diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pci')
3 files changed, 55 insertions, 2 deletions
diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt index 3be80c68941a..83aeb1f5a645 100644 --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt @@ -4,8 +4,8 @@ This PCIe host controller is based on the Synopsis Designware PCIe IP and thus inherits all the common properties defined in designware-pcie.txt. Required properties: -- compatible: "fsl,imx6q-pcie" -- reg: base addresse and length of the pcie controller +- compatible: "fsl,imx6q-pcie", "fsl,imx6sx-pcie", "fsl,imx6qp-pcie" +- reg: base address and length of the PCIe controller - interrupts: A list of interrupt outputs of the controller. Must contain an entry for each entry in the interrupt-names property. - interrupt-names: Must include the following entries: @@ -19,6 +19,20 @@ Optional properties: - fsl,tx-deemph-gen2-6db: Gen2 (6db) De-emphasis value. Default: 20 - fsl,tx-swing-full: Gen2 TX SWING FULL value. Default: 127 - fsl,tx-swing-low: TX launch amplitude swing_low value. Default: 127 +- fsl,max-link-speed: Specify PCI gen for link capability. Must be '2' for + gen2, otherwise will default to gen1. Note that the IMX6 LVDS clock outputs + do not meet gen2 jitter requirements and thus for gen2 capability a gen2 + compliant clock generator should be used and configured. +- reset-gpio: Should specify the GPIO for controlling the PCI bus device reset + signal. It's not polarity aware and defaults to active-low reset sequence + (L=reset state, H=operation state). +- reset-gpio-active-high: If present then the reset sequence using the GPIO + specified in the "reset-gpio" property is reversed (H=reset state, + L=operation state). + +Additional required properties for imx6sx-pcie: +- clock names: Must include the following additional entries: + - "pcie_inbound_axi" Example: diff --git a/Documentation/devicetree/bindings/pci/pci-armada8k.txt b/Documentation/devicetree/bindings/pci/pci-armada8k.txt new file mode 100644 index 000000000000..598533a57d79 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-armada8k.txt @@ -0,0 +1,38 @@ +* Marvell Armada 7K/8K PCIe interface + +This PCIe host controller is based on the Synopsis Designware PCIe IP +and thus inherits all the common properties defined in designware-pcie.txt. + +Required properties: +- compatible: "marvell,armada8k-pcie" +- reg: must contain two register regions + - the control register region + - the config space region +- reg-names: + - "ctrl" for the control register region + - "config" for the config space region +- interrupts: Interrupt specifier for the PCIe controler +- clocks: reference to the PCIe controller clock + +Example: + + pcie@f2600000 { + compatible = "marvell,armada8k-pcie", "snps,dw-pcie"; + reg = <0 0xf2600000 0 0x10000>, <0 0xf6f00000 0 0x80000>; + reg-names = "ctrl", "config"; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + device_type = "pci"; + dma-coherent; + + bus-range = <0 0xff>; + ranges = <0x81000000 0 0xf9000000 0 0xf9000000 0 0x10000 /* downstream I/O */ + 0x82000000 0 0xf6000000 0 0xf6000000 0 0xf00000>; /* non-prefetchable memory */ + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + num-lanes = <1>; + clocks = <&cpm_syscon0 1 13>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/pci/pci-keystone.txt b/Documentation/devicetree/bindings/pci/pci-keystone.txt index 54eae2938174..d08a4d51108f 100644 --- a/Documentation/devicetree/bindings/pci/pci-keystone.txt +++ b/Documentation/devicetree/bindings/pci/pci-keystone.txt @@ -56,6 +56,7 @@ Optional properties:- phy-names: name of the Generic Keystine SerDes phy for PCI - If boot loader already does PCI link establishment, then phys and phy-names shouldn't be present. + interrupts: platform interrupt for error interrupts. Designware DT Properties not applicable for Keystone PCI |