Merge branch 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata

Pull libata fixes from Tejun Heo:
 "Two patches are to add PCI IDs for ICH9 and all others are device
  specific fixes.  Nothing too interesting"

* 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  ahci_xgene: Fix the link down in first attempt for the APM X-Gene SoC AHCI SATA host controller driver.
  ahci_xgene: Skip the PHY and clock initialization if already configured by the firmware.
  ahci: add pcid for Marvel 0x9182 controller
  ata: Disabling the async PM for JMicron chip 363/361
  ata_piix: Add Device IDs for Intel 9 Series PCH
  ahci: Add Device IDs for Intel 9 Series PCH
  ata: ahci_tegra: Read calibration fuse

5 files changed, 99 insertions, 18 deletions

diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index a29f8012fb08..a0cc0edafc78 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -305,6 +305,14 @@ static const struct pci_device_id ahci_pci_tbl[] = {
 	{ PCI_VDEVICE(INTEL, 0x9c85), board_ahci }, /* Wildcat Point-LP RAID */
 	{ PCI_VDEVICE(INTEL, 0x9c87), board_ahci }, /* Wildcat Point-LP RAID */
 	{ PCI_VDEVICE(INTEL, 0x9c8f), board_ahci }, /* Wildcat Point-LP RAID */
+	{ PCI_VDEVICE(INTEL, 0x8c82), board_ahci }, /* 9 Series AHCI */
+	{ PCI_VDEVICE(INTEL, 0x8c83), board_ahci }, /* 9 Series AHCI */
+	{ PCI_VDEVICE(INTEL, 0x8c84), board_ahci }, /* 9 Series RAID */
+	{ PCI_VDEVICE(INTEL, 0x8c85), board_ahci }, /* 9 Series RAID */
+	{ PCI_VDEVICE(INTEL, 0x8c86), board_ahci }, /* 9 Series RAID */
+	{ PCI_VDEVICE(INTEL, 0x8c87), board_ahci }, /* 9 Series RAID */
+	{ PCI_VDEVICE(INTEL, 0x8c8e), board_ahci }, /* 9 Series RAID */
+	{ PCI_VDEVICE(INTEL, 0x8c8f), board_ahci }, /* 9 Series RAID */
 
 	/* JMicron 360/1/3/5/6, match class to avoid IDE function */
 	{ PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
@@ -442,6 +450,8 @@ static const struct pci_device_id ahci_pci_tbl[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL_EXT, 0x917a),
 	  .driver_data = board_ahci_yes_fbs },			/* 88se9172 */
 	{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL_EXT, 0x9172),
+	  .driver_data = board_ahci_yes_fbs },			/* 88se9182 */
+	{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL_EXT, 0x9182),
 	  .driver_data = board_ahci_yes_fbs },			/* 88se9172 */
 	{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL_EXT, 0x9192),
 	  .driver_data = board_ahci_yes_fbs },			/* 88se9172 on some Gigabyte */
@@ -1329,6 +1339,18 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 	else if (pdev->vendor == 0x1c44 && pdev->device == 0x8000)
 		ahci_pci_bar = AHCI_PCI_BAR_ENMOTUS;
 
+	/*
+	 * The JMicron chip 361/363 contains one SATA controller and one
+	 * PATA controller,for powering on these both controllers, we must
+	 * follow the sequence one by one, otherwise one of them can not be
+	 * powered on successfully, so here we disable the async suspend
+	 * method for these chips.
+	 */
+	if (pdev->vendor == PCI_VENDOR_ID_JMICRON &&
+		(pdev->device == PCI_DEVICE_ID_JMICRON_JMB363 ||
+		pdev->device == PCI_DEVICE_ID_JMICRON_JMB361))
+		device_disable_async_suspend(&pdev->dev);
+
 	/* acquire resources */
 	rc = pcim_enable_device(pdev);
 	if (rc)
diff --git a/drivers/ata/ahci_tegra.c b/drivers/ata/ahci_tegra.c
index f1fef74e503c..032904402c95 100644
--- a/drivers/ata/ahci_tegra.c
+++ b/drivers/ata/ahci_tegra.c
@@ -18,14 +18,17 @@
  */
 
 #include <linux/ahci_platform.h>
-#include <linux/reset.h>
 #include <linux/errno.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/regulator/consumer.h>
+#include <linux/reset.h>
+
+#include <soc/tegra/fuse.h>
 #include <soc/tegra/pmc.h>
+
 #include "ahci.h"
 
 #define SATA_CONFIGURATION_0				0x180
@@ -180,9 +183,12 @@ static int tegra_ahci_controller_init(struct ahci_host_priv *hpriv)
 
 	/* Pad calibration */
 
-	/* FIXME Always use calibration 0. Change this to read the calibration
-	 * fuse once the fuse driver has landed. */
-	val = 0;
+	ret = tegra_fuse_readl(FUSE_SATA_CALIB, &val);
+	if (ret) {
+		dev_err(&tegra->pdev->dev,
+			"failed to read calibration fuse: %d\n", ret);
+		return ret;
+	}
 
 	calib = tegra124_pad_calibration[val & FUSE_SATA_CALIB_MASK];
 
diff --git a/drivers/ata/ahci_xgene.c b/drivers/ata/ahci_xgene.c
index c6962300b93c..f03aab187f4d 100644
--- a/drivers/ata/ahci_xgene.c
+++ b/drivers/ata/ahci_xgene.c
@@ -78,6 +78,9 @@
 #define CFG_MEM_RAM_SHUTDOWN		0x00000070
 #define BLOCK_MEM_RDY			0x00000074
 
+/* Max retry for link down */
+#define MAX_LINK_DOWN_RETRY 3
+
 struct xgene_ahci_context {
 	struct ahci_host_priv *hpriv;
 	struct device *dev;
@@ -145,6 +148,14 @@ static unsigned int xgene_ahci_qc_issue(struct ata_queued_cmd *qc)
 	return rc;
 }
 
+static bool xgene_ahci_is_memram_inited(struct xgene_ahci_context *ctx)
+{
+	void __iomem *diagcsr = ctx->csr_diag;
+
+	return (readl(diagcsr + CFG_MEM_RAM_SHUTDOWN) == 0 &&
+	        readl(diagcsr + BLOCK_MEM_RDY) == 0xFFFFFFFF);
+}
+
 /**
  * xgene_ahci_read_id - Read ID data from the specified device
  * @dev: device
@@ -229,8 +240,11 @@ static void xgene_ahci_set_phy_cfg(struct xgene_ahci_context *ctx, int channel)
  * and Gen1 (1.5Gbps). Otherwise during long IO stress test, the PHY will
  * report disparity error and etc. In addition, during COMRESET, there can
  * be error reported in the register PORT_SCR_ERR. For SERR_DISPARITY and
- * SERR_10B_8B_ERR, the PHY receiver line must be reseted. The following
- * algorithm is followed to proper configure the hardware PHY during COMRESET:
+ * SERR_10B_8B_ERR, the PHY receiver line must be reseted. Also during long
+ * reboot cycle regression, sometimes the PHY reports link down even if the
+ * device is present because of speed negotiation failure. so need to retry
+ * the COMRESET to get the link up. The following algorithm is followed to
+ * proper configure the hardware PHY during COMRESET:
  *
  * Alg Part 1:
  * 1. Start the PHY at Gen3 speed (default setting)
@@ -246,9 +260,15 @@ static void xgene_ahci_set_phy_cfg(struct xgene_ahci_context *ctx, int channel)
  * Alg Part 2:
  * 1. On link up, if there are any SERR_DISPARITY and SERR_10B_8B_ERR error
  *    reported in the register PORT_SCR_ERR, then reset the PHY receiver line
- * 2. Go to Alg Part 3
+ * 2. Go to Alg Part 4
  *
  * Alg Part 3:
+ * 1. Check the PORT_SCR_STAT to see whether device presence detected but PHY
+ *    communication establishment failed and maximum link down attempts are
+ *    less than Max attempts 3 then goto Alg Part 1.
+ * 2. Go to Alg Part 4.
+ *
+ * Alg Part 4:
  * 1. Clear any pending from register PORT_SCR_ERR.
  *
  * NOTE: For the initial version, we will NOT support Gen1/Gen2. In addition
@@ -267,19 +287,27 @@ static int xgene_ahci_do_hardreset(struct ata_link *link,
 	u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
 	void __iomem *port_mmio = ahci_port_base(ap);
 	struct ata_taskfile tf;
+	int link_down_retry = 0;
 	int rc;
-	u32 val;
-
-	/* clear D2H reception area to properly wait for D2H FIS */
-	ata_tf_init(link->device, &tf);
-	tf.command = ATA_BUSY;
-	ata_tf_to_fis(&tf, 0, 0, d2h_fis);
-	rc = sata_link_hardreset(link, timing, deadline, online,
+	u32 val, sstatus;
+
+	do {
+		/* clear D2H reception area to properly wait for D2H FIS */
+		ata_tf_init(link->device, &tf);
+		tf.command = ATA_BUSY;
+		ata_tf_to_fis(&tf, 0, 0, d2h_fis);
+		rc = sata_link_hardreset(link, timing, deadline, online,
 				 ahci_check_ready);
+		if (*online) {
+			val = readl(port_mmio + PORT_SCR_ERR);
+			if (val & (SERR_DISPARITY | SERR_10B_8B_ERR))
+				dev_warn(ctx->dev, "link has error\n");
+			break;
+		}
 
-	val = readl(port_mmio + PORT_SCR_ERR);
-	if (val & (SERR_DISPARITY | SERR_10B_8B_ERR))
-		dev_warn(ctx->dev, "link has error\n");
+		sata_scr_read(link, SCR_STATUS, &sstatus);
+	} while (link_down_retry++ < MAX_LINK_DOWN_RETRY &&
+		 (sstatus & 0xff) == 0x1);
 
 	/* clear all errors if any pending */
 	val = readl(port_mmio + PORT_SCR_ERR);
@@ -467,6 +495,11 @@ static int xgene_ahci_probe(struct platform_device *pdev)
 		return -ENODEV;
 	}
 
+	if (xgene_ahci_is_memram_inited(ctx)) {
+		dev_info(dev, "skip clock and PHY initialization\n");
+		goto skip_clk_phy;
+	}
+
 	/* Due to errata, HW requires full toggle transition */
 	rc = ahci_platform_enable_clks(hpriv);
 	if (rc)
@@ -479,7 +512,7 @@ static int xgene_ahci_probe(struct platform_device *pdev)
 
 	/* Configure the host controller */
 	xgene_ahci_hw_init(hpriv);
-
+skip_clk_phy:
 	hpriv->flags = AHCI_HFLAG_NO_PMP | AHCI_HFLAG_NO_NCQ;
 
 	rc = ahci_platform_init_host(pdev, hpriv, &xgene_ahci_port_info);
diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index 893e30e9a9ef..ffbe625e6fd2 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -340,6 +340,14 @@ static const struct pci_device_id piix_pci_tbl[] = {
 	{ 0x8086, 0x0F21, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata_byt },
 	/* SATA Controller IDE (Coleto Creek) */
 	{ 0x8086, 0x23a6, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
+	/* SATA Controller IDE (9 Series) */
+	{ 0x8086, 0x8c88, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata_snb },
+	/* SATA Controller IDE (9 Series) */
+	{ 0x8086, 0x8c89, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata_snb },
+	/* SATA Controller IDE (9 Series) */
+	{ 0x8086, 0x8c80, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_snb },
+	/* SATA Controller IDE (9 Series) */
+	{ 0x8086, 0x8c81, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_snb },
 
 	{ }	/* terminate list */
 };
diff --git a/drivers/ata/pata_jmicron.c b/drivers/ata/pata_jmicron.c
index 4d1a5d2c4287..47e418b8c8ba 100644
--- a/drivers/ata/pata_jmicron.c
+++ b/drivers/ata/pata_jmicron.c
@@ -143,6 +143,18 @@ static int jmicron_init_one (struct pci_dev *pdev, const struct pci_device_id *i
 	};
 	const struct ata_port_info *ppi[] = { &info, NULL };
 
+	/*
+	 * The JMicron chip 361/363 contains one SATA controller and one
+	 * PATA controller,for powering on these both controllers, we must
+	 * follow the sequence one by one, otherwise one of them can not be
+	 * powered on successfully, so here we disable the async suspend
+	 * method for these chips.
+	 */
+	if (pdev->vendor == PCI_VENDOR_ID_JMICRON &&
+		(pdev->device == PCI_DEVICE_ID_JMICRON_JMB363 ||
+		pdev->device == PCI_DEVICE_ID_JMICRON_JMB361))
+		device_disable_async_suspend(&pdev->dev);
+
 	return ata_pci_bmdma_init_one(pdev, ppi, &jmicron_sht, NULL, 0);
 }