net: fec: setup right value for mdio hold time

The FEC modules used on i.MX28 and newer have a register to tune the MDIO
output hold time that should be at least 10 ns. Up to now this value was not
explicitly set and so resulted in less hold time if the fec clock was
faster than 100 MHz.

This was noticed on an i.MX28 machine that uses an input clock of ~150
Mhz which resulted in unreliable communication with a Marvell switch.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

1 files changed, 27 insertions, 3 deletions

diff --git a/drivers/net/ethernet/freescale/fec_main.c b/drivers/net/ethernet/freescale/fec_main.c
index b5039b37c79e..20dc442c9a79 100644
--- a/drivers/net/ethernet/freescale/fec_main.c
+++ b/drivers/net/ethernet/freescale/fec_main.c
@@ -1980,6 +1980,7 @@ static int fec_enet_mii_init(struct platform_device *pdev)
 	struct fec_enet_private *fep = netdev_priv(ndev);
 	struct device_node *node;
 	int err = -ENXIO, i;
+	u32 mii_speed, holdtime;
 
 	/*
 	 * The dual fec interfaces are not equivalent with enet-mac.
@@ -2018,10 +2019,33 @@ static int fec_enet_mii_init(struct platform_device *pdev)
 	 * Reference Manual has an error on this, and gets fixed on i.MX6Q
 	 * document.
 	 */
-	fep->phy_speed = DIV_ROUND_UP(clk_get_rate(fep->clk_ipg), 5000000);
+	mii_speed = DIV_ROUND_UP(clk_get_rate(fep->clk_ipg), 5000000);
 	if (fep->quirks & FEC_QUIRK_ENET_MAC)
-		fep->phy_speed--;
-	fep->phy_speed <<= 1;
+		mii_speed--;
+	if (mii_speed > 63) {
+		dev_err(&pdev->dev,
+			"fec clock (%lu) to fast to get right mii speed\n",
+			clk_get_rate(fep->clk_ipg));
+		err = -EINVAL;
+		goto err_out;
+	}
+
+	/*
+	 * The i.MX28 and i.MX6 types have another filed in the MSCR (aka
+	 * MII_SPEED) register that defines the MDIO output hold time. Earlier
+	 * versions are RAZ there, so just ignore the difference and write the
+	 * register always.
+	 * The minimal hold time according to IEE802.3 (clause 22) is 10 ns.
+	 * HOLDTIME + 1 is the number of clk cycles the fec is holding the
+	 * output.
+	 * The HOLDTIME bitfield takes values between 0 and 7 (inclusive).
+	 * Given that ceil(clkrate / 5000000) <= 64, the calculation for
+	 * holdtime cannot result in a value greater than 3.
+	 */
+	holdtime = DIV_ROUND_UP(clk_get_rate(fep->clk_ipg), 100000000) - 1;
+
+	fep->phy_speed = mii_speed << 1 | holdtime << 8;
+
 	writel(fep->phy_speed, fep->hwp + FEC_MII_SPEED);
 
 	fep->mii_bus = mdiobus_alloc();