diff options
Diffstat (limited to 'Documentation/devicetree/bindings/gpio')
| -rw-r--r-- | Documentation/devicetree/bindings/gpio/gpio-nmk.txt | 31 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/gpio/mrvl-gpio.txt | 18 |
2 files changed, 43 insertions, 6 deletions
diff --git a/Documentation/devicetree/bindings/gpio/gpio-nmk.txt b/Documentation/devicetree/bindings/gpio/gpio-nmk.txt new file mode 100644 index 000000000000..ee87467ad8d6 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-nmk.txt @@ -0,0 +1,31 @@ +Nomadik GPIO controller + +Required properties: +- compatible : Should be "st,nomadik-gpio". +- reg : Physical base address and length of the controller's registers. +- interrupts : The interrupt outputs from the controller. +- #gpio-cells : Should be two: + The first cell is the pin number. + The second cell is used to specify optional parameters: + - bits[3:0] trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. +- gpio-controller : Marks the device node as a GPIO controller. +- interrupt-controller : Marks the device node as an interrupt controller. +- gpio-bank : Specifies which bank a controller owns. +- st,supports-sleepmode : Specifies whether controller can sleep or not + +Example: + + gpio1: gpio@8012e080 { + compatible = "st,nomadik-gpio"; + reg = <0x8012e080 0x80>; + interrupts = <0 120 0x4>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + supports-sleepmode; + gpio-bank = <1>; + }; diff --git a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt index 1e34cfe5ebea..05428f39d9ac 100644 --- a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt @@ -3,19 +3,25 @@ Required properties: - compatible : Should be "mrvl,pxa-gpio" or "mrvl,mmp-gpio" - reg : Address and length of the register set for the device -- interrupts : Should be the port interrupt shared by all gpio pins, if -- interrupt-name : Should be the name of irq resource. - one number. +- interrupts : Should be the port interrupt shared by all gpio pins. + There're three gpio interrupts in arch-pxa, and they're gpio0, + gpio1 and gpio_mux. There're only one gpio interrupt in arch-mmp, + gpio_mux. +- interrupt-name : Should be the name of irq resource. Each interrupt + binds its interrupt-name. +- interrupt-controller : Identifies the node as an interrupt controller. +- #interrupt-cells: Specifies the number of cells needed to encode an + interrupt source. - gpio-controller : Marks the device node as a gpio controller. - #gpio-cells : Should be one. It is the pin number. Example: gpio: gpio@d4019000 { - compatible = "mrvl,mmp-gpio", "mrvl,pxa-gpio"; + compatible = "mrvl,mmp-gpio"; reg = <0xd4019000 0x1000>; - interrupts = <49>, <17>, <18>; - interrupt-name = "gpio_mux", "gpio0", "gpio1"; + interrupts = <49>; + interrupt-name = "gpio_mux"; gpio-controller; #gpio-cells = <1>; interrupt-controller; |