %s?\n", dev->name,
-		   tx_done(dev) ? "IRQ conflict" : "network cable problem");
-	/* Try to restart the adaptor. */
-	seeq8005_init(dev, 1);
-	dev->trans_start = jiffies; /* prevent tx timeout */
-	netif_wake_queue(dev);
-}
-
-static netdev_tx_t seeq8005_send_packet(struct sk_buff *skb,
-					struct net_device *dev)
-{
-	short length = skb->len;
-	unsigned char *buf;
-
-	if (length < ETH_ZLEN) {
-		if (skb_padto(skb, ETH_ZLEN))
-			return NETDEV_TX_OK;
-		length = ETH_ZLEN;
-	}
-	buf = skb->data;
-
-	/* Block a timer-based transmit from overlapping */
-	netif_stop_queue(dev);
-
-	hardware_send_packet(dev, buf, length);
-	dev->stats.tx_bytes += length;
-	dev_kfree_skb (skb);
-	/* You might need to clean up and record Tx statistics here. */
-
-	return NETDEV_TX_OK;
-}
-
-/*
- * wait_for_buffer
- *
- * This routine waits for the SEEQ chip to assert that the FIFO is ready
- * by checking for a window interrupt, and then clearing it. This has to
- * occur in the interrupt handler!
- */
-inline void wait_for_buffer(struct net_device * dev)
-{
-	int ioaddr = dev->base_addr;
-	unsigned long tmp;
-	int status;
-
-	tmp = jiffies + HZ;
-	while ( ( ((status=inw(SEEQ_STATUS)) & SEEQSTAT_WINDOW_INT) != SEEQSTAT_WINDOW_INT) && time_before(jiffies, tmp))
-		cpu_relax();
-
-	if ( (status & SEEQSTAT_WINDOW_INT) == SEEQSTAT_WINDOW_INT)
-		outw( SEEQCMD_WINDOW_INT_ACK | (status & SEEQCMD_INT_MASK), SEEQ_CMD);
-}
-
-/* The typical workload of the driver:
-   Handle the network interface interrupts. */
-static irqreturn_t seeq8005_interrupt(int irq, void *dev_id)
-{
-	struct net_device *dev = dev_id;
-	struct net_local *lp;
-	int ioaddr, status, boguscount = 0;
-	int handled = 0;
-
-	ioaddr = dev->base_addr;
-	lp = netdev_priv(dev);
-
-	status = inw(SEEQ_STATUS);
-	do {
-		if (net_debug >2) {
-			printk("%s: int, status=0x%04x\n",dev->name,status);
-		}
-
-		if (status & SEEQSTAT_WINDOW_INT) {
-			handled = 1;
-			outw( SEEQCMD_WINDOW_INT_ACK | (status & SEEQCMD_INT_MASK), SEEQ_CMD);
-			if (net_debug) {
-				printk("%s: window int!\n",dev->name);
-			}
-		}
-		if (status & SEEQSTAT_TX_INT) {
-			handled = 1;
-			outw( SEEQCMD_TX_INT_ACK | (status & SEEQCMD_INT_MASK), SEEQ_CMD);
-			dev->stats.tx_packets++;
-			netif_wake_queue(dev);	/* Inform upper layers. */
-		}
-		if (status & SEEQSTAT_RX_INT) {
-			handled = 1;
-			/* Got a packet(s). */
-			seeq8005_rx(dev);
-		}
-		status = inw(SEEQ_STATUS);
-	} while ( (++boguscount < 10) && (status & SEEQSTAT_ANY_INT)) ;
-
-	if(net_debug>2) {
-		printk("%s: eoi\n",dev->name);
-	}
-	return IRQ_RETVAL(handled);
-}
-
-/* We have a good packet(s), get it/them out of the buffers. */
-static void seeq8005_rx(struct net_device *dev)
-{
-	struct net_local *lp = netdev_priv(dev);
-	int boguscount = 10;
-	int pkt_hdr;
-	int ioaddr = dev->base_addr;
-
-	do {
-		int next_packet;
-		int pkt_len;
-		int i;
-		int status;
-
-		status = inw(SEEQ_STATUS);
-	  	outw( lp->receive_ptr, SEEQ_DMAAR);
-		outw(SEEQCMD_FIFO_READ | SEEQCMD_RX_INT_ACK | (status & SEEQCMD_INT_MASK), SEEQ_CMD);
-	  	wait_for_buffer(dev);
-	  	next_packet = ntohs(inw(SEEQ_BUFFER));
-	  	pkt_hdr = inw(SEEQ_BUFFER);
-
-		if (net_debug>2) {
-			printk("%s: 0x%04x recv next=0x%04x, hdr=0x%04x\n",dev->name,lp->receive_ptr,next_packet,pkt_hdr);
-		}
-
-		if ((next_packet == 0) || ((pkt_hdr & SEEQPKTH_CHAIN)==0)) {	/* Read all the frames? */
-			return;							/* Done for now */
-		}
-
-		if ((pkt_hdr & SEEQPKTS_DONE)==0)
-			break;
-
-		if (next_packet < lp->receive_ptr) {
-			pkt_len = (next_packet + 0x10000 - ((DEFAULT_TEA+1)<<8)) - lp->receive_ptr - 4;
-		} else {
-			pkt_len = next_packet - lp->receive_ptr - 4;
-		}
-
-		if (next_packet < ((DEFAULT_TEA+1)<<8)) {			/* is the next_packet address sane? */
-			printk("%s: recv packet ring corrupt, resetting board\n",dev->name);
-			seeq8005_init(dev,1);
-			return;
-		}
-
-		lp->receive_ptr = next_packet;
-
-		if (net_debug>2) {
-			printk("%s: recv len=0x%04x\n",dev->name,pkt_len);
-		}
-
-		if (pkt_hdr & SEEQPKTS_ANY_ERROR) {				/* There was an error. */
-			dev->stats.rx_errors++;
-			if (pkt_hdr & SEEQPKTS_SHORT) dev->stats.rx_frame_errors++;
-			if (pkt_hdr & SEEQPKTS_DRIB) dev->stats.rx_frame_errors++;
-			if (pkt_hdr & SEEQPKTS_OVERSIZE) dev->stats.rx_over_errors++;
-			if (pkt_hdr & SEEQPKTS_CRC_ERR) dev->stats.rx_crc_errors++;
-			/* skip over this packet */
-			outw( SEEQCMD_FIFO_WRITE | SEEQCMD_DMA_INT_ACK | (status & SEEQCMD_INT_MASK), SEEQ_CMD);
-			outw( (lp->receive_ptr & 0xff00)>>8, SEEQ_REA);
-		} else {
-			/* Malloc up new buffer. */
-			struct sk_buff *skb;
-			unsigned char *buf;
-
-			skb = dev_alloc_skb(pkt_len);
-			if (skb == NULL) {
-				printk("%s: Memory squeeze, dropping packet.\n", dev->name);
-				dev->stats.rx_dropped++;
-				break;
-			}
-			skb_reserve(skb, 2);	/* align data on 16 byte */
-			buf = skb_put(skb,pkt_len);
-
-			insw(SEEQ_BUFFER, buf, (pkt_len + 1) >> 1);
-
-			if (net_debug>2) {
-				char * p = buf;
-				printk("%s: recv ",dev->name);
-				for(i=0;i<14;i++) {
-					printk("%02x ",*(p++)&0xff);
-				}
-				printk("\n");
-			}
-
-			skb->protocol=eth_type_trans(skb,dev);
-			netif_rx(skb);
-			dev->stats.rx_packets++;
-			dev->stats.rx_bytes += pkt_len;
-		}
-	} while ((--boguscount) && (pkt_hdr & SEEQPKTH_CHAIN));
-
-	/* If any worth-while packets have been received, netif_rx()
-	   has done a mark_bh(NET_BH) for us and will work on them
-	   when we get to the bottom-half routine. */
-}
-
-/* The inverse routine to net_open(). */
-static int seeq8005_close(struct net_device *dev)
-{
-	struct net_local *lp = netdev_priv(dev);
-	int ioaddr = dev->base_addr;
-
-	lp->open_time = 0;
-
-	netif_stop_queue(dev);
-
-	/* Flush the Tx and disable Rx here. */
-	outw( SEEQCMD_SET_ALL_OFF, SEEQ_CMD);
-
-	free_irq(dev->irq, dev);
-
-	/* Update the statistics here. */
-
-	return 0;
-
-}
-
-/* Set or clear the multicast filter for this adaptor.
-   num_addrs == -1	Promiscuous mode, receive all packets
-   num_addrs == 0	Normal mode, clear multicast list
-   num_addrs > 0	Multicast mode, receive normal and MC packets, and do
-			best-effort filtering.
- */
-static void set_multicast_list(struct net_device *dev)
-{
-/*
- * I _could_ do up to 6 addresses here, but won't (yet?)
- */
-
-#if 0
-	int ioaddr = dev->base_addr;
-/*
- * hmm, not even sure if my matching works _anyway_ - seem to be receiving
- * _everything_ . . .
- */
-
-	if (num_addrs) {			/* Enable promiscuous mode */
-		outw( (inw(SEEQ_CFG1) & ~SEEQCFG1_MATCH_MASK)| SEEQCFG1_MATCH_ALL,  SEEQ_CFG1);
-		dev->flags|=IFF_PROMISC;
-	} else {				/* Disable promiscuous mode, use normal mode */
-		outw( (inw(SEEQ_CFG1) & ~SEEQCFG1_MATCH_MASK)| SEEQCFG1_MATCH_BROAD, SEEQ_CFG1);
-	}
-#endif
-}
-
-void seeq8005_init(struct net_device *dev, int startp)
-{
-	struct net_local *lp = netdev_priv(dev);
-	int ioaddr = dev->base_addr;
-	int i;
-
-	outw(SEEQCFG2_RESET, SEEQ_CFG2);	/* reset device */
-	udelay(5);
-
-	outw( SEEQCMD_FIFO_WRITE | SEEQCMD_SET_ALL_OFF, SEEQ_CMD);
-	outw( 0, SEEQ_DMAAR);			/* load start address into both low and high byte */
-/*	wait_for_buffer(dev); */		/* I think that you only need a wait for memory buffer */
-	outw( SEEQCFG1_BUFFER_MAC0, SEEQ_CFG1);
-
-	for(i=0;i<6;i++) {			/* set Station address */
-		outb(dev->dev_addr[i], SEEQ_BUFFER);
-		udelay(2);
-	}
-
-	outw( SEEQCFG1_BUFFER_TEA, SEEQ_CFG1);	/* set xmit end area pointer to 16K */
-	outb( DEFAULT_TEA, SEEQ_BUFFER);	/* this gives us 16K of send buffer and 48K of recv buffer */
-
-	lp->receive_ptr = (DEFAULT_TEA+1)<<8;	/* so we can find our packet_header */
-	outw( lp->receive_ptr, SEEQ_RPR);	/* Receive Pointer Register is set to recv buffer memory */
-
-	outw( 0x00ff, SEEQ_REA);		/* Receive Area End */
-
-	if (net_debug>4) {
-		printk("%s: SA0 = ",dev->name);
-
-		outw( SEEQCMD_FIFO_READ | SEEQCMD_SET_ALL_OFF, SEEQ_CMD);
-		outw( 0, SEEQ_DMAAR);
-		outw( SEEQCFG1_BUFFER_MAC0, SEEQ_CFG1);
-
-		for(i=0;i<6;i++) {
-			printk("%02x ",inb(SEEQ_BUFFER));
-		}
-		printk("\n");
-	}
-
-	outw( SEEQCFG1_MAC0_EN | SEEQCFG1_MATCH_BROAD | SEEQCFG1_BUFFER_BUFFER, SEEQ_CFG1);
-	outw( SEEQCFG2_AUTO_REA | SEEQCFG2_CTRLO, SEEQ_CFG2);
-	outw( SEEQCMD_SET_RX_ON | SEEQCMD_TX_INT_EN | SEEQCMD_RX_INT_EN, SEEQ_CMD);
-
-	if (net_debug>4) {
-		int old_cfg1;
-		old_cfg1 = inw(SEEQ_CFG1);
-		printk("%s: stat = 0x%04x\n",dev->name,inw(SEEQ_STATUS));
-		printk("%s: cfg1 = 0x%04x\n",dev->name,old_cfg1);
-		printk("%s: cfg2 = 0x%04x\n",dev->name,inw(SEEQ_CFG2));
-		printk("%s: raer = 0x%04x\n",dev->name,inw(SEEQ_REA));
-		printk("%s: dmaar= 0x%04x\n",dev->name,inw(SEEQ_DMAAR));
-
-	}
-}
-
-
-static void hardware_send_packet(struct net_device * dev, char *buf, int length)
-{
-	int ioaddr = dev->base_addr;
-	int status = inw(SEEQ_STATUS);
-	int transmit_ptr = 0;
-	unsigned long tmp;
-
-	if (net_debug>4) {
-		printk("%s: send 0x%04x\n",dev->name,length);
-	}
-
-	/* Set FIFO to writemode and set packet-buffer address */
-	outw( SEEQCMD_FIFO_WRITE | (status & SEEQCMD_INT_MASK), SEEQ_CMD);
-	outw( transmit_ptr, SEEQ_DMAAR);
-
-	/* output SEEQ Packet header barfage */
-	outw( htons(length + 4), SEEQ_BUFFER);
-	outw( SEEQPKTH_XMIT | SEEQPKTH_DATA_FOLLOWS | SEEQPKTH_XMIT_INT_EN, SEEQ_BUFFER );
-
-	/* blat the buffer */
-	outsw( SEEQ_BUFFER, buf, (length +1) >> 1);
-	/* paranoia !! */
-	outw( 0, SEEQ_BUFFER);
-	outw( 0, SEEQ_BUFFER);
-
-	/* set address of start of transmit chain */
-	outw( transmit_ptr, SEEQ_TPR);
-
-	/* drain FIFO */
-	tmp = jiffies;
-	while ( (((status=inw(SEEQ_STATUS)) & SEEQSTAT_FIFO_EMPTY) == 0) && time_before(jiffies, tmp + HZ))
-		mb();
-
-	/* doit ! */
-	outw( SEEQCMD_WINDOW_INT_ACK | SEEQCMD_SET_TX_ON | (status & SEEQCMD_INT_MASK), SEEQ_CMD);
-
-}
-
-
-#ifdef MODULE
-
-static struct net_device *dev_seeq;
-MODULE_LICENSE("GPL");
-module_param(io, int, 0);
-module_param(irq, int, 0);
-MODULE_PARM_DESC(io, "SEEQ 8005 I/O base address");
-MODULE_PARM_DESC(irq, "SEEQ 8005 IRQ number");
-
-int __init init_module(void)
-{
-	dev_seeq = seeq8005_probe(-1);
-	if (IS_ERR(dev_seeq))
-		return PTR_ERR(dev_seeq);
-	return 0;
-}
-
-void __exit cleanup_module(void)
-{
-	unregister_netdev(dev_seeq);
-	release_region(dev_seeq->base_addr, SEEQ8005_IO_EXTENT);
-	free_netdev(dev_seeq);
-}
-
-#endif /* MODULE */