diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net')
22 files changed, 937 insertions, 320 deletions
diff --git a/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt deleted file mode 100644 index e15589f47787..000000000000 --- a/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt +++ /dev/null @@ -1,43 +0,0 @@ -* Broadcom UniMAC MDIO bus controller - -Required properties: -- compatible: should one from "brcm,genet-mdio-v1", "brcm,genet-mdio-v2", - "brcm,genet-mdio-v3", "brcm,genet-mdio-v4", "brcm,genet-mdio-v5" or - "brcm,unimac-mdio" -- reg: address and length of the register set for the device, first one is the - base register, and the second one is optional and for indirect accesses to - larger than 16-bits MDIO transactions -- reg-names: name(s) of the register must be "mdio" and optional "mdio_indir_rw" -- #size-cells: must be 1 -- #address-cells: must be 0 - -Optional properties: -- interrupts: must be one if the interrupt is shared with the Ethernet MAC or - Ethernet switch this MDIO block is integrated from, or must be two, if there - are two separate interrupts, first one must be "mdio done" and second must be - for "mdio error" -- interrupt-names: must be "mdio_done_error" when there is a share interrupt fed - to this hardware block, or must be "mdio_done" for the first interrupt and - "mdio_error" for the second when there are separate interrupts -- clocks: A reference to the clock supplying the MDIO bus controller -- clock-frequency: the MDIO bus clock that must be output by the MDIO bus - hardware, if absent, the default hardware values are used - -Child nodes of this MDIO bus controller node are standard Ethernet PHY device -nodes as described in Documentation/devicetree/bindings/net/phy.txt - -Example: - -mdio@403c0 { - compatible = "brcm,unimac-mdio"; - reg = <0x403c0 0x8 0x40300 0x18>; - reg-names = "mdio", "mdio_indir_rw"; - #size-cells = <1>; - #address-cells = <0>; - - ... - phy@0 { - compatible = "ethernet-phy-ieee802.3-c22"; - reg = <0>; - }; -}; diff --git a/Documentation/devicetree/bindings/net/brcm,unimac-mdio.yaml b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.yaml new file mode 100644 index 000000000000..f4f4c37f1d4e --- /dev/null +++ b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.yaml @@ -0,0 +1,84 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/brcm,unimac-mdio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom UniMAC MDIO bus controller + +maintainers: + - Rafał Miłecki <rafal@milecki.pl> + +allOf: + - $ref: mdio.yaml# + +properties: + compatible: + enum: + - brcm,genet-mdio-v1 + - brcm,genet-mdio-v2 + - brcm,genet-mdio-v3 + - brcm,genet-mdio-v4 + - brcm,genet-mdio-v5 + - brcm,unimac-mdio + + reg: + minItems: 1 + items: + - description: base register + - description: indirect accesses to larger than 16-bits MDIO transactions + + reg-names: + minItems: 1 + items: + - const: mdio + - const: mdio_indir_rw + + interrupts: + oneOf: + - description: > + Interrupt shared with the Ethernet MAC or Ethernet switch this MDIO + block is integrated from + - items: + - description: | + "mdio done" interrupt + - description: | + "mdio error" interrupt + + interrupt-names: + oneOf: + - const: mdio_done_error + - items: + - const: mdio_done + - const: mdio_error + + clocks: + description: A reference to the clock supplying the MDIO bus controller + + clock-frequency: + description: > + The MDIO bus clock that must be output by the MDIO bus hardware, if + absent, the default hardware values are used + +unevaluatedProperties: false + +required: + - reg + - reg-names + - '#address-cells' + - '#size-cells' + +examples: + - | + mdio@403c0 { + compatible = "brcm,unimac-mdio"; + reg = <0x403c0 0x8>, <0x40300 0x18>; + reg-names = "mdio", "mdio_indir_rw"; + #address-cells = <1>; + #size-cells = <0>; + + ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/can/bosch,c_can.yaml b/Documentation/devicetree/bindings/net/can/bosch,c_can.yaml new file mode 100644 index 000000000000..2cd145a642f1 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/bosch,c_can.yaml @@ -0,0 +1,119 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/can/bosch,c_can.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Bosch C_CAN/D_CAN controller Device Tree Bindings + +description: Bosch C_CAN/D_CAN controller for CAN bus + +maintainers: + - Dario Binacchi <dariobin@libero.it> + +allOf: + - $ref: can-controller.yaml# + +properties: + compatible: + oneOf: + - enum: + - bosch,c_can + - bosch,d_can + - ti,dra7-d_can + - ti,am3352-d_can + - items: + - enum: + - ti,am4372-d_can + - const: ti,am3352-d_can + + reg: + maxItems: 1 + + interrupts: + minItems: 1 + maxItems: 4 + + power-domains: + description: | + Should contain a phandle to a PM domain provider node and an args + specifier containing the DCAN device id value. It's mandatory for + Keystone 2 66AK2G SoCs only. + maxItems: 1 + + clocks: + description: | + CAN functional clock phandle. + maxItems: 1 + + clock-names: + maxItems: 1 + + syscon-raminit: + description: | + Handle to system control region that contains the RAMINIT register, + register offset to the RAMINIT register and the CAN instance number (0 + offset). + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + items: + - description: The phandle to the system control region. + - description: The register offset. + - description: The CAN instance number. + + resets: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + +if: + properties: + compatible: + contains: + enum: + - bosch,d_can + +then: + properties: + interrupts: + minItems: 4 + maxItems: 4 + items: + - description: Error and status IRQ + - description: Message object IRQ + - description: RAM ECC correctable error IRQ + - description: RAM ECC non-correctable error IRQ + +else: + properties: + interrupts: + maxItems: 1 + items: + - description: Error and status IRQ + +additionalProperties: false + +examples: + - | + #include <dt-bindings/reset/altr,rst-mgr.h> + + can@ffc00000 { + compatible = "bosch,d_can"; + reg = <0xffc00000 0x1000>; + interrupts = <0 131 4>, <0 132 4>, <0 133 4>, <0 134 4>; + clocks = <&can0_clk>; + resets = <&rst CAN0_RESET>; + }; + - | + can@0 { + compatible = "ti,am3352-d_can"; + reg = <0x0 0x2000>; + clocks = <&dcan1_fck>; + clock-names = "fck"; + syscon-raminit = <&scm_conf 0x644 1>; + interrupts = <55>; + }; diff --git a/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml b/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml index f84e31348d80..fb547e26c676 100644 --- a/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml +++ b/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml @@ -104,9 +104,18 @@ properties: maximum: 32 maxItems: 1 + power-domains: + description: + Power domain provider node and an args specifier containing + the can device id value. + maxItems: 1 + can-transceiver: $ref: can-transceiver.yaml# + phys: + maxItems: 1 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/net/can/c_can.txt b/Documentation/devicetree/bindings/net/can/c_can.txt deleted file mode 100644 index 366479806acb..000000000000 --- a/Documentation/devicetree/bindings/net/can/c_can.txt +++ /dev/null @@ -1,65 +0,0 @@ -Bosch C_CAN/D_CAN controller Device Tree Bindings -------------------------------------------------- - -Required properties: -- compatible : Should be "bosch,c_can" for C_CAN controllers and - "bosch,d_can" for D_CAN controllers. - Can be "ti,dra7-d_can", "ti,am3352-d_can" or - "ti,am4372-d_can". -- reg : physical base address and size of the C_CAN/D_CAN - registers map -- interrupts : property with a value describing the interrupt - number - -The following are mandatory properties for DRA7x, AM33xx and AM43xx SoCs only: -- ti,hwmods : Must be "d_can<n>" or "c_can<n>", n being the - instance number - -The following are mandatory properties for Keystone 2 66AK2G SoCs only: -- power-domains : Should contain a phandle to a PM domain provider node - and an args specifier containing the DCAN device id - value. This property is as per the binding, - Documentation/devicetree/bindings/soc/ti/sci-pm-domain.yaml -- clocks : CAN functional clock phandle. This property is as per the - binding, - Documentation/devicetree/bindings/clock/ti,sci-clk.yaml - -Optional properties: -- syscon-raminit : Handle to system control region that contains the - RAMINIT register, register offset to the RAMINIT - register and the CAN instance number (0 offset). - -Note: "ti,hwmods" field is used to fetch the base address and irq -resources from TI, omap hwmod data base during device registration. -Future plan is to migrate hwmod data base contents into device tree -blob so that, all the required data will be used from device tree dts -file. - -Example: - -Step1: SoC common .dtsi file - - dcan1: d_can@481d0000 { - compatible = "bosch,d_can"; - reg = <0x481d0000 0x2000>; - interrupts = <55>; - interrupt-parent = <&intc>; - status = "disabled"; - }; - -(or) - - dcan1: d_can@481d0000 { - compatible = "bosch,d_can"; - ti,hwmods = "d_can1"; - reg = <0x481d0000 0x2000>; - interrupts = <55>; - interrupt-parent = <&intc>; - status = "disabled"; - }; - -Step 2: board specific .dts file - - &dcan1 { - status = "okay"; - }; diff --git a/Documentation/devicetree/bindings/net/can/can-controller.yaml b/Documentation/devicetree/bindings/net/can/can-controller.yaml index 9cf2ae097156..1f0e98051074 100644 --- a/Documentation/devicetree/bindings/net/can/can-controller.yaml +++ b/Documentation/devicetree/bindings/net/can/can-controller.yaml @@ -13,6 +13,15 @@ properties: $nodename: pattern: "^can(@.*)?$" + termination-gpios: + description: GPIO pin to enable CAN bus termination. + maxItems: 1 + + termination-ohms: + description: The resistance value of the CAN bus termination resistor. + minimum: 1 + maximum: 65535 + additionalProperties: true ... diff --git a/Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml b/Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml index 55bff1586b6f..3f0ee17c1461 100644 --- a/Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml +++ b/Documentation/devicetree/bindings/net/can/fsl,flexcan.yaml @@ -119,6 +119,9 @@ properties: minimum: 0 maximum: 2 + termination-gpios: true + termination-ohms: true + required: - compatible - reg @@ -148,3 +151,17 @@ examples: fsl,stop-mode = <&gpr 0x34 28>; fsl,scu-index = /bits/ 8 <1>; }; + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + + can@2090000 { + compatible = "fsl,imx6q-flexcan"; + reg = <0x02090000 0x4000>; + interrupts = <0 110 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks 1>, <&clks 2>; + clock-names = "ipg", "per"; + fsl,stop-mode = <&gpr 0x34 28>; + termination-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; + termination-ohms = <120>; + }; diff --git a/Documentation/devicetree/bindings/net/can/renesas,rcar-canfd.yaml b/Documentation/devicetree/bindings/net/can/renesas,rcar-canfd.yaml index 0b33ba9ccb47..546c6e6d2fb0 100644 --- a/Documentation/devicetree/bindings/net/can/renesas,rcar-canfd.yaml +++ b/Documentation/devicetree/bindings/net/can/renesas,rcar-canfd.yaml @@ -30,13 +30,15 @@ properties: - renesas,r8a77995-canfd # R-Car D3 - const: renesas,rcar-gen3-canfd # R-Car Gen3 and RZ/G2 + - items: + - enum: + - renesas,r9a07g044-canfd # RZ/G2{L,LC} + - const: renesas,rzg2l-canfd # RZ/G2L family + reg: maxItems: 1 - interrupts: - items: - - description: Channel interrupt - - description: Global interrupt + interrupts: true clocks: maxItems: 3 @@ -50,8 +52,7 @@ properties: power-domains: maxItems: 1 - resets: - maxItems: 1 + resets: true renesas,no-can-fd: $ref: /schemas/types.yaml#/definitions/flag @@ -91,6 +92,62 @@ required: - channel0 - channel1 +if: + properties: + compatible: + contains: + enum: + - renesas,rzg2l-canfd +then: + properties: + interrupts: + items: + - description: CAN global error interrupt + - description: CAN receive FIFO interrupt + - description: CAN0 error interrupt + - description: CAN0 transmit interrupt + - description: CAN0 transmit/receive FIFO receive completion interrupt + - description: CAN1 error interrupt + - description: CAN1 transmit interrupt + - description: CAN1 transmit/receive FIFO receive completion interrupt + + interrupt-names: + items: + - const: g_err + - const: g_recc + - const: ch0_err + - const: ch0_rec + - const: ch0_trx + - const: ch1_err + - const: ch1_rec + - const: ch1_trx + + resets: + maxItems: 2 + + reset-names: + items: + - const: rstp_n + - const: rstc_n + + required: + - interrupt-names + - reset-names +else: + properties: + interrupts: + items: + - description: Channel interrupt + - description: Global interrupt + + interrupt-names: + items: + - const: ch_int + - const: g_int + + resets: + maxItems: 1 + unevaluatedProperties: false examples: diff --git a/Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml b/Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml index 0b8a05dd52e6..f978f8719d8e 100644 --- a/Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml +++ b/Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml @@ -67,8 +67,8 @@ properties: reg: oneOf: - enum: - - 0 - - 1 + - 0 + - 1 required: - compatible diff --git a/Documentation/devicetree/bindings/net/fsl,fec.yaml b/Documentation/devicetree/bindings/net/fsl,fec.yaml new file mode 100644 index 000000000000..eca41443fcce --- /dev/null +++ b/Documentation/devicetree/bindings/net/fsl,fec.yaml @@ -0,0 +1,244 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/fsl,fec.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale Fast Ethernet Controller (FEC) + +maintainers: + - Joakim Zhang <qiangqing.zhang@nxp.com> + +allOf: + - $ref: ethernet-controller.yaml# + +properties: + compatible: + oneOf: + - enum: + - fsl,imx25-fec + - fsl,imx27-fec + - fsl,imx28-fec + - fsl,imx6q-fec + - fsl,mvf600-fec + - items: + - enum: + - fsl,imx53-fec + - fsl,imx6sl-fec + - const: fsl,imx25-fec + - items: + - enum: + - fsl,imx35-fec + - fsl,imx51-fec + - const: fsl,imx27-fec + - items: + - enum: + - fsl,imx6ul-fec + - fsl,imx6sx-fec + - const: fsl,imx6q-fec + - items: + - enum: + - fsl,imx7d-fec + - const: fsl,imx6sx-fec + - items: + - const: fsl,imx8mq-fec + - const: fsl,imx6sx-fec + - items: + - enum: + - fsl,imx8mm-fec + - fsl,imx8mn-fec + - fsl,imx8mp-fec + - const: fsl,imx8mq-fec + - const: fsl,imx6sx-fec + - items: + - const: fsl,imx8qm-fec + - const: fsl,imx6sx-fec + - items: + - enum: + - fsl,imx8qxp-fec + - const: fsl,imx8qm-fec + - const: fsl,imx6sx-fec + + reg: + maxItems: 1 + + interrupts: + minItems: 1 + maxItems: 4 + + interrupt-names: + oneOf: + - items: + - const: int0 + - items: + - const: int0 + - const: pps + - items: + - const: int0 + - const: int1 + - const: int2 + - items: + - const: int0 + - const: int1 + - const: int2 + - const: pps + + clocks: + minItems: 2 + maxItems: 5 + description: + The "ipg", for MAC ipg_clk_s, ipg_clk_mac_s that are for register accessing. + The "ahb", for MAC ipg_clk, ipg_clk_mac that are bus clock. + The "ptp"(option), for IEEE1588 timer clock that requires the clock. + The "enet_clk_ref"(option), for MAC transmit/receiver reference clock like + RGMII TXC clock or RMII reference clock. It depends on board design, + the clock is required if RGMII TXC and RMII reference clock source from + SOC internal PLL. + The "enet_out"(option), output clock for external device, like supply clock + for PHY. The clock is required if PHY clock source from SOC. + The "enet_2x_txclk"(option), for RGMII sampling clock which fixed at 250Mhz. + The clock is required if SoC RGMII enable clock delay. + + clock-names: + minItems: 2 + maxItems: 5 + items: + enum: + - ipg + - ahb + - ptp + - enet_clk_ref + - enet_out + - enet_2x_txclk + + phy-mode: true + + phy-handle: true + + fixed-link: true + + local-mac-address: true + + mac-address: true + + tx-internal-delay-ps: + enum: [0, 2000] + + rx-internal-delay-ps: + enum: [0, 2000] + + phy-supply: + description: + Regulator that powers the Ethernet PHY. + + fsl,num-tx-queues: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + The property is valid for enet-avb IP, which supports hw multi queues. + Should specify the tx queue number, otherwise set tx queue number to 1. + enum: [1, 2, 3] + + fsl,num-rx-queues: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + The property is valid for enet-avb IP, which supports hw multi queues. + Should specify the rx queue number, otherwise set rx queue number to 1. + enum: [1, 2, 3] + + fsl,magic-packet: + $ref: /schemas/types.yaml#/definitions/flag + description: + If present, indicates that the hardware supports waking up via magic packet. + + fsl,err006687-workaround-present: + $ref: /schemas/types.yaml#/definitions/flag + description: + If present indicates that the system has the hardware workaround for + ERR006687 applied and does not need a software workaround. + + fsl,stop-mode: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: + Register bits of stop mode control, the format is <&gpr req_gpr req_bit>. + gpr is the phandle to general purpose register node. + req_gpr is the gpr register offset for ENET stop request. + req_bit is the gpr bit offset for ENET stop request. + + mdio: + type: object + description: + Specifies the mdio bus in the FEC, used as a container for phy nodes. + + # Deprecated optional properties: + # To avoid these, create a phy node according to ethernet-phy.yaml in the same + # directory, and point the FEC's "phy-handle" property to it. Then use + # the phy's reset binding, again described by ethernet-phy.yaml. + + phy-reset-gpios: + deprecated: true + description: + Should specify the gpio for phy reset. + + phy-reset-duration: + deprecated: true + description: + Reset duration in milliseconds. Should present only if property + "phy-reset-gpios" is available. Missing the property will have the + duration be 1 millisecond. Numbers greater than 1000 are invalid + and 1 millisecond will be used instead. + + phy-reset-active-high: + deprecated: true + description: + If present then the reset sequence using the GPIO specified in the + "phy-reset-gpios" property is reversed (H=reset state, L=operation state). + + phy-reset-post-delay: + deprecated: true + description: + Post reset delay in milliseconds. If present then a delay of phy-reset-post-delay + milliseconds will be observed after the phy-reset-gpios has been toggled. + Can be omitted thus no delay is observed. Delay is in range of 1ms to 1000ms. + Other delays are invalid. + +required: + - compatible + - reg + - interrupts + +# FIXME: We had better set additionalProperties to false to avoid invalid or at +# least undocumented properties. However, PHY may have a deprecated option to +# place PHY OF properties in the MAC node, such as Micrel PHY, and we can find +# these boards which is based on i.MX6QDL. +additionalProperties: false + +examples: + - | + ethernet@83fec000 { + compatible = "fsl,imx51-fec", "fsl,imx27-fec"; + reg = <0x83fec000 0x4000>; + interrupts = <87>; + phy-mode = "mii"; + phy-reset-gpios = <&gpio2 14 0>; + phy-supply = <®_fec_supply>; + }; + + ethernet@83fed000 { + compatible = "fsl,imx51-fec", "fsl,imx27-fec"; + reg = <0x83fed000 0x4000>; + interrupts = <87>; + phy-mode = "mii"; + phy-reset-gpios = <&gpio2 14 0>; + phy-supply = <®_fec_supply>; + phy-handle = <ðphy0>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt deleted file mode 100644 index 9b543789cd52..000000000000 --- a/Documentation/devicetree/bindings/net/fsl-fec.txt +++ /dev/null @@ -1,95 +0,0 @@ -* Freescale Fast Ethernet Controller (FEC) - -Required properties: -- compatible : Should be "fsl,<soc>-fec" -- reg : Address and length of the register set for the device -- interrupts : Should contain fec interrupt -- phy-mode : See ethernet.txt file in the same directory - -Optional properties: -- phy-supply : regulator that powers the Ethernet PHY. -- phy-handle : phandle to the PHY device connected to this device. -- fixed-link : Assume a fixed link. See fixed-link.txt in the same directory. - Use instead of phy-handle. -- fsl,num-tx-queues : The property is valid for enet-avb IP, which supports - hw multi queues. Should specify the tx queue number, otherwise set tx queue - number to 1. -- fsl,num-rx-queues : The property is valid for enet-avb IP, which supports - hw multi queues. Should specify the rx queue number, otherwise set rx queue - number to 1. -- fsl,magic-packet : If present, indicates that the hardware supports waking - up via magic packet. -- fsl,err006687-workaround-present: If present indicates that the system has - the hardware workaround for ERR006687 applied and does not need a software - workaround. -- fsl,stop-mode: register bits of stop mode control, the format is - <&gpr req_gpr req_bit>. - gpr is the phandle to general purpose register node. - req_gpr is the gpr register offset for ENET stop request. - req_bit is the gpr bit offset for ENET stop request. - -interrupt-names: names of the interrupts listed in interrupts property in - the same order. The defaults if not specified are - __Number of interrupts__ __Default__ - 1 "int0" - 2 "int0", "pps" - 3 "int0", "int1", "int2" - 4 "int0", "int1", "int2", "pps" - The order may be changed as long as they correspond to the interrupts - property. Currently, only i.mx7 uses "int1" and "int2". They correspond to - tx/rx queues 1 and 2. "int0" will be used for queue 0 and ENET_MII interrupts. - For imx6sx, "int0" handles all 3 queues and ENET_MII. "pps" is for the pulse - per second interrupt associated with 1588 precision time protocol(PTP). - -Optional subnodes: -- mdio : specifies the mdio bus in the FEC, used as a container for phy nodes - according to phy.txt in the same directory - -Deprecated optional properties: - To avoid these, create a phy node according to phy.txt in the same - directory, and point the fec's "phy-handle" property to it. Then use - the phy's reset binding, again described by phy.txt. -- phy-reset-gpios : Should specify the gpio for phy reset -- phy-reset-duration : Reset duration in milliseconds. Should present - only if property "phy-reset-gpios" is available. Missing the property - will have the duration be 1 millisecond. Numbers greater than 1000 are - invalid and 1 millisecond will be used instead. -- phy-reset-active-high : If present then the reset sequence using the GPIO - specified in the "phy-reset-gpios" property is reversed (H=reset state, - L=operation state). -- phy-reset-post-delay : Post reset delay in milliseconds. If present then - a delay of phy-reset-post-delay milliseconds will be observed after the - phy-reset-gpios has been toggled. Can be omitted thus no delay is - observed. Delay is in range of 1ms to 1000ms. Other delays are invalid. - -Example: - -ethernet@83fec000 { - compatible = "fsl,imx51-fec", "fsl,imx27-fec"; - reg = <0x83fec000 0x4000>; - interrupts = <87>; - phy-mode = "mii"; - phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>; /* GPIO2_14 */ - local-mac-address = [00 04 9F 01 1B B9]; - phy-supply = <®_fec_supply>; -}; - -Example with phy specified: - -ethernet@83fec000 { - compatible = "fsl,imx51-fec", "fsl,imx27-fec"; - reg = <0x83fec000 0x4000>; - interrupts = <87>; - phy-mode = "mii"; - phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>; /* GPIO2_14 */ - local-mac-address = [00 04 9F 01 1B B9]; - phy-supply = <®_fec_supply>; - phy-handle = <ðphy>; - mdio { - clock-frequency = <5000000>; - ethphy: ethernet-phy@6 { - compatible = "ethernet-phy-ieee802.3-c22"; - reg = <6>; - max-speed = <100>; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/net/gpmc-eth.txt b/Documentation/devicetree/bindings/net/gpmc-eth.txt index f7da3d73ca1b..32821066a85b 100644 --- a/Documentation/devicetree/bindings/net/gpmc-eth.txt +++ b/Documentation/devicetree/bindings/net/gpmc-eth.txt @@ -13,7 +13,7 @@ Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt For the properties relevant to the ethernet controller connected to the GPMC refer to the binding documentation of the device. For example, the documentation -for the SMSC 911x is Documentation/devicetree/bindings/net/smsc911x.txt +for the SMSC 911x is Documentation/devicetree/bindings/net/smsc,lan9115.yaml Child nodes need to specify the GPMC bus address width using the "bank-width" property but is possible that an ethernet controller also has a property to diff --git a/Documentation/devicetree/bindings/net/imx-dwmac.txt b/Documentation/devicetree/bindings/net/imx-dwmac.txt deleted file mode 100644 index 921d522fe8d7..000000000000 --- a/Documentation/devicetree/bindings/net/imx-dwmac.txt +++ /dev/null @@ -1,56 +0,0 @@ -IMX8 glue layer controller, NXP imx8 families support Synopsys MAC 5.10a IP. - -This file documents platform glue layer for IMX. -Please see stmmac.txt for the other unchanged properties. - -The device node has following properties. - -Required properties: -- compatible: Should be "nxp,imx8mp-dwmac-eqos" to select glue layer - and "snps,dwmac-5.10a" to select IP version. -- clocks: Must contain a phandle for each entry in clock-names. -- clock-names: Should be "stmmaceth" for the host clock. - Should be "pclk" for the MAC apb clock. - Should be "ptp_ref" for the MAC timer clock. - Should be "tx" for the MAC RGMII TX clock: - Should be "mem" for EQOS MEM clock. - - "mem" clock is required for imx8dxl platform. - - "mem" clock is not required for imx8mp platform. -- interrupt-names: Should contain a list of interrupt names corresponding to - the interrupts in the interrupts property, if available. - Should be "macirq" for the main MAC IRQ - Should be "eth_wake_irq" for the IT which wake up system -- intf_mode: Should be phandle/offset pair. The phandle to the syscon node which - encompases the GPR register, and the offset of the GPR register. - - required for imx8mp platform. - - is optional for imx8dxl platform. - -Optional properties: -- intf_mode: is optional for imx8dxl platform. -- snps,rmii_refclk_ext: to select RMII reference clock from external. - -Example: - eqos: ethernet@30bf0000 { - compatible = "nxp,imx8mp-dwmac-eqos", "snps,dwmac-5.10a"; - reg = <0x30bf0000 0x10000>; - interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "eth_wake_irq", "macirq"; - clocks = <&clk IMX8MP_CLK_ENET_QOS_ROOT>, - <&clk IMX8MP_CLK_QOS_ENET_ROOT>, - <&clk IMX8MP_CLK_ENET_QOS_TIMER>, - <&clk IMX8MP_CLK_ENET_QOS>; - clock-names = "stmmaceth", "pclk", "ptp_ref", "tx"; - assigned-clocks = <&clk IMX8MP_CLK_ENET_AXI>, - <&clk IMX8MP_CLK_ENET_QOS_TIMER>, - <&clk IMX8MP_CLK_ENET_QOS>; - assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_266M>, - <&clk IMX8MP_SYS_PLL2_100M>, - <&clk IMX8MP_SYS_PLL2_125M>; - assigned-clock-rates = <0>, <100000000>, <125000000>; - nvmem-cells = <ð_mac0>; - nvmem-cell-names = "mac-address"; - nvmem_macaddr_swap; - intf_mode = <&gpr 0x4>; - status = "disabled"; - }; diff --git a/Documentation/devicetree/bindings/net/intel,ixp46x-ptp-timer.yaml b/Documentation/devicetree/bindings/net/intel,ixp46x-ptp-timer.yaml new file mode 100644 index 000000000000..8b9b3f915d92 --- /dev/null +++ b/Documentation/devicetree/bindings/net/intel,ixp46x-ptp-timer.yaml @@ -0,0 +1,54 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2018 Linaro Ltd. +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/net/intel,ixp46x-ptp-timer.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Intel IXP46x PTP Timer (TSYNC) + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +description: | + The Intel IXP46x PTP timer is known in the manual as IEEE1588 Hardware + Assist and Time Synchronization Hardware Assist TSYNC provides a PTP + timer. It exists in the Intel IXP45x and IXP46x XScale SoCs. + +properties: + compatible: + const: intel,ixp46x-ptp-timer + + reg: + maxItems: 1 + + interrupts: + items: + - description: Interrupt to trigger master mode snapshot from the + PRP timer, usually a GPIO interrupt. + - description: Interrupt to trigger slave mode snapshot from the + PRP timer, usually a GPIO interrupt. + + interrupt-names: + items: + - const: master + - const: slave + +required: + - compatible + - reg + - interrupts + - interrupt-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + ptp-timer@c8010000 { + compatible = "intel,ixp46x-ptp-timer"; + reg = <0xc8010000 0x1000>; + interrupt-parent = <&gpio0>; + interrupts = <8 IRQ_TYPE_EDGE_FALLING>, <7 IRQ_TYPE_EDGE_FALLING>; + interrupt-names = "master", "slave"; + }; diff --git a/Documentation/devicetree/bindings/net/litex,liteeth.yaml b/Documentation/devicetree/bindings/net/litex,liteeth.yaml new file mode 100644 index 000000000000..76c164a8199a --- /dev/null +++ b/Documentation/devicetree/bindings/net/litex,liteeth.yaml @@ -0,0 +1,98 @@ +# SPDX-License-Identifier: GPL-2.0-or-later OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/litex,liteeth.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: LiteX LiteETH ethernet device + +maintainers: + - Joel Stanley <joel@jms.id.au> + +description: | + LiteETH is a small footprint and configurable Ethernet core for FPGA based + system on chips. + + The hardware source is Open Source and can be found on at + https://github.com/enjoy-digital/liteeth/. + +allOf: + - $ref: ethernet-controller.yaml# + +properties: + compatible: + const: litex,liteeth + + reg: + items: + - description: MAC registers + - description: MDIO registers + - description: Packet buffer + + reg-names: + items: + - const: mac + - const: mdio + - const: buffer + + interrupts: + maxItems: 1 + + litex,rx-slots: + description: Number of slots in the receive buffer + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + default: 2 + + litex,tx-slots: + description: Number of slots in the transmit buffer + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + default: 2 + + litex,slot-size: + description: Size in bytes of a slot in the tx/rx buffer + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0x800 + default: 0x800 + + mac-address: true + local-mac-address: true + phy-handle: true + + mdio: + $ref: mdio.yaml# + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + mac: ethernet@8020000 { + compatible = "litex,liteeth"; + reg = <0x8021000 0x100>, + <0x8020800 0x100>, + <0x8030000 0x2000>; + reg-names = "mac", "mdio", "buffer"; + litex,rx-slots = <2>; + litex,tx-slots = <2>; + litex,slot-size = <0x800>; + interrupts = <0x11 0x1>; + phy-handle = <ð_phy>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + eth_phy: ethernet-phy@0 { + reg = <0>; + }; + }; + }; +... + +# vim: set ts=2 sw=2 sts=2 tw=80 et cc=80 ft=yaml : diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt index a4d547efc32a..af9df2f01a1c 100644 --- a/Documentation/devicetree/bindings/net/macb.txt +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -8,6 +8,7 @@ Required properties: Use "cdns,np4-macb" for NP4 SoC devices. Use "cdns,at32ap7000-macb" for other 10/100 usage or use the generic form: "cdns,macb". Use "atmel,sama5d2-gem" for the GEM IP (10/100) available on Atmel sama5d2 SoCs. + Use "atmel,sama5d29-gem" for GEM XL IP (10/100) available on Atmel sama5d29 SoCs. Use "atmel,sama5d3-macb" for the 10/100Mbit IP available on Atmel sama5d3 SoCs. Use "atmel,sama5d3-gem" for the Gigabit IP available on Atmel sama5d3 SoCs. Use "atmel,sama5d4-gem" for the GEM IP (10/100) available on Atmel sama5d4 SoCs. diff --git a/Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml b/Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml new file mode 100644 index 000000000000..5629b2e4ccf8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml @@ -0,0 +1,93 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/nxp,dwmac-imx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP i.MX8 DWMAC glue layer Device Tree Bindings + +maintainers: + - Joakim Zhang <qiangqing.zhang@nxp.com> + +# We need a select here so we don't match all nodes with 'snps,dwmac' +select: + properties: + compatible: + contains: + enum: + - nxp,imx8mp-dwmac-eqos + - nxp,imx8dxl-dwmac-eqos + required: + - compatible + +allOf: + - $ref: "snps,dwmac.yaml#" + +properties: + compatible: + oneOf: + - items: + - enum: + - nxp,imx8mp-dwmac-eqos + - nxp,imx8dxl-dwmac-eqos + - const: snps,dwmac-5.10a + + clocks: + minItems: 3 + maxItems: 5 + items: + - description: MAC host clock + - description: MAC apb clock + - description: MAC timer clock + - description: MAC RGMII TX clock + - description: EQOS MEM clock + + clock-names: + minItems: 3 + maxItems: 5 + contains: + enum: + - stmmaceth + - pclk + - ptp_ref + - tx + - mem + + intf_mode: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: + Should be phandle/offset pair. The phandle to the syscon node which + encompases the GPR register, and the offset of the GPR register. + + snps,rmii_refclk_ext: + $ref: /schemas/types.yaml#/definitions/flag + description: + To select RMII reference clock from external. + +required: + - compatible + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/clock/imx8mp-clock.h> + + eqos: ethernet@30bf0000 { + compatible = "nxp,imx8mp-dwmac-eqos","snps,dwmac-5.10a"; + reg = <0x30bf0000 0x10000>; + interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq", "eth_wake_irq"; + clocks = <&clk IMX8MP_CLK_ENET_QOS_ROOT>, + <&clk IMX8MP_CLK_QOS_ENET_ROOT>, + <&clk IMX8MP_CLK_ENET_QOS_TIMER>, + <&clk IMX8MP_CLK_ENET_QOS>; + clock-names = "stmmaceth", "pclk", "ptp_ref", "tx"; + phy-mode = "rgmii"; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/net/qcom,ipa.yaml b/Documentation/devicetree/bindings/net/qcom,ipa.yaml index ed88ba4b94df..b8a0b392b24e 100644 --- a/Documentation/devicetree/bindings/net/qcom,ipa.yaml +++ b/Documentation/devicetree/bindings/net/qcom,ipa.yaml @@ -87,16 +87,24 @@ properties: - const: ipa-setup-ready interconnects: - items: - - description: Interconnect path between IPA and main memory - - description: Interconnect path between IPA and internal memory - - description: Interconnect path between IPA and the AP subsystem + oneOf: + - items: + - description: Path leading to system memory + - description: Path between the AP and IPA config space + - items: + - description: Path leading to system memory + - description: Path leading to internal memory + - description: Path between the AP and IPA config space interconnect-names: - items: - - const: memory - - const: imem - - const: config + oneOf: + - items: + - const: memory + - const: config + - items: + - const: memory + - const: imem + - const: config qcom,smem-states: $ref: /schemas/types.yaml#/definitions/phandle-array diff --git a/Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml b/Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml index 0c973310ada0..2af304341772 100644 --- a/Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml +++ b/Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml @@ -14,7 +14,9 @@ allOf: properties: compatible: - const: qcom,ipq4019-mdio + enum: + - qcom,ipq4019-mdio + - qcom,ipq5018-mdio "#address-cells": const: 1 @@ -23,7 +25,18 @@ properties: const: 0 reg: + minItems: 1 + maxItems: 2 + description: + the first Address and length of the register set for the MDIO controller. + the second Address and length of the register for ethernet LDO, this second + address range is only required by the platform IPQ50xx. + + clocks: maxItems: 1 + description: | + MDIO clock source frequency fixed to 100MHZ, this clock should be specified + by the platform IPQ807x, IPQ60xx and IPQ50xx. required: - compatible diff --git a/Documentation/devicetree/bindings/net/smsc,lan9115.yaml b/Documentation/devicetree/bindings/net/smsc,lan9115.yaml new file mode 100644 index 000000000000..f86667cbcca8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/smsc,lan9115.yaml @@ -0,0 +1,110 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/smsc,lan9115.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Smart Mixed-Signal Connectivity (SMSC) LAN911x/912x Controller + +maintainers: + - Shawn Guo <shawnguo@kernel.org> + +allOf: + - $ref: ethernet-controller.yaml# + +properties: + compatible: + oneOf: + - const: smsc,lan9115 + - items: + - enum: + - smsc,lan89218 + - smsc,lan9117 + - smsc,lan9118 + - smsc,lan9220 + - smsc,lan9221 + - const: smsc,lan9115 + + reg: + maxItems: 1 + + reg-shift: true + + reg-io-width: + enum: [ 2, 4 ] + default: 2 + + interrupts: + minItems: 1 + items: + - description: + LAN interrupt line + - description: + Optional PME (power management event) interrupt that is able to wake + up the host system with a 50ms pulse on network activity + + clocks: + maxItems: 1 + + phy-mode: true + + smsc,irq-active-high: + type: boolean + description: Indicates the IRQ polarity is active-high + + smsc,irq-push-pull: + type: boolean + description: Indicates the IRQ type is push-pull + + smsc,force-internal-phy: + type: boolean + description: Forces SMSC LAN controller to use internal PHY + + smsc,force-external-phy: + type: boolean + description: Forces SMSC LAN controller to use external PHY + + smsc,save-mac-address: + type: boolean + description: + Indicates that MAC address needs to be saved before resetting the + controller + + reset-gpios: + maxItems: 1 + description: + A GPIO line connected to the RESET (active low) signal of the device. + On many systems this is wired high so the device goes out of reset at + power-on, but if it is under program control, this optional GPIO can + wake up in response to it. + + vdd33a-supply: + description: 3.3V analog power supply + + vddvario-supply: + description: IO logic power supply + +required: + - compatible + - reg + - interrupts + +# There are lots of bus-specific properties ("qcom,*", "samsung,*", "fsl,*", +# "gpmc,*", ...) to be found, that actually depend on the compatible value of +# the parent node. +additionalProperties: true + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + ethernet@f4000000 { + compatible = "smsc,lan9220", "smsc,lan9115"; + reg = <0xf4000000 0x2000000>; + phy-mode = "mii"; + interrupt-parent = <&gpio1>; + interrupts = <31>, <32>; + reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; + reg-io-width = <4>; + smsc,irq-push-pull; + }; diff --git a/Documentation/devicetree/bindings/net/smsc911x.txt b/Documentation/devicetree/bindings/net/smsc911x.txt deleted file mode 100644 index acfafc8e143c..000000000000 --- a/Documentation/devicetree/bindings/net/smsc911x.txt +++ /dev/null @@ -1,43 +0,0 @@ -* Smart Mixed-Signal Connectivity (SMSC) LAN911x/912x Controller - -Required properties: -- compatible : Should be "smsc,lan<model>", "smsc,lan9115" -- reg : Address and length of the io space for SMSC LAN -- interrupts : one or two interrupt specifiers - - The first interrupt is the SMSC LAN interrupt line - - The second interrupt (if present) is the PME (power - management event) interrupt that is able to wake up the host - system with a 50ms pulse on network activity -- phy-mode : See ethernet.txt file in the same directory - -Optional properties: -- reg-shift : Specify the quantity to shift the register offsets by -- reg-io-width : Specify the size (in bytes) of the IO accesses that - should be performed on the device. Valid value for SMSC LAN is - 2 or 4. If it's omitted or invalid, the size would be 2. -- smsc,irq-active-high : Indicates the IRQ polarity is active-high -- smsc,irq-push-pull : Indicates the IRQ type is push-pull -- smsc,force-internal-phy : Forces SMSC LAN controller to use - internal PHY -- smsc,force-external-phy : Forces SMSC LAN controller to use - external PHY -- smsc,save-mac-address : Indicates that mac address needs to be saved - before resetting the controller -- reset-gpios : a GPIO line connected to the RESET (active low) signal - of the device. On many systems this is wired high so the device goes - out of reset at power-on, but if it is under program control, this - optional GPIO can wake up in response to it. -- vdd33a-supply, vddvario-supply : 3.3V analog and IO logic power supplies - -Examples: - -lan9220@f4000000 { - compatible = "smsc,lan9220", "smsc,lan9115"; - reg = <0xf4000000 0x2000000>; - phy-mode = "mii"; - interrupt-parent = <&gpio1>; - interrupts = <31>, <32>; - reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; - reg-io-width = <4>; - smsc,irq-push-pull; -}; diff --git a/Documentation/devicetree/bindings/net/snps,dwmac.yaml b/Documentation/devicetree/bindings/net/snps,dwmac.yaml index d7652596a09b..42689b7d03a2 100644 --- a/Documentation/devicetree/bindings/net/snps,dwmac.yaml +++ b/Documentation/devicetree/bindings/net/snps,dwmac.yaml @@ -28,6 +28,7 @@ select: - snps,dwmac-4.00 - snps,dwmac-4.10a - snps,dwmac-4.20a + - snps,dwmac-5.10a - snps,dwxgmac - snps,dwxgmac-2.10 @@ -82,6 +83,7 @@ properties: - snps,dwmac-4.00 - snps,dwmac-4.10a - snps,dwmac-4.20a + - snps,dwmac-5.10a - snps,dwxgmac - snps,dwxgmac-2.10 @@ -375,6 +377,7 @@ allOf: - snps,dwmac-4.00 - snps,dwmac-4.10a - snps,dwmac-4.20a + - snps,dwmac-5.10a - snps,dwxgmac - snps,dwxgmac-2.10 - st,spear600-gmac |