diff options
Diffstat (limited to 'Documentation/devicetree/bindings/input')
7 files changed, 178 insertions, 2 deletions
diff --git a/Documentation/devicetree/bindings/input/gpio-keys.txt b/Documentation/devicetree/bindings/input/gpio-keys.txt index cf1333d1dd52..21641236c095 100644 --- a/Documentation/devicetree/bindings/input/gpio-keys.txt +++ b/Documentation/devicetree/bindings/input/gpio-keys.txt @@ -6,6 +6,7 @@ Required properties: Optional properties: - autorepeat: Boolean, Enable auto repeat feature of Linux input subsystem. + - label: String, name of the input device. Each button (key) is represented as a sub-node of "gpio-keys": Subnode properties: diff --git a/Documentation/devicetree/bindings/input/rotary-encoder.txt b/Documentation/devicetree/bindings/input/rotary-encoder.txt index de99cbbbf6da..6c9f0c8a846c 100644 --- a/Documentation/devicetree/bindings/input/rotary-encoder.txt +++ b/Documentation/devicetree/bindings/input/rotary-encoder.txt @@ -1,7 +1,7 @@ Rotary encoder DT bindings Required properties: -- gpios: a spec for two GPIOs to be used +- gpios: a spec for at least two GPIOs to be used, most significant first Optional properties: - linux,axis: the input subsystem axis to map to this rotary encoder. diff --git a/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt b/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt new file mode 100644 index 000000000000..e3f22d23fc8f --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt @@ -0,0 +1,53 @@ +* Analog Devices AD7879(-1)/AD7889(-1) touchscreen interface (SPI/I2C) + +Required properties: +- compatible : for SPI slave, use "adi,ad7879" + for I2C slave, use "adi,ad7879-1" +- reg : SPI chipselect/I2C slave address + See spi-bus.txt for more SPI slave properties +- interrupt-parent : the phandle for the interrupt controller +- interrupts : touch controller interrupt +- touchscreen-max-pressure : maximum reported pressure +- adi,resistance-plate-x : total resistance of X-plate (for pressure + calculation) +Optional properties: +- touchscreen-swapped-x-y : X and Y axis are swapped (boolean) +- adi,first-conversion-delay : 0-12: In 128us steps (starting with 128us) + 13 : 2.560ms + 14 : 3.584ms + 15 : 4.096ms + This property has to be a '/bits/ 8' value +- adi,acquisition-time : 0: 2us + 1: 4us + 2: 8us + 3: 16us + This property has to be a '/bits/ 8' value +- adi,median-filter-size : 0: disabled + 1: 4 measurements + 2: 8 measurements + 3: 16 measurements + This property has to be a '/bits/ 8' value +- adi,averaging : 0: 2 middle values (1 if median disabled) + 1: 4 middle values + 2: 8 middle values + 3: 16 values + This property has to be a '/bits/ 8' value +- adi,conversion-interval: : 0 : convert one time only + 1-255: 515us + val * 35us (up to 9.440ms) + This property has to be a '/bits/ 8' value + +Example: + + ad7879@2c { + compatible = "adi,ad7879-1"; + reg = <0x2c>; + interrupt-parent = <&gpio1>; + interrupts = <13 IRQ_TYPE_EDGE_FALLING>; + touchscreen-max-pressure = <4096>; + adi,resistance-plate-x = <120>; + adi,first-conversion-delay = /bits/ 8 <3>; + adi,acquisition-time = /bits/ 8 <1>; + adi,median-filter-size = /bits/ 8 <2>; + adi,averaging = /bits/ 8 <1>; + adi,conversion-interval = /bits/ 8 <255>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/cyttsp.txt b/Documentation/devicetree/bindings/input/touchscreen/cyttsp.txt new file mode 100644 index 000000000000..b75d4cfd2c36 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/cyttsp.txt @@ -0,0 +1,95 @@ +* Cypress cyttsp touchscreen controller + +Required properties: + - compatible : must be "cypress,cyttsp-i2c" or "cypress,cyttsp-spi" + - reg : Device I2C address or SPI chip select number + - spi-max-frequency : Maximum SPI clocking speed of the device (for cyttsp-spi) + - interrupt-parent : the phandle for the gpio controller + (see interrupt binding[0]). + - interrupts : (gpio) interrupt to which the chip is connected + (see interrupt binding[0]). + - bootloader-key : the 8-byte bootloader key that is required to switch + the chip from bootloader mode (default mode) to + application mode. + This property has to be specified as an array of 8 + '/bits/ 8' values. + +Optional properties: + - reset-gpios : the reset gpio the chip is connected to + (see GPIO binding[1] for more details). + - touchscreen-size-x : horizontal resolution of touchscreen (in pixels) + - touchscreen-size-y : vertical resolution of touchscreen (in pixels) + - touchscreen-fuzz-x : horizontal noise value of the absolute input device + (in pixels) + - touchscreen-fuzz-y : vertical noise value of the absolute input device + (in pixels) + - active-distance : the distance in pixels beyond which a touch must move + before movement is detected and reported by the device. + Valid values: 0-15. + - active-interval-ms : the minimum period in ms between consecutive + scanning/processing cycles when the chip is in active mode. + Valid values: 0-255. + - lowpower-interval-ms : the minimum period in ms between consecutive + scanning/processing cycles when the chip is in low-power mode. + Valid values: 0-2550 + - touch-timeout-ms : minimum time in ms spent in the active power state while no + touches are detected before entering low-power mode. + Valid values: 0-2550 + - use-handshake : enable register-based handshake (boolean). This should + only be used if the chip is configured to use 'blocking + communication with timeout' (in this case the device + generates an interrupt at the end of every + scanning/processing cycle). + +[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +[1]: Documentation/devicetree/bindings/gpio/gpio.txt + +Example: + &i2c1 { + /* ... */ + cyttsp@a { + compatible = "cypress,cyttsp-i2c"; + reg = <0xa>; + interrupt-parent = <&gpio0>; + interrupts = <28 0>; + reset-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; + + touchscreen-size-x = <800>; + touchscreen-size-y = <480>; + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + + bootloader-key = /bits/ 8 <0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08>; + active-distance = <8>; + active-interval-ms = <0>; + lowpower-interval-ms = <200>; + touch-timeout-ms = <100>; + }; + + /* ... */ + }; + + &mcspi1 { + /* ... */ + cyttsp@0 { + compatible = "cypress,cyttsp-spi"; + spi-max-frequency = <6000000>; + reg = <0>; + interrupt-parent = <&gpio0>; + interrupts = <28 0>; + reset-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; + + touchscreen-size-x = <800>; + touchscreen-size-y = <480>; + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + + bootloader-key = /bits/ 8 <0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08>; + active-distance = <8>; + active-interval-ms = <0>; + lowpower-interval-ms = <200>; + touch-timeout-ms = <100>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt index 8ba98eec765b..c98757a69110 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt @@ -13,6 +13,17 @@ Required properties: - interrupt-parent : Interrupt controller to which the chip is connected - interrupts : Interrupt to which the chip is connected +Optional properties: + + - irq-gpios : GPIO pin used for IRQ. The driver uses the + interrupt gpio pin as output to reset the device. + - reset-gpios : GPIO pin used for reset + + - touchscreen-inverted-x : X axis is inverted (boolean) + - touchscreen-inverted-y : Y axis is inverted (boolean) + - touchscreen-swapped-x-y : X and Y axis are swapped (boolean) + (swapping is done after inverting the axis) + Example: i2c@00000000 { @@ -23,6 +34,9 @@ Example: reg = <0x5d>; interrupt-parent = <&gpio>; interrupts = <0 0>; + + irq-gpios = <&gpio1 0 0>; + reset-gpios = <&gpio1 1 0>; }; /* ... */ diff --git a/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt b/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt index 8eb240a287c8..697a3e7831e7 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt @@ -9,7 +9,9 @@ Required properties: - touchscreen-size-y: vertical resolution of touchscreen (in pixels) Optional properties: -- reset-gpio: GPIO connected to the RESET line of the chip +- reset-gpios: GPIO connected to the RESET line of the chip +- enable-gpios: GPIO connected to the ENABLE line of the chip +- wake-gpios: GPIO connected to the WAKE line of the chip Example: diff --git a/Documentation/devicetree/bindings/input/touchscreen/ts4800-ts.txt b/Documentation/devicetree/bindings/input/touchscreen/ts4800-ts.txt new file mode 100644 index 000000000000..4c1c092c276b --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ts4800-ts.txt @@ -0,0 +1,11 @@ +* TS-4800 Touchscreen bindings + +Required properties: +- compatible: must be "technologic,ts4800-ts" +- reg: physical base address of the controller and length of memory mapped + region. +- syscon: phandle / integers array that points to the syscon node which + describes the FPGA's syscon registers. + - phandle to FPGA's syscon + - offset to the touchscreen register + - offset to the touchscreen enable bit |