sh: migrate to arch/sh/include/

This follows the sparc changes a439fe51a1f8eb087c22dd24d69cebae4a3addac.

Most of the moving about was done with Sam's directions at:

http://marc.info/?l=linux-sh&m=121724823706062&w=2

with subsequent hacking and fixups entirely my fault.

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

3 files changed, 0 insertions, 346 deletions

diff --git a/include/asm-sh/hd64465/gpio.h b/include/asm-sh/hd64465/gpio.h
deleted file mode 100644
index a3cdca2713dd..000000000000
--- a/include/asm-sh/hd64465/gpio.h
+++ /dev/null
@@ -1,46 +0,0 @@
-#ifndef _ASM_SH_HD64465_GPIO_
-#define _ASM_SH_HD64465_GPIO_ 1
-/*
- * $Id: gpio.h,v 1.3 2003/05/04 19:30:14 lethal Exp $
- *
- * Hitachi HD64465 companion chip: General Purpose IO pins support.
- * This layer enables other device drivers to configure GPIO
- * pins, get and set their values, and register an interrupt
- * routine for when input pins change in hardware.
- *
- * by Greg Banks <gbanks@pocketpenguins.com>
- * (c) 2000 PocketPenguins Inc.
- */
-#include <asm/hd64465.h>
-
-/* Macro to construct a portpin number (used in all
- * subsequent functions) from a port letter and a pin
- * number, e.g. HD64465_GPIO_PORTPIN('A', 5).
- */
-#define HD64465_GPIO_PORTPIN(port,pin)	(((port)-'A')<<3|(pin))
-
-/* Pin configuration constants for _configure() */
-#define HD64465_GPIO_FUNCTION2	0	/* use the pin's *other* function */
-#define HD64465_GPIO_OUT	1	/* output */
-#define HD64465_GPIO_IN_PULLUP	2	/* input, pull-up MOS on */
-#define HD64465_GPIO_IN		3	/* input */
-
-/* Configure a pin's direction */
-extern void hd64465_gpio_configure(int portpin, int direction);
-
-/* Get, set value */
-extern void hd64465_gpio_set_pin(int portpin, unsigned int value);
-extern unsigned int hd64465_gpio_get_pin(int portpin);
-extern void hd64465_gpio_set_port(int port, unsigned int value);
-extern unsigned int hd64465_gpio_get_port(int port);
-
-/* mode constants for _register_irq() */
-#define HD64465_GPIO_FALLING	0
-#define HD64465_GPIO_RISING	1
-
-/* Interrupt on external value change */
-extern void hd64465_gpio_register_irq(int portpin, int mode,
-	void (*handler)(int portpin, void *dev), void *dev);
-extern void hd64465_gpio_unregister_irq(int portpin);
-
-#endif /* _ASM_SH_HD64465_GPIO_  */
diff --git a/include/asm-sh/hd64465/hd64465.h b/include/asm-sh/hd64465/hd64465.h
deleted file mode 100644
index cfd0e803d2a2..000000000000
--- a/include/asm-sh/hd64465/hd64465.h
+++ /dev/null
@@ -1,256 +0,0 @@
-#ifndef _ASM_SH_HD64465_
-#define _ASM_SH_HD64465_ 1
-/*
- * $Id: hd64465.h,v 1.3 2003/05/04 19:30:15 lethal Exp $
- *
- * Hitachi HD64465 companion chip support
- *
- * by Greg Banks <gbanks@pocketpenguins.com>
- * (c) 2000 PocketPenguins Inc.
- *
- * Derived from <asm/hd64461.h> which bore the message:
- * Copyright (C) 2000 YAEGASHI Takeshi
- */
-#include <asm/io.h>
-#include <asm/irq.h>
-
-/*
- * Note that registers are defined here as virtual port numbers,
- * which have no meaning except to get translated by hd64465_isa_port2addr()
- * to an address in the range 0xb0000000-0xb3ffffff.  Note that
- * this translation happens to consist of adding the lower 16 bits
- * of the virtual port number to 0xb0000000.  Note also that the manual
- * shows addresses as absolute physical addresses starting at 0x10000000,
- * so e.g. the NIRR register is listed as 0x15000 here, 0x10005000 in the
- * manual, and accessed using address 0xb0005000 - Greg.
- */
-
-/* System registers */
-#define HD64465_REG_SRR     0x1000c 	/* System Revision Register */
-#define HD64465_REG_SDID    0x10010 	/* System Device ID Reg */
-#define     HD64465_SDID            0x8122  /* 64465 device ID */
-
-/* Power Management registers */
-#define HD64465_REG_SMSCR   0x10000 	/* System Module Standby Control Reg */
-#define	    HD64465_SMSCR_PS2ST     0x4000  /* PS/2 Standby */
-#define	    HD64465_SMSCR_ADCST     0x1000  /* ADC Standby */
-#define	    HD64465_SMSCR_UARTST    0x0800  /* UART Standby */
-#define	    HD64465_SMSCR_SCDIST    0x0200  /* Serial Codec Standby */
-#define	    HD64465_SMSCR_PPST	    0x0100  /* Parallel Port Standby */
-#define	    HD64465_SMSCR_PC0ST     0x0040  /* PCMCIA0 Standby */
-#define	    HD64465_SMSCR_PC1ST     0x0020  /* PCMCIA1 Standby */
-#define	    HD64465_SMSCR_AFEST     0x0010  /* AFE Standby */
-#define	    HD64465_SMSCR_TM0ST     0x0008  /* Timer0 Standby */
-#define	    HD64465_SMSCR_TM1ST     0x0004  /* Timer1 Standby */
-#define	    HD64465_SMSCR_IRDAST    0x0002  /* IRDA Standby */
-#define	    HD64465_SMSCR_KBCST     0x0001  /* Keyboard Controller Standby */
- 
-/* Interrupt Controller registers */
-#define HD64465_REG_NIRR    0x15000  	/* Interrupt Request Register */
-#define HD64465_REG_NIMR    0x15002  	/* Interrupt Mask Register */
-#define HD64465_REG_NITR    0x15004  	/* Interrupt Trigger Mode Register */
-
-/* Timer registers */
-#define HD64465_REG_TCVR1   0x16000  	/* Timer 1 constant value register  */
-#define HD64465_REG_TCVR0   0x16002	/* Timer 0 constant value register  */
-#define HD64465_REG_TRVR1   0x16004	/* Timer 1 read value register  */
-#define HD64465_REG_TRVR0   0x16006	/* Timer 0 read value register  */
-#define HD64465_REG_TCR1    0x16008	/* Timer 1 control register  */
-#define HD64465_REG_TCR0    0x1600A	/* Timer 0 control register  */
-#define	    HD64465_TCR_EADT 	0x10	    /* Enable ADTRIG# signal */
-#define	    HD64465_TCR_ETMO 	0x08	    /* Enable TMO signal */
-#define	    HD64465_TCR_PST_MASK 0x06	    /* Clock Prescale */
-#define	    HD64465_TCR_PST_1 	0x06	    /* 1:1 */
-#define	    HD64465_TCR_PST_4 	0x04	    /* 1:4 */
-#define	    HD64465_TCR_PST_8 	0x02	    /* 1:8 */
-#define	    HD64465_TCR_PST_16 	0x00	    /* 1:16 */
-#define	    HD64465_TCR_TSTP 	0x01	    /* Start/Stop timer */
-#define HD64465_REG_TIRR    0x1600C	/* Timer interrupt request register  */
-#define HD64465_REG_TIDR    0x1600E	/* Timer interrupt disable register  */
-#define HD64465_REG_PWM1CS  0x16010	/* PWM 1 clock scale register  */
-#define HD64465_REG_PWM1LPC 0x16012	/* PWM 1 low pulse width counter register  */
-#define HD64465_REG_PWM1HPC 0x16014	/* PWM 1 high pulse width counter register  */
-#define HD64465_REG_PWM0CS  0x16018	/* PWM 0 clock scale register  */
-#define HD64465_REG_PWM0LPC 0x1601A	/* PWM 0 low pulse width counter register  */
-#define HD64465_REG_PWM0HPC 0x1601C	/* PWM 0 high pulse width counter register  */
-
-/* Analog/Digital Converter registers */
-#define HD64465_REG_ADDRA   0x1E000	/* A/D data register A */
-#define HD64465_REG_ADDRB   0x1E002	/* A/D data register B */
-#define HD64465_REG_ADDRC   0x1E004	/* A/D data register C */
-#define HD64465_REG_ADDRD   0x1E006	/* A/D data register D */
-#define HD64465_REG_ADCSR   0x1E008	/* A/D control/status register */
-#define     HD64465_ADCSR_ADF	    0x80    /* A/D End Flag */
-#define     HD64465_ADCSR_ADST	    0x40    /* A/D Start Flag */
-#define     HD64465_ADCSR_ADIS	    0x20    /* A/D Interrupt Status */
-#define     HD64465_ADCSR_TRGE	    0x10    /* A/D Trigger Enable */
-#define     HD64465_ADCSR_ADIE	    0x08    /* A/D Interrupt Enable */
-#define     HD64465_ADCSR_SCAN	    0x04    /* A/D Scan Mode */
-#define     HD64465_ADCSR_CH_MASK   0x03    /* A/D Channel */
-#define HD64465_REG_ADCALCR 0x1E00A  	/* A/D calibration sample control */
-#define HD64465_REG_ADCAL   0x1E00C  	/* A/D calibration data register */
-
-
-/* General Purpose I/O ports registers */
-#define HD64465_REG_GPACR   0x14000  	/* Port A Control Register */
-#define HD64465_REG_GPBCR   0x14002  	/* Port B Control Register */
-#define HD64465_REG_GPCCR   0x14004  	/* Port C Control Register */
-#define HD64465_REG_GPDCR   0x14006  	/* Port D Control Register */
-#define HD64465_REG_GPECR   0x14008  	/* Port E Control Register */
-#define HD64465_REG_GPADR   0x14010  	/* Port A Data Register */
-#define HD64465_REG_GPBDR   0x14012  	/* Port B Data Register */
-#define HD64465_REG_GPCDR   0x14014  	/* Port C Data Register */
-#define HD64465_REG_GPDDR   0x14016  	/* Port D Data Register */
-#define HD64465_REG_GPEDR   0x14018  	/* Port E Data Register */
-#define HD64465_REG_GPAICR  0x14020  	/* Port A Interrupt Control Register */
-#define HD64465_REG_GPBICR  0x14022  	/* Port B Interrupt Control Register */
-#define HD64465_REG_GPCICR  0x14024  	/* Port C Interrupt Control Register */
-#define HD64465_REG_GPDICR  0x14026  	/* Port D Interrupt Control Register */
-#define HD64465_REG_GPEICR  0x14028  	/* Port E Interrupt Control Register */
-#define HD64465_REG_GPAISR  0x14040  	/* Port A Interrupt Status Register */
-#define HD64465_REG_GPBISR  0x14042  	/* Port B Interrupt Status Register */
-#define HD64465_REG_GPCISR  0x14044  	/* Port C Interrupt Status Register */
-#define HD64465_REG_GPDISR  0x14046  	/* Port D Interrupt Status Register */
-#define HD64465_REG_GPEISR  0x14048  	/* Port E Interrupt Status Register */
-
-/* PCMCIA bridge interface */
-#define HD64465_REG_PCC0ISR	0x12000	/* socket 0 interface status */ 
-#define     HD64465_PCCISR_PREADY   	 0x80    /* mem card ready / io card IREQ */
-#define     HD64465_PCCISR_PIREQ    	 0x80
-#define     HD64465_PCCISR_PMWP     	 0x40    /* mem card write-protected */
-#define     HD64465_PCCISR_PVS2 	 0x20    /* voltage select pin 2 */
-#define     HD64465_PCCISR_PVS1 	 0x10    /* voltage select pin 1 */
-#define     HD64465_PCCISR_PCD_MASK 	 0x0c    /* card detect */
-#define     HD64465_PCCISR_PBVD_MASK     0x03    /* battery voltage */
-#define     HD64465_PCCISR_PBVD_BATGOOD  0x03    /* battery good */
-#define     HD64465_PCCISR_PBVD_BATWARN  0x01    /* battery low warning */
-#define     HD64465_PCCISR_PBVD_BATDEAD1 0x02    /* battery dead */
-#define     HD64465_PCCISR_PBVD_BATDEAD2 0x00    /* battery dead */
-#define HD64465_REG_PCC0GCR	0x12002	/* socket 0 general control */ 
-#define     HD64465_PCCGCR_PDRV   	 0x80    /* output drive */
-#define     HD64465_PCCGCR_PCCR   	 0x40    /* PC card reset */
-#define     HD64465_PCCGCR_PCCT   	 0x20    /* PC card type, 1=IO&mem, 0=mem */
-#define     HD64465_PCCGCR_PVCC0   	 0x10    /* voltage control pin VCC0SEL0 */
-#define     HD64465_PCCGCR_PMMOD   	 0x08    /* memory mode */
-#define     HD64465_PCCGCR_PPA25   	 0x04    /* pin A25 */
-#define     HD64465_PCCGCR_PPA24   	 0x02    /* pin A24 */
-#define     HD64465_PCCGCR_PREG   	 0x01    /* ping PCC0REG# */
-#define HD64465_REG_PCC0CSCR	0x12004	/* socket 0 card status change */ 
-#define     HD64465_PCCCSCR_PSCDI   	 0x80    /* sw card detect intr */
-#define     HD64465_PCCCSCR_PSWSEL   	 0x40    /* power select */
-#define     HD64465_PCCCSCR_PIREQ   	 0x20    /* IREQ intr req */
-#define     HD64465_PCCCSCR_PSC   	 0x10    /* STSCHG (status change) pin */
-#define     HD64465_PCCCSCR_PCDC   	 0x08    /* CD (card detect) change */
-#define     HD64465_PCCCSCR_PRC   	 0x04    /* ready change */
-#define     HD64465_PCCCSCR_PBW   	 0x02    /* battery warning change */
-#define     HD64465_PCCCSCR_PBD   	 0x01    /* battery dead change */
-#define HD64465_REG_PCC0CSCIER	0x12006	/* socket 0 card status change interrupt enable */ 
-#define     HD64465_PCCCSCIER_PCRE   	 0x80    /* change reset enable */
-#define     HD64465_PCCCSCIER_PIREQE_MASK   	0x60   /* IREQ enable */
-#define     HD64465_PCCCSCIER_PIREQE_DISABLED	0x00   /* IREQ disabled */
-#define     HD64465_PCCCSCIER_PIREQE_LEVEL  	0x20   /* IREQ level-triggered */
-#define     HD64465_PCCCSCIER_PIREQE_FALLING	0x40   /* IREQ falling-edge-trig */
-#define     HD64465_PCCCSCIER_PIREQE_RISING 	0x60   /* IREQ rising-edge-trig */
-#define     HD64465_PCCCSCIER_PSCE   	 0x10    /* status change enable */
-#define     HD64465_PCCCSCIER_PCDE   	 0x08    /* card detect change enable */
-#define     HD64465_PCCCSCIER_PRE   	 0x04    /* ready change enable */
-#define     HD64465_PCCCSCIER_PBWE   	 0x02    /* battery warn change enable */
-#define     HD64465_PCCCSCIER_PBDE   	 0x01    /* battery dead change enable*/
-#define HD64465_REG_PCC0SCR	0x12008	/* socket 0 software control */ 
-#define     HD64465_PCCSCR_SHDN   	 0x10    /* TPS2206 SHutDowN pin */
-#define     HD64465_PCCSCR_SWP   	 0x01    /* write protect */
-#define HD64465_REG_PCCPSR	0x1200A	/* serial power switch control */ 
-#define HD64465_REG_PCC1ISR	0x12010	/* socket 1 interface status */ 
-#define HD64465_REG_PCC1GCR	0x12012	/* socket 1 general control */ 
-#define HD64465_REG_PCC1CSCR	0x12014	/* socket 1 card status change */ 
-#define HD64465_REG_PCC1CSCIER	0x12016	/* socket 1 card status change interrupt enable */ 
-#define HD64465_REG_PCC1SCR	0x12018	/* socket 1 software control */ 
-
-
-/* PS/2 Keyboard and mouse controller -- *not* register compatible */
-#define HD64465_REG_KBCSR   	0x1dc00 /* Keyboard Control/Status reg */
-#define     HD64465_KBCSR_KBCIE   	 0x8000    /* KBCK Input Enable */
-#define     HD64465_KBCSR_KBCOE   	 0x4000    /* KBCK Output Enable */
-#define     HD64465_KBCSR_KBDOE   	 0x2000    /* KB DATA Output Enable */
-#define     HD64465_KBCSR_KBCD   	 0x1000    /* KBCK Driven */
-#define     HD64465_KBCSR_KBDD   	 0x0800    /* KB DATA Driven */
-#define     HD64465_KBCSR_KBCS   	 0x0400    /* KBCK pin Status */
-#define     HD64465_KBCSR_KBDS   	 0x0200    /* KB DATA pin Status */
-#define     HD64465_KBCSR_KBDP   	 0x0100    /* KB DATA Parity bit */
-#define     HD64465_KBCSR_KBD_MASK   	 0x00ff    /* KD DATA shift reg */
-#define HD64465_REG_KBISR   	0x1dc04 /* Keyboard Interrupt Status reg */
-#define     HD64465_KBISR_KBRDF   	 0x0001    /* KB Received Data Full */
-#define HD64465_REG_MSCSR   	0x1dc10 /* Mouse Control/Status reg */
-#define HD64465_REG_MSISR   	0x1dc14 /* Mouse Interrupt Status reg */
-
-
-/*
- * Logical address at which the HD64465 is mapped.  Note that this
- * should always be in the P2 segment (uncached and untranslated).
- */
-#ifndef CONFIG_HD64465_IOBASE
-#define CONFIG_HD64465_IOBASE	0xb0000000
-#endif
-/*
- * The HD64465 multiplexes all its modules' interrupts onto
- * this single interrupt.
- */
-#ifndef CONFIG_HD64465_IRQ
-#define CONFIG_HD64465_IRQ	5
-#endif
-
-
-#define _HD64465_IO_MASK	0xf8000000
-#define is_hd64465_addr(addr) \
-	((addr & _HD64465_IO_MASK) == (CONFIG_HD64465_IOBASE & _HD64465_IO_MASK))
-
-/*
- * A range of 16 virtual interrupts generated by
- * demuxing the HD64465 muxed interrupt.
- */
-#define HD64465_IRQ_BASE	OFFCHIP_IRQ_BASE
-#define HD64465_IRQ_NUM 	16
-#define HD64465_IRQ_ADC     	(HD64465_IRQ_BASE+0)
-#define HD64465_IRQ_USB     	(HD64465_IRQ_BASE+1)
-#define HD64465_IRQ_SCDI    	(HD64465_IRQ_BASE+2)
-#define HD64465_IRQ_PARALLEL	(HD64465_IRQ_BASE+3)
-/* bit 4 is reserved */
-#define HD64465_IRQ_UART    	(HD64465_IRQ_BASE+5)
-#define HD64465_IRQ_IRDA    	(HD64465_IRQ_BASE+6)
-#define HD64465_IRQ_PS2MOUSE	(HD64465_IRQ_BASE+7)
-#define HD64465_IRQ_KBC     	(HD64465_IRQ_BASE+8)
-#define HD64465_IRQ_TIMER1   	(HD64465_IRQ_BASE+9)
-#define HD64465_IRQ_TIMER0  	(HD64465_IRQ_BASE+10)
-#define HD64465_IRQ_GPIO    	(HD64465_IRQ_BASE+11)
-#define HD64465_IRQ_AFE     	(HD64465_IRQ_BASE+12)
-#define HD64465_IRQ_PCMCIA1 	(HD64465_IRQ_BASE+13)
-#define HD64465_IRQ_PCMCIA0 	(HD64465_IRQ_BASE+14)
-#define HD64465_IRQ_PS2KBD     	(HD64465_IRQ_BASE+15)
-
-/* Constants for PCMCIA mappings */
-#define HD64465_PCC_WINDOW	0x01000000
-
-#define HD64465_PCC0_BASE	0xb8000000	/* area 6 */
-#define HD64465_PCC0_ATTR	(HD64465_PCC0_BASE)
-#define HD64465_PCC0_COMM	(HD64465_PCC0_BASE+HD64465_PCC_WINDOW)
-#define HD64465_PCC0_IO		(HD64465_PCC0_BASE+2*HD64465_PCC_WINDOW)
-
-#define HD64465_PCC1_BASE	0xb4000000	/* area 5 */
-#define HD64465_PCC1_ATTR	(HD64465_PCC1_BASE)
-#define HD64465_PCC1_COMM	(HD64465_PCC1_BASE+HD64465_PCC_WINDOW)
-#define HD64465_PCC1_IO		(HD64465_PCC1_BASE+2*HD64465_PCC_WINDOW)
-
-/*
- * Base of USB controller interface (as memory)
- */
-#define HD64465_USB_BASE    	(CONFIG_HD64465_IOBASE+0xb000)
-#define HD64465_USB_LEN    	0x1000
-/*
- * Base of embedded SRAM, used for USB controller.
- */
-#define HD64465_SRAM_BASE    	(CONFIG_HD64465_IOBASE+0x9000)
-#define HD64465_SRAM_LEN    	0x1000
-
-
-
-#endif /* _ASM_SH_HD64465_  */
diff --git a/include/asm-sh/hd64465/io.h b/include/asm-sh/hd64465/io.h
deleted file mode 100644
index 139f1472e5bb..000000000000
--- a/include/asm-sh/hd64465/io.h
+++ /dev/null
@@ -1,44 +0,0 @@
-/*
- * include/asm-sh/hd64465/io.h
- *
- * By Greg Banks <gbanks@pocketpenguins.com>
- * (c) 2000 PocketPenguins Inc.
- *
- * Derived from io_hd64461.h, which bore the message:
- * Copyright 2000 Stuart Menefy (stuart.menefy@st.com)
- *
- * May be copied or modified under the terms of the GNU General Public
- * License.  See linux/COPYING for more information.
- *
- * IO functions for an HD64465 "Windows CE Intelligent Peripheral Controller".
- */
-
-#ifndef _ASM_SH_IO_HD64465_H
-#define _ASM_SH_IO_HD64465_H
-
-extern unsigned char hd64465_inb(unsigned long port);
-extern unsigned short hd64465_inw(unsigned long port);
-extern unsigned int hd64465_inl(unsigned long port);
-
-extern void hd64465_outb(unsigned char value, unsigned long port);
-extern void hd64465_outw(unsigned short value, unsigned long port);
-extern void hd64465_outl(unsigned int value, unsigned long port);
-
-extern unsigned char hd64465_inb_p(unsigned long port);
-extern void hd64465_outb_p(unsigned char value, unsigned long port);
-
-extern unsigned long hd64465_isa_port2addr(unsigned long offset);
-extern int hd64465_irq_demux(int irq);
-/* Provision for generic secondary demux step -- used by PCMCIA code */
-extern void hd64465_register_irq_demux(int irq,
-		int (*demux)(int irq, void *dev), void *dev);
-extern void hd64465_unregister_irq_demux(int irq);
-/* Set this variable to 1 to see port traffic */
-extern int hd64465_io_debug;
-/* Map a range of ports to a range of kernel virtual memory.
- */
-extern void hd64465_port_map(unsigned short baseport, unsigned int nports,
-			     unsigned long addr, unsigned char shift);
-extern void hd64465_port_unmap(unsigned short baseport, unsigned int nports);
-
-#endif /* _ASM_SH_IO_HD64465_H */