diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pinctrl')
3 files changed, 185 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt new file mode 100644 index 000000000000..d6074321f730 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/oxnas,pinctrl.txt @@ -0,0 +1,57 @@ +* Oxford Semiconductor OXNAS SoC Family Pin Controller + +Please refer to pinctrl-bindings.txt, ../gpio/gpio.txt, and +../interrupt-controller/interrupts.txt for generic information regarding +pin controller, GPIO, and interrupt bindings. + +OXNAS 'pin configuration node' is a node of a group of pins which can be +used for a specific device or function. This node represents configurations of +pins, optional function, and optional mux related configuration. + +Required properties for pin controller node: + - compatible: "oxsemi,ox810se-pinctrl" + - oxsemi,sys-ctrl: a phandle to the system controller syscon node + +Required properties for pin configuration sub-nodes: + - pins: List of pins to which the configuration applies. + +Optional properties for pin configuration sub-nodes: +---------------------------------------------------- + - function: Mux function for the specified pins. + - bias-pull-up: Enable weak pull-up. + +Example: + +pinctrl: pinctrl { + compatible = "oxsemi,ox810se-pinctrl"; + + /* Regmap for sys registers */ + oxsemi,sys-ctrl = <&sys>; + + pinctrl_uart2: pinctrl_uart2 { + uart2a { + pins = "gpio31"; + function = "fct3"; + }; + uart2b { + pins = "gpio32"; + function = "fct3"; + }; + }; +}; + +uart2: serial@900000 { + compatible = "ns16550a"; + reg = <0x900000 0x100000>; + clocks = <&sysclk>; + interrupts = <29>; + reg-shift = <0>; + fifo-size = <16>; + reg-io-width = <1>; + current-speed = <115200>; + no-loopback-test; + status = "disabled"; + resets = <&reset 22>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt new file mode 100644 index 000000000000..ad4fce3552bb --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt @@ -0,0 +1,127 @@ +Pincontrol driver for MAX77620 Power management IC from Maxim Semiconductor. + +Device has 8 GPIO pins which can be configured as GPIO as well as the +special IO functions. + +Please refer file <devicetree/bindings/pinctrl/pinctrl-bindings.txt> +for details of the common pinctrl bindings used by client devices, +including the meaning of the phrase "pin configuration node". + +Optional Pinmux properties: +-------------------------- +Following properties are required if default setting of pins are required +at boot. +- pinctrl-names: A pinctrl state named per <pinctrl-binding.txt>. +- pinctrl[0...n]: Properties to contain the phandle for pinctrl states per + <pinctrl-binding.txt>. + +The pin configurations are defined as child of the pinctrl states node. Each +sub-node have following properties: + +Required properties: +------------------ +- pins: List of pins. Valid values of pins properties are: + gpio0, gpio1, gpio2, gpio3, gpio4, gpio5, gpio6, gpio7. + +Optional properties: +------------------- +Following are optional properties defined as pinmux DT binding document +<pinctrl-bindings.txt>. Absence of properties will leave the configuration +on default. + function, + drive-push-pull, + drive-open-drain, + bias-pull-up, + bias-pull-down. + +Valid values for function properties are: + gpio, lpm-control-in, fps-out, 32k-out, sd0-dvs-in, sd1-dvs-in, + reference-out + +Theres is also customised properties for the GPIO1, GPIO2 and GPIO3. These +customised properties are required to configure FPS configuration parameters +of these GPIOs. Please refer <devicetree/bindings/mfd/max77620.txt> for more +detail of Flexible Power Sequence (FPS). + +- maxim,active-fps-source: FPS source for the GPIOs to get + enabled/disabled when system is in + active state. Valid values are: + - MAX77620_FPS_SRC_0, + FPS source is FPS0. + - MAX77620_FPS_SRC_1, + FPS source is FPS1 + - MAX77620_FPS_SRC_2 and + FPS source is FPS2 + - MAX77620_FPS_SRC_NONE. + GPIO is not controlled + by FPS events and it gets + enabled/disabled by register + access. + Absence of this property will leave + the FPS configuration register for that + GPIO to default configuration. + +- maxim,active-fps-power-up-slot: Sequencing event slot number on which + the GPIO get enabled when + master FPS input event set to HIGH. + Valid values are 0 to 7. + This is applicable if FPS source is + selected as FPS0, FPS1 or FPS2. + +- maxim,active-fps-power-down-slot: Sequencing event slot number on which + the GPIO get disabled when master + FPS input event set to LOW. + Valid values are 0 to 7. + This is applicable if FPS source is + selected as FPS0, FPS1 or FPS2. + +- maxim,suspend-fps-source: This is same as property + "maxim,active-fps-source" but value + get configured when system enters in + to suspend state. + +- maxim,suspend-fps-power-up-slot: This is same as property + "maxim,active-fps-power-up-slot" but + this value get configured into FPS + configuration register when system + enters into suspend. + This is applicable if suspend state + FPS source is selected as FPS0, FPS1 or + +- maxim,suspend-fps-power-down-slot: This is same as property + "maxim,active-fps-power-down-slot" but + this value get configured into FPS + configuration register when system + enters into suspend. + This is applicable if suspend state + FPS source is selected as FPS0, FPS1 or + FPS2. + +Example: +-------- +#include <dt-bindings/mfd/max77620.h> +... +max77620@3c { + + pinctrl-names = "default"; + pinctrl-0 = <&spmic_default>; + + spmic_default: pinmux@0 { + pin_gpio0 { + pins = "gpio0"; + function = "gpio"; + }; + + pin_gpio1 { + pins = "gpio1"; + function = "fps-out"; + maxim,active-fps-source = <MAX77620_FPS_SRC_0>; + }; + + pin_gpio2 { + pins = "gpio2"; + function = "fps-out"; + maxim,active-fps-source = <MAX77620_FPS_SRC_1>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt index d74e631e10da..b484ba1af78c 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt @@ -9,6 +9,7 @@ of PMIC's from Qualcomm. Definition: Should contain one of: "qcom,pm8018-mpp", "qcom,pm8038-mpp", + "qcom,pm8058-mpp", "qcom,pm8821-mpp", "qcom,pm8841-mpp", "qcom,pm8916-mpp", |