diff options
| -rw-r--r-- | Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt | 110 | ||||
| -rw-r--r-- | arch/arm/boot/dts/bcm2835.dtsi | 8 | ||||
| -rw-r--r-- | arch/arm/mach-bcm2835/bcm2835.c | 10 | ||||
| -rw-r--r-- | drivers/Kconfig | 2 | ||||
| -rw-r--r-- | drivers/Makefile | 2 | ||||
| -rw-r--r-- | drivers/irqchip/Kconfig | 0 | ||||
| -rw-r--r-- | drivers/irqchip/Makefile | 1 | ||||
| -rw-r--r-- | drivers/irqchip/irq-bcm2835.c | 223 | ||||
| -rw-r--r-- | include/linux/irqchip/bcm2835.h | 29 |
9 files changed, 376 insertions, 9 deletions
diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt new file mode 100644 index 000000000000..548892c08c59 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt @@ -0,0 +1,110 @@ +BCM2835 Top-Level ("ARMCTRL") Interrupt Controller + +The BCM2835 contains a custom top-level interrupt controller, which supports +72 interrupt sources using a 2-level register scheme. The interrupt +controller, or the HW block containing it, is referred to occasionally +as "armctrl" in the SoC documentation, hence naming of this binding. + +Required properties: + +- compatible : should be "brcm,bcm2835-armctrl-ic.txt" +- reg : Specifies base physical address and size of the registers. +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The value shall be 2. + + The 1st cell is the interrupt bank; 0 for interrupts in the "IRQ basic + pending" register, or 1/2 respectively for interrupts in the "IRQ pending + 1/2" register. + + The 2nd cell contains the interrupt number within the bank. Valid values + are 0..7 for bank 0, and 0..31 for bank 1. + +The interrupt sources are as follows: + +Bank 0: +0: ARM_TIMER +1: ARM_MAILBOX +2: ARM_DOORBELL_0 +3: ARM_DOORBELL_1 +4: VPU0_HALTED +5: VPU1_HALTED +6: ILLEGAL_TYPE0 +7: ILLEGAL_TYPE1 + +Bank 1: +0: TIMER0 +1: TIMER1 +2: TIMER2 +3: TIMER3 +4: CODEC0 +5: CODEC1 +6: CODEC2 +7: VC_JPEG +8: ISP +9: VC_USB +10: VC_3D +11: TRANSPOSER +12: MULTICORESYNC0 +13: MULTICORESYNC1 +14: MULTICORESYNC2 +15: MULTICORESYNC3 +16: DMA0 +17: DMA1 +18: VC_DMA2 +19: VC_DMA3 +20: DMA4 +21: DMA5 +22: DMA6 +23: DMA7 +24: DMA8 +25: DMA9 +26: DMA10 +27: DMA11 +28: DMA12 +29: AUX +30: ARM +31: VPUDMA + +Bank 2: +0: HOSTPORT +1: VIDEOSCALER +2: CCP2TX +3: SDC +4: DSI0 +5: AVE +6: CAM0 +7: CAM1 +8: HDMI0 +9: HDMI1 +10: PIXELVALVE1 +11: I2CSPISLV +12: DSI1 +13: PWA0 +14: PWA1 +15: CPR +16: SMI +17: GPIO0 +18: GPIO1 +19: GPIO2 +20: GPIO3 +21: VC_I2C +22: VC_SPI +23: VC_I2SPCM +24: VC_SDIO +25: VC_UART +26: SLIMBUS +27: VEC +28: CPG +29: RNG +30: VC_ARASANSDIO +31: AVSPMON + +Example: + +intc: interrupt-controller { + compatible = "brcm,bcm2835-armctrl-ic"; + reg = <0x7e00b200 0x200>; + interrupt-controller; + #interrupt-cells = <2>; +}; diff --git a/arch/arm/boot/dts/bcm2835.dtsi b/arch/arm/boot/dts/bcm2835.dtsi index a31cb40ef684..8842d751d7dd 100644 --- a/arch/arm/boot/dts/bcm2835.dtsi +++ b/arch/arm/boot/dts/bcm2835.dtsi @@ -3,6 +3,7 @@ / { compatible = "brcm,bcm2835"; model = "BCM2835"; + interrupt-parent = <&intc>; chosen { bootargs = "earlyprintk"; @@ -13,5 +14,12 @@ #address-cells = <1>; #size-cells = <1>; ranges = <0x7e000000 0x20000000 0x02000000>; + + intc: interrupt-controller { + compatible = "brcm,bcm2835-armctrl-ic"; + reg = <0x7e00b200 0x200>; + interrupt-controller; + #interrupt-cells = <2>; + }; }; }; diff --git a/arch/arm/mach-bcm2835/bcm2835.c b/arch/arm/mach-bcm2835/bcm2835.c index f6b36b4b5921..72c4b5ff8f90 100644 --- a/arch/arm/mach-bcm2835/bcm2835.c +++ b/arch/arm/mach-bcm2835/bcm2835.c @@ -13,12 +13,12 @@ */ #include <linux/init.h> +#include <linux/irqchip/bcm2835.h> #include <linux/of_platform.h> #include <asm/mach/arch.h> #include <asm/mach/map.h> #include <asm/mach/time.h> -#include <asm/exception.h> #include <mach/bcm2835_soc.h> @@ -34,14 +34,6 @@ void __init bcm2835_map_io(void) iotable_init(&io_map, 1); } -void __init bcm2835_init_irq(void) -{ -} - -asmlinkage void __exception_irq_entry bcm2835_handle_irq(struct pt_regs *regs) -{ -} - void __init bcm2835_init(void) { int ret; diff --git a/drivers/Kconfig b/drivers/Kconfig index ece958d3762e..36d3daa19a74 100644 --- a/drivers/Kconfig +++ b/drivers/Kconfig @@ -152,4 +152,6 @@ source "drivers/vme/Kconfig" source "drivers/pwm/Kconfig" +source "drivers/irqchip/Kconfig" + endmenu diff --git a/drivers/Makefile b/drivers/Makefile index 5b421840c48d..8c30e73cd94c 100644 --- a/drivers/Makefile +++ b/drivers/Makefile @@ -5,6 +5,8 @@ # Rewritten to use lists instead of if-statements. # +obj-y += irqchip/ + # GPIO must come after pinctrl as gpios may need to mux pins etc obj-y += pinctrl/ obj-y += gpio/ diff --git a/drivers/irqchip/Kconfig b/drivers/irqchip/Kconfig new file mode 100644 index 000000000000..e69de29bb2d1 --- /dev/null +++ b/drivers/irqchip/Kconfig diff --git a/drivers/irqchip/Makefile b/drivers/irqchip/Makefile new file mode 100644 index 000000000000..054321db4350 --- /dev/null +++ b/drivers/irqchip/Makefile @@ -0,0 +1 @@ +obj-$(CONFIG_ARCH_BCM2835) += irq-bcm2835.o diff --git a/drivers/irqchip/irq-bcm2835.c b/drivers/irqchip/irq-bcm2835.c new file mode 100644 index 000000000000..dc670ccc6978 --- /dev/null +++ b/drivers/irqchip/irq-bcm2835.c @@ -0,0 +1,223 @@ +/* + * Copyright 2010 Broadcom + * Copyright 2012 Simon Arlott, Chris Boot, Stephen Warren + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Quirk 1: Shortcut interrupts don't set the bank 1/2 register pending bits + * + * If an interrupt fires on bank 1 that isn't in the shortcuts list, bit 8 + * on bank 0 is set to signify that an interrupt in bank 1 has fired, and + * to look in the bank 1 status register for more information. + * + * If an interrupt fires on bank 1 that _is_ in the shortcuts list, its + * shortcut bit in bank 0 is set as well as its interrupt bit in the bank 1 + * status register, but bank 0 bit 8 is _not_ set. + * + * Quirk 2: You can't mask the register 1/2 pending interrupts + * + * In a proper cascaded interrupt controller, the interrupt lines with + * cascaded interrupt controllers on them are just normal interrupt lines. + * You can mask the interrupts and get on with things. With this controller + * you can't do that. + * + * Quirk 3: The shortcut interrupts can't be (un)masked in bank 0 + * + * Those interrupts that have shortcuts can only be masked/unmasked in + * their respective banks' enable/disable registers. Doing so in the bank 0 + * enable/disable registers has no effect. + * + * The FIQ control register: + * Bits 0-6: IRQ (index in order of interrupts from banks 1, 2, then 0) + * Bit 7: Enable FIQ generation + * Bits 8+: Unused + * + * An interrupt must be disabled before configuring it for FIQ generation + * otherwise both handlers will fire at the same time! + */ + +#include <linux/io.h> +#include <linux/slab.h> +#include <linux/of_address.h> +#include <linux/of_irq.h> +#include <linux/irqdomain.h> +#include <linux/irqchip/bcm2835.h> + +#include <asm/exception.h> + +/* Put the bank and irq (32 bits) into the hwirq */ +#define MAKE_HWIRQ(b, n) ((b << 5) | (n)) +#define HWIRQ_BANK(i) (i >> 5) +#define HWIRQ_BIT(i) BIT(i & 0x1f) + +#define NR_IRQS_BANK0 8 +#define BANK0_HWIRQ_MASK 0xff +/* Shortcuts can't be disabled so any unknown new ones need to be masked */ +#define SHORTCUT1_MASK 0x00007c00 +#define SHORTCUT2_MASK 0x001f8000 +#define SHORTCUT_SHIFT 10 +#define BANK1_HWIRQ BIT(8) +#define BANK2_HWIRQ BIT(9) +#define BANK0_VALID_MASK (BANK0_HWIRQ_MASK | BANK1_HWIRQ | BANK2_HWIRQ \ + | SHORTCUT1_MASK | SHORTCUT2_MASK) + +#define REG_FIQ_CONTROL 0x0c + +#define NR_BANKS 3 +#define IRQS_PER_BANK 32 + +static int reg_pending[] __initconst = { 0x00, 0x04, 0x08 }; +static int reg_enable[] __initconst = { 0x18, 0x10, 0x14 }; +static int reg_disable[] __initconst = { 0x24, 0x1c, 0x20 }; +static int bank_irqs[] __initconst = { 8, 32, 32 }; + +static const int shortcuts[] = { + 7, 9, 10, 18, 19, /* Bank 1 */ + 21, 22, 23, 24, 25, 30 /* Bank 2 */ +}; + +struct armctrl_ic { + void __iomem *base; + void __iomem *pending[NR_BANKS]; + void __iomem *enable[NR_BANKS]; + void __iomem *disable[NR_BANKS]; + struct irq_domain *domain; +}; + +static struct armctrl_ic intc __read_mostly; + +static void armctrl_mask_irq(struct irq_data *d) +{ + writel_relaxed(HWIRQ_BIT(d->hwirq), intc.disable[HWIRQ_BANK(d->hwirq)]); +} + +static void armctrl_unmask_irq(struct irq_data *d) +{ + writel_relaxed(HWIRQ_BIT(d->hwirq), intc.enable[HWIRQ_BANK(d->hwirq)]); +} + +static struct irq_chip armctrl_chip = { + .name = "ARMCTRL-level", + .irq_mask = armctrl_mask_irq, + .irq_unmask = armctrl_unmask_irq +}; + +static int armctrl_xlate(struct irq_domain *d, struct device_node *ctrlr, + const u32 *intspec, unsigned int intsize, + unsigned long *out_hwirq, unsigned int *out_type) +{ + if (WARN_ON(intsize != 2)) + return -EINVAL; + + if (WARN_ON(intspec[0] >= NR_BANKS)) + return -EINVAL; + + if (WARN_ON(intspec[1] >= IRQS_PER_BANK)) + return -EINVAL; + + if (WARN_ON(intspec[0] == 0 && intspec[1] >= NR_IRQS_BANK0)) + return -EINVAL; + + *out_hwirq = MAKE_HWIRQ(intspec[0], intspec[1]); + *out_type = IRQ_TYPE_NONE; + return 0; +} + +static struct irq_domain_ops armctrl_ops = { + .xlate = armctrl_xlate +}; + +static int __init armctrl_of_init(struct device_node *node, + struct device_node *parent) +{ + void __iomem *base; + int irq, b, i; + + base = of_iomap(node, 0); + if (!base) + panic("%s: unable to map IC registers\n", + node->full_name); + + intc.domain = irq_domain_add_linear(node, MAKE_HWIRQ(NR_BANKS, 0), + &armctrl_ops, NULL); + if (!intc.domain) + panic("%s: unable to create IRQ domain\n", node->full_name); + + for (b = 0; b < NR_BANKS; b++) { + intc.pending[b] = base + reg_pending[b]; + intc.enable[b] = base + reg_enable[b]; + intc.disable[b] = base + reg_disable[b]; + + for (i = 0; i < bank_irqs[b]; i++) { + irq = irq_create_mapping(intc.domain, MAKE_HWIRQ(b, i)); + BUG_ON(irq <= 0); + irq_set_chip_and_handler(irq, &armctrl_chip, + handle_level_irq); + set_irq_flags(irq, IRQF_VALID | IRQF_PROBE); + } + } + return 0; +} + +static struct of_device_id irq_of_match[] __initconst = { + { .compatible = "brcm,bcm2835-armctrl-ic", .data = armctrl_of_init } +}; + +void __init bcm2835_init_irq(void) +{ + of_irq_init(irq_of_match); +} + +/* + * Handle each interrupt across the entire interrupt controller. This reads the + * status register before handling each interrupt, which is necessary given that + * handle_IRQ may briefly re-enable interrupts for soft IRQ handling. + */ + +static void armctrl_handle_bank(int bank, struct pt_regs *regs) +{ + u32 stat, irq; + + while ((stat = readl_relaxed(intc.pending[bank]))) { + irq = MAKE_HWIRQ(bank, ffs(stat) - 1); + handle_IRQ(irq_linear_revmap(intc.domain, irq), regs); + } +} + +static void armctrl_handle_shortcut(int bank, struct pt_regs *regs, + u32 stat) +{ + u32 irq = MAKE_HWIRQ(bank, shortcuts[ffs(stat >> SHORTCUT_SHIFT) - 1]); + handle_IRQ(irq_linear_revmap(intc.domain, irq), regs); +} + +asmlinkage void __exception_irq_entry bcm2835_handle_irq( + struct pt_regs *regs) +{ + u32 stat, irq; + + while ((stat = readl_relaxed(intc.pending[0]) & BANK0_VALID_MASK)) { + if (stat & BANK0_HWIRQ_MASK) { + irq = MAKE_HWIRQ(0, ffs(stat & BANK0_HWIRQ_MASK) - 1); + handle_IRQ(irq_linear_revmap(intc.domain, irq), regs); + } else if (stat & SHORTCUT1_MASK) { + armctrl_handle_shortcut(1, regs, stat & SHORTCUT1_MASK); + } else if (stat & SHORTCUT2_MASK) { + armctrl_handle_shortcut(2, regs, stat & SHORTCUT2_MASK); + } else if (stat & BANK1_HWIRQ) { + armctrl_handle_bank(1, regs); + } else if (stat & BANK2_HWIRQ) { + armctrl_handle_bank(2, regs); + } else { + BUG(); + } + } +} diff --git a/include/linux/irqchip/bcm2835.h b/include/linux/irqchip/bcm2835.h new file mode 100644 index 000000000000..48a859bc9dca --- /dev/null +++ b/include/linux/irqchip/bcm2835.h @@ -0,0 +1,29 @@ +/* + * Copyright (C) 2010 Broadcom + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#ifndef __LINUX_IRQCHIP_BCM2835_H_ +#define __LINUX_IRQCHIP_BCM2835_H_ + +#include <asm/exception.h> + +extern void bcm2835_init_irq(void); + +extern asmlinkage void __exception_irq_entry bcm2835_handle_irq( + struct pt_regs *regs); + +#endif |