Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6

3 files changed, 109 insertions, 4 deletions

diff --git a/include/linux/ieee80211.h b/include/linux/ieee80211.h
index 163c840437d6..d62edc7df3ae 100644
--- a/include/linux/ieee80211.h
+++ b/include/linux/ieee80211.h
@@ -707,6 +707,10 @@ struct ieee80211_mgmt {
 					u8 action;
 					u8 trans_id[WLAN_SA_QUERY_TR_ID_LEN];
 				} __attribute__ ((packed)) sa_query;
+				struct {
+					u8 action;
+					u8 smps_control;
+				} __attribute__ ((packed)) ht_smps;
 			} u;
 		} __attribute__ ((packed)) action;
 	} u;
@@ -771,7 +775,10 @@ struct ieee80211_bar {
 /**
  * struct ieee80211_mcs_info - MCS information
  * @rx_mask: RX mask
- * @rx_highest: highest supported RX rate
+ * @rx_highest: highest supported RX rate. If set represents
+ *	the highest supported RX data rate in units of 1 Mbps.
+ *	If this field is 0 this value should not be used to
+ *	consider the highest RX data rate supported.
  * @tx_params: TX parameters
  */
 struct ieee80211_mcs_info {
@@ -824,6 +831,7 @@ struct ieee80211_ht_cap {
 #define IEEE80211_HT_CAP_LDPC_CODING		0x0001
 #define IEEE80211_HT_CAP_SUP_WIDTH_20_40	0x0002
 #define IEEE80211_HT_CAP_SM_PS			0x000C
+#define		IEEE80211_HT_CAP_SM_PS_SHIFT	2
 #define IEEE80211_HT_CAP_GRN_FLD		0x0010
 #define IEEE80211_HT_CAP_SGI_20			0x0020
 #define IEEE80211_HT_CAP_SGI_40			0x0040
@@ -839,6 +847,7 @@ struct ieee80211_ht_cap {
 /* 802.11n HT capability AMPDU settings (for ampdu_params_info) */
 #define IEEE80211_HT_AMPDU_PARM_FACTOR		0x03
 #define IEEE80211_HT_AMPDU_PARM_DENSITY		0x1C
+#define		IEEE80211_HT_AMPDU_PARM_DENSITY_SHIFT	2
 
 /*
  * Maximum length of AMPDU that the STA can receive.
@@ -922,12 +931,17 @@ struct ieee80211_ht_info {
 #define IEEE80211_MAX_AMPDU_BUF 0x40
 
 
-/* Spatial Multiplexing Power Save Modes */
+/* Spatial Multiplexing Power Save Modes (for capability) */
 #define WLAN_HT_CAP_SM_PS_STATIC	0
 #define WLAN_HT_CAP_SM_PS_DYNAMIC	1
 #define WLAN_HT_CAP_SM_PS_INVALID	2
 #define WLAN_HT_CAP_SM_PS_DISABLED	3
 
+/* for SM power control field lower two bits */
+#define WLAN_HT_SMPS_CONTROL_DISABLED	0
+#define WLAN_HT_SMPS_CONTROL_STATIC	1
+#define WLAN_HT_SMPS_CONTROL_DYNAMIC	3
+
 /* Authentication algorithms */
 #define WLAN_AUTH_OPEN 0
 #define WLAN_AUTH_SHARED_KEY 1
@@ -1150,6 +1164,18 @@ enum ieee80211_spectrum_mgmt_actioncode {
 	WLAN_ACTION_SPCT_CHL_SWITCH = 4,
 };
 
+/* HT action codes */
+enum ieee80211_ht_actioncode {
+	WLAN_HT_ACTION_NOTIFY_CHANWIDTH = 0,
+	WLAN_HT_ACTION_SMPS = 1,
+	WLAN_HT_ACTION_PSMP = 2,
+	WLAN_HT_ACTION_PCO_PHASE = 3,
+	WLAN_HT_ACTION_CSI = 4,
+	WLAN_HT_ACTION_NONCOMPRESSED_BF = 5,
+	WLAN_HT_ACTION_COMPRESSED_BF = 6,
+	WLAN_HT_ACTION_ASEL_IDX_FEEDBACK = 7,
+};
+
 /* Security key length */
 enum ieee80211_key_len {
 	WLAN_KEY_LEN_WEP40 = 5,
diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index 0884b9a0f778..542a477a94da 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -1578,7 +1578,7 @@ unsigned int ieee80211_hdrlen(__le16 fc);
  * @addr: the device MAC address
  * @iftype: the virtual interface type
  */
-int ieee80211_data_to_8023(struct sk_buff *skb, u8 *addr,
+int ieee80211_data_to_8023(struct sk_buff *skb, const u8 *addr,
 			   enum nl80211_iftype iftype);
 
 /**
@@ -1589,10 +1589,28 @@ int ieee80211_data_to_8023(struct sk_buff *skb, u8 *addr,
  * @bssid: the network bssid (used only for iftype STATION and ADHOC)
  * @qos: build 802.11 QoS data frame
  */
-int ieee80211_data_from_8023(struct sk_buff *skb, u8 *addr,
+int ieee80211_data_from_8023(struct sk_buff *skb, const u8 *addr,
 			     enum nl80211_iftype iftype, u8 *bssid, bool qos);
 
 /**
+ * ieee80211_amsdu_to_8023s - decode an IEEE 802.11n A-MSDU frame
+ *
+ * Decode an IEEE 802.11n A-MSDU frame and convert it to a list of
+ * 802.3 frames. The @list will be empty if the decode fails. The
+ * @skb is consumed after the function returns.
+ *
+ * @skb: The input IEEE 802.11n A-MSDU frame.
+ * @list: The output list of 802.3 frames. It must be allocated and
+ *	initialized by by the caller.
+ * @addr: The device MAC address.
+ * @iftype: The device interface type.
+ * @extra_headroom: The hardware extra headroom for SKBs in the @list.
+ */
+void ieee80211_amsdu_to_8023s(struct sk_buff *skb, struct sk_buff_head *list,
+			      const u8 *addr, enum nl80211_iftype iftype,
+			      const unsigned int extra_headroom);
+
+/**
  * cfg80211_classify8021d - determine the 802.1p/1d tag for a data frame
  * @skb: the data frame
  */
diff --git a/include/net/mac80211.h b/include/net/mac80211.h
index 538d6b761887..494ac69ff477 100644
--- a/include/net/mac80211.h
+++ b/include/net/mac80211.h
@@ -597,8 +597,10 @@ enum ieee80211_conf_flags {
  * @IEEE80211_CONF_CHANGE_CHANNEL: the channel/channel_type changed
  * @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed
  * @IEEE80211_CONF_CHANGE_IDLE: Idle flag changed
+ * @IEEE80211_CONF_CHANGE_SMPS: Spatial multiplexing powersave mode changed
  */
 enum ieee80211_conf_changed {
+	IEEE80211_CONF_CHANGE_SMPS		= BIT(1),
 	IEEE80211_CONF_CHANGE_LISTEN_INTERVAL	= BIT(2),
 	IEEE80211_CONF_CHANGE_MONITOR		= BIT(3),
 	IEEE80211_CONF_CHANGE_PS		= BIT(4),
@@ -609,6 +611,21 @@ enum ieee80211_conf_changed {
 };
 
 /**
+ * enum ieee80211_smps_mode - spatial multiplexing power save mode
+ *
+ * @
+ */
+enum ieee80211_smps_mode {
+	IEEE80211_SMPS_AUTOMATIC,
+	IEEE80211_SMPS_OFF,
+	IEEE80211_SMPS_STATIC,
+	IEEE80211_SMPS_DYNAMIC,
+
+	/* keep last */
+	IEEE80211_SMPS_NUM_MODES,
+};
+
+/**
  * struct ieee80211_conf - configuration of the device
  *
  * This struct indicates how the driver shall configure the hardware.
@@ -636,6 +653,10 @@ enum ieee80211_conf_changed {
  * @short_frame_max_tx_count: Maximum number of transmissions for a "short"
  *    frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
  *    number of transmissions not the number of retries
+ *
+ * @smps_mode: spatial multiplexing powersave mode; note that
+ *	%IEEE80211_SMPS_STATIC is used when the device is not
+ *	configured for an HT channel
  */
 struct ieee80211_conf {
 	u32 flags;
@@ -648,6 +669,7 @@ struct ieee80211_conf {
 
 	struct ieee80211_channel *channel;
 	enum nl80211_channel_type channel_type;
+	enum ieee80211_smps_mode smps_mode;
 };
 
 /**
@@ -659,12 +681,14 @@ struct ieee80211_conf {
  * @type: type of this virtual interface
  * @bss_conf: BSS configuration for this interface, either our own
  *	or the BSS we're associated to
+ * @addr: address of this interface
  * @drv_priv: data area for driver use, will always be aligned to
  *	sizeof(void *).
  */
 struct ieee80211_vif {
 	enum nl80211_iftype type;
 	struct ieee80211_bss_conf bss_conf;
+	u8 addr[ETH_ALEN];
 	/* must be last */
 	u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *))));
 };
@@ -928,6 +952,16 @@ enum ieee80211_tkip_key_type {
  * @IEEE80211_HW_BEACON_FILTER:
  *	Hardware supports dropping of irrelevant beacon frames to
  *	avoid waking up cpu.
+ *
+ * @IEEE80211_HW_SUPPORTS_STATIC_SMPS:
+ *	Hardware supports static spatial multiplexing powersave,
+ *	ie. can turn off all but one chain even on HT connections
+ *	that should be using more chains.
+ *
+ * @IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS:
+ *	Hardware supports dynamic spatial multiplexing powersave,
+ *	ie. can turn off all but one chain and then wake the rest
+ *	up as required after, for example, rts/cts handshake.
  */
 enum ieee80211_hw_flags {
 	IEEE80211_HW_HAS_RATE_CONTROL			= 1<<0,
@@ -945,6 +979,8 @@ enum ieee80211_hw_flags {
 	IEEE80211_HW_SUPPORTS_DYNAMIC_PS		= 1<<12,
 	IEEE80211_HW_MFP_CAPABLE			= 1<<13,
 	IEEE80211_HW_BEACON_FILTER			= 1<<14,
+	IEEE80211_HW_SUPPORTS_STATIC_SMPS		= 1<<15,
+	IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS		= 1<<16,
 };
 
 /**
@@ -1213,6 +1249,31 @@ ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw,
  */
 
 /**
+ * DOC: Spatial multiplexing power save
+ *
+ * SMPS (Spatial multiplexing power save) is a mechanism to conserve
+ * power in an 802.11n implementation. For details on the mechanism
+ * and rationale, please refer to 802.11 (as amended by 802.11n-2009)
+ * "11.2.3 SM power save".
+ *
+ * The mac80211 implementation is capable of sending action frames
+ * to update the AP about the station's SMPS mode, and will instruct
+ * the driver to enter the specific mode. It will also announce the
+ * requested SMPS mode during the association handshake. Hardware
+ * support for this feature is required, and can be indicated by
+ * hardware flags.
+ *
+ * The default mode will be "automatic", which nl80211/cfg80211
+ * defines to be dynamic SMPS in (regular) powersave, and SMPS
+ * turned off otherwise.
+ *
+ * To support this feature, the driver must set the appropriate
+ * hardware support flags, and handle the SMPS flag to the config()
+ * operation. It will then with this mechanism be instructed to
+ * enter the requested SMPS mode while associated to an HT AP.
+ */
+
+/**
  * DOC: Frame filtering
  *
  * mac80211 requires to see many management frames for proper