3 files changed, 44 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/rtc/dallas,ds1390.txt b/Documentation/devicetree/bindings/rtc/dallas,ds1390.txt
index 8e76f2648796..9882b819f173 100644
--- a/Documentation/devicetree/bindings/rtc/dallas,ds1390.txt
+++ b/Documentation/devicetree/bindings/rtc/dallas,ds1390.txt
@@ -11,7 +11,7 @@ Optional properties:
 - trickle-diode-disable : Do not use internal trickle charger diode
 	Should be given if internal trickle charger diode should be disabled
 Example:
-	ds1390: rtc@68 {
+	ds1390: rtc@0 {
 		compatible = "dallas,ds1390";
 		trickle-resistor-ohms = <250>;
 		reg = <0>;
diff --git a/Documentation/devicetree/bindings/rtc/epson,rx8900.txt b/Documentation/devicetree/bindings/rtc/epson,rx8900.txt
new file mode 100644
index 000000000000..3f61e516ecf6
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/epson,rx8900.txt
@@ -0,0 +1,22 @@
+Real Time Clock driver for:
+  - Epson RX8900
+  - Micro Crystal rv8803
+
+Required properties:
+- compatible: should be: "microcrystal,rv8803" or "epson,rx8900"
+- reg : the I2C address of the device for I2C
+
+Optional properties:
+- epson,vdet-disable : boolean, if present will disable voltage detector.
+  Should be set if no backup battery is used.
+- trickle-diode-disable : boolean, if present will disable internal trickle
+  charger diode
+
+Example:
+
+	rtc: rtc@32 {
+		compatible = "epson,rx8900"
+		reg = <0x32>;
+		epson,vdet-disable;
+		trickle-diode-disable;
+	};
diff --git a/Documentation/devicetree/bindings/rtc/rtc-omap.txt b/Documentation/devicetree/bindings/rtc/rtc-omap.txt
index bf7d11ae9bea..bee41f97044e 100644
--- a/Documentation/devicetree/bindings/rtc/rtc-omap.txt
+++ b/Documentation/devicetree/bindings/rtc/rtc-omap.txt
@@ -18,6 +18,18 @@ Optional properties:
   through pmic_power_en
 - clocks: Any internal or external clocks feeding in to rtc
 - clock-names: Corresponding names of the clocks
+- pinctrl-0: a phandle pointing to the pin settings for the device
+- pinctrl-names: should be "default"
+
+Optional subnodes:
+- generic pinctrl node
+
+Required pinctrl subnodes properties:
+- pins - Names of ext_wakeup pins to configure
+
+Optional pinctrl subnodes properties:
+- input-enable - Enables ext_wakeup
+- ti,active-high - Set input active high (by default active low)
 
 Example:
 
@@ -30,4 +42,13 @@ rtc@1c23000 {
 	system-power-controller;
 	clocks = <&clk_32k_rtc>, <&clk_32768_ck>;
 	clock-names = "ext-clk", "int-clk";
+
+	pinctrl-0 = <&ext_wakeup>;
+	pinctrl-names = "default";
+
+	ext_wakeup: ext-wakeup {
+		pins = "ext_wakeup0";
+		input-enable;
+		ti,active-high;
+	};
 };