diff options
Diffstat (limited to 'Documentation/devicetree/bindings/usb')
-rw-r--r-- | Documentation/devicetree/bindings/usb/amlogic,dwc3.txt | 88 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/usb/dwc2.txt | 7 |
2 files changed, 95 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/usb/amlogic,dwc3.txt b/Documentation/devicetree/bindings/usb/amlogic,dwc3.txt index 9a8b631904fd..b9f04e617eb7 100644 --- a/Documentation/devicetree/bindings/usb/amlogic,dwc3.txt +++ b/Documentation/devicetree/bindings/usb/amlogic,dwc3.txt @@ -40,3 +40,91 @@ Example device nodes: phy-names = "usb2-phy", "usb3-phy"; }; }; + +Amlogic Meson G12A DWC3 USB SoC Controller Glue + +The Amlogic G12A embeds a DWC3 USB IP Core configured for USB2 and USB3 +in host-only mode, and a DWC2 IP Core configured for USB2 peripheral mode +only. + +A glue connects the DWC3 core to USB2 PHYs and optionnaly to an USB3 PHY. + +One of the USB2 PHY can be re-routed in peripheral mode to a DWC2 USB IP. + +The DWC3 Glue controls the PHY routing and power, an interrupt line is +connected to the Glue to serve as OTG ID change detection. + +Required properties: +- compatible: Should be "amlogic,meson-g12a-usb-ctrl" +- clocks: a handle for the "USB" clock +- resets: a handle for the shared "USB" reset line +- reg: The base address and length of the registers +- interrupts: the interrupt specifier for the OTG detection +- phys: handle to used PHYs on the system + - a <0> phandle can be used if a PHY is not used +- phy-names: names of the used PHYs on the system : + - "usb2-phy0" for USB2 PHY0 if USBHOST_A port is used + - "usb2-phy1" for USB2 PHY1 if USBOTG_B port is used + - "usb3-phy0" for USB3 PHY if USB3_0 is used +- dr_mode: should be "host", "peripheral", or "otg" depending on + the usage and configuration of the OTG Capable port. + - "host" and "peripheral" means a fixed Host or Device only connection + - "otg" means the port can be used as both Host or Device and + be switched automatically using the OTG ID pin. + +Optional properties: +- vbus-supply: should be a phandle to the regulator controlling the VBUS + power supply when used in OTG switchable mode + +Required child nodes: + +A child node must exist to represent the core DWC3 IP block. The name of +the node is not important. The content of the node is defined in dwc3.txt. + +A child node must exist to represent the core DWC2 IP block. The name of +the node is not important. The content of the node is defined in dwc2.txt. + +PHY documentation is provided in the following places: +- Documentation/devicetree/bindings/phy/meson-g12a-usb2-phy.txt +- Documentation/devicetree/bindings/phy/meson-g12a-usb3-pcie-phy.txt + +Example device nodes: + usb: usb@ffe09000 { + compatible = "amlogic,meson-g12a-usb-ctrl"; + reg = <0x0 0xffe09000 0x0 0xa0>; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + clocks = <&clkc CLKID_USB>; + resets = <&reset RESET_USB>; + + dr_mode = "otg"; + + phys = <&usb2_phy0>, <&usb2_phy1>, + <&usb3_pcie_phy PHY_TYPE_USB3>; + phy-names = "usb2-phy0", "usb2-phy1", "usb3-phy0"; + + dwc2: usb@ff400000 { + compatible = "amlogic,meson-g12a-usb", "snps,dwc2"; + reg = <0x0 0xff400000 0x0 0x40000>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clkc CLKID_USB1_DDR_BRIDGE>; + clock-names = "ddr"; + phys = <&usb2_phy1>; + dr_mode = "peripheral"; + g-rx-fifo-size = <192>; + g-np-tx-fifo-size = <128>; + g-tx-fifo-size = <128 128 16 16 16>; + }; + + dwc3: usb@ff500000 { + compatible = "snps,dwc3"; + reg = <0x0 0xff500000 0x0 0x100000>; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + dr_mode = "host"; + snps,dis_u2_susphy_quirk; + snps,quirk-frame-length-adjustment; + }; + }; diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt index 6dc3c4a34483..49eac0dc86b0 100644 --- a/Documentation/devicetree/bindings/usb/dwc2.txt +++ b/Documentation/devicetree/bindings/usb/dwc2.txt @@ -14,6 +14,7 @@ Required properties: - "amlogic,meson8-usb": The DWC2 USB controller instance in Amlogic Meson8 SoCs; - "amlogic,meson8b-usb": The DWC2 USB controller instance in Amlogic Meson8b SoCs; - "amlogic,meson-gxbb-usb": The DWC2 USB controller instance in Amlogic S905 SoCs; + - "amlogic,meson-g12a-usb": The DWC2 USB controller instance in Amlogic G12A SoCs; - "amcc,dwc-otg": The DWC2 USB controller instance in AMCC Canyonlands 460EX SoCs; - snps,dwc2: A generic DWC2 USB controller with default parameters. - "st,stm32f4x9-fsotg": The DWC2 USB FS/HS controller instance in STM32F4x9 SoCs @@ -31,12 +32,18 @@ Refer to clk/clock-bindings.txt for generic clock consumer properties Optional properties: - phys: phy provider specifier - phy-names: shall be "usb2-phy" +- vbus-supply: reference to the VBUS regulator. Depending on the current mode + this is enabled (in "host" mode") or disabled (in "peripheral" mode). The + regulator is updated if the controller is configured in "otg" mode and the + status changes between "host" and "peripheral". Refer to phy/phy-bindings.txt for generic phy consumer properties - dr_mode: shall be one of "host", "peripheral" and "otg" Refer to usb/generic.txt - g-rx-fifo-size: size of rx fifo size in gadget mode. - g-np-tx-fifo-size: size of non-periodic tx fifo size in gadget mode. - g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) in gadget mode. +- snps,reset-phy-on-wake: If present indicates that we need to reset the PHY when + we detect a wakeup. This is due to a hardware errata. Deprecated properties: - g-use-dma: gadget DMA mode is automatically detected |