diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mfd')
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/atmel-usart.txt | 20 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/ti-lmu.txt | 88 |
2 files changed, 82 insertions, 26 deletions
diff --git a/Documentation/devicetree/bindings/mfd/atmel-usart.txt b/Documentation/devicetree/bindings/mfd/atmel-usart.txt index 7f0cd72f47d2..699fd3c9ace8 100644 --- a/Documentation/devicetree/bindings/mfd/atmel-usart.txt +++ b/Documentation/devicetree/bindings/mfd/atmel-usart.txt @@ -17,17 +17,24 @@ Required properties for USART in SPI mode: - cs-gpios: chipselects (internal cs not supported) - atmel,usart-mode : Must be <AT91_USART_MODE_SPI> (found in dt-bindings/mfd/at91-usart.h) +Optional properties in serial and SPI mode: +- dma bindings for dma transfer: + - dmas: DMA specifier, consisting of a phandle to DMA controller node, + memory peripheral interface and USART DMA channel ID, FIFO configuration. + The order of DMA channels is fixed. The first DMA channel must be TX + associated channel and the second one must be RX associated channel. + Refer to dma.txt and atmel-dma.txt for details. + - dma-names: "tx" for TX channel. + "rx" for RX channel. + The order of dma-names is also fixed. The first name must be "tx" + and the second one must be "rx" as in the examples below. + Optional properties in serial mode: - atmel,use-dma-rx: use of PDC or DMA for receiving data - atmel,use-dma-tx: use of PDC or DMA for transmitting data - {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD line respectively. It will use specified PIO instead of the peripheral function pin for the USART feature. If unsure, don't specify this property. -- add dma bindings for dma transfer: - - dmas: DMA specifier, consisting of a phandle to DMA controller node, - memory peripheral interface and USART DMA channel ID, FIFO configuration. - Refer to dma.txt and atmel-dma.txt for details. - - dma-names: "rx" for RX channel, "tx" for TX channel. - atmel,fifo-size: maximum number of data the RX and TX FIFOs can store for FIFO capable USARTs. - rs485-rts-delay, rs485-rx-during-tx, linux,rs485-enabled-at-boot-time: see rs485.txt @@ -81,5 +88,8 @@ Example: interrupts = <12 IRQ_TYPE_LEVEL_HIGH 5>; clocks = <&usart0_clk>; clock-names = "usart"; + dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(3)>, + <&dma0 2 (AT91_DMA_CFG_PER_ID(4) | AT91_DMA_CFG_FIFOCFG_ASAP)>; + dma-names = "tx", "rx"; cs-gpios = <&pioB 3 0>; }; diff --git a/Documentation/devicetree/bindings/mfd/ti-lmu.txt b/Documentation/devicetree/bindings/mfd/ti-lmu.txt index 86ca786d54fc..2296b8f24de4 100644 --- a/Documentation/devicetree/bindings/mfd/ti-lmu.txt +++ b/Documentation/devicetree/bindings/mfd/ti-lmu.txt @@ -8,7 +8,7 @@ TI LMU driver supports lighting devices below. LM3632 Backlight and regulator LM3633 Backlight, LED and fault monitor LM3695 Backlight - LM3697 Backlight and fault monitor + LM36274 Backlight and regulator Required properties: - compatible: Should be one of: @@ -16,15 +16,32 @@ Required properties: "ti,lm3632" "ti,lm3633" "ti,lm3695" - "ti,lm3697" + "ti,lm36274" - reg: I2C slave address. 0x11 for LM3632 0x29 for LM3631 - 0x36 for LM3633, LM3697 + 0x36 for LM3633 0x63 for LM3695 + 0x11 for LM36274 -Optional property: +Optional properties: - enable-gpios: A GPIO specifier for hardware enable pin. + - ramp-up-us: Current ramping from one brightness level to + the a higher brightness level. + Range from 2048 us - 117.44 s + - ramp-down-us: Current ramping from one brightness level to + the a lower brightness level. + Range from 2048 us - 117.44 s + - ti,brightness-resolution - This determines whether to use 8 bit brightness + mode or 11 bit brightness mode. If this value is + not set the device is defaulted to the preferred + 8bit brightness mode per 7.3.4.1 of the data + sheet. This setting can either be in the parent + node or as part of the LED child nodes. This + is determined by the part itself if the strings + have a common brightness register or individual + brightness registers. + The values are 255 (8bit) or 2047 (11bit). Required node: - backlight: All LMU devices have backlight child nodes. @@ -35,14 +52,15 @@ Optional nodes: Required properties: - compatible: Should be one of: "ti,lm3633-fault-monitor" - "ti,lm3697-fault-monitor" - leds: LED properties for LM3633. Please refer to [2]. + LED properties for LM36274. Please refer to [4]. - regulators: Regulator properties for LM3631 and LM3632. Please refer to [3]. [1] ../leds/backlight/ti-lmu-backlight.txt [2] ../leds/leds-lm3633.txt [3] ../regulator/lm363x-regulator.txt +[4] ../leds/leds-lm36274.txt lm3631@29 { compatible = "ti,lm3631"; @@ -90,7 +108,7 @@ lm3631@29 { lcd_bl { led-sources = <0 1>; - ramp-up-msec = <300>; + ramp-up-us = <300000>; }; }; }; @@ -152,15 +170,15 @@ lm3633@36 { main { label = "main_lcd"; led-sources = <1 2>; - ramp-up-msec = <500>; - ramp-down-msec = <500>; + ramp-up-us = <500000>; + ramp-down-us = <500000>; }; front { label = "front_lcd"; led-sources = <0>; - ramp-up-msec = <1000>; - ramp-down-msec = <0>; + ramp-up-us = <1000000>; + ramp-down-us = <0>; }; }; @@ -201,23 +219,51 @@ lm3695@63 { }; }; -lm3697@36 { - compatible = "ti,lm3697"; - reg = <0x36>; +lm36274@11 { + compatible = "ti,lm36274"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x11>; enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>; + regulators { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,lm363x-regulator"; - backlight { - compatible = "ti,lm3697-backlight"; + enable-gpios = <&pioC 0 GPIO_ACTIVE_HIGH>, + <&pioC 1 GPIO_ACTIVE_HIGH>; - lcd { - led-sources = <0 1 2>; - ramp-up-msec = <200>; - ramp-down-msec = <200>; + vboost { + regulator-name = "lcd_boost"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <7150000>; + regulator-always-on; + }; + + vpos { + regulator-name = "lcd_vpos"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6500000>; + }; + + vneg { + regulator-name = "lcd_vneg"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6500000>; }; }; - fault-monitor { - compatible = "ti,lm3697-fault-monitor"; + backlight { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,lm36274-backlight"; + + led@0 { + reg = <0>; + led-sources = <0 2>; + label = "white:backlight_cluster"; + linux,default-trigger = "backlight"; + }; }; }; |