diff options
Diffstat (limited to 'Documentation/ABI/testing/sysfs-bus-iio')
| -rw-r--r-- | Documentation/ABI/testing/sysfs-bus-iio | 200 |
1 files changed, 199 insertions, 1 deletions
diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio index 117521dbf2b3..9a70c31619ea 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio +++ b/Documentation/ABI/testing/sysfs-bus-iio @@ -92,6 +92,18 @@ Description: is required is a consistent labeling. Units after application of scale and offset are millivolts. +What: /sys/bus/iio/devices/iio:deviceX/in_currentY_raw +What: /sys/bus/iio/devices/iio:deviceX/in_currentY_supply_raw +KernelVersion: 3.17 +Contact: linux-iio@vger.kernel.org +Description: + Raw (unscaled no bias removal etc.) current measurement from + channel Y. In special cases where the channel does not + correspond to externally available input one of the named + versions may be used. The number must always be specified and + unique to allow association with event codes. Units after + application of scale and offset are milliamps. + What: /sys/bus/iio/devices/iio:deviceX/in_capacitanceY_raw KernelVersion: 3.2 Contact: linux-iio@vger.kernel.org @@ -234,6 +246,8 @@ What: /sys/bus/iio/devices/iio:deviceX/in_accel_y_offset What: /sys/bus/iio/devices/iio:deviceX/in_accel_z_offset What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_offset What: /sys/bus/iio/devices/iio:deviceX/in_voltage_offset +What: /sys/bus/iio/devices/iio:deviceX/in_currentY_offset +What: /sys/bus/iio/devices/iio:deviceX/in_current_offset What: /sys/bus/iio/devices/iio:deviceX/in_tempY_offset What: /sys/bus/iio/devices/iio:deviceX/in_temp_offset What: /sys/bus/iio/devices/iio:deviceX/in_pressureY_offset @@ -262,9 +276,14 @@ What: /sys/bus/iio/devices/iio:deviceX/in_voltage_scale What: /sys/bus/iio/devices/iio:deviceX/in_voltage-voltage_scale What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_scale What: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY_scale +What: /sys/bus/iio/devices/iio:deviceX/in_currentY_scale +What: /sys/bus/iio/devices/iio:deviceX/in_currentY_supply_scale +What: /sys/bus/iio/devices/iio:deviceX/in_current_scale What: /sys/bus/iio/devices/iio:deviceX/in_accel_scale What: /sys/bus/iio/devices/iio:deviceX/in_accel_peak_scale What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_scale +What: /sys/bus/iio/devices/iio:deviceX/in_energy_scale +What: /sys/bus/iio/devices/iio:deviceX/in_distance_scale What: /sys/bus/iio/devices/iio:deviceX/in_magn_scale What: /sys/bus/iio/devices/iio:deviceX/in_magn_x_scale What: /sys/bus/iio/devices/iio:deviceX/in_magn_y_scale @@ -276,6 +295,7 @@ What: /sys/bus/iio/devices/iio:deviceX/in_rot_from_north_true_tilt_comp_scale What: /sys/bus/iio/devices/iio:deviceX/in_pressureY_scale What: /sys/bus/iio/devices/iio:deviceX/in_pressure_scale What: /sys/bus/iio/devices/iio:deviceX/in_humidityrelative_scale +What: /sys/bus/iio/devices/iio:deviceX/in_velocity_sqrt(x^2+y^2+z^2)_scale KernelVersion: 2.6.35 Contact: linux-iio@vger.kernel.org Description: @@ -323,6 +343,44 @@ Description: production inaccuracies). If shared across all channels, <type>_calibscale is used. +What: /sys/bus/iio/devices/iio:deviceX/in_activity_calibgender +What: /sys/bus/iio/devices/iio:deviceX/in_energy_calibgender +What: /sys/bus/iio/devices/iio:deviceX/in_distance_calibgender +What: /sys/bus/iio/devices/iio:deviceX/in_velocity_calibgender +KernelVersion: 3.20 +Contact: linux-iio@vger.kernel.org +Description: + Gender of the user (e.g.: male, female) used by some pedometers + to compute the stride length, distance, speed and activity + type. + +What: /sys/bus/iio/devices/iio:deviceX/in_activity_calibgender_available +What: /sys/bus/iio/devices/iio:deviceX/in_energy_calibgender_available +What: /sys/bus/iio/devices/iio:deviceX/in_distance_calibgender_available +What: /sys/bus/iio/devices/iio:deviceX/in_velocity_calibgender_available +KernelVersion: 3.20 +Contact: linux-iio@vger.kernel.org +Description: + Lists all available gender values (e.g.: male, female). + +What: /sys/bus/iio/devices/iio:deviceX/in_activity_calibheight +What: /sys/bus/iio/devices/iio:deviceX/in_energy_calibheight +What: /sys/bus/iio/devices/iio:deviceX/in_distance_calibheight +What: /sys/bus/iio/devices/iio:deviceX/in_velocity_calibheight +KernelVersion: 3.19 +Contact: linux-iio@vger.kernel.org +Description: + Height of the user (in meters) used by some pedometers + to compute the stride length, distance, speed and activity + type. + +What: /sys/bus/iio/devices/iio:deviceX/in_energy_calibweight +KernelVersion: 3.20 +Contact: linux-iio@vger.kernel.org +Description: + Weight of the user (in kg). It is needed by some pedometers + to compute the calories burnt by the user. + What: /sys/bus/iio/devices/iio:deviceX/in_accel_scale_available What: /sys/.../iio:deviceX/in_voltageX_scale_available What: /sys/.../iio:deviceX/in_voltage-voltage_scale_available @@ -783,6 +841,14 @@ What: /sys/.../events/in_tempY_roc_falling_period What: /sys/.../events/in_accel_x&y&z_mag_falling_period What: /sys/.../events/in_intensity0_thresh_period What: /sys/.../events/in_proximity0_thresh_period +What: /sys/.../events/in_activity_still_thresh_rising_period +What: /sys/.../events/in_activity_still_thresh_falling_period +What: /sys/.../events/in_activity_walking_thresh_rising_period +What: /sys/.../events/in_activity_walking_thresh_falling_period +What: /sys/.../events/in_activity_jogging_thresh_rising_period +What: /sys/.../events/in_activity_jogging_thresh_falling_period +What: /sys/.../events/in_activity_running_thresh_rising_period +What: /sys/.../events/in_activity_running_thresh_falling_period KernelVersion: 2.6.37 Contact: linux-iio@vger.kernel.org Description: @@ -790,6 +856,40 @@ Description: met before an event is generated. If direction is not specified then this period applies to both directions. +What: /sys/.../events/in_activity_still_thresh_rising_en +What: /sys/.../events/in_activity_still_thresh_falling_en +What: /sys/.../events/in_activity_walking_thresh_rising_en +What: /sys/.../events/in_activity_walking_thresh_falling_en +What: /sys/.../events/in_activity_jogging_thresh_rising_en +What: /sys/.../events/in_activity_jogging_thresh_falling_en +What: /sys/.../events/in_activity_running_thresh_rising_en +What: /sys/.../events/in_activity_running_thresh_falling_en +KernelVersion: 3.19 +Contact: linux-iio@vger.kernel.org +Description: + Enables or disables activitity events. Depending on direction + an event is generated when sensor ENTERS or LEAVES a given state. + +What: /sys/.../events/in_activity_still_thresh_rising_value +What: /sys/.../events/in_activity_still_thresh_falling_value +What: /sys/.../events/in_activity_walking_thresh_rising_value +What: /sys/.../events/in_activity_walking_thresh_falling_value +What: /sys/.../events/in_activity_jogging_thresh_rising_value +What: /sys/.../events/in_activity_jogging_thresh_falling_value +What: /sys/.../events/in_activity_running_thresh_rising_value +What: /sys/.../events/in_activity_running_thresh_falling_value +KernelVersion: 3.19 +Contact: linux-iio@vger.kernel.org +Description: + Confidence value (in units as percentage) to be used + for deciding when an event should be generated. E.g for + running: If the confidence value reported by the sensor + is greater than in_activity_running_thresh_rising_value + then the sensor ENTERS running state. Conversely, if the + confidence value reported by the sensor is lower than + in_activity_running_thresh_falling_value then the sensor + is LEAVING running state. + What: /sys/.../iio:deviceX/events/in_accel_mag_en What: /sys/.../iio:deviceX/events/in_accel_mag_rising_en What: /sys/.../iio:deviceX/events/in_accel_mag_falling_en @@ -822,6 +922,25 @@ Description: number or direction is not specified, applies to all channels of this type. +What: /sys/.../events/in_steps_change_en +KernelVersion: 3.20 +Contact: linux-iio@vger.kernel.org +Description: + Event generated when channel passes a threshold on the absolute + change in value. E.g. for steps: a step change event is + generated each time the user takes N steps, where N is set using + in_steps_change_value. + +What: /sys/.../events/in_steps_change_value +KernelVersion: 3.20 +Contact: linux-iio@vger.kernel.org +Description: + Specifies the value of change threshold that the + device is comparing against for the events enabled by + <type>[Y][_name]_roc[_rising|falling|]_en. E.g. for steps: + if set to 3, a step change event will be generated every 3 + steps. + What: /sys/bus/iio/devices/iio:deviceX/trigger/current_trigger KernelVersion: 2.6.35 Contact: linux-iio@vger.kernel.org @@ -956,6 +1075,16 @@ Description: and the relevant _type attributes to establish the data storage format. +What: /sys/.../iio:deviceX/in_activity_still_input +What: /sys/.../iio:deviceX/in_activity_walking_input +What: /sys/.../iio:deviceX/in_activity_jogging_input +What: /sys/.../iio:deviceX/in_activity_running_input +KernelVersion: 3.19 +Contact: linux-iio@vger.kernel.org +Description: + This attribute is used to read the confidence for an activity + expressed in units as percentage. + What: /sys/.../iio:deviceX/in_anglvel_z_quadrature_correction_raw KernelVersion: 2.6.38 Contact: linux-iio@vger.kernel.org @@ -973,6 +1102,24 @@ Description: For a list of available output power modes read in_accel_power_mode_available. +What: /sys/.../iio:deviceX/in_energy_input +What: /sys/.../iio:deviceX/in_energy_raw +KernelVersion: 3.20 +Contact: linux-iio@vger.kernel.org +Description: + This attribute is used to read the energy value reported by the + device (e.g.: human activity sensors report energy burnt by the + user). Units after application of scale are Joules. + +What: /sys/.../iio:deviceX/in_distance_input +What: /sys/.../iio:deviceX/in_distance_raw +KernelVersion: 3.20 +Contact: linux-iio@vger.kernel.org +Description: + This attribute is used to read the distance covered by the user + since the last reboot while activated. Units after application + of scale are meters. + What: /sys/bus/iio/devices/iio:deviceX/store_eeprom KernelVersion: 3.4.0 Contact: linux-iio@vger.kernel.org @@ -992,7 +1139,9 @@ Description: reflectivity of infrared or ultrasound emitted. Often these sensors are unit less and as such conversion to SI units is not possible. Where it is, the units should - be meters. + be meters. If such a conversion is not possible, the reported + values should behave in the same way as a distance, i.e. lower + values indicate something is closer to the sensor. What: /sys/.../iio:deviceX/in_illuminanceY_input What: /sys/.../iio:deviceX/in_illuminanceY_raw @@ -1024,6 +1173,12 @@ Description: This attribute is used to get/set the integration time in seconds. +What: /sys/.../iio:deviceX/in_velocity_sqrt(x^2+y^2+z^2)_integration_time +KernelVersion: 3.20 +Contact: linux-iio@vger.kernel.org +Description: + Number of seconds in which to compute speed. + What: /sys/bus/iio/devices/iio:deviceX/in_rot_quaternion_raw KernelVersion: 3.15 Contact: linux-iio@vger.kernel.org @@ -1051,3 +1206,46 @@ Description: after application of scale and offset. If no offset or scale is present, output should be considered as processed with the unit in milliamps. + +What: /sys/.../iio:deviceX/in_energy_en +What: /sys/.../iio:deviceX/in_distance_en +What: /sys/.../iio:deviceX/in_velocity_sqrt(x^2+y^2+z^2)_en +What: /sys/.../iio:deviceX/in_steps_en +KernelVersion: 3.19 +Contact: linux-iio@vger.kernel.org +Description: + Activates a device feature that runs in firmware/hardware. + E.g. for steps: the pedometer saves power while not used; + when activated, it will count the steps taken by the user in + firmware and export them through in_steps_input. + +What: /sys/.../iio:deviceX/in_steps_input +KernelVersion: 3.19 +Contact: linux-iio@vger.kernel.org +Description: + This attribute is used to read the number of steps taken by the user + since the last reboot while activated. + +What: /sys/.../iio:deviceX/in_velocity_sqrt(x^2+y^2+z^2)_input +What: /sys/.../iio:deviceX/in_velocity_sqrt(x^2+y^2+z^2)_raw +KernelVersion: 3.19 +Contact: linux-iio@vger.kernel.org +Description: + This attribute is used to read the current speed value of the + user (which is the norm or magnitude of the velocity vector). + Units after application of scale are m/s. + +What: /sys/.../iio:deviceX/in_steps_debounce_count +KernelVersion: 3.20 +Contact: linux-iio@vger.kernel.org +Description: + Specifies the number of steps that must occur within + in_steps_filter_debounce_time for the pedometer to decide the + consumer is making steps. + +What: /sys/.../iio:deviceX/in_steps_debounce_time +KernelVersion: 3.20 +Contact: linux-iio@vger.kernel.org +Description: + Specifies number of seconds in which we compute the steps + that occur in order to decide if the consumer is making steps. |