diff options
| -rw-r--r-- | Documentation/i2c/busses/i2c-piix4 | 22 | ||||
| -rw-r--r-- | drivers/i2c/busses/i2c-piix4.c | 25 |
2 files changed, 17 insertions, 30 deletions
diff --git a/Documentation/i2c/busses/i2c-piix4 b/Documentation/i2c/busses/i2c-piix4 index 6e6c905143a1..10957bee7f64 100644 --- a/Documentation/i2c/busses/i2c-piix4 +++ b/Documentation/i2c/busses/i2c-piix4 @@ -23,8 +23,6 @@ Module Parameters Forcibly enable the PIIX4. DANGEROUS! * force_addr: int Forcibly enable the PIIX4 at the given address. EXTREMELY DANGEROUS! -* fix_hstcfg: int - Fix config register. Needed on some boards (Force CPCI735). Description @@ -68,7 +66,19 @@ this driver on those mainboards. The ServerWorks Southbridges, the Intel 440MX, and the Victory766 are identical to the PIIX4 in I2C/SMBus support. -A few OSB4 southbridges are known to be misconfigured by the BIOS. In this -case, you have you use the fix_hstcfg module parameter. Do not use it -unless you know you have to, because in some cases it also breaks -configuration on southbridges that don't need it. +If you own Force CPCI735 motherboard or other OSB4 based systems you may need +to change the SMBus Interrupt Select register so the SMBus controller uses +the SMI mode. + +1) Use lspci command and locate the PCI device with the SMBus controller: + 00:0f.0 ISA bridge: ServerWorks OSB4 South Bridge (rev 4f) + The line may vary for different chipsets. Please consult the driver source + for all possible PCI ids (and lspci -n to match them). Lets assume the + device is located at 00:0f.0. +2) Now you just need to change the value in 0xD2 register. Get it first with + command: lspci -xxx -s 00:0f.0 + If the value is 0x3 then you need to change it to 0x1 + setpci -s 00:0f.0 d2.b=1 + +Please note that you don't need to do that in all cases, just when the SMBus is +not working properly. diff --git a/drivers/i2c/busses/i2c-piix4.c b/drivers/i2c/busses/i2c-piix4.c index 5f06e81a2087..05af7b0292f4 100644 --- a/drivers/i2c/busses/i2c-piix4.c +++ b/drivers/i2c/busses/i2c-piix4.c @@ -102,13 +102,6 @@ MODULE_PARM_DESC(force_addr, "Forcibly enable the PIIX4 at the given address. " "EXTREMELY DANGEROUS!"); -/* If fix_hstcfg is set to anything different from 0, we reset one of the - registers to be a valid value. */ -static int fix_hstcfg; -module_param (fix_hstcfg, int, 0); -MODULE_PARM_DESC(fix_hstcfg, - "Fix config register. Needed on some boards (Force CPCI735)."); - static int piix4_transaction(void); static unsigned short piix4_smba; @@ -166,22 +159,6 @@ static int __devinit piix4_setup(struct pci_dev *PIIX4_dev, pci_read_config_byte(PIIX4_dev, SMBHSTCFG, &temp); - /* Some BIOS will set up the chipset incorrectly and leave a register - in an undefined state (causing I2C to act very strangely). */ - if (temp & 0x02) { - if (fix_hstcfg) { - dev_info(&PIIX4_dev->dev, "Working around buggy BIOS " - "(I2C)\n"); - temp &= 0xfd; - pci_write_config_byte(PIIX4_dev, SMBHSTCFG, temp); - } else { - dev_info(&PIIX4_dev->dev, "Unusual config register " - "value\n"); - dev_info(&PIIX4_dev->dev, "Try using fix_hstcfg=1 if " - "you experience problems\n"); - } - } - /* If force_addr is set, we program the new address here. Just to make sure, we disable the PIIX4 first. */ if (force_addr) { @@ -214,7 +191,7 @@ static int __devinit piix4_setup(struct pci_dev *PIIX4_dev, } } - if ((temp & 0x0E) == 8) + if (((temp & 0x0E) == 8) || ((temp & 0x0E) == 2)) dev_dbg(&PIIX4_dev->dev, "Using Interrupt 9 for SMBus.\n"); else if ((temp & 0x0E) == 0) dev_dbg(&PIIX4_dev->dev, "Using Interrupt SMI# for SMBus.\n"); |