diff options
Diffstat (limited to 'Documentation/devicetree/bindings/staging/imx-drm/ldb.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/staging/imx-drm/ldb.txt | 122 |
1 files changed, 0 insertions, 122 deletions
diff --git a/Documentation/devicetree/bindings/staging/imx-drm/ldb.txt b/Documentation/devicetree/bindings/staging/imx-drm/ldb.txt deleted file mode 100644 index 443bcb6134d5..000000000000 --- a/Documentation/devicetree/bindings/staging/imx-drm/ldb.txt +++ /dev/null @@ -1,122 +0,0 @@ -Device-Tree bindings for LVDS Display Bridge (ldb) - -LVDS Display Bridge -=================== - -The LVDS Display Bridge device tree node contains up to two lvds-channel -nodes describing each of the two LVDS encoder channels of the bridge. - -Required properties: - - #address-cells : should be <1> - - #size-cells : should be <0> - - compatible : should be "fsl,imx53-ldb" or "fsl,imx6q-ldb". - Both LDB versions are similar, but i.MX6 has an additional - multiplexer in the front to select any of the four IPU display - interfaces as input for each LVDS channel. - - gpr : should be <&gpr> on i.MX53 and i.MX6q. - The phandle points to the iomuxc-gpr region containing the LVDS - control register. -- clocks, clock-names : phandles to the LDB divider and selector clocks and to - the display interface selector clocks, as described in - Documentation/devicetree/bindings/clock/clock-bindings.txt - The following clocks are expected on i.MX53: - "di0_pll" - LDB LVDS channel 0 mux - "di1_pll" - LDB LVDS channel 1 mux - "di0" - LDB LVDS channel 0 gate - "di1" - LDB LVDS channel 1 gate - "di0_sel" - IPU1 DI0 mux - "di1_sel" - IPU1 DI1 mux - On i.MX6q the following additional clocks are needed: - "di2_sel" - IPU2 DI0 mux - "di3_sel" - IPU2 DI1 mux - The needed clock numbers for each are documented in - Documentation/devicetree/bindings/clock/imx5-clock.txt, and in - Documentation/devicetree/bindings/clock/imx6q-clock.txt. - -Optional properties: - - pinctrl-names : should be "default" on i.MX53, not used on i.MX6q - - pinctrl-0 : a phandle pointing to LVDS pin settings on i.MX53, - not used on i.MX6q - - fsl,dual-channel : boolean. if it exists, only LVDS channel 0 should - be configured - one input will be distributed on both outputs in dual - channel mode - -LVDS Channel -============ - -Each LVDS Channel has to contain a display-timings node that describes the -video timings for the connected LVDS display. For detailed information, also -have a look at Documentation/devicetree/bindings/video/display-timing.txt. - -Required properties: - - reg : should be <0> or <1> - - fsl,data-mapping : should be "spwg" or "jeida" - This describes how the color bits are laid out in the - serialized LVDS signal. - - fsl,data-width : should be <18> or <24> - - port: A port node with endpoint definitions as defined in - Documentation/devicetree/bindings/media/video-interfaces.txt. - On i.MX5, the internal two-input-multiplexer is used. - Due to hardware limitations, only one port (port@[0,1]) - can be used for each channel (lvds-channel@[0,1], respectively) - On i.MX6, there should be four ports (port@[0-3]) that correspond - to the four LVDS multiplexer inputs. - -example: - -gpr: iomuxc-gpr@53fa8000 { - /* ... */ -}; - -ldb: ldb@53fa8008 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,imx53-ldb"; - gpr = <&gpr>; - clocks = <&clks 122>, <&clks 120>, - <&clks 115>, <&clks 116>, - <&clks 123>, <&clks 85>; - clock-names = "di0_pll", "di1_pll", - "di0_sel", "di1_sel", - "di0", "di1"; - - lvds-channel@0 { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - fsl,data-mapping = "spwg"; - fsl,data-width = <24>; - - display-timings { - /* ... */ - }; - - port@0 { - reg = <0>; - - lvds0_in: endpoint { - remote-endpoint = <&ipu_di0_lvds0>; - }; - }; - }; - - lvds-channel@1 { - #address-cells = <1>; - #size-cells = <0>; - reg = <1>; - fsl,data-mapping = "spwg"; - fsl,data-width = <24>; - - display-timings { - /* ... */ - }; - - port@1 { - reg = <1>; - - lvds1_in: endpoint { - remote-endpoint = <&ipu_di1_lvds1>; - }; - }; - }; -}; |