diff options
| -rw-r--r-- | drivers/mtd/nand/au1550nd.c | 139 |
1 files changed, 139 insertions, 0 deletions
diff --git a/drivers/mtd/nand/au1550nd.c b/drivers/mtd/nand/au1550nd.c index 839b35a386b6..d9a0143e1d3a 100644 --- a/drivers/mtd/nand/au1550nd.c +++ b/drivers/mtd/nand/au1550nd.c @@ -14,6 +14,7 @@ #include <linux/slab.h> #include <linux/init.h> #include <linux/module.h> +#include <linux/interrupt.h> #include <linux/mtd/mtd.h> #include <linux/mtd/nand.h> #include <linux/mtd/partitions.h> @@ -318,6 +319,141 @@ int au1550_device_ready(struct mtd_info *mtd) return ret; } +/** + * au1550_select_chip - control -CE line + * Forbid driving -CE manually permitting the NAND controller to do this. + * Keeping -CE asserted during the whole sector reads interferes with the + * NOR flash and PCMCIA drivers as it causes contention on the static bus. + * We only have to hold -CE low for the NAND read commands since the flash + * chip needs it to be asserted during chip not ready time but the NAND + * controller keeps it released. + * + * @mtd: MTD device structure + * @chip: chipnumber to select, -1 for deselect + */ +static void au1550_select_chip(struct mtd_info *mtd, int chip) +{ +} + +/** + * au1550_command - Send command to NAND device + * @mtd: MTD device structure + * @command: the command to be sent + * @column: the column address for this command, -1 if none + * @page_addr: the page address for this command, -1 if none + */ +static void au1550_command(struct mtd_info *mtd, unsigned command, int column, int page_addr) +{ + register struct nand_chip *this = mtd->priv; + int ce_override = 0, i; + ulong flags; + + /* Begin command latch cycle */ + this->hwcontrol(mtd, NAND_CTL_SETCLE); + /* + * Write out the command to the device. + */ + if (command == NAND_CMD_SEQIN) { + int readcmd; + + if (column >= mtd->oobblock) { + /* OOB area */ + column -= mtd->oobblock; + readcmd = NAND_CMD_READOOB; + } else if (column < 256) { + /* First 256 bytes --> READ0 */ + readcmd = NAND_CMD_READ0; + } else { + column -= 256; + readcmd = NAND_CMD_READ1; + } + this->write_byte(mtd, readcmd); + } + this->write_byte(mtd, command); + + /* Set ALE and clear CLE to start address cycle */ + this->hwcontrol(mtd, NAND_CTL_CLRCLE); + + if (column != -1 || page_addr != -1) { + this->hwcontrol(mtd, NAND_CTL_SETALE); + + /* Serially input address */ + if (column != -1) { + /* Adjust columns for 16 bit buswidth */ + if (this->options & NAND_BUSWIDTH_16) + column >>= 1; + this->write_byte(mtd, column); + } + if (page_addr != -1) { + this->write_byte(mtd, (u8)(page_addr & 0xff)); + + if (command == NAND_CMD_READ0 || + command == NAND_CMD_READ1 || + command == NAND_CMD_READOOB) { + /* + * NAND controller will release -CE after + * the last address byte is written, so we'll + * have to forcibly assert it. No interrupts + * are allowed while we do this as we don't + * want the NOR flash or PCMCIA drivers to + * steal our precious bytes of data... + */ + ce_override = 1; + local_irq_save(flags); + this->hwcontrol(mtd, NAND_CTL_SETNCE); + } + + this->write_byte(mtd, (u8)(page_addr >> 8)); + + /* One more address cycle for devices > 32MiB */ + if (this->chipsize > (32 << 20)) + this->write_byte(mtd, (u8)((page_addr >> 16) & 0x0f)); + } + /* Latch in address */ + this->hwcontrol(mtd, NAND_CTL_CLRALE); + } + + /* + * Program and erase have their own busy handlers. + * Status and sequential in need no delay. + */ + switch (command) { + + case NAND_CMD_PAGEPROG: + case NAND_CMD_ERASE1: + case NAND_CMD_ERASE2: + case NAND_CMD_SEQIN: + case NAND_CMD_STATUS: + return; + + case NAND_CMD_RESET: + break; + + case NAND_CMD_READ0: + case NAND_CMD_READ1: + case NAND_CMD_READOOB: + /* Check if we're really driving -CE low (just in case) */ + if (unlikely(!ce_override)) + break; + + /* Apply a short delay always to ensure that we do wait tWB. */ + ndelay(100); + /* Wait for a chip to become ready... */ + for (i = this->chip_delay; !this->dev_ready(mtd) && i > 0; --i) + udelay(1); + + /* Release -CE and re-enable interrupts. */ + this->hwcontrol(mtd, NAND_CTL_CLRNCE); + local_irq_restore(flags); + return; + } + /* Apply this short delay always to ensure that we do wait tWB. */ + ndelay(100); + + while(!this->dev_ready(mtd)); +} + + /* * Main initialization routine */ @@ -437,6 +573,9 @@ static int __init au1xxx_nand_init(void) /* Set address of hardware control function */ this->hwcontrol = au1550_hwcontrol; this->dev_ready = au1550_device_ready; + this->select_chip = au1550_select_chip; + this->cmdfunc = au1550_command; + /* 30 us command delay time */ this->chip_delay = 30; this->eccmode = NAND_ECC_SOFT; |