diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mtd')
5 files changed, 82 insertions, 5 deletions
diff --git a/Documentation/devicetree/bindings/mtd/denali-nand.txt b/Documentation/devicetree/bindings/mtd/denali-nand.txt index 0ee8edb60efc..f33da8782741 100644 --- a/Documentation/devicetree/bindings/mtd/denali-nand.txt +++ b/Documentation/devicetree/bindings/mtd/denali-nand.txt @@ -8,6 +8,9 @@ Required properties: - reg : should contain registers location and length for data and reg. - reg-names: Should contain the reg names "nand_data" and "denali_reg" - interrupts : The interrupt number. + - clocks: should contain phandle of the controller core clock, the bus + interface clock, and the ECC circuit clock. + - clock-names: should contain "nand", "nand_x", "ecc" Optional properties: - nand-ecc-step-size: see nand.txt for details. If present, the value must be @@ -31,5 +34,7 @@ nand: nand@ff900000 { compatible = "altr,socfpga-denali-nand"; reg = <0xff900000 0x20>, <0xffb80000 0x1000>; reg-names = "nand_data", "denali_reg"; + clocks = <&nand_clk>, <&nand_x_clk>, <&nand_ecc_clk>; + clock-names = "nand", "nand_x", "ecc"; interrupts = <0 144 4>; }; diff --git a/Documentation/devicetree/bindings/mtd/nand.txt b/Documentation/devicetree/bindings/mtd/nand.txt index 8bb11d809429..e949c778e983 100644 --- a/Documentation/devicetree/bindings/mtd/nand.txt +++ b/Documentation/devicetree/bindings/mtd/nand.txt @@ -25,7 +25,7 @@ Optional NAND chip properties: Deprecated values: "soft_bch": use "soft" and nand-ecc-algo instead - nand-ecc-algo: string, algorithm of NAND ECC. - Supported values are: "hamming", "bch". + Valid values are: "hamming", "bch", "rs". - nand-bus-width : 8 or 16 bus width if not present 8 - nand-on-flash-bbt: boolean to enable on flash bbt option if not present false @@ -43,6 +43,10 @@ Optional NAND chip properties: This is particularly useful when only the in-band area is used by the upper layers, and you want to make your NAND as reliable as possible. +- nand-is-boot-medium: Whether the NAND chip is a boot medium. Drivers might use + this information to select ECC algorithms supported by + the boot ROM or similar restrictions. + - nand-rb: shall contain the native Ready/Busy ids. The ECC strength and ECC step size properties define the correction capability diff --git a/Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt b/Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt new file mode 100644 index 000000000000..b2f2ca12f9e6 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt @@ -0,0 +1,64 @@ +NVIDIA Tegra NAND Flash controller + +Required properties: +- compatible: Must be one of: + - "nvidia,tegra20-nand" +- reg: MMIO address range +- interrupts: interrupt output of the NFC controller +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - nand +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - nand + +Optional children nodes: +Individual NAND chips are children of the NAND controller node. Currently +only one NAND chip supported. + +Required children node properties: +- reg: An integer ranging from 1 to 6 representing the CS line to use. + +Optional children node properties: +- nand-ecc-mode: String, operation mode of the NAND ecc mode. Currently only + "hw" is supported. +- nand-ecc-algo: string, algorithm of NAND ECC. + Supported values with "hw" ECC mode are: "rs", "bch". +- nand-bus-width : See nand.txt +- nand-on-flash-bbt: See nand.txt +- nand-ecc-strength: integer representing the number of bits to correct + per ECC step (always 512). Supported strength using HW ECC + modes are: + - RS: 4, 6, 8 + - BCH: 4, 8, 14, 16 +- nand-ecc-maximize: See nand.txt +- nand-is-boot-medium: Makes sure only ECC strengths supported by the boot ROM + are chosen. +- wp-gpios: GPIO specifier for the write protect pin. + +Optional child node of NAND chip nodes: +Partitions: see partition.txt + + Example: + nand-controller@70008000 { + compatible = "nvidia,tegra20-nand"; + reg = <0x70008000 0x100>; + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA20_CLK_NDFLASH>; + clock-names = "nand"; + resets = <&tegra_car 13>; + reset-names = "nand"; + + nand@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + nand-bus-width = <8>; + nand-on-flash-bbt; + nand-ecc-algo = "bch"; + nand-ecc-strength = <8>; + wp-gpios = <&gpio TEGRA_GPIO(S, 0) GPIO_ACTIVE_LOW>; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt index 73d336befa08..1123cc6d56ef 100644 --- a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt +++ b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt @@ -45,11 +45,12 @@ Required properties: number (e.g., 0, 1, 2, etc.) - #address-cells: see partition.txt - #size-cells: see partition.txt -- nand-ecc-strength: see nand.txt -- nand-ecc-step-size: must be 512. see nand.txt for more details. Optional properties: - nand-bus-width: see nand.txt +- nand-ecc-strength: see nand.txt. If not specified, then ECC strength will + be used according to chip requirement and available + OOB size. Each nandcs device node may optionally contain a 'partitions' sub-node, which further contains sub-nodes describing the flash partition mapping. See @@ -77,7 +78,6 @@ nand-controller@1ac00000 { reg = <0>; nand-ecc-strength = <4>; - nand-ecc-step-size = <512>; nand-bus-width = <8>; partitions { @@ -117,7 +117,6 @@ nand-controller@79b0000 { nand@0 { reg = <0>; nand-ecc-strength = <4>; - nand-ecc-step-size = <512>; nand-bus-width = <8>; partitions { diff --git a/Documentation/devicetree/bindings/mtd/spi-nand.txt b/Documentation/devicetree/bindings/mtd/spi-nand.txt new file mode 100644 index 000000000000..8b51f3b6d55c --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/spi-nand.txt @@ -0,0 +1,5 @@ +SPI NAND flash + +Required properties: +- compatible: should be "spi-nand" +- reg: should encode the chip-select line used to access the NAND chip |