summaryrefslogtreecommitdiff
path: root/drivers/parport/parport_mfc3.c
diff options
context:
space:
mode:
authorLinus Torvalds <torvalds@ppc970.osdl.org>2005-04-16 15:20:36 -0700
committerLinus Torvalds <torvalds@ppc970.osdl.org>2005-04-16 15:20:36 -0700
commit1da177e4c3f41524e886b7f1b8a0c1fc7321cac2 (patch)
tree0bba044c4ce775e45a88a51686b5d9f90697ea9d /drivers/parport/parport_mfc3.c
Linux-2.6.12-rc2v2.6.12-rc2
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
Diffstat (limited to 'drivers/parport/parport_mfc3.c')
-rw-r--r--drivers/parport/parport_mfc3.c404
1 files changed, 404 insertions, 0 deletions
diff --git a/drivers/parport/parport_mfc3.c b/drivers/parport/parport_mfc3.c
new file mode 100644
index 000000000000..c85364765ef8
--- /dev/null
+++ b/drivers/parport/parport_mfc3.c
@@ -0,0 +1,404 @@
+/* Low-level parallel port routines for the Multiface 3 card
+ *
+ * Author: Joerg Dorchain <joerg@dorchain.net>
+ *
+ * (C) The elitist m68k Users(TM)
+ *
+ * based on the existing parport_amiga and lp_mfc
+ *
+ *
+ * From the MFC3 documentation:
+ *
+ * Miscellaneous PIA Details
+ * -------------------------
+ *
+ * The two open-drain interrupt outputs /IRQA and /IRQB are routed to
+ * /INT2 of the Z2 bus.
+ *
+ * The CPU data bus of the PIA (D0-D7) is connected to D8-D15 on the Z2
+ * bus. This means that any PIA registers are accessed at even addresses.
+ *
+ * Centronics Pin Connections for the PIA
+ * --------------------------------------
+ *
+ * The following table shows the connections between the PIA and the
+ * Centronics interface connector. These connections implement a single, but
+ * very complete, Centronics type interface. The Pin column gives the pin
+ * numbers of the PIA. The Centronics pin numbers can be found in the section
+ * "Parallel Connectors".
+ *
+ *
+ * Pin | PIA | Dir | Centronics Names
+ * -------+-----+-----+---------------------------------------------------------
+ * 19 | CB2 | --> | /STROBE (aka /DRDY)
+ * 10-17 | PBx | <-> | DATA0 - DATA7
+ * 18 | CB1 | <-- | /ACK
+ * 40 | CA1 | <-- | BUSY
+ * 3 | PA1 | <-- | PAPER-OUT (aka POUT)
+ * 4 | PA2 | <-- | SELECTED (aka SEL)
+ * 9 | PA7 | --> | /INIT (aka /RESET or /INPUT-PRIME)
+ * 6 | PA4 | <-- | /ERROR (aka /FAULT)
+ * 7 | PA5 | --> | DIR (aka /SELECT-IN)
+ * 8 | PA6 | --> | /AUTO-FEED-XT
+ * 39 | CA2 | --> | open
+ * 5 | PA3 | <-- | /ACK (same as CB1!)
+ * 2 | PA0 | <-- | BUSY (same as CA1!)
+ * -------+-----+-----+---------------------------------------------------------
+ *
+ * Should be enough to understand some of the driver.
+ *
+ * Per convention for normal use the port registers are visible.
+ * If you need the data direction registers, restore the value in the
+ * control register.
+ */
+
+#include "multiface.h"
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/parport.h>
+#include <linux/delay.h>
+#include <linux/mc6821.h>
+#include <linux/zorro.h>
+#include <linux/interrupt.h>
+#include <asm/setup.h>
+#include <asm/amigahw.h>
+#include <asm/irq.h>
+#include <asm/amigaints.h>
+
+/* Maximum Number of Cards supported */
+#define MAX_MFC 5
+
+#undef DEBUG
+#ifdef DEBUG
+#define DPRINTK printk
+#else
+static inline int DPRINTK(void *nothing, ...) {return 0;}
+#endif
+
+static struct parport *this_port[MAX_MFC] = {NULL, };
+static volatile int dummy; /* for trigger readds */
+
+#define pia(dev) ((struct pia *)(dev->base))
+static struct parport_operations pp_mfc3_ops;
+
+static void mfc3_write_data(struct parport *p, unsigned char data)
+{
+DPRINTK(KERN_DEBUG "write_data %c\n",data);
+
+ dummy = pia(p)->pprb; /* clears irq bit */
+ /* Triggers also /STROBE.*/
+ pia(p)->pprb = data;
+}
+
+static unsigned char mfc3_read_data(struct parport *p)
+{
+ /* clears interrupt bit. Triggers also /STROBE. */
+ return pia(p)->pprb;
+}
+
+static unsigned char control_pc_to_mfc3(unsigned char control)
+{
+ unsigned char ret = 32|64;
+
+ if (control & PARPORT_CONTROL_SELECT) /* XXX: What is SELECP? */
+ ret &= ~32; /* /SELECT_IN */
+ if (control & PARPORT_CONTROL_INIT) /* INITP */
+ ret |= 128;
+ if (control & PARPORT_CONTROL_AUTOFD) /* AUTOLF */
+ ret &= ~64;
+ if (control & PARPORT_CONTROL_STROBE) /* Strobe */
+ /* Handled directly by hardware */;
+ return ret;
+}
+
+static unsigned char control_mfc3_to_pc(unsigned char control)
+{
+ unsigned char ret = PARPORT_CONTROL_STROBE
+ | PARPORT_CONTROL_AUTOFD | PARPORT_CONTROL_SELECT;
+
+ if (control & 128) /* /INITP */
+ ret |= PARPORT_CONTROL_INIT;
+ if (control & 64) /* /AUTOLF */
+ ret &= ~PARPORT_CONTROL_AUTOFD;
+ if (control & 32) /* /SELECT_IN */
+ ret &= ~PARPORT_CONTROL_SELECT;
+ return ret;
+}
+
+static void mfc3_write_control(struct parport *p, unsigned char control)
+{
+DPRINTK(KERN_DEBUG "write_control %02x\n",control);
+ pia(p)->ppra = (pia(p)->ppra & 0x1f) | control_pc_to_mfc3(control);
+}
+
+static unsigned char mfc3_read_control( struct parport *p)
+{
+DPRINTK(KERN_DEBUG "read_control \n");
+ return control_mfc3_to_pc(pia(p)->ppra & 0xe0);
+}
+
+static unsigned char mfc3_frob_control( struct parport *p, unsigned char mask, unsigned char val)
+{
+ unsigned char old;
+
+DPRINTK(KERN_DEBUG "frob_control mask %02x, value %02x\n",mask,val);
+ old = mfc3_read_control(p);
+ mfc3_write_control(p, (old & ~mask) ^ val);
+ return old;
+}
+
+#if 0 /* currently unused */
+static unsigned char status_pc_to_mfc3(unsigned char status)
+{
+ unsigned char ret = 1;
+
+ if (status & PARPORT_STATUS_BUSY) /* Busy */
+ ret &= ~1;
+ if (status & PARPORT_STATUS_ACK) /* Ack */
+ ret |= 8;
+ if (status & PARPORT_STATUS_PAPEROUT) /* PaperOut */
+ ret |= 2;
+ if (status & PARPORT_STATUS_SELECT) /* select */
+ ret |= 4;
+ if (status & PARPORT_STATUS_ERROR) /* error */
+ ret |= 16;
+ return ret;
+}
+#endif
+
+static unsigned char status_mfc3_to_pc(unsigned char status)
+{
+ unsigned char ret = PARPORT_STATUS_BUSY;
+
+ if (status & 1) /* Busy */
+ ret &= ~PARPORT_STATUS_BUSY;
+ if (status & 2) /* PaperOut */
+ ret |= PARPORT_STATUS_PAPEROUT;
+ if (status & 4) /* Selected */
+ ret |= PARPORT_STATUS_SELECT;
+ if (status & 8) /* Ack */
+ ret |= PARPORT_STATUS_ACK;
+ if (status & 16) /* /ERROR */
+ ret |= PARPORT_STATUS_ERROR;
+
+ return ret;
+}
+
+#if 0 /* currently unused */
+static void mfc3_write_status( struct parport *p, unsigned char status)
+{
+DPRINTK(KERN_DEBUG "write_status %02x\n",status);
+ pia(p)->ppra = (pia(p)->ppra & 0xe0) | status_pc_to_mfc3(status);
+}
+#endif
+
+static unsigned char mfc3_read_status(struct parport *p)
+{
+ unsigned char status;
+
+ status = status_mfc3_to_pc(pia(p)->ppra & 0x1f);
+DPRINTK(KERN_DEBUG "read_status %02x\n", status);
+ return status;
+}
+
+#if 0 /* currently unused */
+static void mfc3_change_mode( struct parport *p, int m)
+{
+ /* XXX: This port only has one mode, and I am
+ not sure about the corresponding PC-style mode*/
+}
+#endif
+
+static int use_cnt = 0;
+
+static irqreturn_t mfc3_interrupt(int irq, void *dev_id, struct pt_regs *regs)
+{
+ int i;
+
+ for( i = 0; i < MAX_MFC; i++)
+ if (this_port[i] != NULL)
+ if (pia(this_port[i])->crb & 128) { /* Board caused interrupt */
+ dummy = pia(this_port[i])->pprb; /* clear irq bit */
+ parport_generic_irq(irq, this_port[i], regs);
+ }
+ return IRQ_HANDLED;
+}
+
+static void mfc3_enable_irq(struct parport *p)
+{
+ pia(p)->crb |= PIA_C1_ENABLE_IRQ;
+}
+
+static void mfc3_disable_irq(struct parport *p)
+{
+ pia(p)->crb &= ~PIA_C1_ENABLE_IRQ;
+}
+
+static void mfc3_data_forward(struct parport *p)
+{
+ DPRINTK(KERN_DEBUG "forward\n");
+ pia(p)->crb &= ~PIA_DDR; /* make data direction register visible */
+ pia(p)->pddrb = 255; /* all pins output */
+ pia(p)->crb |= PIA_DDR; /* make data register visible - default */
+}
+
+static void mfc3_data_reverse(struct parport *p)
+{
+ DPRINTK(KERN_DEBUG "reverse\n");
+ pia(p)->crb &= ~PIA_DDR; /* make data direction register visible */
+ pia(p)->pddrb = 0; /* all pins input */
+ pia(p)->crb |= PIA_DDR; /* make data register visible - default */
+}
+
+static void mfc3_init_state(struct pardevice *dev, struct parport_state *s)
+{
+ s->u.amiga.data = 0;
+ s->u.amiga.datadir = 255;
+ s->u.amiga.status = 0;
+ s->u.amiga.statusdir = 0xe0;
+}
+
+static void mfc3_save_state(struct parport *p, struct parport_state *s)
+{
+ s->u.amiga.data = pia(p)->pprb;
+ pia(p)->crb &= ~PIA_DDR;
+ s->u.amiga.datadir = pia(p)->pddrb;
+ pia(p)->crb |= PIA_DDR;
+ s->u.amiga.status = pia(p)->ppra;
+ pia(p)->cra &= ~PIA_DDR;
+ s->u.amiga.statusdir = pia(p)->pddrb;
+ pia(p)->cra |= PIA_DDR;
+}
+
+static void mfc3_restore_state(struct parport *p, struct parport_state *s)
+{
+ pia(p)->pprb = s->u.amiga.data;
+ pia(p)->crb &= ~PIA_DDR;
+ pia(p)->pddrb = s->u.amiga.datadir;
+ pia(p)->crb |= PIA_DDR;
+ pia(p)->ppra = s->u.amiga.status;
+ pia(p)->cra &= ~PIA_DDR;
+ pia(p)->pddrb = s->u.amiga.statusdir;
+ pia(p)->cra |= PIA_DDR;
+}
+
+static struct parport_operations pp_mfc3_ops = {
+ .write_data = mfc3_write_data,
+ .read_data = mfc3_read_data,
+
+ .write_control = mfc3_write_control,
+ .read_control = mfc3_read_control,
+ .frob_control = mfc3_frob_control,
+
+ .read_status = mfc3_read_status,
+
+ .enable_irq = mfc3_enable_irq,
+ .disable_irq = mfc3_disable_irq,
+
+ .data_forward = mfc3_data_forward,
+ .data_reverse = mfc3_data_reverse,
+
+ .init_state = mfc3_init_state,
+ .save_state = mfc3_save_state,
+ .restore_state = mfc3_restore_state,
+
+ .epp_write_data = parport_ieee1284_epp_write_data,
+ .epp_read_data = parport_ieee1284_epp_read_data,
+ .epp_write_addr = parport_ieee1284_epp_write_addr,
+ .epp_read_addr = parport_ieee1284_epp_read_addr,
+
+ .ecp_write_data = parport_ieee1284_ecp_write_data,
+ .ecp_read_data = parport_ieee1284_ecp_read_data,
+ .ecp_write_addr = parport_ieee1284_ecp_write_addr,
+
+ .compat_write_data = parport_ieee1284_write_compat,
+ .nibble_read_data = parport_ieee1284_read_nibble,
+ .byte_read_data = parport_ieee1284_read_byte,
+
+ .owner = THIS_MODULE,
+};
+
+/* ----------- Initialisation code --------------------------------- */
+
+static int __init parport_mfc3_init(void)
+{
+ struct parport *p;
+ int pias = 0;
+ struct pia *pp;
+ struct zorro_dev *z = NULL;
+
+ if (!MACH_IS_AMIGA)
+ return -ENODEV;
+
+ while ((z = zorro_find_device(ZORRO_PROD_BSC_MULTIFACE_III, z))) {
+ unsigned long piabase = z->resource.start+PIABASE;
+ if (!request_mem_region(piabase, sizeof(struct pia), "PIA"))
+ continue;
+
+ pp = (struct pia *)ZTWO_VADDR(piabase);
+ pp->crb = 0;
+ pp->pddrb = 255; /* all data pins output */
+ pp->crb = PIA_DDR|32|8;
+ dummy = pp->pddrb; /* reading clears interrupt */
+ pp->cra = 0;
+ pp->pddra = 0xe0; /* /RESET, /DIR ,/AUTO-FEED output */
+ pp->cra = PIA_DDR;
+ pp->ppra = 0; /* reset printer */
+ udelay(10);
+ pp->ppra = 128;
+ p = parport_register_port((unsigned long)pp, IRQ_AMIGA_PORTS,
+ PARPORT_DMA_NONE, &pp_mfc3_ops);
+ if (!p)
+ goto out_port;
+
+ if (p->irq != PARPORT_IRQ_NONE) {
+ if (use_cnt++ == 0)
+ if (request_irq(IRQ_AMIGA_PORTS, mfc3_interrupt, SA_SHIRQ, p->name, &pp_mfc3_ops))
+ goto out_irq;
+ }
+
+ this_port[pias++] = p;
+ printk(KERN_INFO "%s: Multiface III port using irq\n", p->name);
+ /* XXX: set operating mode */
+
+ p->private_data = (void *)piabase;
+ parport_announce_port (p);
+
+ if (pias >= MAX_MFC)
+ break;
+ continue;
+
+ out_irq:
+ parport_put_port(p);
+ out_port:
+ release_mem_region(piabase, sizeof(struct pia));
+ }
+
+ return pias ? 0 : -ENODEV;
+}
+
+static void __exit parport_mfc3_exit(void)
+{
+ int i;
+
+ for (i = 0; i < MAX_MFC; i++) {
+ if (!this_port[i])
+ continue;
+ parport_remove_port(this_port[i]);
+ if (!this_port[i]->irq != PARPORT_IRQ_NONE) {
+ if (--use_cnt == 0)
+ free_irq(IRQ_AMIGA_PORTS, &pp_mfc3_ops);
+ }
+ release_mem_region(ZTWO_PADDR(this_port[i]->private_data), sizeof(struct pia));
+ parport_put_port(this_port[i]);
+ }
+}
+
+
+MODULE_AUTHOR("Joerg Dorchain <joerg@dorchain.net>");
+MODULE_DESCRIPTION("Parport Driver for Multiface 3 expansion cards Paralllel Port");
+MODULE_SUPPORTED_DEVICE("Multiface 3 Parallel Port");
+MODULE_LICENSE("GPL");
+
+module_init(parport_mfc3_init)
+module_exit(parport_mfc3_exit)