diff options
Diffstat (limited to 'Documentation/devicetree/bindings/i2c')
6 files changed, 64 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/i2c/i2c-davinci.txt b/Documentation/devicetree/bindings/i2c/i2c-davinci.txt index a4e1cbc810c1..5b123e0e4cc2 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-davinci.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-davinci.txt @@ -1,10 +1,10 @@ -* Texas Instruments Davinci I2C +* Texas Instruments Davinci/Keystone I2C This file provides information, what the device node for the -davinci i2c interface contain. +davinci/keystone i2c interface contains. Required properties: -- compatible: "ti,davinci-i2c"; +- compatible: "ti,davinci-i2c" or "ti,keystone-i2c"; - reg : Offset and length of the register set for the device Recommended properties : diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx.txt b/Documentation/devicetree/bindings/i2c/i2c-imx.txt index ce4311d726ae..eab5836ba7f9 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-imx.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-imx.txt @@ -14,6 +14,10 @@ Optional properties: The absence of the propoerty indicates the default frequency 100 kHz. - dmas: A list of two dma specifiers, one for each entry in dma-names. - dma-names: should contain "tx" and "rx". +- scl-gpios: specify the gpio related to SCL pin +- sda-gpios: specify the gpio related to SDA pin +- pinctrl: add extra pinctrl to configure i2c pins to gpio function for i2c + bus recovery, call it "gpio" state Examples: @@ -37,4 +41,9 @@ i2c0: i2c@40066000 { /* i2c0 on vf610 */ dmas = <&edma0 0 50>, <&edma0 0 51>; dma-names = "rx","tx"; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c1>; + pinctrl-1 = <&pinctrl_i2c1_gpio>; + scl-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH>; + sda-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt index 16b3e07aa98f..ea406eb20fa5 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt @@ -10,6 +10,7 @@ Required properties: "renesas,i2c-r8a7792" "renesas,i2c-r8a7793" "renesas,i2c-r8a7794" + "renesas,i2c-r8a7795" - reg: physical base address of the controller and length of memory mapped region. - interrupts: interrupt specifier. diff --git a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt index 2bfc6e7ed094..214f94c25d37 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt @@ -10,6 +10,7 @@ Required properties: - "renesas,iic-r8a7792" (R-Car V2H) - "renesas,iic-r8a7793" (R-Car M2-N) - "renesas,iic-r8a7794" (R-Car E2) + - "renesas,iic-r8a7795" (R-Car H3) - "renesas,iic-sh73a0" (SH-Mobile AG5) - reg : address start and address range size of device - interrupts : interrupt of device diff --git a/Documentation/devicetree/bindings/i2c/i2c-uniphier-f.txt b/Documentation/devicetree/bindings/i2c/i2c-uniphier-f.txt new file mode 100644 index 000000000000..27fc6f8c798b --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-uniphier-f.txt @@ -0,0 +1,25 @@ +UniPhier I2C controller (FIFO-builtin) + +Required properties: +- compatible: should be "socionext,uniphier-fi2c". +- #address-cells: should be 1. +- #size-cells: should be 0. +- reg: offset and length of the register set for the device. +- interrupts: a single interrupt specifier. +- clocks: phandle to the input clock. + +Optional properties: +- clock-frequency: desired I2C bus frequency in Hz. The maximum supported + value is 400000. Defaults to 100000 if not specified. + +Examples: + + i2c0: i2c@58780000 { + compatible = "socionext,uniphier-fi2c"; + reg = <0x58780000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 41 4>; + clocks = <&i2c_clk>; + clock-frequency = <100000>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-uniphier.txt b/Documentation/devicetree/bindings/i2c/i2c-uniphier.txt new file mode 100644 index 000000000000..26f9d95b3436 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-uniphier.txt @@ -0,0 +1,25 @@ +UniPhier I2C controller (FIFO-less) + +Required properties: +- compatible: should be "socionext,uniphier-i2c". +- #address-cells: should be 1. +- #size-cells: should be 0. +- reg: offset and length of the register set for the device. +- interrupts: a single interrupt specifier. +- clocks: phandle to the input clock. + +Optional properties: +- clock-frequency: desired I2C bus frequency in Hz. The maximum supported + value is 400000. Defaults to 100000 if not specified. + +Examples: + + i2c0: i2c@58400000 { + compatible = "socionext,uniphier-i2c"; + reg = <0x58400000 0x40>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 41 1>; + clocks = <&i2c_clk>; + clock-frequency = <100000>; + }; |