diff options
| -rw-r--r-- | arch/powerpc/kernel/entry_32.S | 6 | ||||
| -rw-r--r-- | arch/powerpc/kernel/process.c | 46 | ||||
| -rw-r--r-- | arch/powerpc/kernel/ptrace.c | 72 | ||||
| -rw-r--r-- | arch/powerpc/kernel/signal.c | 6 | ||||
| -rw-r--r-- | arch/powerpc/kernel/traps.c | 16 | ||||
| -rw-r--r-- | arch/powerpc/mm/fault.c | 25 | ||||
| -rw-r--r-- | include/asm-powerpc/system.h | 2 |
7 files changed, 138 insertions, 35 deletions
diff --git a/arch/powerpc/kernel/entry_32.S b/arch/powerpc/kernel/entry_32.S index da52269aec1e..81c8324a4a3c 100644 --- a/arch/powerpc/kernel/entry_32.S +++ b/arch/powerpc/kernel/entry_32.S @@ -148,7 +148,7 @@ transfer_to_handler: /* Check to see if the dbcr0 register is set up to debug. Use the internal debug mode bit to do this. */ lwz r12,THREAD_DBCR0(r12) - andis. r12,r12,DBCR0_IDM@h + andis. r12,r12,(DBCR0_IDM | DBSR_DAC1R | DBSR_DAC1W)@h beq+ 3f /* From user and task is ptraced - load up global dbcr0 */ li r12,-1 /* clear all pending debug events */ @@ -292,7 +292,7 @@ syscall_exit_cont: /* If the process has its own DBCR0 value, load it up. The internal debug mode bit tells us that dbcr0 should be loaded. */ lwz r0,THREAD+THREAD_DBCR0(r2) - andis. r10,r0,DBCR0_IDM@h + andis. r10,r0,(DBCR0_IDM | DBSR_DAC1R | DBSR_DAC1W)@h bnel- load_dbcr0 #endif #ifdef CONFIG_44x @@ -720,7 +720,7 @@ restore_user: /* Check whether this process has its own DBCR0 value. The internal debug mode bit tells us that dbcr0 should be loaded. */ lwz r0,THREAD+THREAD_DBCR0(r2) - andis. r10,r0,DBCR0_IDM@h + andis. r10,r0,(DBCR0_IDM | DBSR_DAC1R | DBSR_DAC1W)@h bnel- load_dbcr0 #endif diff --git a/arch/powerpc/kernel/process.c b/arch/powerpc/kernel/process.c index 219f3634115e..db2497ccc111 100644 --- a/arch/powerpc/kernel/process.c +++ b/arch/powerpc/kernel/process.c @@ -47,6 +47,8 @@ #ifdef CONFIG_PPC64 #include <asm/firmware.h> #endif +#include <linux/kprobes.h> +#include <linux/kdebug.h> extern unsigned long _get_SP(void); @@ -239,6 +241,35 @@ void discard_lazy_cpu_state(void) } #endif /* CONFIG_SMP */ +void do_dabr(struct pt_regs *regs, unsigned long address, + unsigned long error_code) +{ + siginfo_t info; + + if (notify_die(DIE_DABR_MATCH, "dabr_match", regs, error_code, + 11, SIGSEGV) == NOTIFY_STOP) + return; + + if (debugger_dabr_match(regs)) + return; + + /* Clear the DAC and struct entries. One shot trigger */ +#if (defined(CONFIG_44x) || defined(CONFIG_BOOKE)) + mtspr(SPRN_DBCR0, mfspr(SPRN_DBCR0) & ~(DBSR_DAC1R | DBSR_DAC1W + | DBCR0_IDM)); +#endif + + /* Clear the DABR */ + set_dabr(0); + + /* Deliver the signal to userspace */ + info.si_signo = SIGTRAP; + info.si_errno = 0; + info.si_code = TRAP_HWBKPT; + info.si_addr = (void __user *)address; + force_sig_info(SIGTRAP, &info, current); +} + static DEFINE_PER_CPU(unsigned long, current_dabr); int set_dabr(unsigned long dabr) @@ -254,6 +285,11 @@ int set_dabr(unsigned long dabr) #if defined(CONFIG_PPC64) || defined(CONFIG_6xx) mtspr(SPRN_DABR, dabr); #endif + +#if defined(CONFIG_44x) || defined(CONFIG_BOOKE) + mtspr(SPRN_DAC1, dabr); +#endif + return 0; } @@ -337,6 +373,12 @@ struct task_struct *__switch_to(struct task_struct *prev, if (unlikely(__get_cpu_var(current_dabr) != new->thread.dabr)) set_dabr(new->thread.dabr); +#if defined(CONFIG_44x) || defined(CONFIG_BOOKE) + /* If new thread DAC (HW breakpoint) is the same then leave it */ + if (new->thread.dabr) + set_dabr(new->thread.dabr); +#endif + new_thread = &new->thread; old_thread = ¤t->thread; @@ -525,6 +567,10 @@ void flush_thread(void) if (current->thread.dabr) { current->thread.dabr = 0; set_dabr(0); + +#if defined(CONFIG_44x) || defined(CONFIG_BOOKE) + current->thread.dbcr0 &= ~(DBSR_DAC1R | DBSR_DAC1W); +#endif } } diff --git a/arch/powerpc/kernel/ptrace.c b/arch/powerpc/kernel/ptrace.c index 8feb93e7890c..a5d0e78779c8 100644 --- a/arch/powerpc/kernel/ptrace.c +++ b/arch/powerpc/kernel/ptrace.c @@ -703,7 +703,7 @@ void user_enable_single_step(struct task_struct *task) if (regs != NULL) { #if defined(CONFIG_40x) || defined(CONFIG_BOOKE) - task->thread.dbcr0 = DBCR0_IDM | DBCR0_IC; + task->thread.dbcr0 |= DBCR0_IDM | DBCR0_IC; regs->msr |= MSR_DE; #else regs->msr |= MSR_SE; @@ -716,9 +716,16 @@ void user_disable_single_step(struct task_struct *task) { struct pt_regs *regs = task->thread.regs; + +#if defined(CONFIG_44x) || defined(CONFIG_BOOKE) + /* If DAC then do not single step, skip */ + if (task->thread.dabr) + return; +#endif + if (regs != NULL) { #if defined(CONFIG_40x) || defined(CONFIG_BOOKE) - task->thread.dbcr0 = 0; + task->thread.dbcr0 &= ~(DBCR0_IC | DBCR0_IDM); regs->msr &= ~MSR_DE; #else regs->msr &= ~MSR_SE; @@ -727,22 +734,75 @@ void user_disable_single_step(struct task_struct *task) clear_tsk_thread_flag(task, TIF_SINGLESTEP); } -static int ptrace_set_debugreg(struct task_struct *task, unsigned long addr, +int ptrace_set_debugreg(struct task_struct *task, unsigned long addr, unsigned long data) { - /* We only support one DABR and no IABRS at the moment */ + /* For ppc64 we support one DABR and no IABR's at the moment (ppc64). + * For embedded processors we support one DAC and no IAC's at the + * moment. + */ if (addr > 0) return -EINVAL; - /* The bottom 3 bits are flags */ if ((data & ~0x7UL) >= TASK_SIZE) return -EIO; - /* Ensure translation is on */ +#ifdef CONFIG_PPC64 + + /* For processors using DABR (i.e. 970), the bottom 3 bits are flags. + * It was assumed, on previous implementations, that 3 bits were + * passed together with the data address, fitting the design of the + * DABR register, as follows: + * + * bit 0: Read flag + * bit 1: Write flag + * bit 2: Breakpoint translation + * + * Thus, we use them here as so. + */ + + /* Ensure breakpoint translation bit is set */ if (data && !(data & DABR_TRANSLATION)) return -EIO; + /* Move contents to the DABR register */ task->thread.dabr = data; + +#endif +#if defined(CONFIG_44x) || defined(CONFIG_BOOKE) + + /* As described above, it was assumed 3 bits were passed with the data + * address, but we will assume only the mode bits will be passed + * as to not cause alignment restrictions for DAC-based processors. + */ + + /* DAC's hold the whole address without any mode flags */ + task->thread.dabr = data & ~0x3UL; + + if (task->thread.dabr == 0) { + task->thread.dbcr0 &= ~(DBSR_DAC1R | DBSR_DAC1W | DBCR0_IDM); + task->thread.regs->msr &= ~MSR_DE; + return 0; + } + + /* Read or Write bits must be set */ + + if (!(data & 0x3UL)) + return -EINVAL; + + /* Set the Internal Debugging flag (IDM bit 1) for the DBCR0 + register */ + task->thread.dbcr0 = DBCR0_IDM; + + /* Check for write and read flags and set DBCR0 + accordingly */ + if (data & 0x1UL) + task->thread.dbcr0 |= DBSR_DAC1R; + if (data & 0x2UL) + task->thread.dbcr0 |= DBSR_DAC1W; + + task->thread.regs->msr |= MSR_DE; +#endif return 0; } diff --git a/arch/powerpc/kernel/signal.c b/arch/powerpc/kernel/signal.c index ad55488939c3..7aada783ec6a 100644 --- a/arch/powerpc/kernel/signal.c +++ b/arch/powerpc/kernel/signal.c @@ -145,8 +145,12 @@ int do_signal(sigset_t *oldset, struct pt_regs *regs) * user space. The DABR will have been cleared if it * triggered inside the kernel. */ - if (current->thread.dabr) + if (current->thread.dabr) { set_dabr(current->thread.dabr); +#if defined(CONFIG_44x) || defined(CONFIG_BOOKE) + mtspr(SPRN_DBCR0, current->thread.dbcr0); +#endif + } if (is32) { if (ka.sa.sa_flags & SA_SIGINFO) diff --git a/arch/powerpc/kernel/traps.c b/arch/powerpc/kernel/traps.c index 878fbddb6ae1..81ccb8dd1a54 100644 --- a/arch/powerpc/kernel/traps.c +++ b/arch/powerpc/kernel/traps.c @@ -1067,6 +1067,22 @@ void __kprobes DebugException(struct pt_regs *regs, unsigned long debug_status) } _exception(SIGTRAP, regs, TRAP_TRACE, regs->nip); + } else if (debug_status & (DBSR_DAC1R | DBSR_DAC1W)) { + regs->msr &= ~MSR_DE; + + if (user_mode(regs)) { + current->thread.dbcr0 &= ~(DBSR_DAC1R | DBSR_DAC1W | + DBCR0_IDM); + } else { + /* Disable DAC interupts */ + mtspr(SPRN_DBCR0, mfspr(SPRN_DBCR0) & ~(DBSR_DAC1R | + DBSR_DAC1W | DBCR0_IDM)); + + /* Clear the DAC event */ + mtspr(SPRN_DBSR, (DBSR_DAC1R | DBSR_DAC1W)); + } + /* Setup and send the trap to the handler */ + do_dabr(regs, mfspr(SPRN_DAC1), debug_status); } } #endif /* CONFIG_4xx || CONFIG_BOOKE */ diff --git a/arch/powerpc/mm/fault.c b/arch/powerpc/mm/fault.c index 1707d00331fc..565b7a237c84 100644 --- a/arch/powerpc/mm/fault.c +++ b/arch/powerpc/mm/fault.c @@ -100,31 +100,6 @@ static int store_updates_sp(struct pt_regs *regs) return 0; } -#if !(defined(CONFIG_4xx) || defined(CONFIG_BOOKE)) -static void do_dabr(struct pt_regs *regs, unsigned long address, - unsigned long error_code) -{ - siginfo_t info; - - if (notify_die(DIE_DABR_MATCH, "dabr_match", regs, error_code, - 11, SIGSEGV) == NOTIFY_STOP) - return; - - if (debugger_dabr_match(regs)) - return; - - /* Clear the DABR */ - set_dabr(0); - - /* Deliver the signal to userspace */ - info.si_signo = SIGTRAP; - info.si_errno = 0; - info.si_code = TRAP_HWBKPT; - info.si_addr = (void __user *)address; - force_sig_info(SIGTRAP, &info, current); -} -#endif /* !(CONFIG_4xx || CONFIG_BOOKE)*/ - /* * For 600- and 800-family processors, the error_code parameter is DSISR * for a data fault, SRR1 for an instruction fault. For 400-family processors diff --git a/include/asm-powerpc/system.h b/include/asm-powerpc/system.h index e6e25e2364eb..d6648c143322 100644 --- a/include/asm-powerpc/system.h +++ b/include/asm-powerpc/system.h @@ -110,6 +110,8 @@ static inline int debugger_fault_handler(struct pt_regs *regs) { return 0; } #endif extern int set_dabr(unsigned long dabr); +extern void do_dabr(struct pt_regs *regs, unsigned long address, + unsigned long error_code); extern void print_backtrace(unsigned long *); extern void show_regs(struct pt_regs * regs); extern void flush_instruction_cache(void); |