diff options
Diffstat (limited to 'Documentation/devicetree/bindings/powerpc')
| -rw-r--r-- | Documentation/devicetree/bindings/powerpc/fsl/ssi.txt | 73 |
1 files changed, 0 insertions, 73 deletions
diff --git a/Documentation/devicetree/bindings/powerpc/fsl/ssi.txt b/Documentation/devicetree/bindings/powerpc/fsl/ssi.txt deleted file mode 100644 index 5ff76c9c57d2..000000000000 --- a/Documentation/devicetree/bindings/powerpc/fsl/ssi.txt +++ /dev/null @@ -1,73 +0,0 @@ -Freescale Synchronous Serial Interface - -The SSI is a serial device that communicates with audio codecs. It can -be programmed in AC97, I2S, left-justified, or right-justified modes. - -Required properties: -- compatible: Compatible list, contains "fsl,ssi". -- cell-index: The SSI, <0> = SSI1, <1> = SSI2, and so on. -- reg: Offset and length of the register set for the device. -- interrupts: <a b> where a is the interrupt number and b is a - field that represents an encoding of the sense and - level information for the interrupt. This should be - encoded based on the information in section 2) - depending on the type of interrupt controller you - have. -- interrupt-parent: The phandle for the interrupt controller that - services interrupts for this device. -- fsl,mode: The operating mode for the SSI interface. - "i2s-slave" - I2S mode, SSI is clock slave - "i2s-master" - I2S mode, SSI is clock master - "lj-slave" - left-justified mode, SSI is clock slave - "lj-master" - l.j. mode, SSI is clock master - "rj-slave" - right-justified mode, SSI is clock slave - "rj-master" - r.j., SSI is clock master - "ac97-slave" - AC97 mode, SSI is clock slave - "ac97-master" - AC97 mode, SSI is clock master -- fsl,playback-dma: Phandle to a node for the DMA channel to use for - playback of audio. This is typically dictated by SOC - design. See the notes below. -- fsl,capture-dma: Phandle to a node for the DMA channel to use for - capture (recording) of audio. This is typically dictated - by SOC design. See the notes below. -- fsl,fifo-depth: The number of elements in the transmit and receive FIFOs. - This number is the maximum allowed value for SFCSR[TFWM0]. -- fsl,ssi-asynchronous: - If specified, the SSI is to be programmed in asynchronous - mode. In this mode, pins SRCK, STCK, SRFS, and STFS must - all be connected to valid signals. In synchronous mode, - SRCK and SRFS are ignored. Asynchronous mode allows - playback and capture to use different sample sizes and - sample rates. Some drivers may require that SRCK and STCK - be connected together, and SRFS and STFS be connected - together. This would still allow different sample sizes, - but not different sample rates. - -Optional properties: -- codec-handle: Phandle to a 'codec' node that defines an audio - codec connected to this SSI. This node is typically - a child of an I2C or other control node. - -Child 'codec' node required properties: -- compatible: Compatible list, contains the name of the codec - -Child 'codec' node optional properties: -- clock-frequency: The frequency of the input clock, which typically comes - from an on-board dedicated oscillator. - -Notes on fsl,playback-dma and fsl,capture-dma: - -On SOCs that have an SSI, specific DMA channels are hard-wired for playback -and capture. On the MPC8610, for example, SSI1 must use DMA channel 0 for -playback and DMA channel 1 for capture. SSI2 must use DMA channel 2 for -playback and DMA channel 3 for capture. The developer can choose which -DMA controller to use, but the channels themselves are hard-wired. The -purpose of these two properties is to represent this hardware design. - -The device tree nodes for the DMA channels that are referenced by -"fsl,playback-dma" and "fsl,capture-dma" must be marked as compatible with -"fsl,ssi-dma-channel". The SOC-specific compatible string (e.g. -"fsl,mpc8610-dma-channel") can remain. If these nodes are left as -"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel", then the generic Elo DMA -drivers (fsldma) will attempt to use them, and it will conflict with the -sound drivers. |