diff options
Diffstat (limited to 'Documentation/devicetree/bindings/soc')
4 files changed, 276 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/soc/dove/pmu.txt b/Documentation/devicetree/bindings/soc/dove/pmu.txt new file mode 100644 index 000000000000..edd40b796b74 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/dove/pmu.txt @@ -0,0 +1,56 @@ +Device Tree bindings for Marvell PMU + +Required properties: + - compatible: value should be "marvell,dove-pmu". + May also include "simple-bus" if there are child devices, in which + case the ranges node is required. + - reg: two base addresses and sizes of the PM controller and PMU. + - interrupts: single interrupt number for the PMU interrupt + - interrupt-controller: must be specified as the PMU itself is an + interrupt controller. + - #interrupt-cells: must be 1. + - #reset-cells: must be 1. + - domains: sub-node containing domain descriptions + +Optional properties: + - ranges: defines the address mapping for child devices, as per the + standard property of this name. Required when compatible includes + "simple-bus". + +Power domain descriptions are listed as child nodes of the "domains" +sub-node. Each domain has the following properties: + +Required properties: + - #power-domain-cells: must be 0. + +Optional properties: + - marvell,pmu_pwr_mask: specifies the mask value for PMU power register + - marvell,pmu_iso_mask: specifies the mask value for PMU isolation register + - resets: points to the reset manager (PMU node) and reset index. + +Example: + + pmu: power-management@d0000 { + compatible = "marvell,dove-pmu"; + reg = <0xd0000 0x8000>, <0xd8000 0x8000>; + interrupts = <33>; + interrupt-controller; + #interrupt-cells = <1>; + #reset-cells = <1>; + + domains { + vpu_domain: vpu-domain { + #power-domain-cells = <0>; + marvell,pmu_pwr_mask = <0x00000008>; + marvell,pmu_iso_mask = <0x00000001>; + resets = <&pmu 16>; + }; + + gpu_domain: gpu-domain { + #power-domain-cells = <0>; + marvell,pmu_pwr_mask = <0x00000004>; + marvell,pmu_iso_mask = <0x00000002>; + resets = <&pmu 18>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt index a6c8afc8385a..e8f15e34027f 100644 --- a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt +++ b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt @@ -21,6 +21,18 @@ Required properties: These are the clocks which hardware needs to be enabled before enabling certain power domains. +Optional properties: +- vdec-supply: Power supply for the vdec power domain +- venc-supply: Power supply for the venc power domain +- isp-supply: Power supply for the isp power domain +- mm-supply: Power supply for the mm power domain +- venc_lt-supply: Power supply for the venc_lt power domain +- audio-supply: Power supply for the audio power domain +- usb-supply: Power supply for the usb power domain +- mfg_async-supply: Power supply for the mfg_async power domain +- mfg_2d-supply: Power supply for the mfg_2d power domain +- mfg-supply: Power supply for the mfg power domain + Example: scpsys: scpsys@10006000 { diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt new file mode 100644 index 000000000000..5cc82b8353d8 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt @@ -0,0 +1,104 @@ +Qualcomm Shared Memory Point 2 Point binding + +The Shared Memory Point to Point (SMP2P) protocol facilitates communication of +a single 32-bit value between two processors. Each value has a single writer +(the local side) and a single reader (the remote side). Values are uniquely +identified in the system by the directed edge (local processor ID to remote +processor ID) and a string identifier. + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,smp2p" + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: one entry specifying the smp2p notification interrupt + +- qcom,ipc: + Usage: required + Value type: <prop-encoded-array> + Definition: three entries specifying the outgoing ipc bit used for + signaling the remote end of the smp2p edge: + - phandle to a syscon node representing the apcs registers + - u32 representing offset to the register within the syscon + - u32 representing the ipc bit within the register + +- qcom,smem: + Usage: required + Value type: <u32 array> + Definition: two identifiers of the inbound and outbound smem items used + for this edge + +- qcom,local-pid: + Usage: required + Value type: <u32> + Definition: specifies the identfier of the local endpoint of this edge + +- qcom,remote-pid: + Usage: required + Value type: <u32> + Definition: specifies the identfier of the remote endpoint of this edge + += SUBNODES +Each SMP2P pair contain a set of inbound and outbound entries, these are +described in subnodes of the smp2p device node. The node names are not +important. + +- qcom,entry-name: + Usage: required + Value type: <string> + Definition: specifies the name of this entry, for inbound entries this + will be used to match against the remotely allocated entry + and for outbound entries this name is used for allocating + entries + +- interrupt-controller: + Usage: required for incoming entries + Value type: <empty> + Definition: marks the entry as inbound; the node should be specified + as a two cell interrupt-controller as defined in + "../interrupt-controller/interrupts.txt" + If not specified this node will denote the outgoing entry + +- #interrupt-cells: + Usage: required for incoming entries + Value type: <u32> + Definition: must be 2 - denoting the bit in the entry and IRQ flags + +- #qcom,state-cells: + Usage: required for outgoing entries + Value type: <u32> + Definition: must be 1 - denoting the bit in the entry + += EXAMPLE +The following example shows the SMP2P setup with the wireless processor, +defined from the 8974 apps processor's point-of-view. It encompasses one +inbound and one outbound entry: + +wcnss-smp2p { + compatible = "qcom,smp2p"; + qcom,smem = <431>, <451>; + + interrupts = <0 143 1>; + + qcom,ipc = <&apcs 8 18>; + + qcom,local-pid = <0>; + qcom,remote-pid = <4>; + + wcnss_smp2p_out: master-kernel { + qcom,entry-name = "master-kernel"; + + #qcom,state-cells = <1>; + }; + + wcnss_smp2p_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + + interrupt-controller; + #interrupt-cells = <2>; + }; +}; diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt new file mode 100644 index 000000000000..a6634c70850d --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt @@ -0,0 +1,104 @@ +Qualcomm Shared Memory State Machine + +The Shared Memory State Machine facilitates broadcasting of single bit state +information between the processors in a Qualcomm SoC. Each processor is +assigned 32 bits of state that can be modified. A processor can through a +matrix of bitmaps signal subscription of notifications upon changes to a +certain bit owned by a certain remote processor. + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,smsm" + +- qcom,ipc-N: + Usage: required + Value type: <prop-encoded-array> + Definition: three entries specifying the outgoing ipc bit used for + signaling the N:th remote processor + - phandle to a syscon node representing the apcs registers + - u32 representing offset to the register within the syscon + - u32 representing the ipc bit within the register + +- qcom,local-host: + Usage: optional + Value type: <u32> + Definition: identifier of the local processor in the list of hosts, or + in other words specifier of the column in the subscription + matrix representing the local processor + defaults to host 0 + +- #address-cells: + Usage: required + Value type: <u32> + Definition: must be 1 + +- #size-cells: + Usage: required + Value type: <u32> + Definition: must be 0 + += SUBNODES +Each processor's state bits are described by a subnode of the smsm device node. +Nodes can either be flagged as an interrupt-controller to denote a remote +processor's state bits or the local processors bits. The node names are not +important. + +- reg: + Usage: required + Value type: <u32> + Definition: specifies the offset, in words, of the first bit for this + entry + +- #qcom,state-cells: + Usage: required for local entry + Value type: <u32> + Definition: must be 1 - denotes bit number + +- interrupt-controller: + Usage: required for remote entries + Value type: <empty> + Definition: marks the entry as a interrupt-controller and the state bits + to belong to a remote processor + +- #interrupt-cells: + Usage: required for remote entries + Value type: <u32> + Definition: must be 2 - denotes bit number and IRQ flags + +- interrupts: + Usage: required for remote entries + Value type: <prop-encoded-array> + Definition: one entry specifying remote IRQ used by the remote processor + to signal changes of its state bits + + += EXAMPLE +The following example shows the SMEM setup for controlling properties of the +wireless processor, defined from the 8974 apps processor's point-of-view. It +encompasses one outbound entry and the outgoing interrupt for the wireless +processor. + +smsm { + compatible = "qcom,smsm"; + + #address-cells = <1>; + #size-cells = <0>; + + qcom,ipc-3 = <&apcs 8 19>; + + apps_smsm: apps@0 { + reg = <0>; + + #qcom,state-cells = <1>; + }; + + wcnss_smsm: wcnss@7 { + reg = <7>; + interrupts = <0 144 1>; + + interrupt-controller; + #interrupt-cells = <2>; + }; +}; |