Merge branch 'devel-stable' into devel

Conflicts:
	arch/arm/mach-pxa/clock.c
	arch/arm/mach-pxa/clock.h

6 files changed, 393 insertions, 12 deletions

diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index 6f4f8e6a40c7..f8970d151d2a 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -147,6 +147,14 @@ config USB_W90X900_EHCI
 	---help---
 		Enables support for the W90X900 USB controller
 
+config USB_CNS3XXX_EHCI
+	bool "Cavium CNS3XXX EHCI Module"
+	depends on USB_EHCI_HCD && ARCH_CNS3XXX
+	---help---
+	  Enable support for the CNS3XXX SOC's on-chip EHCI controller.
+	  It is needed for high-speed (480Mbit/sec) USB 2.0 device
+	  support.
+
 config USB_OXU210HP_HCD
 	tristate "OXU210HP HCD support"
 	depends on USB
@@ -286,6 +294,13 @@ config USB_OHCI_HCD_SSB
 
 	  If unsure, say N.
 
+config USB_CNS3XXX_OHCI
+	bool "Cavium CNS3XXX OHCI Module"
+	depends on USB_OHCI_HCD && ARCH_CNS3XXX
+	---help---
+	  Enable support for the CNS3XXX SOC's on-chip OHCI controller.
+	  It is needed for low-speed USB 1.0 device support.
+
 config USB_OHCI_BIG_ENDIAN_DESC
 	bool
 	depends on USB_OHCI_HCD
diff --git a/drivers/usb/host/ehci-cns3xxx.c b/drivers/usb/host/ehci-cns3xxx.c
new file mode 100644
index 000000000000..708a05b5d258
--- /dev/null
+++ b/drivers/usb/host/ehci-cns3xxx.c
@@ -0,0 +1,171 @@
+/*
+ * Copyright 2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/atomic.h>
+#include <mach/cns3xxx.h>
+#include <mach/pm.h>
+
+static int cns3xxx_ehci_init(struct usb_hcd *hcd)
+{
+	struct ehci_hcd *ehci = hcd_to_ehci(hcd);
+	int retval;
+
+	/*
+	 * EHCI and OHCI share the same clock and power,
+	 * resetting twice would cause the 1st controller been reset.
+	 * Therefore only do power up  at the first up device, and
+	 * power down at the last down device.
+	 *
+	 * Set USB AHB INCR length to 16
+	 */
+	if (atomic_inc_return(&usb_pwr_ref) == 1) {
+		cns3xxx_pwr_power_up(1 << PM_PLL_HM_PD_CTRL_REG_OFFSET_PLL_USB);
+		cns3xxx_pwr_clk_en(1 << PM_CLK_GATE_REG_OFFSET_USB_HOST);
+		cns3xxx_pwr_soft_rst(1 << PM_SOFT_RST_REG_OFFST_USB_HOST);
+		__raw_writel((__raw_readl(MISC_CHIP_CONFIG_REG) | (0X2 << 24)),
+			MISC_CHIP_CONFIG_REG);
+	}
+
+	ehci->caps = hcd->regs;
+	ehci->regs = hcd->regs
+		+ HC_LENGTH(ehci_readl(ehci, &ehci->caps->hc_capbase));
+	ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params);
+
+	hcd->has_tt = 0;
+	ehci_reset(ehci);
+
+	retval = ehci_init(hcd);
+	if (retval)
+		return retval;
+
+	ehci_port_power(ehci, 0);
+
+	return retval;
+}
+
+static const struct hc_driver cns3xxx_ehci_hc_driver = {
+	.description		= hcd_name,
+	.product_desc		= "CNS3XXX EHCI Host Controller",
+	.hcd_priv_size		= sizeof(struct ehci_hcd),
+	.irq			= ehci_irq,
+	.flags			= HCD_MEMORY | HCD_USB2,
+	.reset			= cns3xxx_ehci_init,
+	.start			= ehci_run,
+	.stop			= ehci_stop,
+	.shutdown		= ehci_shutdown,
+	.urb_enqueue		= ehci_urb_enqueue,
+	.urb_dequeue		= ehci_urb_dequeue,
+	.endpoint_disable	= ehci_endpoint_disable,
+	.endpoint_reset		= ehci_endpoint_reset,
+	.get_frame_number	= ehci_get_frame,
+	.hub_status_data	= ehci_hub_status_data,
+	.hub_control		= ehci_hub_control,
+#ifdef CONFIG_PM
+	.bus_suspend		= ehci_bus_suspend,
+	.bus_resume		= ehci_bus_resume,
+#endif
+	.relinquish_port	= ehci_relinquish_port,
+	.port_handed_over	= ehci_port_handed_over,
+
+	.clear_tt_buffer_complete	= ehci_clear_tt_buffer_complete,
+};
+
+static int cns3xxx_ehci_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct usb_hcd *hcd;
+	const struct hc_driver *driver = &cns3xxx_ehci_hc_driver;
+	struct resource *res;
+	int irq;
+	int retval;
+
+	if (usb_disabled())
+		return -ENODEV;
+
+	res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+	if (!res) {
+		dev_err(dev, "Found HC with no IRQ.\n");
+		return -ENODEV;
+	}
+	irq = res->start;
+
+	hcd = usb_create_hcd(driver, &pdev->dev, dev_name(&pdev->dev));
+	if (!hcd)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(dev, "Found HC with no register addr.\n");
+		retval = -ENODEV;
+		goto err1;
+	}
+
+	hcd->rsrc_start = res->start;
+	hcd->rsrc_len = res->end - res->start + 1;
+
+	if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len,
+				driver->description)) {
+		dev_dbg(dev, "controller already in use\n");
+		retval = -EBUSY;
+		goto err1;
+	}
+
+	hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
+	if (hcd->regs == NULL) {
+		dev_dbg(dev, "error mapping memory\n");
+		retval = -EFAULT;
+		goto err2;
+	}
+
+	retval = usb_add_hcd(hcd, irq, IRQF_SHARED);
+	if (retval == 0)
+		return retval;
+
+	iounmap(hcd->regs);
+err2:
+	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+err1:
+	usb_put_hcd(hcd);
+
+	return retval;
+}
+
+static int cns3xxx_ehci_remove(struct platform_device *pdev)
+{
+	struct usb_hcd *hcd = platform_get_drvdata(pdev);
+
+	usb_remove_hcd(hcd);
+	iounmap(hcd->regs);
+	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+
+	/*
+	 * EHCI and OHCI share the same clock and power,
+	 * resetting twice would cause the 1st controller been reset.
+	 * Therefore only do power up  at the first up device, and
+	 * power down at the last down device.
+	 */
+	if (atomic_dec_return(&usb_pwr_ref) == 0)
+		cns3xxx_pwr_clk_dis(1 << PM_CLK_GATE_REG_OFFSET_USB_HOST);
+
+	usb_put_hcd(hcd);
+
+	platform_set_drvdata(pdev, NULL);
+
+	return 0;
+}
+
+MODULE_ALIAS("platform:cns3xxx-ehci");
+
+static struct platform_driver cns3xxx_ehci_driver = {
+	.probe = cns3xxx_ehci_probe,
+	.remove = cns3xxx_ehci_remove,
+	.driver = {
+		.name = "cns3xxx-ehci",
+	},
+};
diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c
index e9062806d4a2..d0c8f7c03e05 100644
--- a/drivers/usb/host/ehci-hcd.c
+++ b/drivers/usb/host/ehci-hcd.c
@@ -1216,6 +1216,11 @@ MODULE_LICENSE ("GPL");
 #define PLATFORM_DRIVER		ehci_octeon_driver
 #endif
 
+#ifdef CONFIG_USB_CNS3XXX_EHCI
+#include "ehci-cns3xxx.c"
+#define PLATFORM_DRIVER		cns3xxx_ehci_driver
+#endif
+
 #if !defined(PCI_DRIVER) && !defined(PLATFORM_DRIVER) && \
     !defined(PS3_SYSTEM_BUS_DRIVER) && !defined(OF_PLATFORM_DRIVER) && \
     !defined(XILINX_OF_PLATFORM_DRIVER)
diff --git a/drivers/usb/host/ehci-mxc.c b/drivers/usb/host/ehci-mxc.c
index bce85055019a..a22d2df769a9 100644
--- a/drivers/usb/host/ehci-mxc.c
+++ b/drivers/usb/host/ehci-mxc.c
@@ -28,7 +28,7 @@
 #define ULPI_VIEWPORT_OFFSET	0x170
 
 struct ehci_mxc_priv {
-	struct clk *usbclk, *ahbclk;
+	struct clk *usbclk, *ahbclk, *phy1clk;
 	struct usb_hcd *hcd;
 };
 
@@ -168,17 +168,6 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev)
 		goto err_ioremap;
 	}
 
-	/* call platform specific init function */
-	if (pdata->init) {
-		ret = pdata->init(pdev);
-		if (ret) {
-			dev_err(dev, "platform init failed\n");
-			goto err_init;
-		}
-		/* platforms need some time to settle changed IO settings */
-		mdelay(10);
-	}
-
 	/* enable clocks */
 	priv->usbclk = clk_get(dev, "usb");
 	if (IS_ERR(priv->usbclk)) {
@@ -196,6 +185,28 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev)
 		clk_enable(priv->ahbclk);
 	}
 
+	/* "dr" device has its own clock */
+	if (pdev->id == 0) {
+		priv->phy1clk = clk_get(dev, "usb_phy1");
+		if (IS_ERR(priv->phy1clk)) {
+			ret = PTR_ERR(priv->phy1clk);
+			goto err_clk_phy;
+		}
+		clk_enable(priv->phy1clk);
+	}
+
+
+	/* call platform specific init function */
+	if (pdata->init) {
+		ret = pdata->init(pdev);
+		if (ret) {
+			dev_err(dev, "platform init failed\n");
+			goto err_init;
+		}
+		/* platforms need some time to settle changed IO settings */
+		mdelay(10);
+	}
+
 	/* setup specific usb hw */
 	ret = mxc_initialize_usb_hw(pdev->id, pdata->flags);
 	if (ret < 0)
@@ -230,6 +241,11 @@ err_add:
 	if (pdata && pdata->exit)
 		pdata->exit(pdev);
 err_init:
+	if (priv->phy1clk) {
+		clk_disable(priv->phy1clk);
+		clk_put(priv->phy1clk);
+	}
+err_clk_phy:
 	if (priv->ahbclk) {
 		clk_disable(priv->ahbclk);
 		clk_put(priv->ahbclk);
@@ -273,6 +289,10 @@ static int __exit ehci_mxc_drv_remove(struct platform_device *pdev)
 		clk_disable(priv->ahbclk);
 		clk_put(priv->ahbclk);
 	}
+	if (priv->phy1clk) {
+		clk_disable(priv->phy1clk);
+		clk_put(priv->phy1clk);
+	}
 
 	kfree(priv);
 
diff --git a/drivers/usb/host/ohci-cns3xxx.c b/drivers/usb/host/ohci-cns3xxx.c
new file mode 100644
index 000000000000..f05ef87e934c
--- /dev/null
+++ b/drivers/usb/host/ohci-cns3xxx.c
@@ -0,0 +1,165 @@
+/*
+ * Copyright 2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/atomic.h>
+#include <mach/cns3xxx.h>
+#include <mach/pm.h>
+
+static int __devinit
+cns3xxx_ohci_start(struct usb_hcd *hcd)
+{
+	struct ohci_hcd	*ohci = hcd_to_ohci(hcd);
+	int ret;
+
+	/*
+	 * EHCI and OHCI share the same clock and power,
+	 * resetting twice would cause the 1st controller been reset.
+	 * Therefore only do power up  at the first up device, and
+	 * power down at the last down device.
+	 *
+	 * Set USB AHB INCR length to 16
+	 */
+	if (atomic_inc_return(&usb_pwr_ref) == 1) {
+		cns3xxx_pwr_power_up(1 << PM_PLL_HM_PD_CTRL_REG_OFFSET_PLL_USB);
+		cns3xxx_pwr_clk_en(1 << PM_CLK_GATE_REG_OFFSET_USB_HOST);
+		cns3xxx_pwr_soft_rst(1 << PM_SOFT_RST_REG_OFFST_USB_HOST);
+		__raw_writel((__raw_readl(MISC_CHIP_CONFIG_REG) | (0X2 << 24)),
+			MISC_CHIP_CONFIG_REG);
+	}
+
+	ret = ohci_init(ohci);
+	if (ret < 0)
+		return ret;
+
+	ohci->num_ports = 1;
+
+	ret = ohci_run(ohci);
+	if (ret < 0) {
+		err("can't start %s", hcd->self.bus_name);
+		ohci_stop(hcd);
+		return ret;
+	}
+	return 0;
+}
+
+static const struct hc_driver cns3xxx_ohci_hc_driver = {
+	.description		= hcd_name,
+	.product_desc		= "CNS3XXX OHCI Host controller",
+	.hcd_priv_size		= sizeof(struct ohci_hcd),
+	.irq			= ohci_irq,
+	.flags			= HCD_USB11 | HCD_MEMORY,
+	.start			= cns3xxx_ohci_start,
+	.stop			= ohci_stop,
+	.shutdown		= ohci_shutdown,
+	.urb_enqueue		= ohci_urb_enqueue,
+	.urb_dequeue		= ohci_urb_dequeue,
+	.endpoint_disable	= ohci_endpoint_disable,
+	.get_frame_number	= ohci_get_frame,
+	.hub_status_data	= ohci_hub_status_data,
+	.hub_control		= ohci_hub_control,
+#ifdef CONFIG_PM
+	.bus_suspend		= ohci_bus_suspend,
+	.bus_resume		= ohci_bus_resume,
+#endif
+	.start_port_reset	= ohci_start_port_reset,
+};
+
+static int cns3xxx_ohci_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct usb_hcd *hcd;
+	const struct hc_driver *driver = &cns3xxx_ohci_hc_driver;
+	struct resource *res;
+	int irq;
+	int retval;
+
+	if (usb_disabled())
+		return -ENODEV;
+
+	res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+	if (!res) {
+		dev_err(dev, "Found HC with no IRQ.\n");
+		return -ENODEV;
+	}
+	irq = res->start;
+
+	hcd = usb_create_hcd(driver, dev, dev_name(dev));
+	if (!hcd)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(dev, "Found HC with no register addr.\n");
+		retval = -ENODEV;
+		goto err1;
+	}
+	hcd->rsrc_start = res->start;
+	hcd->rsrc_len = res->end - res->start + 1;
+
+	if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len,
+			driver->description)) {
+		dev_dbg(dev, "controller already in use\n");
+		retval = -EBUSY;
+		goto err1;
+	}
+
+	hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
+	if (!hcd->regs) {
+		dev_dbg(dev, "error mapping memory\n");
+		retval = -EFAULT;
+		goto err2;
+	}
+
+	ohci_hcd_init(hcd_to_ohci(hcd));
+
+	retval = usb_add_hcd(hcd, irq, IRQF_SHARED);
+	if (retval == 0)
+		return retval;
+
+	iounmap(hcd->regs);
+err2:
+	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+err1:
+	usb_put_hcd(hcd);
+	return retval;
+}
+
+static int cns3xxx_ohci_remove(struct platform_device *pdev)
+{
+	struct usb_hcd *hcd = platform_get_drvdata(pdev);
+
+	usb_remove_hcd(hcd);
+	iounmap(hcd->regs);
+	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+
+	/*
+	 * EHCI and OHCI share the same clock and power,
+	 * resetting twice would cause the 1st controller been reset.
+	 * Therefore only do power up  at the first up device, and
+	 * power down at the last down device.
+	 */
+	if (atomic_dec_return(&usb_pwr_ref) == 0)
+		cns3xxx_pwr_clk_dis(1 << PM_CLK_GATE_REG_OFFSET_USB_HOST);
+
+	usb_put_hcd(hcd);
+
+	platform_set_drvdata(pdev, NULL);
+
+	return 0;
+}
+
+MODULE_ALIAS("platform:cns3xxx-ohci");
+
+static struct platform_driver ohci_hcd_cns3xxx_driver = {
+	.probe = cns3xxx_ohci_probe,
+	.remove = cns3xxx_ohci_remove,
+	.driver = {
+		.name = "cns3xxx-ohci",
+	},
+};
diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c
index 5179acb7aa2f..5cb6731ba443 100644
--- a/drivers/usb/host/ohci-hcd.c
+++ b/drivers/usb/host/ohci-hcd.c
@@ -1111,6 +1111,11 @@ MODULE_LICENSE ("GPL");
 #define PLATFORM_DRIVER		ohci_octeon_driver
 #endif
 
+#ifdef CONFIG_USB_CNS3XXX_OHCI
+#include "ohci-cns3xxx.c"
+#define PLATFORM_DRIVER		ohci_hcd_cns3xxx_driver
+#endif
+
 #if	!defined(PCI_DRIVER) &&		\
 	!defined(PLATFORM_DRIVER) &&	\
 	!defined(OMAP1_PLATFORM_DRIVER) &&	\