diff options
| -rw-r--r-- | Documentation/w1/00-INDEX | 2 | ||||
| -rw-r--r-- | Documentation/w1/slaves/00-INDEX | 4 | ||||
| -rw-r--r-- | Documentation/w1/slaves/w1_therm | 41 | ||||
| -rw-r--r-- | drivers/w1/slaves/w1_therm.c | 15 |
4 files changed, 60 insertions, 2 deletions
diff --git a/Documentation/w1/00-INDEX b/Documentation/w1/00-INDEX index 5270cf4cb109..cb49802745dc 100644 --- a/Documentation/w1/00-INDEX +++ b/Documentation/w1/00-INDEX @@ -1,5 +1,7 @@ 00-INDEX - This file +slaves/ + - Drivers that provide support for specific family codes. masters/ - Individual chips providing 1-wire busses. w1.generic diff --git a/Documentation/w1/slaves/00-INDEX b/Documentation/w1/slaves/00-INDEX new file mode 100644 index 000000000000..f8101d6b07b7 --- /dev/null +++ b/Documentation/w1/slaves/00-INDEX @@ -0,0 +1,4 @@ +00-INDEX + - This file +w1_therm + - The Maxim/Dallas Semiconductor ds18*20 temperature sensor. diff --git a/Documentation/w1/slaves/w1_therm b/Documentation/w1/slaves/w1_therm new file mode 100644 index 000000000000..0403aaaba878 --- /dev/null +++ b/Documentation/w1/slaves/w1_therm @@ -0,0 +1,41 @@ +Kernel driver w1_therm +==================== + +Supported chips: + * Maxim ds18*20 based temperature sensors. + +Author: Evgeniy Polyakov <johnpol@2ka.mipt.ru> + + +Description +----------- + +w1_therm provides basic temperature conversion for ds18*20 devices. +supported family codes: +W1_THERM_DS18S20 0x10 +W1_THERM_DS1822 0x22 +W1_THERM_DS18B20 0x28 + +Support is provided through the sysfs w1_slave file. Each open and +read sequence will initiate a temperature conversion then provide two +lines of ASCII output. The first line contains the nine hex bytes +read along with a calculated crc value and YES or NO if it matched. +If the crc matched the returned values are retained. The second line +displays the retained values along with a temperature in millidegrees +Centigrade after t=. + +Parasite powered devices are limited to one slave performing a +temperature conversion at a time. If none of the devices are parasite +powered it would be possible to convert all the devices at the same +time and then go back to read individual sensors. That isn't +currently supported. The driver also doesn't support reduced +precision (which would also reduce the conversion time). + +The module parameter strong_pullup can be set to 0 to disable the +strong pullup or 1 to enable. If enabled the 5V strong pullup will be +enabled when the conversion is taking place provided the master driver +must support the strong pullup (or it falls back to a pullup +resistor). The DS18b20 temperature sensor specification lists a +maximum current draw of 1.5mA and that a 5k pullup resistor is not +sufficient. The strong pullup is designed to provide the additional +current required. diff --git a/drivers/w1/slaves/w1_therm.c b/drivers/w1/slaves/w1_therm.c index fb28acaeed6c..e87f464a6fb0 100644 --- a/drivers/w1/slaves/w1_therm.c +++ b/drivers/w1/slaves/w1_therm.c @@ -37,6 +37,14 @@ MODULE_LICENSE("GPL"); MODULE_AUTHOR("Evgeniy Polyakov <johnpol@2ka.mipt.ru>"); MODULE_DESCRIPTION("Driver for 1-wire Dallas network protocol, temperature family."); +/* Allow the strong pullup to be disabled, but default to enabled. + * If it was disabled a parasite powered device might not get the require + * current to do a temperature conversion. If it is enabled parasite powered + * devices have a better chance of getting the current required. + */ +static int w1_strong_pullup = 1; +module_param_named(strong_pullup, w1_strong_pullup, int, 0); + static u8 bad_roms[][9] = { {0xaa, 0x00, 0x4b, 0x46, 0xff, 0xff, 0x0c, 0x10, 0x87}, {} @@ -192,9 +200,12 @@ static ssize_t w1_therm_read_bin(struct kobject *kobj, int count = 0; unsigned int tm = 750; + /* 750ms strong pullup (or delay) after the convert */ + if (w1_strong_pullup) + w1_next_pullup(dev, tm); w1_write_8(dev, W1_CONVERT_TEMP); - - msleep(tm); + if (!w1_strong_pullup) + msleep(tm); if (!w1_reset_select_slave(sl)) { |