diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
101 files changed, 2343 insertions, 87 deletions
diff --git a/Documentation/devicetree/bindings/arm/gic.txt b/Documentation/devicetree/bindings/arm/gic.txt index 2da059a4790c..cc56021eb60b 100644 --- a/Documentation/devicetree/bindings/arm/gic.txt +++ b/Documentation/devicetree/bindings/arm/gic.txt @@ -11,13 +11,14 @@ have PPIs or SGIs. Main node required properties: - compatible : should be one of: - "arm,gic-400" + "arm,arm1176jzf-devchip-gic" + "arm,arm11mp-gic" "arm,cortex-a15-gic" - "arm,cortex-a9-gic" "arm,cortex-a7-gic" - "arm,arm11mp-gic" + "arm,cortex-a9-gic" + "arm,gic-400" + "arm,pl390" "brcm,brahma-b15-gic" - "arm,arm1176jzf-devchip-gic" "qcom,msm-8660-qgic" "qcom,msm-qgic2" - interrupt-controller : Identifies the node as an interrupt controller @@ -58,6 +59,21 @@ Optional regions, used when the GIC doesn't have banked registers. The offset is cpu-offset * cpu-nr. +- clocks : List of phandle and clock-specific pairs, one for each entry + in clock-names. +- clock-names : List of names for the GIC clock input(s). Valid clock names + depend on the GIC variant: + "ic_clk" (for "arm,arm11mp-gic") + "PERIPHCLKEN" (for "arm,cortex-a15-gic") + "PERIPHCLK", "PERIPHCLKEN" (for "arm,cortex-a9-gic") + "clk" (for "arm,gic-400") + "gclk" (for "arm,pl390") + +- power-domains : A phandle and PM domain specifier as defined by bindings of + the power controller specified by phandle, used when the GIC + is part of a Power or Clock Domain. + + Example: intc: interrupt-controller@fff11000 { diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt new file mode 100644 index 000000000000..b1f2ce17dff8 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt @@ -0,0 +1,22 @@ +Mediatek imgsys controller +============================ + +The Mediatek imgsys controller provides various clocks to the system. + +Required Properties: + +- compatible: Should be: + - "mediatek,mt8173-imgsys", "syscon" +- #clock-cells: Must be 1 + +The imgsys controller uses the common clk binding from +Documentation/devicetree/bindings/clock/clock-bindings.txt +The available clocks are defined in dt-bindings/clock/mt*-clk.h. + +Example: + +imgsys: clock-controller@15000000 { + compatible = "mediatek,mt8173-imgsys", "syscon"; + reg = <0 0x15000000 0 0x1000>; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt new file mode 100644 index 000000000000..4385946eadef --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt @@ -0,0 +1,22 @@ +Mediatek mmsys controller +============================ + +The Mediatek mmsys controller provides various clocks to the system. + +Required Properties: + +- compatible: Should be: + - "mediatek,mt8173-mmsys", "syscon" +- #clock-cells: Must be 1 + +The mmsys controller uses the common clk binding from +Documentation/devicetree/bindings/clock/clock-bindings.txt +The available clocks are defined in dt-bindings/clock/mt*-clk.h. + +Example: + +mmsys: clock-controller@14000000 { + compatible = "mediatek,mt8173-mmsys", "syscon"; + reg = <0 0x14000000 0 0x1000>; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt new file mode 100644 index 000000000000..1faacf1c1b25 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt @@ -0,0 +1,22 @@ +Mediatek vdecsys controller +============================ + +The Mediatek vdecsys controller provides various clocks to the system. + +Required Properties: + +- compatible: Should be: + - "mediatek,mt8173-vdecsys", "syscon" +- #clock-cells: Must be 1 + +The vdecsys controller uses the common clk binding from +Documentation/devicetree/bindings/clock/clock-bindings.txt +The available clocks are defined in dt-bindings/clock/mt*-clk.h. + +Example: + +vdecsys: clock-controller@16000000 { + compatible = "mediatek,mt8173-vdecsys", "syscon"; + reg = <0 0x16000000 0 0x1000>; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,vencltsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,vencltsys.txt new file mode 100644 index 000000000000..3cc299fd7857 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,vencltsys.txt @@ -0,0 +1,22 @@ +Mediatek vencltsys controller +============================ + +The Mediatek vencltsys controller provides various clocks to the system. + +Required Properties: + +- compatible: Should be: + - "mediatek,mt8173-vencltsys", "syscon" +- #clock-cells: Must be 1 + +The vencltsys controller uses the common clk binding from +Documentation/devicetree/bindings/clock/clock-bindings.txt +The available clocks are defined in dt-bindings/clock/mt*-clk.h. + +Example: + +vencltsys: clock-controller@19000000 { + compatible = "mediatek,mt8173-vencltsys", "syscon"; + reg = <0 0x19000000 0 0x1000>; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,vencsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,vencsys.txt new file mode 100644 index 000000000000..5bb2866a2b50 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,vencsys.txt @@ -0,0 +1,22 @@ +Mediatek vencsys controller +============================ + +The Mediatek vencsys controller provides various clocks to the system. + +Required Properties: + +- compatible: Should be: + - "mediatek,mt8173-vencsys", "syscon" +- #clock-cells: Must be 1 + +The vencsys controller uses the common clk binding from +Documentation/devicetree/bindings/clock/clock-bindings.txt +The available clocks are defined in dt-bindings/clock/mt*-clk.h. + +Example: + +vencsys: clock-controller@18000000 { + compatible = "mediatek,mt8173-vencsys", "syscon"; + reg = <0 0x18000000 0 0x1000>; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/arm/pmu.txt b/Documentation/devicetree/bindings/arm/pmu.txt index 435251fa9ce0..4b7c3d9b29bb 100644 --- a/Documentation/devicetree/bindings/arm/pmu.txt +++ b/Documentation/devicetree/bindings/arm/pmu.txt @@ -8,6 +8,8 @@ Required properties: - compatible : should be one of "arm,armv8-pmuv3" + "arm.cortex-a57-pmu" + "arm.cortex-a53-pmu" "arm,cortex-a17-pmu" "arm,cortex-a15-pmu" "arm,cortex-a12-pmu" diff --git a/Documentation/devicetree/bindings/arm/twd.txt b/Documentation/devicetree/bindings/arm/twd.txt index 75b8610939fa..383ea19c2bf0 100644 --- a/Documentation/devicetree/bindings/arm/twd.txt +++ b/Documentation/devicetree/bindings/arm/twd.txt @@ -19,6 +19,11 @@ interrupts. - reg : Specify the base address and the size of the TWD timer register window. +Optional + +- always-on : a boolean property. If present, the timer is powered through + an always-on power domain, therefore it never loses context. + Example: twd-timer@2c000600 { diff --git a/Documentation/devicetree/bindings/ata/ahci-fsl-qoriq.txt b/Documentation/devicetree/bindings/ata/ahci-fsl-qoriq.txt new file mode 100644 index 000000000000..032a7606b862 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/ahci-fsl-qoriq.txt @@ -0,0 +1,21 @@ +Binding for Freescale QorIQ AHCI SATA Controller + +Required properties: + - reg: Physical base address and size of the controller's register area. + - compatible: Compatibility string. Must be 'fsl,<chip>-ahci', where + chip could be ls1021a, ls2080a, ls1043a etc. + - clocks: Input clock specifier. Refer to common clock bindings. + - interrupts: Interrupt specifier. Refer to interrupt binding. + +Optional properties: + - dma-coherent: Enable AHCI coherent DMA operation. + - reg-names: register area names when there are more than 1 register area. + +Examples: + sata@3200000 { + compatible = "fsl,ls1021a-ahci"; + reg = <0x0 0x3200000 0x0 0x10000>; + interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&platform_clk 1>; + dma-coherent; + }; diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt index a2321819e7f5..c2340eeeb97f 100644 --- a/Documentation/devicetree/bindings/ata/ahci-platform.txt +++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt @@ -16,8 +16,6 @@ Required properties: - "snps,dwc-ahci" - "snps,exynos5440-ahci" - "snps,spear-ahci" - - "fsl,qoriq-ahci" : for qoriq series socs which include ls1021, ls2085, etc. - - "fsl,<chip>-ahci" : chip could be ls1021, ls2085 etc. - "generic-ahci" - interrupts : <interrupt mapping for SATA IRQ> - reg : <registers mapping> diff --git a/Documentation/devicetree/bindings/clock/at91-clock.txt b/Documentation/devicetree/bindings/clock/at91-clock.txt index 5ba6450693b9..181bc8ac4e3a 100644 --- a/Documentation/devicetree/bindings/clock/at91-clock.txt +++ b/Documentation/devicetree/bindings/clock/at91-clock.txt @@ -77,6 +77,9 @@ Required properties: "atmel,sama5d4-clk-h32mx": at91 h32mx clock + "atmel,sama5d2-clk-generated": + at91 generated clock + Required properties for SCKC node: - reg : defines the IO memory reserved for the SCKC. - #size-cells : shall be 0 (reg is used to encode clk id). @@ -461,3 +464,35 @@ For example: compatible = "atmel,sama5d4-clk-h32mx"; clocks = <&mck>; }; + +Required properties for generated clocks: +- #size-cells : shall be 0 (reg is used to encode clk id). +- #address-cells : shall be 1 (reg is used to encode clk id). +- clocks : shall be the generated clock source phandles. + e.g. clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>, <&audio_pll_pmc>; +- name: device tree node describing a specific generated clock. + * #clock-cells : from common clock binding; shall be set to 0. + * reg: peripheral id. See Atmel's datasheets to get a full + list of peripheral ids. + * atmel,clk-output-range : minimum and maximum clock frequency + (two u32 fields). + +For example: + gck { + compatible = "atmel,sama5d2-clk-generated"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>, <&audio_pll_pmc>; + + tcb0_gclk: tcb0_gclk { + #clock-cells = <0>; + reg = <35>; + atmel,clk-output-range = <0 83000000>; + }; + + pwm_gclk: pwm_gclk { + #clock-cells = <0>; + reg = <38>; + atmel,clk-output-range = <0 83000000>; + }; + }; diff --git a/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt b/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt new file mode 100644 index 000000000000..e56a1df3a9d3 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt @@ -0,0 +1,45 @@ +Broadcom BCM2835 CPRMAN clocks + +This binding uses the common clock binding: + Documentation/devicetree/bindings/clock/clock-bindings.txt + +The CPRMAN clock controller generates clocks in the audio power domain +of the BCM2835. There is a level of PLLs deriving from an external +oscillator, a level of PLL dividers that produce channels off of the +few PLLs, and a level of mostly-generic clock generators sourcing from +the PLL channels. Most other hardware components source from the +clock generators, but a few (like the ARM or HDMI) will source from +the PLL dividers directly. + +Required properties: +- compatible: Should be "brcm,bcm2835-cprman" +- #clock-cells: Should be <1>. The permitted clock-specifier values can be + found in include/dt-bindings/clock/bcm2835.h +- reg: Specifies base physical address and size of the registers +- clocks: The external oscillator clock phandle + +Example: + + clk_osc: clock@3 { + compatible = "fixed-clock"; + reg = <3>; + #clock-cells = <0>; + clock-output-names = "osc"; + clock-frequency = <19200000>; + }; + + clocks: cprman@7e101000 { + compatible = "brcm,bcm2835-cprman"; + #clock-cells = <1>; + reg = <0x7e101000 0x2000>; + clocks = <&clk_osc>; + }; + + i2c0: i2c@7e205000 { + compatible = "brcm,bcm2835-i2c"; + reg = <0x7e205000 0x1000>; + interrupts = <2 21>; + clocks = <&clocks BCM2835_CLOCK_VPU>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt b/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt index da8d9bb5751c..ede65a55e21b 100644 --- a/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt +++ b/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt @@ -130,3 +130,81 @@ These clock IDs are defined in: ch3_unused mipipll 4 BCM_CYGNUS_MIPIPLL_CH3_UNUSED ch4_unused mipipll 5 BCM_CYGNUS_MIPIPLL_CH4_UNUSED ch5_unused mipipll 6 BCM_CYGNUS_MIPIPLL_CH5_UNUSED + +Northstar and Northstar Plus +------ +PLL and leaf clock compatible strings for Northstar and Northstar Plus are: + "brcm,nsp-armpll" + "brcm,nsp-genpll" + "brcm,nsp-lcpll0" + +The following table defines the set of PLL/clock index and ID for Northstar and +Northstar Plus. These clock IDs are defined in: + "include/dt-bindings/clock/bcm-nsp.h" + + Clock Source Index ID + --- ----- ----- --------- + crystal N/A N/A N/A + + armpll crystal N/A N/A + + genpll crystal 0 BCM_NSP_GENPLL + phy genpll 1 BCM_NSP_GENPLL_PHY_CLK + ethernetclk genpll 2 BCM_NSP_GENPLL_ENET_SW_CLK + usbclk genpll 3 BCM_NSP_GENPLL_USB_PHY_REF_CLK + iprocfast genpll 4 BCM_NSP_GENPLL_IPROCFAST_CLK + sata1 genpll 5 BCM_NSP_GENPLL_SATA1_CLK + sata2 genpll 6 BCM_NSP_GENPLL_SATA2_CLK + + lcpll0 crystal 0 BCM_NSP_LCPLL0 + pcie_phy lcpll0 1 BCM_NSP_LCPLL0_PCIE_PHY_REF_CLK + sdio lcpll0 2 BCM_NSP_LCPLL0_SDIO_CLK + ddr_phy lcpll0 3 BCM_NSP_LCPLL0_DDR_PHY_CLK + +Northstar 2 +----------- +PLL and leaf clock compatible strings for Northstar 2 are: + "brcm,ns2-genpll-scr" + "brcm,ns2-genpll-sw" + "brcm,ns2-lcpll-ddr" + "brcm,ns2-lcpll-ports" + +The following table defines the set of PLL/clock index and ID for Northstar 2. +These clock IDs are defined in: + "include/dt-bindings/clock/bcm-ns2.h" + + Clock Source Index ID + --- ----- ----- --------- + crystal N/A N/A N/A + + genpll_scr crystal 0 BCM_NS2_GENPLL_SCR + scr genpll_scr 1 BCM_NS2_GENPLL_SCR_SCR_CLK + fs genpll_scr 2 BCM_NS2_GENPLL_SCR_FS_CLK + audio_ref genpll_scr 3 BCM_NS2_GENPLL_SCR_AUDIO_CLK + ch3_unused genpll_scr 4 BCM_NS2_GENPLL_SCR_CH3_UNUSED + ch4_unused genpll_scr 5 BCM_NS2_GENPLL_SCR_CH4_UNUSED + ch5_unused genpll_scr 6 BCM_NS2_GENPLL_SCR_CH5_UNUSED + + genpll_sw crystal 0 BCM_NS2_GENPLL_SW + rpe genpll_sw 1 BCM_NS2_GENPLL_SW_RPE_CLK + 250 genpll_sw 2 BCM_NS2_GENPLL_SW_250_CLK + nic genpll_sw 3 BCM_NS2_GENPLL_SW_NIC_CLK + chimp genpll_sw 4 BCM_NS2_GENPLL_SW_CHIMP_CLK + port genpll_sw 5 BCM_NS2_GENPLL_SW_PORT_CLK + sdio genpll_sw 6 BCM_NS2_GENPLL_SW_SDIO_CLK + + lcpll_ddr crystal 0 BCM_NS2_LCPLL_DDR + pcie_sata_usb lcpll_ddr 1 BCM_NS2_LCPLL_DDR_PCIE_SATA_USB_CLK + ddr lcpll_ddr 2 BCM_NS2_LCPLL_DDR_DDR_CLK + ch2_unused lcpll_ddr 3 BCM_NS2_LCPLL_DDR_CH2_UNUSED + ch3_unused lcpll_ddr 4 BCM_NS2_LCPLL_DDR_CH3_UNUSED + ch4_unused lcpll_ddr 5 BCM_NS2_LCPLL_DDR_CH4_UNUSED + ch5_unused lcpll_ddr 6 BCM_NS2_LCPLL_DDR_CH5_UNUSED + + lcpll_ports crystal 0 BCM_NS2_LCPLL_PORTS + wan lcpll_ports 1 BCM_NS2_LCPLL_PORTS_WAN_CLK + rgmii lcpll_ports 2 BCM_NS2_LCPLL_PORTS_RGMII_CLK + ch2_unused lcpll_ports 3 BCM_NS2_LCPLL_PORTS_CH2_UNUSED + ch3_unused lcpll_ports 4 BCM_NS2_LCPLL_PORTS_CH3_UNUSED + ch4_unused lcpll_ports 5 BCM_NS2_LCPLL_PORTS_CH4_UNUSED + ch5_unused lcpll_ports 6 BCM_NS2_LCPLL_PORTS_CH5_UNUSED diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-div6-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-div6-clocks.txt index 5ddb68418655..38dcf0370143 100644 --- a/Documentation/devicetree/bindings/clock/renesas,cpg-div6-clocks.txt +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-div6-clocks.txt @@ -1,7 +1,7 @@ * Renesas CPG DIV6 Clock The CPG DIV6 clocks are variable factor clocks provided by the Clock Pulse -Generator (CPG). They clock input is divided by a configurable factor from 1 +Generator (CPG). Their clock input is divided by a configurable factor from 1 to 64. Required Properties: diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt new file mode 100644 index 000000000000..59297d34b208 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt @@ -0,0 +1,69 @@ +* Renesas Clock Pulse Generator / Module Standby and Software Reset + +On Renesas ARM SoCs (SH/R-Mobile, R-Car, RZ), the CPG (Clock Pulse Generator) +and MSSR (Module Standby and Software Reset) blocks are intimately connected, +and share the same register block. + +They provide the following functionalities: + - The CPG block generates various core clocks, + - The MSSR block provides two functions: + 1. Module Standby, providing a Clock Domain to control the clock supply + to individual SoC devices, + 2. Reset Control, to perform a software reset of individual SoC devices. + +Required Properties: + - compatible: Must be one of: + - "renesas,r8a7795-cpg-mssr" for the r8a7795 SoC + + - reg: Base address and length of the memory resource used by the CPG/MSSR + block + + - clocks: References to external parent clocks, one entry for each entry in + clock-names + - clock-names: List of external parent clock names. Valid names are: + - "extal" (r8a7795) + - "extalr" (r8a7795) + + - #clock-cells: Must be 2 + - For CPG core clocks, the two clock specifier cells must be "CPG_CORE" + and a core clock reference, as defined in + <dt-bindings/clock/*-cpg-mssr.h>. + - For module clocks, the two clock specifier cells must be "CPG_MOD" and + a module number, as defined in the datasheet. + + - #power-domain-cells: Must be 0 + - SoC devices that are part of the CPG/MSSR Clock Domain and can be + power-managed through Module Standby should refer to the CPG device + node in their "power-domains" property, as documented by the generic PM + Domain bindings in + Documentation/devicetree/bindings/power/power_domain.txt. + + +Examples +-------- + + - CPG device node: + + cpg: clock-controller@e6150000 { + compatible = "renesas,r8a7795-cpg-mssr"; + reg = <0 0xe6150000 0 0x1000>; + clocks = <&extal_clk>, <&extalr_clk>; + clock-names = "extal", "extalr"; + #clock-cells = <2>; + #power-domain-cells = <0>; + }; + + + - CPG/MSSR Clock Domain member device node: + + scif2: serial@e6e88000 { + compatible = "renesas,scif-r8a7795", "renesas,scif"; + reg = <0 0xe6e88000 0 64>; + interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 310>; + clock-names = "sci_ick"; + dmas = <&dmac1 0x13>, <&dmac1 0x12>; + dma-names = "tx", "rx"; + power-domains = <&cpg>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/clock/silabs,si514.txt b/Documentation/devicetree/bindings/clock/silabs,si514.txt new file mode 100644 index 000000000000..ea1a9dbc63b6 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/silabs,si514.txt @@ -0,0 +1,24 @@ +Binding for Silicon Labs 514 programmable I2C clock generator. + +Reference +This binding uses the common clock binding[1]. Details about the device can be +found in the datasheet[2]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Si514 datasheet + http://www.silabs.com/Support%20Documents/TechnicalDocs/si514.pdf + +Required properties: + - compatible: Shall be "silabs,si514" + - reg: I2C device address. + - #clock-cells: From common clock bindings: Shall be 0. + +Optional properties: + - clock-output-names: From common clock bindings. Recommended to be "si514". + +Example: + si514: clock-generator@55 { + reg = <0x55>; + #clock-cells = <0>; + compatible = "silabs,si514"; + }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt index d8b168ebd5f1..844b3a0976bf 100644 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt @@ -23,6 +23,7 @@ Required properties: "st,stih407-plls-c32-a9", "st,clkgen-plls-c32" "sst,plls-c32-cx_0", "st,clkgen-plls-c32" "sst,plls-c32-cx_1", "st,clkgen-plls-c32" + "st,stih418-plls-c28-a9", "st,clkgen-plls-c32" "st,stih415-gpu-pll-c32", "st,clkgengpu-pll-c32" "st,stih416-gpu-pll-c32", "st,clkgengpu-pll-c32" diff --git a/Documentation/devicetree/bindings/edac/apm-xgene-edac.txt b/Documentation/devicetree/bindings/edac/apm-xgene-edac.txt index 78edb80002c8..78e2a31c58d0 100644 --- a/Documentation/devicetree/bindings/edac/apm-xgene-edac.txt +++ b/Documentation/devicetree/bindings/edac/apm-xgene-edac.txt @@ -5,6 +5,8 @@ The follow error types are supported: memory controller - Memory controller PMD (L1/L2) - Processor module unit (PMD) L1/L2 cache + L3 - L3 cache controller + SoC - SoC IP's such as Ethernet, SATA, and etc The following section describes the EDAC DT node binding. @@ -30,6 +32,17 @@ Required properties for PMD subnode: - reg : First resource shall be the PMD resource. - pmd-controller : Instance number of the PMD controller. +Required properties for L3 subnode: +- compatible : Shall be "apm,xgene-edac-l3" or + "apm,xgene-edac-l3-v2". +- reg : First resource shall be the L3 EDAC resource. + +Required properties for SoC subnode: +- compatible : Shall be "apm,xgene-edac-soc-v1" for revision 1 or + "apm,xgene-edac-l3-soc" for general value reporting + only. +- reg : First resource shall be the SoC EDAC resource. + Example: csw: csw@7e200000 { compatible = "apm,xgene-csw", "syscon"; @@ -76,4 +89,14 @@ Example: reg = <0x0 0x7c000000 0x0 0x200000>; pmd-controller = <0>; }; + + edacl3@7e600000 { + compatible = "apm,xgene-edac-l3"; + reg = <0x0 0x7e600000 0x0 0x1000>; + }; + + edacsoc@7e930000 { + compatible = "apm,xgene-edac-soc-v1"; + reg = <0x0 0x7e930000 0x0 0x1000>; + }; }; diff --git a/Documentation/devicetree/bindings/fpga/xilinx-zynq-fpga-mgr.txt b/Documentation/devicetree/bindings/fpga/xilinx-zynq-fpga-mgr.txt new file mode 100644 index 000000000000..7018aa896835 --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/xilinx-zynq-fpga-mgr.txt @@ -0,0 +1,19 @@ +Xilinx Zynq FPGA Manager + +Required properties: +- compatible: should contain "xlnx,zynq-devcfg-1.0" +- reg: base address and size for memory mapped io +- interrupts: interrupt for the FPGA manager device +- clocks: phandle for clocks required operation +- clock-names: name for the clock, should be "ref_clk" +- syscon: phandle for access to SLCR registers + +Example: + devcfg: devcfg@f8007000 { + compatible = "xlnx,zynq-devcfg-1.0"; + reg = <0xf8007000 0x100>; + interrupts = <0 8 4>; + clocks = <&clkc 12>; + clock-names = "ref_clk"; + syscon = <&slcr>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-msm.txt b/Documentation/devicetree/bindings/gpio/gpio-msm.txt deleted file mode 100644 index ac20e68a004e..000000000000 --- a/Documentation/devicetree/bindings/gpio/gpio-msm.txt +++ /dev/null @@ -1,26 +0,0 @@ -MSM GPIO controller bindings - -Required properties: -- compatible: - - "qcom,msm-gpio" for MSM controllers -- #gpio-cells : Should be two. - - first cell is the pin number - - second cell is used to specify optional parameters (unused) -- gpio-controller : Marks the device node as a GPIO controller. -- #interrupt-cells : Should be 2. -- interrupt-controller: Mark the device node as an interrupt controller -- interrupts : Specify the TLMM summary interrupt number -- ngpio : Specify the number of MSM GPIOs - -Example: - - msmgpio: gpio@fd510000 { - compatible = "qcom,msm-gpio"; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - reg = <0xfd510000 0x4000>; - interrupts = <0 208 0>; - ngpio = <150>; - }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt index b9a42f294dd0..13df9933f4cd 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt @@ -24,6 +24,7 @@ Required properties: ti,tca6408 ti,tca6416 ti,tca6424 + ti,tca9539 exar,xra1202 Example: diff --git a/Documentation/devicetree/bindings/gpio/gpio-zynq.txt b/Documentation/devicetree/bindings/gpio/gpio-zynq.txt index db4c6a663c03..7b542657f259 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-zynq.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-zynq.txt @@ -12,6 +12,13 @@ Required properties: - interrupts : Interrupt specifier (see interrupt bindings for details) - interrupt-parent : Must be core interrupt controller +- interrupt-controller : Marks the device node as an interrupt controller. +- #interrupt-cells : Should be 2. The first cell is the GPIO number. + The second cell bits[3:0] is used to specify trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. - reg : Address and length of the register set for the device Example: @@ -22,5 +29,7 @@ Example: gpio-controller; interrupt-parent = <&intc>; interrupts = <0 20 4>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0xe000a000 0x1000>; }; diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index 82d40e2505f6..069cdf6f9dac 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -54,9 +54,13 @@ only uses one. gpio-specifier may encode: bank, pin position inside the bank, whether pin is open-drain and whether pin is logically inverted. + Exact meaning of each specifier cell is controller specific, and must -be documented in the device tree binding for the device. Use the macros -defined in include/dt-bindings/gpio/gpio.h whenever possible: +be documented in the device tree binding for the device. + +Most controllers are however specifying a generic flag bitfield +in the last cell, so for these, use the macros defined in +include/dt-bindings/gpio/gpio.h whenever possible: Example of a node using GPIOs: @@ -67,6 +71,15 @@ Example of a node using GPIOs: GPIO_ACTIVE_HIGH is 0, so in this example gpio-specifier is "18 0" and encodes GPIO pin number, and GPIO flags as accepted by the "qe_pio_e" gpio-controller. +Optional standard bitfield specifiers for the last cell: + +- Bit 0: 0 means active high, 1 means active low +- Bit 1: 1 means single-ended wiring, see: + https://en.wikipedia.org/wiki/Single-ended_triode + When used with active-low, this means open drain/collector, see: + https://en.wikipedia.org/wiki/Open_collector + When used with active-high, this means open source/emitter + 1.1) GPIO specifier best practices ---------------------------------- @@ -118,6 +131,30 @@ Every GPIO controller node must contain both an empty "gpio-controller" property, and a #gpio-cells integer property, which indicates the number of cells in a gpio-specifier. +Optionally, a GPIO controller may have a "ngpios" property. This property +indicates the number of in-use slots of available slots for GPIOs. The +typical example is something like this: the hardware register is 32 bits +wide, but only 18 of the bits have a physical counterpart. The driver is +generally written so that all 32 bits can be used, but the IP block is reused +in a lot of designs, some using all 32 bits, some using 18 and some using +12. In this case, setting "ngpios = <18>;" informs the driver that only the +first 18 GPIOs, at local offset 0 .. 17, are in use. + +If these GPIOs do not happen to be the first N GPIOs at offset 0...N-1, an +additional bitmask is needed to specify which GPIOs are actually in use, +and which are dummies. The bindings for this case has not yet been +specified, but should be specified if/when such hardware appears. + +Example: + +gpio-controller@00000000 { + compatible = "foo"; + reg = <0x00000000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + ngpios = <18>; +} + The GPIO chip may contain GPIO hog definitions. GPIO hogging is a mechanism providing automatic GPIO request and configuration as part of the gpio-controller's driver probe function. diff --git a/Documentation/devicetree/bindings/gpio/netxbig-gpio-ext.txt b/Documentation/devicetree/bindings/gpio/netxbig-gpio-ext.txt new file mode 100644 index 000000000000..50ec2e690701 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/netxbig-gpio-ext.txt @@ -0,0 +1,22 @@ +Binding for the GPIO extension bus found on some LaCie/Seagate boards +(Example: 2Big/5Big Network v2, 2Big NAS). + +Required properties: +- compatible: "lacie,netxbig-gpio-ext". +- addr-gpios: GPIOs representing the address register (LSB -> MSB). +- data-gpios: GPIOs representing the data register (LSB -> MSB). +- enable-gpio: latches the new configuration (address, data) on raising edge. + +Example: + +netxbig_gpio_ext: netxbig-gpio-ext { + compatible = "lacie,netxbig-gpio-ext"; + + addr-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH + &gpio1 16 GPIO_ACTIVE_HIGH + &gpio1 17 GPIO_ACTIVE_HIGH>; + data-gpios = <&gpio1 12 GPIO_ACTIVE_HIGH + &gpio1 13 GPIO_ACTIVE_HIGH + &gpio1 14 GPIO_ACTIVE_HIGH>; + enable-gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index d77d412cbc68..c50cf13c852e 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -54,7 +54,6 @@ epson,rx8581 I2C-BUS INTERFACE REAL TIME CLOCK MODULE fsl,mag3110 MAG3110: Xtrinsic High Accuracy, 3D Magnetometer fsl,mc13892 MC13892: Power Management Integrated Circuit (PMIC) for i.MX35/51 fsl,mma8450 MMA8450Q: Xtrinsic Low-power, 3-axis Xtrinsic Accelerometer -fsl,mma8452 MMA8452Q: 3-axis 12-bit / 8-bit Digital Accelerometer fsl,mpr121 MPR121: Proximity Capacitive Touch Sensor Controller fsl,sgtl5000 SGTL5000: Ultra Low-Power Audio Codec gmt,g751 G751: Digital Temperature Sensor and Thermal Watchdog with Two-Wire Interface @@ -80,6 +79,7 @@ oki,ml86v7667 OKI ML86V7667 video decoder ovti,ov5642 OV5642: Color CMOS QSXGA (5-megapixel) Image Sensor with OmniBSI and Embedded TrueFocus pericom,pt7c4338 Real-time Clock Module plx,pex8648 48-Lane, 12-Port PCI Express Gen 2 (5.0 GT/s) Switch +pulsedlight,lidar-lite-v2 Pulsedlight LIDAR range-finding sensor ramtron,24c64 i2c serial eeprom (24cxx) ricoh,r2025sd I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC ricoh,r2221tl I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC @@ -88,6 +88,7 @@ ricoh,rs5c372b I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC ricoh,rv5c386 I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC ricoh,rv5c387a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC samsung,24ad0xd1 S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power) +sgx,vz89x SGX Sensortech VZ89X Sensors sii,s35390a 2-wire CMOS real-time clock skyworks,sky81452 Skyworks SKY81452: Six-Channel White LED Driver with Touch Panel Bias Supply st-micro,24c256 i2c serial eeprom (24cxx) diff --git a/Documentation/devicetree/bindings/iio/accel/mma8452.txt b/Documentation/devicetree/bindings/iio/accel/mma8452.txt new file mode 100644 index 000000000000..e3c37467d7da --- /dev/null +++ b/Documentation/devicetree/bindings/iio/accel/mma8452.txt @@ -0,0 +1,24 @@ +Freescale MMA8452Q, MMA8453Q, MMA8652FC or MMA8653FC triaxial accelerometer + +Required properties: + + - compatible: should contain one of + * "fsl,mma8452" + * "fsl,mma8453" + * "fsl,mma8652" + * "fsl,mma8653" + - reg: the I2C address of the chip + +Optional properties: + + - interrupt-parent: should be the phandle for the interrupt controller + - interrupts: interrupt mapping for GPIO IRQ + +Example: + + mma8453fc@1d { + compatible = "fsl,mma8453"; + reg = <0x1d>; + interrupt-parent = <&gpio1>; + interrupts = <5 0>; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/hi8435.txt b/Documentation/devicetree/bindings/iio/adc/hi8435.txt new file mode 100644 index 000000000000..3b0348c5e516 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/hi8435.txt @@ -0,0 +1,21 @@ +Holt Integrated Circuits HI-8435 threshold detector bindings + +Required properties: + - compatible: should be "holt,hi8435" + - reg: spi chip select number for the device + +Recommended properties: + - spi-max-frequency: definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Optional properties: + - gpios: GPIO used for controlling the reset pin + +Example: +sensor@0 { + compatible = "holt,hi8435"; + reg = <0>; + gpios = <&gpio6 1 0>; + + spi-max-frequency = <1000000>; +}; diff --git a/Documentation/devicetree/bindings/iio/light/apds9960.txt b/Documentation/devicetree/bindings/iio/light/apds9960.txt new file mode 100644 index 000000000000..174b709f16db --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/apds9960.txt @@ -0,0 +1,22 @@ +* Avago APDS9960 gesture/RGB/ALS/proximity sensor + +http://www.avagotech.com/docs/AV02-4191EN + +Required properties: + + - compatible: must be "avago,apds9960" + - reg: the I2c address of the sensor + - interrupt-parent: should be the phandle for the interrupt controller + - interrupts : the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic interrupt client + node bindings. + +Example: + +apds9960@39 { + compatible = "avago,apds9960"; + reg = <0x39>; + interrupt-parent = <&gpio1>; + interrupts = <16 1>; +}; diff --git a/Documentation/devicetree/bindings/iio/light/us5182d.txt b/Documentation/devicetree/bindings/iio/light/us5182d.txt new file mode 100644 index 000000000000..6f0a530144fd --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/us5182d.txt @@ -0,0 +1,34 @@ +* UPISEMI us5182d I2C ALS and Proximity sensor + +Required properties: +- compatible: must be "upisemi,usd5182" +- reg: the I2C address of the device + +Optional properties: +- upisemi,glass-coef: glass attenuation factor - compensation factor of + resolution 1000 for material transmittance. +- upisemi,dark-ths: array of 8 elements containing 16-bit thresholds (adc + counts) corresponding to every scale. +- upisemi,upper-dark-gain: 8-bit dark gain compensation factor(4 int and 4 + fractional bits - Q4.4) applied when light > threshold +- upisemi,lower-dark-gain: 8-bit dark gain compensation factor(4 int and 4 + fractional bits - Q4.4) applied when light < threshold + +If the optional properties are not specified these factors will default to the +values in the below example. +The glass-coef defaults to no compensation for the covering material. +The threshold array defaults to experimental values that work with US5182D +sensor on evaluation board - roughly between 12-32 lux. +There will be no dark-gain compensation by default when ALS > thresh +(0 * dark-gain), and a 1.35 compensation factor when ALS < thresh. + +Example: + + usd5182@39 { + compatible = "upisemi,usd5182"; + reg = <0x39>; + upisemi,glass-coef = < 1000 >; + upisemi,dark-ths = /bits/ 16 <170 200 512 512 800 2000 4000 8000>; + upisemi,upper-dark-gain = /bits/ 8 <0x00>; + upisemi,lower-dark-gain = /bits/ 8 <0x16>; + }; diff --git a/Documentation/devicetree/bindings/input/cypress,cyapa.txt b/Documentation/devicetree/bindings/input/cypress,cyapa.txt index 635a3b036630..8d91ba9ff2fd 100644 --- a/Documentation/devicetree/bindings/input/cypress,cyapa.txt +++ b/Documentation/devicetree/bindings/input/cypress,cyapa.txt @@ -25,7 +25,7 @@ Example: /* Cypress Gen3 touchpad */ touchpad@67 { compatible = "cypress,cyapa"; - reg = <0x24>; + reg = <0x67>; interrupt-parent = <&gpio>; interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO 2 */ wakeup-source; diff --git a/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-misc-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-misc-intc.txt index 391717a68f3b..ec96b1f01478 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-misc-intc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/qca,ath79-misc-intc.txt @@ -4,8 +4,8 @@ The MISC interrupt controller is a secondary controller for lower priority interrupt. Required Properties: -- compatible: has to be "qca,<soctype>-cpu-intc", "qca,ar7100-misc-intc" - as fallback +- compatible: has to be "qca,<soctype>-cpu-intc", "qca,ar7100-misc-intc" or + "qca,<soctype>-cpu-intc", "qca,ar7240-misc-intc" - reg: Base address and size of the controllers memory area - interrupt-parent: phandle of the parent interrupt controller. - interrupts: Interrupt specifier for the controllers interrupt. @@ -13,6 +13,9 @@ Required Properties: - #interrupt-cells : Specifies the number of cells needed to encode interrupt source, should be 1 +Compatible fallback depends on the SoC. Use ar7100 for ar71xx and ar913x, +use ar7240 for all other SoCs. + Please refer to interrupts.txt in this directory for details of the common Interrupt Controllers bindings used by client devices. @@ -28,3 +31,16 @@ Example: interrupt-controller; #interrupt-cells = <1>; }; + +Another example: + + interrupt-controller@18060010 { + compatible = "qca,ar9331-misc-intc", qca,ar7240-misc-intc"; + reg = <0x18060010 0x4>; + + interrupt-parent = <&cpuintc>; + interrupts = <6>; + + interrupt-controller; + #interrupt-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt index 63633bdea7e4..ae5054c27c99 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt @@ -10,6 +10,7 @@ Required properties: - "renesas,irqc-r8a7792" (R-Car V2H) - "renesas,irqc-r8a7793" (R-Car M2-N) - "renesas,irqc-r8a7794" (R-Car E2) + - "renesas,intc-ex-r8a7795" (R-Car H3) - #interrupt-cells: has to be <2>: an interrupt index and flags, as defined in interrupts.txt in this directory - clocks: Must contain a reference to the functional clock. diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt b/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt index 3443e0f838df..947863acc2d4 100644 --- a/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt +++ b/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt @@ -36,5 +36,24 @@ the PCIe specification. NOTE: this only applies to the SMMU itself, not masters connected upstream of the SMMU. +- msi-parent : See the generic MSI binding described in + devicetree/bindings/interrupt-controller/msi.txt + for a description of the msi-parent property. + - hisilicon,broken-prefetch-cmd : Avoid sending CMD_PREFETCH_* commands to the SMMU. + +** Example + + smmu@2b400000 { + compatible = "arm,smmu-v3"; + reg = <0x0 0x2b400000 0x0 0x20000>; + interrupts = <GIC_SPI 74 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 77 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 79 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "eventq", "priq", "cmdq-sync", "gerror"; + dma-coherent; + #iommu-cells = <0>; + msi-parent = <&its 0xff0000>; + }; diff --git a/Documentation/devicetree/bindings/iommu/ti,omap-iommu.txt b/Documentation/devicetree/bindings/iommu/ti,omap-iommu.txt index 869699925fd5..4bd10dd881b8 100644 --- a/Documentation/devicetree/bindings/iommu/ti,omap-iommu.txt +++ b/Documentation/devicetree/bindings/iommu/ti,omap-iommu.txt @@ -4,6 +4,7 @@ Required properties: - compatible : Should be one of, "ti,omap2-iommu" for OMAP2/OMAP3 IOMMU instances "ti,omap4-iommu" for OMAP4/OMAP5 IOMMU instances + "ti,dra7-dsp-iommu" for DRA7xx DSP IOMMU instances "ti,dra7-iommu" for DRA7xx IOMMU instances - ti,hwmods : Name of the hwmod associated with the IOMMU instance - reg : Address space for the configuration registers @@ -19,6 +20,13 @@ Optional properties: Should be either 8 or 32 (default: 32) - ti,iommu-bus-err-back : Indicates the IOMMU instance supports throwing back a bus error response on MMU faults. +- ti,syscon-mmuconfig : Should be a pair of the phandle to the DSP_SYSTEM + syscon node that contains the additional control + register for enabling the MMU, and the MMU instance + number (0-indexed) within the sub-system. This property + is required for DSP IOMMU instances on DRA7xx SoCs. The + instance number should be 0 for DSP MDMA MMUs and 1 for + DSP EDMA MMUs. Example: /* OMAP3 ISP MMU */ @@ -30,3 +38,22 @@ Example: ti,hwmods = "mmu_isp"; ti,#tlb-entries = <8>; }; + + /* DRA74x DSP2 MMUs */ + mmu0_dsp2: mmu@41501000 { + compatible = "ti,dra7-dsp-iommu"; + reg = <0x41501000 0x100>; + interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "mmu0_dsp2"; + #iommu-cells = <0>; + ti,syscon-mmuconfig = <&dsp2_system 0x0>; + }; + + mmu1_dsp2: mmu@41502000 { + compatible = "ti,dra7-dsp-iommu"; + reg = <0x41502000 0x100>; + interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "mmu1_dsp2"; + #iommu-cells = <0>; + ti,syscon-mmuconfig = <&dsp2_system 0x1>; + }; diff --git a/Documentation/devicetree/bindings/leds/leds-aat1290.txt b/Documentation/devicetree/bindings/leds/leds-aat1290.txt index c05ed91a4e42..85c0c58617f6 100644 --- a/Documentation/devicetree/bindings/leds/leds-aat1290.txt +++ b/Documentation/devicetree/bindings/leds/leds-aat1290.txt @@ -27,9 +27,9 @@ Required properties of the LED child node: - flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt Maximum flash LED supply current can be calculated using following formula: I = 1A * 162kohm / Rset. -- flash-timeout-us : see Documentation/devicetree/bindings/leds/common.txt - Maximum flash timeout can be calculated using following - formula: T = 8.82 * 10^9 * Ct. +- flash-max-timeout-us : see Documentation/devicetree/bindings/leds/common.txt + Maximum flash timeout can be calculated using following + formula: T = 8.82 * 10^9 * Ct. Optional properties of the LED child node: - label : see Documentation/devicetree/bindings/leds/common.txt @@ -54,7 +54,7 @@ aat1290 { label = "aat1290-flash"; led-max-microamp = <520833>; flash-max-microamp = <1012500>; - flash-timeout-us = <1940000>; + flash-max-timeout-us = <1940000>; }; }; diff --git a/Documentation/devicetree/bindings/leds/leds-bcm6328.txt b/Documentation/devicetree/bindings/leds/leds-bcm6328.txt index f9e36adc0ebf..3f48c1eaf085 100644 --- a/Documentation/devicetree/bindings/leds/leds-bcm6328.txt +++ b/Documentation/devicetree/bindings/leds/leds-bcm6328.txt @@ -29,6 +29,14 @@ Required properties: Optional properties: - brcm,serial-leds : Boolean, enables Serial LEDs. Default : false + - brcm,serial-mux : Boolean, enables Serial LEDs multiplexing. + Default : false + - brcm,serial-clk-low : Boolean, makes clock signal active low. + Default : false + - brcm,serial-dat-low : Boolean, makes data signal active low. + Default : false + - brcm,serial-shift-inv : Boolean, inverts Serial LEDs shift direction. + Default : false Each LED is represented as a sub-node of the brcm,bcm6328-leds device. @@ -110,6 +118,8 @@ Scenario 2 : BCM63268 with Serial/GPHY0 LEDs #size-cells = <0>; reg = <0x10001900 0x24>; brcm,serial-leds; + brcm,serial-dat-low; + brcm,serial-shift-inv; gphy0_spd0@0 { reg = <0>; diff --git a/Documentation/devicetree/bindings/leds/leds-netxbig.txt b/Documentation/devicetree/bindings/leds/leds-netxbig.txt new file mode 100644 index 000000000000..5ef92a26d768 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-netxbig.txt @@ -0,0 +1,92 @@ +Binding for the CPLD LEDs (GPIO extension bus) found on some LaCie/Seagate +boards (Example: 2Big/5Big Network v2, 2Big NAS). + +Required properties: +- compatible: "lacie,netxbig-leds". +- gpio-ext: Phandle for the gpio-ext bus. + +Optional properties: +- timers: Timer array. Each timer entry is represented by three integers: + Mode (gpio-ext bus), delay_on and delay_off. + +Each LED is represented as a sub-node of the netxbig-leds device. + +Required sub-node properties: +- mode-addr: Mode register address on gpio-ext bus. +- mode-val: Mode to value mapping. Each entry is represented by two integers: + A mode and the corresponding value on the gpio-ext bus. +- bright-addr: Brightness register address on gpio-ext bus. +- max-brightness: Maximum brightness value. + +Optional sub-node properties: +- label: Name for this LED. If omitted, the label is taken from the node name. +- linux,default-trigger: Trigger assigned to the LED. + +Example: + +netxbig-leds { + compatible = "lacie,netxbig-leds"; + + gpio-ext = &gpio_ext; + + timers = <NETXBIG_LED_TIMER1 500 500 + NETXBIG_LED_TIMER2 500 1000>; + + blue-power { + label = "netxbig:blue:power"; + mode-addr = <0>; + mode-val = <NETXBIG_LED_OFF 0 + NETXBIG_LED_ON 1 + NETXBIG_LED_TIMER1 3 + NETXBIG_LED_TIMER2 7>; + bright-addr = <1>; + max-brightness = <7>; + }; + red-power { + label = "netxbig:red:power"; + mode-addr = <0>; + mode-val = <NETXBIG_LED_OFF 0 + NETXBIG_LED_ON 2 + NETXBIG_LED_TIMER1 4>; + bright-addr = <1>; + max-brightness = <7>; + }; + blue-sata0 { + label = "netxbig:blue:sata0"; + mode-addr = <3>; + mode-val = <NETXBIG_LED_OFF 0 + NETXBIG_LED_ON 7 + NETXBIG_LED_SATA 1 + NETXBIG_LED_TIMER1 3>; + bright-addr = <2>; + max-brightness = <7>; + }; + red-sata0 { + label = "netxbig:red:sata0"; + mode-addr = <3>; + mode-val = <NETXBIG_LED_OFF 0 + NETXBIG_LED_ON 2 + NETXBIG_LED_TIMER1 4>; + bright-addr = <2>; + max-brightness = <7>; + }; + blue-sata1 { + label = "netxbig:blue:sata1"; + mode-addr = <4>; + mode-val = <NETXBIG_LED_OFF 0 + NETXBIG_LED_ON 7 + NETXBIG_LED_SATA 1 + NETXBIG_LED_TIMER1 3>; + bright-addr = <2>; + max-brightness = <7>; + }; + red-sata1 { + label = "netxbig:red:sata1"; + mode-addr = <4>; + mode-val = <NETXBIG_LED_OFF 0 + NETXBIG_LED_ON 2 + NETXBIG_LED_TIMER1 4>; + bright-addr = <2>; + max-brightness = <7>; + }; +}; diff --git a/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt b/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt index 4ef45636ebde..38941db23dd2 100644 --- a/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt +++ b/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt @@ -4,7 +4,8 @@ Required properties: - compatible : should be one of: "samsung,s5pv210-jpeg", "samsung,exynos4210-jpeg", - "samsung,exynos3250-jpeg", "samsung,exynos5420-jpeg"; + "samsung,exynos3250-jpeg", "samsung,exynos5420-jpeg", + "samsung,exynos5433-jpeg"; - reg : address and length of the JPEG codec IP register set; - interrupts : specifies the JPEG codec IP interrupt; - clock-names : should contain: diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt index 41811223e5be..a474359dd206 100644 --- a/Documentation/devicetree/bindings/mfd/axp20x.txt +++ b/Documentation/devicetree/bindings/mfd/axp20x.txt @@ -60,8 +60,8 @@ DCDC2 : DC-DC buck : vin2-supply DCDC3 : DC-DC buck : vin3-supply DCDC4 : DC-DC buck : vin4-supply DCDC5 : DC-DC buck : vin5-supply -DC1SW : On/Off Switch : dcdc1-supply : DCDC1 secondary output -DC5LDO : LDO : dcdc5-supply : input from DCDC5 +DC1SW : On/Off Switch : : DCDC1 secondary output +DC5LDO : LDO : : input from DCDC5 ALDO1 : LDO : aldoin-supply : shared supply ALDO2 : LDO : aldoin-supply : shared supply ALDO3 : LDO : aldoin-supply : shared supply diff --git a/Documentation/devicetree/bindings/misc/sram.txt b/Documentation/devicetree/bindings/misc/sram.txt index 36cbe5aea990..42ee9438b771 100644 --- a/Documentation/devicetree/bindings/misc/sram.txt +++ b/Documentation/devicetree/bindings/misc/sram.txt @@ -33,6 +33,12 @@ Optional properties in the area nodes: - compatible : standard definition, should contain a vendor specific string in the form <vendor>,[<device>-]<usage> +- pool : indicates that the particular reserved SRAM area is addressable + and in use by another device or devices +- export : indicates that the reserved SRAM area may be accessed outside + of the kernel, e.g. by bootloader or userspace +- label : the name for the reserved partition, if omitted, the label + is taken from the node name excluding the unit address. Example: @@ -48,4 +54,14 @@ sram: sram@5c000000 { compatible = "socvendor,smp-sram"; reg = <0x100 0x50>; }; + + device-sram@1000 { + reg = <0x1000 0x1000>; + pool; + }; + + exported@20000 { + reg = <0x20000 0x20000>; + export; + }; }; diff --git a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt index b7943f3f9995..dedfb02c744a 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt @@ -22,6 +22,8 @@ Optional properties: - voltage-ranges : two cells are required, first cell specifies minimum slot voltage (mV), second cell specifies maximum slot voltage (mV). Several ranges could be specified. + - little-endian : If the host controller is little-endian mode, specify + this property. The default endian mode is big-endian. Example: diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 0384fc3f64e8..f693baf87264 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -37,6 +37,7 @@ Optional properties: - sd-uhs-sdr104: SD UHS SDR104 speed is supported - sd-uhs-ddr50: SD UHS DDR50 speed is supported - cap-power-off-card: powering off the card is safe +- cap-mmc-hw-reset: eMMC hardware reset is supported - cap-sdio-irq: enable SDIO IRQ signalling on this interface - full-pwr-cycle: full power cycle of the card is supported - mmc-ddr-1_8v: eMMC high-speed DDR mode(1.8V I/O) is supported diff --git a/Documentation/devicetree/bindings/mmc/mtk-sd.txt b/Documentation/devicetree/bindings/mmc/mtk-sd.txt index a1adfa495ad3..0120c7f1109c 100644 --- a/Documentation/devicetree/bindings/mmc/mtk-sd.txt +++ b/Documentation/devicetree/bindings/mmc/mtk-sd.txt @@ -17,6 +17,11 @@ Required properties: - vmmc-supply: power to the Core - vqmmc-supply: power to the IO +Optional properties: +- assigned-clocks: PLL of the source clock +- assigned-clock-parents: parent of source clock, used for HS400 mode to get 400Mhz source clock +- hs400-ds-delay: HS400 DS delay setting + Examples: mmc0: mmc@11230000 { compatible = "mediatek,mt8173-mmc", "mediatek,mt8135-mmc"; @@ -24,9 +29,13 @@ mmc0: mmc@11230000 { interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_LOW>; vmmc-supply = <&mt6397_vemc_3v3_reg>; vqmmc-supply = <&mt6397_vio18_reg>; - clocks = <&pericfg CLK_PERI_MSDC30_0>, <&topckgen CLK_TOP_MSDC50_0_H_SEL>; + clocks = <&pericfg CLK_PERI_MSDC30_0>, + <&topckgen CLK_TOP_MSDC50_0_H_SEL>; clock-names = "source", "hclk"; pinctrl-names = "default", "state_uhs"; pinctrl-0 = <&mmc0_pins_default>; pinctrl-1 = <&mmc0_pins_uhs>; + assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>; + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_D2>; + hs400-ds-delay = <0x14015>; }; diff --git a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt index d38942f6c5ae..cae29eb5733d 100644 --- a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt +++ b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt @@ -6,11 +6,12 @@ and the properties used by the MMCIF device. Required properties: -- compatible: must contain one of the following +- compatible: should be "renesas,mmcif-<soctype>", "renesas,sh-mmcif" as a + fallback. Examples with <soctype> are: - "renesas,mmcif-r8a7740" for the MMCIF found in r8a7740 SoCs - "renesas,mmcif-r8a7790" for the MMCIF found in r8a7790 SoCs - "renesas,mmcif-r8a7791" for the MMCIF found in r8a7791 SoCs - - "renesas,sh-mmcif" for the generic MMCIF + - "renesas,mmcif-r8a7794" for the MMCIF found in r8a7794 SoCs - clocks: reference to the functional clock diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt index c327c2d6f23d..3dc13b68fc3f 100644 --- a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt @@ -14,6 +14,19 @@ Required Properties: before RK3288 - "rockchip,rk3288-dw-mshc": for Rockchip RK3288 +Optional Properties: +* clocks: from common clock binding: if ciu_drive and ciu_sample are + specified in clock-names, should contain handles to these clocks. + +* clock-names: Apart from the clock-names described in synopsys-dw-mshc.txt + two more clocks "ciu-drive" and "ciu-sample" are supported. They are used + to control the clock phases, "ciu-sample" is required for tuning high- + speed modes. + +* rockchip,default-sample-phase: The default phase to set ciu_sample at + probing, low speeds or in case where all phases work at tuning time. + If not specified 0 deg will be used. + Example: rkdwmmc0@12200000 { diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt index 346c6095a615..8636f5ae97e5 100644 --- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt @@ -75,6 +75,12 @@ Optional properties: * vmmc-supply: The phandle to the regulator to use for vmmc. If this is specified we'll defer probe until we can find this regulator. +* dmas: List of DMA specifiers with the controller specific format as described + in the generic DMA client binding. Refer to dma.txt for details. + +* dma-names: request names for generic DMA client binding. Must be "rx-tx". + Refer to dma.txt for details. + Aliases: - All the MSHC controller nodes should be represented in the aliases node using @@ -95,6 +101,23 @@ board specific portions as listed below. #size-cells = <0>; }; +[board specific internal DMA resources] + + dwmmc0@12200000 { + clock-frequency = <400000000>; + clock-freq-min-max = <400000 200000000>; + num-slots = <1>; + broken-cd; + fifo-depth = <0x80>; + card-detect-delay = <200>; + vmmc-supply = <&buck8>; + bus-width = <8>; + cap-mmc-highspeed; + cap-sd-highspeed; + }; + +[board specific generic DMA request binding] + dwmmc0@12200000 { clock-frequency = <400000000>; clock-freq-min-max = <400000 200000000>; @@ -106,4 +129,6 @@ board specific portions as listed below. bus-width = <8>; cap-mmc-highspeed; cap-sd-highspeed; + dmas = <&pdma 12>; + dma-names = "rx-tx"; }; diff --git a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt index f55aa280d34f..078060a97f95 100644 --- a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt +++ b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt @@ -37,6 +37,14 @@ Required properties for ethernet interfaces that have external PHY: Optional properties: - status: Should be "ok" or "disabled" for enabled/disabled. Default is "ok". +- tx-delay: Delay value for RGMII bridge TX clock. + Valid values are between 0 to 7, that maps to + 417, 717, 1020, 1321, 1611, 1913, 2215, 2514 ps + Default value is 4, which corresponds to 1611 ps +- rx-delay: Delay value for RGMII bridge RX clock. + Valid values are between 0 to 7, that maps to + 273, 589, 899, 1222, 1480, 1806, 2147, 2464 ps + Default value is 2, which corresponds to 899 ps Example: menetclk: menetclk { @@ -72,5 +80,7 @@ Example: /* Board-specific peripheral configurations */ &menet { + tx-delay = <4>; + rx-delay = <2>; status = "ok"; }; diff --git a/Documentation/devicetree/bindings/net/brcm,iproc-mdio.txt b/Documentation/devicetree/bindings/net/brcm,iproc-mdio.txt new file mode 100644 index 000000000000..8ba9ed11d716 --- /dev/null +++ b/Documentation/devicetree/bindings/net/brcm,iproc-mdio.txt @@ -0,0 +1,23 @@ +* Broadcom iProc MDIO bus controller + +Required properties: +- compatible: should be "brcm,iproc-mdio" +- reg: address and length of the register set for the MDIO interface +- #size-cells: must be 1 +- #address-cells: must be 0 + +Child nodes of this MDIO bus controller node are standard Ethernet PHY device +nodes as described in Documentation/devicetree/bindings/net/phy.txt + +Example: + +mdio@18002000 { + compatible = "brcm,iproc-mdio"; + reg = <0x18002000 0x8>; + #size-cells = <1>; + #address-cells = <0>; + + enet-gphy@0 { + reg = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/can/sun4i_can.txt b/Documentation/devicetree/bindings/net/can/sun4i_can.txt new file mode 100644 index 000000000000..84ed1909df76 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/sun4i_can.txt @@ -0,0 +1,36 @@ +Allwinner A10/A20 CAN controller Device Tree Bindings +----------------------------------------------------- + +Required properties: +- compatible: "allwinner,sun4i-a10-can" +- reg: physical base address and size of the Allwinner A10/A20 CAN register map. +- interrupts: interrupt specifier for the sole interrupt. +- clock: phandle and clock specifier. + +Example +------- + +SoC common .dtsi file: + + can0_pins_a: can0@0 { + allwinner,pins = "PH20","PH21"; + allwinner,function = "can"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; +... + can0: can@01c2bc00 { + compatible = "allwinner,sun4i-a10-can"; + reg = <0x01c2bc00 0x400>; + interrupts = <0 26 4>; + clocks = <&apb1_gates 4>; + status = "disabled"; + }; + +Board specific .dts file: + + can0: can@01c2bc00 { + pinctrl-names = "default"; + pinctrl-0 = <&can0_pins_a>; + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index a9df21aaa154..4efca560adda 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -30,6 +30,13 @@ Optional properties: - dual_emac : Specifies Switch to act as Dual EMAC - syscon : Phandle to the system control device node, which is the control module device of the am33x +- mode-gpios : Should be added if one/multiple gpio lines are + required to be driven so that cpsw data lines + can be connected to the phy via selective mux. + For example in dra72x-evm, pcf gpio has to be + driven low so that cpsw slave 0 and phy data + lines are connected via mux. + Slave Properties: Required properties: @@ -39,6 +46,7 @@ Required properties: Optional properties: - dual_emac_res_vlan : Specifies VID to be used to segregate the ports - mac-address : See ethernet.txt file in the same directory +- phy-handle : See ethernet.txt file in the same directory Note: "ti,hwmods" field is used to fetch the base address and irq resources from TI, omap hwmod data base during device registration. diff --git a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt index 1e97532a0b79..db74f0dc290c 100644 --- a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt +++ b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt @@ -57,6 +57,10 @@ Properties: "rgmii-id", as all other connection types are detected by hardware. - fsl,magic-packet : If present, indicates that the hardware supports waking up via magic packet. + - fsl,wake-on-filer : If present, indicates that the hardware supports + waking up by Filer General Purpose Interrupt (FGPI) asserted on the + Rx int line. This is an advanced power management capability allowing + certain packet types (user) defined by filer rules to wake up the system. - bd-stash : If present, indicates that the hardware supports stashing buffer descriptors in the L2. - rx-stash-len : Denotes the number of bytes of a received buffer to stash diff --git a/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt b/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt index 988fc694b663..d1df8a00e1f3 100644 --- a/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt +++ b/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt @@ -32,13 +32,13 @@ Required properties: Required properties: -- compatible: should be "hisilicon,hip04-mdio". +- compatible: should be "hisilicon,mdio". - Inherits from MDIO bus node binding [2] [2] Documentation/devicetree/bindings/net/phy.txt Example: mdio { - compatible = "hisilicon,hip04-mdio"; + compatible = "hisilicon,mdio"; reg = <0x28f1000 0x1000>; #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt b/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt new file mode 100644 index 000000000000..80411b2f0490 --- /dev/null +++ b/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt @@ -0,0 +1,49 @@ +Hisilicon DSA Fabric device controller + +Required properties: +- compatible: should be "hisilicon,hns-dsaf-v1" or "hisilicon,hns-dsaf-v2". + "hisilicon,hns-dsaf-v1" is for hip05. + "hisilicon,hns-dsaf-v2" is for Hi1610 and Hi1612. +- dsa-name: dsa fabric name who provide this interface. + should be "dsafX", X is the dsaf id. +- mode: dsa fabric mode string. only support one of dsaf modes like these: + "2port-64vf", + "6port-16rss", + "6port-16vf". +- interrupt-parent: the interrupt parent of this device. +- interrupts: should contain the DSA Fabric and rcb interrupt. +- reg: specifies base physical address(es) and size of the device registers. + The first region is external interface control register base and size. + The second region is SerDes base register and size. + The third region is the PPE register base and size. + The fourth region is dsa fabric base register and size. + The fifth region is cpld base register and size, it is not required if do not use cpld. +- phy-handle: phy handle of physicl port, 0 if not any phy device. see ethernet.txt [1]. +- buf-size: rx buffer size, should be 16-1024. +- desc-num: number of description in TX and RX queue, should be 512, 1024, 2048 or 4096. + +[1] Documentation/devicetree/bindings/net/phy.txt + +Example: + +dsa: dsa@c7000000 { + compatible = "hisilicon,hns-dsaf-v1"; + dsa_name = "dsaf0"; + mode = "6port-16rss"; + interrupt-parent = <&mbigen_dsa>; + reg = <0x0 0xC0000000 0x0 0x420000 + 0x0 0xC2000000 0x0 0x300000 + 0x0 0xc5000000 0x0 0x890000 + 0x0 0xc7000000 0x0 0x60000>; + phy-handle = <0 0 0 0 &soc0_phy4 &soc0_phy5 0 0>; + interrupts = <131 4>,<132 4>, <133 4>,<134 4>, + <135 4>,<136 4>, <137 4>,<138 4>, + <139 4>,<140 4>, <141 4>,<142 4>, + <143 4>,<144 4>, <145 4>,<146 4>, + <147 4>,<148 4>, <384 1>,<385 1>, + <386 1>,<387 1>, <388 1>,<389 1>, + <390 1>,<391 1>, + buf-size = <4096>; + desc-num = <1024>; + dma-coherent; +}; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hns-mdio.txt b/Documentation/devicetree/bindings/net/hisilicon-hns-mdio.txt new file mode 100644 index 000000000000..9c23fdf25018 --- /dev/null +++ b/Documentation/devicetree/bindings/net/hisilicon-hns-mdio.txt @@ -0,0 +1,22 @@ +Hisilicon MDIO bus controller + +Properties: +- compatible: "hisilicon,mdio","hisilicon,hns-mdio". +- reg: The base address of the MDIO bus controller register bank. +- #address-cells: Must be <1>. +- #size-cells: Must be <0>. MDIO addresses have no size component. + +Typically an MDIO bus might have several children. + +Example: + mdio@803c0000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "hisilicon,hns-mdio","hisilicon,mdio"; + reg = <0x0 0x803c0000 0x0 0x10000>; + + ethernet-phy@0 { + ... + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt b/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt new file mode 100644 index 000000000000..41d19be7011e --- /dev/null +++ b/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt @@ -0,0 +1,47 @@ +Hisilicon Network Subsystem NIC controller + +Required properties: +- compatible: "hisilicon,hns-nic-v1" or "hisilicon,hns-nic-v2". + "hisilicon,hns-nic-v1" is for hip05. + "hisilicon,hns-nic-v2" is for Hi1610 and Hi1612. +- ae-name: accelerator name who provides this interface, + is simply a name referring to the name of name in the accelerator node. +- port-id: is the index of port provided by DSAF (the accelerator). DSAF can + connect to 8 PHYs. Port 0 to 1 are both used for adminstration purpose. They + are called debug ports. + + The remaining 6 PHYs are taken according to the mode of DSAF. + + In NIC mode of DSAF, all 6 PHYs are taken as ethernet ports to the CPU. The + port-id can be 2 to 7. Here is the diagram: + +-----+---------------+ + | CPU | + +-+-+-+---+-+-+-+-+-+-+ + | | | | | | | | + debug service + port port + (0,1) (2-7) + + In Switch mode of DSAF, all 6 PHYs are taken as physical ports connect to a + LAN Switch while the CPU side assume itself have one single NIC connect to + this switch. In this case, the port-id will be 2 only. + +-----+---------------+ + | CPU | + +-+-+-+---+-+-+-+-+-+-+ + | | service| port(2) + debug +------------+ + port | switch | + (0,1) +-+-+-+-+-+-++ + | | | | | | + external port + +- local-mac-address: mac addr of the ethernet interface + +Example: + + ethernet@0{ + compatible = "hisilicon,hns-nic-v1"; + ae-name = "dsaf0"; + port-id = <0>; + local-mac-address = [a2 14 e4 4b 56 76]; + }; diff --git a/Documentation/devicetree/bindings/net/ieee802154/mrf24j40.txt b/Documentation/devicetree/bindings/net/ieee802154/mrf24j40.txt new file mode 100644 index 000000000000..a4ed2efb5b73 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ieee802154/mrf24j40.txt @@ -0,0 +1,20 @@ +* MRF24J40 IEEE 802.15.4 * + +Required properties: + - compatible: should be "microchip,mrf24j40", "microchip,mrf24j40ma", + or "microchip,mrf24j40mc" depends on your transceiver + board + - spi-max-frequency: maximal bus speed, should be set something under or equal + 10000000 + - reg: the chipselect index + - interrupts: the interrupt generated by the device. + +Example: + + mrf24j40ma@0 { + compatible = "microchip,mrf24j40ma"; + spi-max-frequency = <8500000>; + reg = <0>; + interrupts = <19 8>; + interrupt-parent = <&gpio3>; + }; diff --git a/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt b/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt index 7c4a0cc370cf..76df9173825a 100644 --- a/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt +++ b/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt @@ -1,7 +1,10 @@ * Marvell International Ltd. NCI NFC Controller Required properties: -- compatible: Should be "mrvl,nfc-uart". +- compatible: Should be: + - "marvell,nfc-uart" or "mrvl,nfc-uart" for UART devices + - "marvell,nfc-i2c" for I2C devices + - "marvell,nfc-spi" for SPI devices Optional SoC specific properties: - pinctrl-names: Contains only one value - "default". @@ -13,13 +16,19 @@ Optional UART-based chip specific properties: - flow-control: Specifies that the chip is using RTS/CTS. - break-control: Specifies that the chip needs specific break management. +Optional I2C-based chip specific properties: +- i2c-int-falling: Specifies that the chip read event shall be trigged on + falling edge. +- i2c-int-rising: Specifies that the chip read event shall be trigged on + rising edge. + Example (for ARM-based BeagleBoard Black with 88W8887 on UART5): &uart5 { status = "okay"; nfcmrvluart: nfcmrvluart@5 { - compatible = "mrvl,nfc-uart"; + compatible = "marvell,nfc-uart"; reset-n-io = <&gpio3 16 0>; @@ -27,3 +36,51 @@ Example (for ARM-based BeagleBoard Black with 88W8887 on UART5): flow-control; } }; + + +Example (for ARM-based BeagleBoard Black with 88W8887 on I2C1): + +&i2c1 { + status = "okay"; + clock-frequency = <400000>; + + nfcmrvli2c0: i2c@1 { + compatible = "marvell,nfc-i2c"; + + reg = <0x8>; + + /* I2C INT configuration */ + interrupt-parent = <&gpio3>; + interrupts = <21 0>; + + /* I2C INT trigger configuration */ + i2c-int-rising; + + /* Reset IO */ + reset-n-io = <&gpio3 19 0>; + }; +}; + + +Example (for ARM-based BeagleBoard Black on SPI0): + +&spi0 { + + mrvlnfcspi0: spi@0 { + compatible = "marvell,nfc-spi"; + + reg = <0>; + + /* SPI Bus configuration */ + spi-max-frequency = <3000000>; + spi-cpha; + spi-cpol; + + /* SPI INT configuration */ + interrupt-parent = <&gpio1>; + interrupts = <17 0>; + + /* Reset IO */ + reset-n-io = <&gpio3 19 0>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt b/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt index d707588ed734..263732e8879f 100644 --- a/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt +++ b/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt @@ -11,6 +11,10 @@ Required properties: Optional SoC Specific Properties: - pinctrl-names: Contains only one value - "default". - pintctrl-0: Specifies the pin control groups used for this controller. +- ese-present: Specifies that an ese is physically connected to the nfc +controller. +- uicc-present: Specifies that the uicc swp signal can be physically +connected to the nfc controller. Example (for ARM-based BeagleBoard xM with ST21NFCB on I2C2): @@ -29,5 +33,8 @@ Example (for ARM-based BeagleBoard xM with ST21NFCB on I2C2): interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; reset-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>; + + ese-present; + uicc-present; }; }; diff --git a/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt b/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt index 525681b6dc39..711ca85a363d 100644 --- a/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt +++ b/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt @@ -2,7 +2,7 @@ Required properties: - compatible: Should be "st,st21nfcb-spi" -- spi-max-frequency: Maximum SPI frequency (<= 10000000). +- spi-max-frequency: Maximum SPI frequency (<= 4000000). - interrupt-parent: phandle for the interrupt gpio controller - interrupts: GPIO interrupt to which the chip is connected - reset-gpios: Output GPIO pin used to reset the ST21NFCB @@ -10,6 +10,10 @@ Required properties: Optional SoC Specific Properties: - pinctrl-names: Contains only one value - "default". - pintctrl-0: Specifies the pin control groups used for this controller. +- ese-present: Specifies that an ese is physically connected to the nfc +controller. +- uicc-present: Specifies that the uicc swp signal can be physically +connected to the nfc controller. Example (for ARM-based BeagleBoard xM with ST21NFCB on SPI4): @@ -27,5 +31,8 @@ Example (for ARM-based BeagleBoard xM with ST21NFCB on SPI4): interrupts = <2 IRQ_TYPE_EDGE_RISING>; reset-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>; + + ese-present; + uicc-present; }; }; diff --git a/Documentation/devicetree/bindings/net/renesas,ravb.txt b/Documentation/devicetree/bindings/net/renesas,ravb.txt index 1fd8831437bf..b486f3f5f6a3 100644 --- a/Documentation/devicetree/bindings/net/renesas,ravb.txt +++ b/Documentation/devicetree/bindings/net/renesas,ravb.txt @@ -6,8 +6,12 @@ interface contains. Required properties: - compatible: "renesas,etheravb-r8a7790" if the device is a part of R8A7790 SoC. "renesas,etheravb-r8a7794" if the device is a part of R8A7794 SoC. + "renesas,etheravb-r8a7795" if the device is a part of R8A7795 SoC. - reg: offset and length of (1) the register block and (2) the stream buffer. -- interrupts: interrupt specifier for the sole interrupt. +- interrupts: A list of interrupt-specifiers, one for each entry in + interrupt-names. + If interrupt-names is not present, an interrupt specifier + for a single muxed interrupt. - phy-mode: see ethernet.txt file in the same directory. - phy-handle: see ethernet.txt file in the same directory. - #address-cells: number of address cells for the MDIO bus, must be equal to 1. @@ -18,6 +22,12 @@ Required properties: Optional properties: - interrupt-parent: the phandle for the interrupt controller that services interrupts for this device. +- interrupt-names: A list of interrupt names. + For the R8A7795 SoC this property is mandatory; + it should include one entry per channel, named "ch%u", + where %u is the channel number ranging from 0 to 24. + For other SoCs this property is optional; if present + it should contain "mux" for a single muxed interrupt. - pinctrl-names: pin configuration state name ("default"). - renesas,no-ether-link: boolean, specify when a board does not provide a proper AVB_LINK signal. @@ -27,13 +37,46 @@ Optional properties: Example: ethernet@e6800000 { - compatible = "renesas,etheravb-r8a7790"; - reg = <0 0xe6800000 0 0x800>, <0 0xee0e8000 0 0x4000>; + compatible = "renesas,etheravb-r8a7795"; + reg = <0 0xe6800000 0 0x800>, <0 0xe6a00000 0 0x10000>; interrupt-parent = <&gic>; - interrupts = <0 163 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp8_clks R8A7790_CLK_ETHERAVB>; - phy-mode = "rmii"; + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14", "ch15", + "ch16", "ch17", "ch18", "ch19", + "ch20", "ch21", "ch22", "ch23", + "ch24"; + clocks = <&mstp8_clks R8A7795_CLK_ETHERAVB>; + power-domains = <&cpg_clocks>; + phy-mode = "rgmii-id"; phy-handle = <&phy0>; + pinctrl-0 = <ðer_pins>; pinctrl-names = "default"; renesas,no-ether-link; @@ -41,8 +84,20 @@ Example: #size-cells = <0>; phy0: ethernet-phy@0 { + rxc-skew-ps = <900>; + rxdv-skew-ps = <0>; + rxd0-skew-ps = <0>; + rxd1-skew-ps = <0>; + rxd2-skew-ps = <0>; + rxd3-skew-ps = <0>; + txc-skew-ps = <900>; + txen-skew-ps = <0>; + txd0-skew-ps = <0>; + txd1-skew-ps = <0>; + txd2-skew-ps = <0>; + txd3-skew-ps = <0>; reg = <0>; interrupt-parent = <&gpio2>; - interrupts = <15 IRQ_TYPE_LEVEL_LOW>; + interrupts = <11 IRQ_TYPE_LEVEL_LOW>; }; }; diff --git a/Documentation/devicetree/bindings/net/smsc-lan87xx.txt b/Documentation/devicetree/bindings/net/smsc-lan87xx.txt new file mode 100644 index 000000000000..974edd5c85cc --- /dev/null +++ b/Documentation/devicetree/bindings/net/smsc-lan87xx.txt @@ -0,0 +1,24 @@ +SMSC LAN87xx Ethernet PHY + +Some boards require special tuning values. Configure them +through an Ethernet OF device node. + +Optional properties: + +- smsc,disable-energy-detect: + If set, do not enable energy detect mode for the SMSC phy. + default: enable energy detect mode + +Examples: +smsc phy with disabled energy detect mode on an am335x based board. +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; + status = "okay"; + + ethernetphy0: ethernet-phy@0 { + reg = <0>; + smsc,disable-energy-detect; + }; +}; diff --git a/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt b/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt new file mode 100644 index 000000000000..383d5889e95a --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt @@ -0,0 +1,20 @@ +Freescale i.MX6 On-Chip OTP Controller (OCOTP) device tree bindings + +This binding represents the on-chip eFuse OTP controller found on +i.MX6Q/D, i.MX6DL/S, i.MX6SL, and i.MX6SX SoCs. + +Required properties: +- compatible: should be one of + "fsl,imx6q-ocotp" (i.MX6Q/D/DL/S), + "fsl,imx6sl-ocotp" (i.MX6SL), or + "fsl,imx6sx-ocotp" (i.MX6SX), followed by "syscon". +- reg: Should contain the register base and length. +- clocks: Should contain a phandle pointing to the gated peripheral clock. + +Example: + + ocotp: ocotp@021bc000 { + compatible = "fsl,imx6q-ocotp", "syscon"; + reg = <0x021bc000 0x4000>; + clocks = <&clks IMX6QDL_CLK_IIM>; + }; diff --git a/Documentation/devicetree/bindings/nvmem/mxs-ocotp.txt b/Documentation/devicetree/bindings/nvmem/mxs-ocotp.txt new file mode 100644 index 000000000000..daebce9e6b07 --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/mxs-ocotp.txt @@ -0,0 +1,25 @@ +On-Chip OTP Memory for Freescale i.MX23/i.MX28 + +Required properties : +- compatible : + - "fsl,imx23-ocotp" for i.MX23 + - "fsl,imx28-ocotp" for i.MX28 +- #address-cells : Should be 1 +- #size-cells : Should be 1 +- reg : Address and length of OTP controller registers +- clocks : Should contain a reference to the hbus clock + += Data cells = +Are child nodes of mxs-ocotp, bindings of which as described in +bindings/nvmem/nvmem.txt + +Example for i.MX28: + + ocotp: ocotp@8002c000 { + compatible = "fsl,imx28-ocotp", "fsl,ocotp"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x8002c000 0x2000>; + clocks = <&clks 25>; + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt b/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt new file mode 100644 index 000000000000..8f86ab3b1046 --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt @@ -0,0 +1,38 @@ += Rockchip eFuse device tree bindings = + +Required properties: +- compatible: Should be "rockchip,rockchip-efuse" +- reg: Should contain the registers location and exact eFuse size +- clocks: Should be the clock id of eFuse +- clock-names: Should be "pclk_efuse" + += Data cells = +Are child nodes of eFuse, bindings of which as described in +bindings/nvmem/nvmem.txt + +Example: + + efuse: efuse@ffb40000 { + compatible = "rockchip,rockchip-efuse"; + reg = <0xffb40000 0x20>; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&cru PCLK_EFUSE256>; + clock-names = "pclk_efuse"; + + /* Data cells */ + cpu_leakage: cpu_leakage { + reg = <0x17 0x1>; + }; + }; + += Data consumers = +Are device nodes which consume nvmem data cells. + +Example: + + cpu_leakage { + ... + nvmem-cells = <&cpu_leakage>; + nvmem-cell-names = "cpu_leakage"; + }; diff --git a/Documentation/devicetree/bindings/nvmem/vf610-ocotp.txt b/Documentation/devicetree/bindings/nvmem/vf610-ocotp.txt new file mode 100644 index 000000000000..56ed481c3e26 --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/vf610-ocotp.txt @@ -0,0 +1,19 @@ +On-Chip OTP Memory for Freescale Vybrid + +Required Properties: + compatible: + - "fsl,vf610-ocotp" for VF5xx/VF6xx + #address-cells : Should be 1 + #size-cells : Should be 1 + reg : Address and length of OTP controller and fuse map registers + clocks : ipg clock we associate with the OCOTP peripheral + +Example for Vybrid VF5xx/VF6xx: + + ocotp: ocotp@400a5000 { + compatible = "fsl,vf610-ocotp"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x400a5000 0xCF0>; + clocks = <&clks VF610_CLK_OCOTP>; + }; diff --git a/Documentation/devicetree/bindings/pci/pci-msi.txt b/Documentation/devicetree/bindings/pci/pci-msi.txt new file mode 100644 index 000000000000..9b3cc817d181 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-msi.txt @@ -0,0 +1,220 @@ +This document describes the generic device tree binding for describing the +relationship between PCI devices and MSI controllers. + +Each PCI device under a root complex is uniquely identified by its Requester ID +(AKA RID). A Requester ID is a triplet of a Bus number, Device number, and +Function number. + +For the purpose of this document, when treated as a numeric value, a RID is +formatted such that: + +* Bits [15:8] are the Bus number. +* Bits [7:3] are the Device number. +* Bits [2:0] are the Function number. +* Any other bits required for padding must be zero. + +MSIs may be distinguished in part through the use of sideband data accompanying +writes. In the case of PCI devices, this sideband data may be derived from the +Requester ID. A mechanism is required to associate a device with both the MSI +controllers it can address, and the sideband data that will be associated with +its writes to those controllers. + +For generic MSI bindings, see +Documentation/devicetree/bindings/interrupt-controller/msi.txt. + + +PCI root complex +================ + +Optional properties +------------------- + +- msi-map: Maps a Requester ID to an MSI controller and associated + msi-specifier data. The property is an arbitrary number of tuples of + (rid-base,msi-controller,msi-base,length), where: + + * rid-base is a single cell describing the first RID matched by the entry. + + * msi-controller is a single phandle to an MSI controller + + * msi-base is an msi-specifier describing the msi-specifier produced for the + first RID matched by the entry. + + * length is a single cell describing how many consecutive RIDs are matched + following the rid-base. + + Any RID r in the interval [rid-base, rid-base + length) is associated with + the listed msi-controller, with the msi-specifier (r - rid-base + msi-base). + +- msi-map-mask: A mask to be applied to each Requester ID prior to being mapped + to an msi-specifier per the msi-map property. + +- msi-parent: Describes the MSI parent of the root complex itself. Where + the root complex and MSI controller do not pass sideband data with MSI + writes, this property may be used to describe the MSI controller(s) + used by PCI devices under the root complex, if defined as such in the + binding for the root complex. + + +Example (1) +=========== + +/ { + #address-cells = <1>; + #size-cells = <1>; + + msi: msi-controller@a { + reg = <0xa 0x1>; + compatible = "vendor,some-controller"; + msi-controller; + #msi-cells = <1>; + }; + + pci: pci@f { + reg = <0xf 0x1>; + compatible = "vendor,pcie-root-complex"; + device_type = "pci"; + + /* + * The sideband data provided to the MSI controller is + * the RID, identity-mapped. + */ + msi-map = <0x0 &msi_a 0x0 0x10000>, + }; +}; + + +Example (2) +=========== + +/ { + #address-cells = <1>; + #size-cells = <1>; + + msi: msi-controller@a { + reg = <0xa 0x1>; + compatible = "vendor,some-controller"; + msi-controller; + #msi-cells = <1>; + }; + + pci: pci@f { + reg = <0xf 0x1>; + compatible = "vendor,pcie-root-complex"; + device_type = "pci"; + + /* + * The sideband data provided to the MSI controller is + * the RID, masked to only the device and function bits. + */ + msi-map = <0x0 &msi_a 0x0 0x100>, + msi-map-mask = <0xff> + }; +}; + + +Example (3) +=========== + +/ { + #address-cells = <1>; + #size-cells = <1>; + + msi: msi-controller@a { + reg = <0xa 0x1>; + compatible = "vendor,some-controller"; + msi-controller; + #msi-cells = <1>; + }; + + pci: pci@f { + reg = <0xf 0x1>; + compatible = "vendor,pcie-root-complex"; + device_type = "pci"; + + /* + * The sideband data provided to the MSI controller is + * the RID, but the high bit of the bus number is + * ignored. + */ + msi-map = <0x0000 &msi 0x0000 0x8000>, + <0x8000 &msi 0x0000 0x8000>; + }; +}; + + +Example (4) +=========== + +/ { + #address-cells = <1>; + #size-cells = <1>; + + msi: msi-controller@a { + reg = <0xa 0x1>; + compatible = "vendor,some-controller"; + msi-controller; + #msi-cells = <1>; + }; + + pci: pci@f { + reg = <0xf 0x1>; + compatible = "vendor,pcie-root-complex"; + device_type = "pci"; + + /* + * The sideband data provided to the MSI controller is + * the RID, but the high bit of the bus number is + * negated. + */ + msi-map = <0x0000 &msi 0x8000 0x8000>, + <0x8000 &msi 0x0000 0x8000>; + }; +}; + + +Example (5) +=========== + +/ { + #address-cells = <1>; + #size-cells = <1>; + + msi_a: msi-controller@a { + reg = <0xa 0x1>; + compatible = "vendor,some-controller"; + msi-controller; + #msi-cells = <1>; + }; + + msi_b: msi-controller@b { + reg = <0xb 0x1>; + compatible = "vendor,some-controller"; + msi-controller; + #msi-cells = <1>; + }; + + msi_c: msi-controller@c { + reg = <0xc 0x1>; + compatible = "vendor,some-controller"; + msi-controller; + #msi-cells = <1>; + }; + + pci: pci@c { + reg = <0xf 0x1>; + compatible = "vendor,pcie-root-complex"; + device_type = "pci"; + + /* + * The sideband data provided to MSI controller a is the + * RID, but the high bit of the bus number is negated. + * The sideband data provided to MSI controller b is the + * RID, identity-mapped. + * MSI controller c is not addressable. + */ + msi-map = <0x0000 &msi_a 0x8000 0x08000>, + <0x8000 &msi_a 0x0000 0x08000>, + <0x0000 &msi_b 0x0000 0x10000>; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/brcm,cygnus-pcie-phy.txt b/Documentation/devicetree/bindings/phy/brcm,cygnus-pcie-phy.txt new file mode 100644 index 000000000000..761c4bc24a9b --- /dev/null +++ b/Documentation/devicetree/bindings/phy/brcm,cygnus-pcie-phy.txt @@ -0,0 +1,47 @@ +Broadcom Cygnus PCIe PHY + +Required properties: +- compatible: must be "brcm,cygnus-pcie-phy" +- reg: base address and length of the PCIe PHY block +- #address-cells: must be 1 +- #size-cells: must be 0 + +Each PCIe PHY should be represented by a child node + +Required properties For the child node: +- reg: the PHY ID +0 - PCIe RC 0 +1 - PCIe RC 1 +- #phy-cells: must be 0 + +Example: + pcie_phy: phy@0301d0a0 { + compatible = "brcm,cygnus-pcie-phy"; + reg = <0x0301d0a0 0x14>; + + pcie0_phy: phy@0 { + reg = <0>; + #phy-cells = <0>; + }; + + pcie1_phy: phy@1 { + reg = <1>; + #phy-cells = <0>; + }; + }; + + /* users of the PCIe phy */ + + pcie0: pcie@18012000 { + ... + ... + phys = <&pcie0_phy>; + phy-names = "pcie-phy"; + }; + + pcie1: pcie@18013000 { + ... + ... + phys = <pcie1_phy>; + phy-names = "pcie-phy"; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt new file mode 100644 index 000000000000..00100cf3e037 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt @@ -0,0 +1,68 @@ +mt65xx USB3.0 PHY binding +-------------------------- + +This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC. + +Required properties (controller (parent) node): + - compatible : should be "mediatek,mt8173-u3phy" + - reg : offset and length of register for phy, exclude port's + register. + - clocks : a list of phandle + clock-specifier pairs, one for each + entry in clock-names + - clock-names : must contain + "u3phya_ref": for reference clock of usb3.0 analog phy. + +Required nodes : a sub-node is required for each port the controller + provides. Address range information including the usual + 'reg' property is used inside these nodes to describe + the controller's topology. + +Required properties (port (child) node): +- reg : address and length of the register set for the port. +- #phy-cells : should be 1 (See second example) + cell after port phandle is phy type from: + - PHY_TYPE_USB2 + - PHY_TYPE_USB3 + +Example: + +u3phy: usb-phy@11290000 { + compatible = "mediatek,mt8173-u3phy"; + reg = <0 0x11290000 0 0x800>; + clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>; + clock-names = "u3phya_ref"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "okay"; + + phy_port0: port@11290800 { + reg = <0 0x11290800 0 0x800>; + #phy-cells = <1>; + status = "okay"; + }; + + phy_port1: port@11291000 { + reg = <0 0x11291000 0 0x800>; + #phy-cells = <1>; + status = "okay"; + }; +}; + +Specifying phy control of devices +--------------------------------- + +Device nodes should specify the configuration required in their "phys" +property, containing a phandle to the phy port node and a device type; +phy-names for each port are optional. + +Example: + +#include <dt-bindings/phy/phy.h> + +usb30: usb@11270000 { + ... + phys = <&phy_port0 PHY_TYPE_USB3>; + phy-names = "usb3-0"; + ... +}; diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt index 60c6f2a633e0..0289d3b07853 100644 --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt @@ -44,6 +44,9 @@ Required properties: - the "ref" clock is used to get the rate of the clock provided to the PHY module +Optional properties: +- vbus-supply: power-supply phandle for vbus power source + The first phandle argument in the PHY specifier identifies the PHY, its meaning is compatible dependent. For the currently supported SoCs (Exynos 4210 and Exynos 4212) it is as follows: diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt index 3c821cda1ad0..b321b26780dc 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -17,6 +17,7 @@ Required properties: "allwinner,sun8i-a23-pinctrl" "allwinner,sun8i-a23-r-pinctrl" "allwinner,sun8i-a33-pinctrl" + "allwinner,sun8i-a83t-pinctrl" - reg: Should contain the register physical address and length for the pin controller. diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pio4-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pio4-pinctrl.txt new file mode 100644 index 000000000000..61ac75706cc9 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pio4-pinctrl.txt @@ -0,0 +1,90 @@ +* Atmel PIO4 Controller + +The Atmel PIO4 controller is used to select the function of a pin and to +configure it. + +Required properties: +- compatible: "atmel,sama5d2-pinctrl". +- reg: base address and length of the PIO controller. +- interrupts: interrupt outputs from the controller, one for each bank. +- interrupt-controller: mark the device node as an interrupt controller. +- #interrupt-cells: should be two. +- gpio-controller: mark the device node as a gpio controller. +- #gpio-cells: should be two. + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices. + +Subnode format +Each node (or subnode) will list the pins it needs and how to configured these +pins. + + node { + pinmux = <PIN_NUMBER_PINMUX>; + GENERIC_PINCONFIG; + }; + +Required properties: +- pinmux: integer array. Each integer represents a pin number plus mux and +ioset settings. Use the macros from boot/dts/<soc>-pinfunc.h file to get the +right representation of the pin. + +Optional properties: +- GENERIC_PINCONFIG: generic pinconfig options to use, bias-disable, +bias-pull-down, bias-pull-up, drive-open-drain, input-schmitt-enable, +input-debounce, output-low, output-high. + +Example: + +#include <sama5d2-pinfunc.h> + +... +{ + pioA: pinctrl@fc038000 { + compatible = "atmel,sama5d2-pinctrl"; + reg = <0xfc038000 0x600>; + interrupts = <18 IRQ_TYPE_LEVEL_HIGH 7>, + <68 IRQ_TYPE_LEVEL_HIGH 7>, + <69 IRQ_TYPE_LEVEL_HIGH 7>, + <70 IRQ_TYPE_LEVEL_HIGH 7>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + clocks = <&pioA_clk>; + + pinctrl_i2c0_default: i2c0_default { + pinmux = <PIN_PD21__TWD0>, + <PIN_PD22__TWCK0>; + bias-disable; + }; + + pinctrl_led_gpio_default: led_gpio_default { + pinmux = <PIN_PB0>, + <PIN_PB5>; + bias-pull-up; + }; + + pinctrl_sdmmc1_default: sdmmc1_default { + cmd_data { + pinmux = <PIN_PA28__SDMMC1_CMD>, + <PIN_PA18__SDMMC1_DAT0>, + <PIN_PA19__SDMMC1_DAT1>, + <PIN_PA20__SDMMC1_DAT2>, + <PIN_PA21__SDMMC1_DAT3>; + bias-pull-up; + }; + + ck_cd { + pinmux = <PIN_PA22__SDMMC1_CK>, + <PIN_PA30__SDMMC1_CD>; + bias-disable; + }; + }; + ... + }; +}; +... diff --git a/Documentation/devicetree/bindings/pinctrl/berlin,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/berlin,pinctrl.txt index a8bb5e26019c..f8fa28ce163e 100644 --- a/Documentation/devicetree/bindings/pinctrl/berlin,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/berlin,pinctrl.txt @@ -20,7 +20,10 @@ Required properties: "marvell,berlin2cd-soc-pinctrl", "marvell,berlin2cd-system-pinctrl", "marvell,berlin2q-soc-pinctrl", - "marvell,berlin2q-system-pinctrl" + "marvell,berlin2q-system-pinctrl", + "marvell,berlin4ct-avio-pinctrl", + "marvell,berlin4ct-soc-pinctrl", + "marvell,berlin4ct-system-pinctrl" Required subnode-properties: - groups: a list of strings describing the group names. diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt b/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt index 6540ca56be5e..16589fb6f420 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt +++ b/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt @@ -3,8 +3,8 @@ Broadcom Cygnus GPIO/PINCONF Controller Required properties: - compatible: - Must be "brcm,cygnus-ccm-gpio", "brcm,cygnus-asiu-gpio", or - "brcm,cygnus-crmu-gpio" + Must be "brcm,cygnus-ccm-gpio", "brcm,cygnus-asiu-gpio", + "brcm,cygnus-crmu-gpio" or "brcm,iproc-gpio" - reg: Define the base and range of the I/O address space that contains the Cygnus @@ -26,9 +26,13 @@ Optional properties: - interrupt-controller: Specifies that the node is an interrupt controller -- pinmux: - Specifies the phandle to the IOMUX device, where pins can be individually -muxed to GPIO +- gpio-ranges: + Specifies the mapping between gpio controller and pin-controllers pins. + This requires 4 fields in cells defined as - + 1. Phandle of pin-controller. + 2. GPIO base pin offset. + 3 Pin-control base pin offset. + 4. number of gpio pins which are linearly mapped from pin base. Supported generic PINCONF properties in child nodes: @@ -78,6 +82,8 @@ Example: gpio-controller; interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>; interrupt-controller; + gpio-ranges = <&pinctrl 0 42 1>, + <&pinctrl 1 44 3>; }; /* diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt index 8bbf25d58656..457b2c68d47b 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt @@ -1,16 +1,42 @@ * Freescale i.MX7 Dual IOMUX Controller +iMX7D supports two iomuxc controllers, fsl,imx7d-iomuxc controller is similar +as previous iMX SoC generation and fsl,imx7d-iomuxc-lpsr which provides low +power state retention capabilities on gpios that are part of iomuxc-lpsr +(GPIO1_IO7..GPIO1_IO0). While iomuxc-lpsr provides its own set of registers for +mux and pad control settings, it shares the input select register from main +iomuxc controller for daisy chain settings, the fsl,input-sel property extends +fsl,imx-pinctrl driver to support iomuxc-lpsr controller. + +iomuxc_lpsr: iomuxc-lpsr@302c0000 { + compatible = "fsl,imx7d-iomuxc-lpsr"; + reg = <0x302c0000 0x10000>; + fsl,input-sel = <&iomuxc>; +}; + +iomuxc: iomuxc@30330000 { + compatible = "fsl,imx7d-iomuxc"; + reg = <0x30330000 0x10000>; +}; + +Pheriparials using pads from iomuxc-lpsr support low state retention power +state, under LPSR mode GPIO's state of pads are retain. + Please refer to fsl,imx-pinctrl.txt in this directory for common binding part and usage. Required properties: -- compatible: "fsl,imx7d-iomuxc" +- compatible: "fsl,imx7d-iomuxc" for main IOMUXC controller, or + "fsl,imx7d-iomuxc-lpsr" for Low Power State Retention IOMUXC controller. - fsl,pins: each entry consists of 6 integers and represents the mux and config setting for one pin. The first 5 integers <mux_reg conf_reg input_reg mux_val input_val> are specified using a PIN_FUNC_ID macro, which can be found in imx7d-pinfunc.h under device tree source folder. The last integer CONFIG is the pad setting value like pull-up on this pin. Please refer to i.MX7 Dual Reference Manual for detailed CONFIG settings. +- fsl,input-sel: required property for iomuxc-lpsr controller, this property is + a phandle for main iomuxc controller which shares the input select register for + daisy chain settings. CONFIG bits definition: PAD_CTL_PUS_100K_DOWN (0 << 5) @@ -25,3 +51,38 @@ PAD_CTL_DSE_X1 (0 << 0) PAD_CTL_DSE_X2 (1 << 0) PAD_CTL_DSE_X3 (2 << 0) PAD_CTL_DSE_X4 (3 << 0) + +Examples: +While iomuxc-lpsr is intended to be used by dedicated peripherals to take +advantages of LPSR power mode, is also possible that an IP to use pads from +any of the iomux controllers. For example the I2C1 IP can use SCL pad from +iomuxc-lpsr controller and SDA pad from iomuxc controller as: + +i2c1: i2c@30a20000 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1_1 &pinctrl_i2c1_2>; + status = "okay"; +}; + +iomuxc-lpsr@302c0000 { + compatible = "fsl,imx7d-iomuxc-lpsr"; + reg = <0x302c0000 0x10000>; + fsl,input-sel = <&iomuxc>; + + pinctrl_i2c1_1: i2c1grp-1 { + fsl,pins = < + MX7D_PAD_GPIO1_IO04__I2C1_SCL 0x4000007f + >; + }; +}; + +iomuxc@30330000 { + compatible = "fsl,imx7d-iomuxc"; + reg = <0x30330000 0x10000>; + + pinctrl_i2c1_2: i2c1grp-2 { + fsl,pins = < + MX7D_PAD_I2C1_SDA__I2C1_SDA 0x4000007f + >; + }; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt index 9496934528bd..ffadb7a371f6 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt @@ -19,6 +19,7 @@ Required Properties: - "renesas,pfc-r8a7791": for R8A7791 (R-Car M2-W) compatible pin-controller. - "renesas,pfc-r8a7793": for R8A7793 (R-Car M2-N) compatible pin-controller. - "renesas,pfc-r8a7794": for R8A7794 (R-Car E2) compatible pin-controller. + - "renesas,pfc-r8a7795": for R8A7795 (R-Car H3) compatible pin-controller. - "renesas,pfc-sh73a0": for SH73A0 (SH-Mobile AG5) compatible pin-controller. - reg: Base address and length of each memory resource used by the pin diff --git a/Documentation/devicetree/bindings/power/bq24257.txt b/Documentation/devicetree/bindings/power/bq24257.txt index 5c9d3940d07c..d693702c9c1e 100644 --- a/Documentation/devicetree/bindings/power/bq24257.txt +++ b/Documentation/devicetree/bindings/power/bq24257.txt @@ -1,21 +1,64 @@ -Binding for TI bq24257 Li-Ion Charger +Binding for TI bq24250/bq24251/bq24257 Li-Ion Charger Required properties: - compatible: Should contain one of the following: + * "ti,bq24250" + * "ti,bq24251" * "ti,bq24257" -- reg: integer, i2c address of the device. +- reg: integer, i2c address of the device. +- interrupt-parent: Should be the phandle for the interrupt controller. Use in + conjunction with "interrupts". +- interrupts: Interrupt mapping for GPIO IRQ (configure for both edges). Use in + conjunction with "interrupt-parent". - ti,battery-regulation-voltage: integer, maximum charging voltage in uV. -- ti,charge-current: integer, maximum charging current in uA. -- ti,termination-current: integer, charge will be terminated when current in - constant-voltage phase drops below this value (in uA). +- ti,charge-current: integer, maximum charging current in uA. +- ti,termination-current: integer, charge will be terminated when current in + constant-voltage phase drops below this value (in uA). + +Optional properties: +- pg-gpios: GPIO used for connecting the bq2425x device PG (Power Good) pin. + This pin is not available on all devices however it should be used if + possible as this is the recommended way to obtain the charger's input PG + state. If this pin is not specified a software-based approach for PG + detection is used. +- ti,current-limit: The maximum current to be drawn from the charger's input + (in uA). If this property is not specified, the input limit current is + set automatically using USB D+/D- signal based charger type detection. + If the hardware does not support the D+/D- based detection, a default + of 500,000 is used (=500mA) instead. +- ti,ovp-voltage: Configures the over voltage protection voltage (in uV). If + not specified a default of 6,5000,000 (=6.5V) is used. +- ti,in-dpm-voltage: Configures the threshold input voltage for the dynamic + power path management (in uV). If not specified a default of 4,360,000 + (=4.36V) is used. Example: bq24257 { compatible = "ti,bq24257"; reg = <0x6a>; + interrupt-parent = <&gpio1>; + interrupts = <16 IRQ_TYPE_EDGE_BOTH>; + + pg-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; ti,battery-regulation-voltage = <4200000>; ti,charge-current = <1000000>; ti,termination-current = <50000>; }; + +Example: + +bq24250 { + compatible = "ti,bq24250"; + reg = <0x6a>; + interrupt-parent = <&gpio1>; + interrupts = <16 IRQ_TYPE_EDGE_BOTH>; + + ti,battery-regulation-voltage = <4200000>; + ti,charge-current = <500000>; + ti,termination-current = <50000>; + ti,current-limit = <900000>; + ti,ovp-voltage = <9500000>; + ti,in-dpm-voltage = <4440000>; +}; diff --git a/Documentation/devicetree/bindings/power_supply/axp20x_usb_power.txt b/Documentation/devicetree/bindings/power_supply/axp20x_usb_power.txt new file mode 100644 index 000000000000..862f4a49dc49 --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/axp20x_usb_power.txt @@ -0,0 +1,34 @@ +AXP20x USB power supply + +Required Properties: +-compatible: "x-powers,axp202-usb-power-supply" + +This node is a subnode of the axp20x PMIC. + +Example: + +axp209: pmic@34 { + compatible = "x-powers,axp209"; + reg = <0x34>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + + regulators { + x-powers,dcdc-freq = <1500>; + + vdd_cpu: dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1450000>; + regulator-name = "vdd-cpu"; + }; + + ... + }; + + usb-power-supply: usb-power-supply { + compatible = "x-powers,axp202-usb-power-supply"; + }; +}; diff --git a/Documentation/devicetree/bindings/power_supply/qcom_smbb.txt b/Documentation/devicetree/bindings/power_supply/qcom_smbb.txt new file mode 100644 index 000000000000..65b88fac854b --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/qcom_smbb.txt @@ -0,0 +1,131 @@ +Qualcomm Switch-Mode Battery Charger and Boost + +PROPERTIES +- compatible: + Usage: required + Value type: <stringlist> + Description: Must be one of: + - "qcom,pm8941-charger" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Description: Base address of registers for SMBB block + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Description: The format of the specifier is defined by the binding document + describing the node's interrupt parent. Must contain one + specifier for each of the following interrupts, in order: + - charge done + - charge fast mode + - charge trickle mode + - battery temperature ok + - battery present + - charger disconnected + - USB-in valid + - DC-in valid + +- interrupt-names: + Usage: required + Value type: <stringlist> + Description: Must contain the following list, strictly ordered: + "chg-done", + "chg-fast", + "chg-trkl", + "bat-temp-ok", + "bat-present", + "chg-gone", + "usb-valid", + "dc-valid" + +- qcom,fast-charge-current-limit: + Usage: optional (default: 1A, or pre-configured value) + Value type: <u32>; uA; range [100mA : 3A] + Description: Maximum charge current; May be clamped to safety limits. + +- qcom,fast-charge-low-threshold-voltage: + Usage: optional (default: 3.2V, or pre-configured value) + Value type: <u32>; uV; range [2.1V : 3.6V] + Description: Battery voltage limit above which fast charging may operate; + Below this value linear or switch-mode auto-trickle-charging + will operate. + +- qcom,fast-charge-high-threshold-voltage: + Usage: optional (default: 4.2V, or pre-configured value) + Value type: <u32>; uV; range [3.24V : 5V] + Description: Battery voltage limit below which fast charging may operate; + The fast charger will attempt to charge the battery to this + voltage. May be clamped to safety limits. + +- qcom,fast-charge-safe-voltage: + Usage: optional (default: 4.2V, or pre-configured value) + Value type: <u32>; uV; range [3.24V : 5V] + Description: Maximum safe battery voltage; May be pre-set by bootloader, in + which case, setting this will harmlessly fail. The property + 'fast-charge-high-watermark' will be clamped by this value. + +- qcom,fast-charge-safe-current: + Usage: optional (default: 1A, or pre-configured value) + Value type: <u32>; uA; range [100mA : 3A] + Description: Maximum safe battery charge current; May pre-set by bootloader, + in which case, setting this will harmlessly fail. The property + 'qcom,fast-charge-current-limit' will be clamped by this value. + +- qcom,auto-recharge-threshold-voltage: + Usage: optional (default: 4.1V, or pre-configured value) + Value type: <u32>; uV; range [3.24V : 5V] + Description: Battery voltage limit below which auto-recharge functionality + will restart charging after end-of-charge; The high cutoff + limit for auto-recharge is 5% above this value. + +- qcom,minimum-input-voltage: + Usage: optional (default: 4.3V, or pre-configured value) + Value type: <u32>; uV; range [4.2V : 9.6V] + Description: Input voltage level above which charging may operate + +- qcom,dc-current-limit: + Usage: optional (default: 100mA, or pre-configured value) + Value type: <u32>; uA; range [100mA : 2.5A] + Description: Default DC charge current limit + +- qcom,disable-dc: + Usage: optional (default: false) + Value type: boolean: <u32> or <empty> + Description: Disable DC charger + +- qcom,jeita-extended-temp-range: + Usage: optional (default: false) + Value type: boolean: <u32> or <empty> + Description: Enable JEITA extended temperature range; This does *not* + adjust the maximum charge voltage or current in the extended + temperature range. It only allows charging when the battery + is in the extended temperature range. Voltage/current + regulation must be done externally to fully comply with + the JEITA safety guidelines if this flag is set. + +EXAMPLE +charger@1000 { + compatible = "qcom,pm8941-charger"; + reg = <0x1000 0x700>; + interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>, + <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>; + interrupt-names = "chg-done", + "chg-fast", + "chg-trkl", + "bat-temp-ok", + "bat-present", + "chg-gone", + "usb-valid", + "dc-valid"; + + qcom,fast-charge-current-limit = <1000000>; + qcom,dc-charge-current-limit = <1000000>; +}; diff --git a/Documentation/devicetree/bindings/power_supply/tps65217_charger.txt b/Documentation/devicetree/bindings/power_supply/tps65217_charger.txt new file mode 100644 index 000000000000..98d131acee95 --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/tps65217_charger.txt @@ -0,0 +1,12 @@ +TPS65217 Charger + +Required Properties: +-compatible: "ti,tps65217-charger" + +This node is a subnode of the tps65217 PMIC. + +Example: + + tps65217-charger { + compatible = "ti,tps65090-charger"; + }; diff --git a/Documentation/devicetree/bindings/regulator/act8865-regulator.txt b/Documentation/devicetree/bindings/regulator/act8865-regulator.txt index e91485d11241..6067d9830d07 100644 --- a/Documentation/devicetree/bindings/regulator/act8865-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/act8865-regulator.txt @@ -8,6 +8,8 @@ Required properties: Optional properties: - system-power-controller: Telling whether or not this pmic is controlling the system power. See Documentation/devicetree/bindings/power/power-controller.txt . +- active-semi,vsel-high: Indicates the VSEL pin is high. + If this property is missing, assume the VSEL pin is low(0). Optional input supply properties: - for act8600: @@ -49,6 +51,7 @@ Example: pmic: act8865@5b { compatible = "active-semi,act8865"; reg = <0x5b>; + active-semi,vsel-high; status = "disabled"; regulators { diff --git a/Documentation/devicetree/bindings/regulator/anatop-regulator.txt b/Documentation/devicetree/bindings/regulator/anatop-regulator.txt index 758eae24082a..37c4ea076f88 100644 --- a/Documentation/devicetree/bindings/regulator/anatop-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/anatop-regulator.txt @@ -13,6 +13,7 @@ Optional properties: - anatop-delay-reg-offset: Anatop MFD step time register offset - anatop-delay-bit-shift: Bit shift for the step time register - anatop-delay-bit-width: Number of bits used in the step time register +- vin-supply: The supply for this regulator Any property defined as part of the core regulator binding, defined in regulator.txt, can also be used. diff --git a/Documentation/devicetree/bindings/regulator/arizona-regulator.txt b/Documentation/devicetree/bindings/regulator/arizona-regulator.txt new file mode 100644 index 000000000000..443564d7784f --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/arizona-regulator.txt @@ -0,0 +1,17 @@ +Cirrus Logic Arizona class audio SoCs + +These devices are audio SoCs with extensive digital capabilities and a range +of analogue I/O. + +This document lists regulator specific bindings, see the primary binding +document: + ../mfd/arizona.txt + +Optional properties: + - wlf,ldoena : GPIO specifier for the GPIO controlling LDOENA + +Optional subnodes: + - ldo1 : Initial data for the LDO1 regulator, as covered in + Documentation/devicetree/bindings/regulator/regulator.txt + - micvdd : Initial data for the MICVDD regulator, as covered in + Documentation/devicetree/bindings/regulator/regulator.txt diff --git a/Documentation/devicetree/bindings/regulator/max77802.txt b/Documentation/devicetree/bindings/regulator/max77802.txt index 79e5476444f7..09d796ed48be 100644 --- a/Documentation/devicetree/bindings/regulator/max77802.txt +++ b/Documentation/devicetree/bindings/regulator/max77802.txt @@ -8,7 +8,28 @@ regulators that can be controlled over I2C. Following properties should be present in main device node of the MFD chip. -Optional node: +Optional properties: +- inb1-supply: The input supply for BUCK1 +- inb2-supply: The input supply for BUCK2 +- inb3-supply: The input supply for BUCK3 +- inb4-supply: The input supply for BUCK4 +- inb5-supply: The input supply for BUCK5 +- inb6-supply: The input supply for BUCK6 +- inb7-supply: The input supply for BUCK7 +- inb8-supply: The input supply for BUCK8 +- inb9-supply: The input supply for BUCK9 +- inb10-supply: The input supply for BUCK10 +- inl1-supply: The input supply for LDO8 and LDO15 +- inl2-supply: The input supply for LDO17, LDO27, LDO30 and LDO35 +- inl3-supply: The input supply for LDO3, LDO5, LDO6 and LDO7 +- inl4-supply: The input supply for LDO10, LDO11, LDO13 and LDO14 +- inl5-supply: The input supply for LDO9 and LDO19 +- inl6-supply: The input supply for LDO4, LDO21, LDO24 and LDO33 +- inl7-supply: The input supply for LDO18, LDO20, LDO28 and LDO29 +- inl9-supply: The input supply for LDO12, LDO23, LDO25, LDO26, LDO32 and LDO34 +- inl10-supply: The input supply for LDO1 and LDO2 + +Optional nodes: - regulators : The regulators of max77802 have to be instantiated under subnode named "regulators" using the following format. @@ -58,6 +79,8 @@ Example: #address-cells = <1>; #size-cells = <0>; + inb1-supply = <&parent_reg>; + regulators { ldo1_reg: LDO1 { regulator-name = "vdd_1v0"; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index 24bd422cecd5..1d112fc456aa 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -11,6 +11,7 @@ Optional properties: - regulator-always-on: boolean, regulator should never be disabled - regulator-boot-on: bootloader/firmware enabled regulator - regulator-allow-bypass: allow the regulator to go into bypass mode +- regulator-allow-set-load: allow the regulator performance level to be configured - <name>-supply: phandle to the parent supply/regulator node - regulator-ramp-delay: ramp delay for regulator(in uV/uS) For hardware which supports disabling ramp rate, it should be explicitly diff --git a/Documentation/devicetree/bindings/regulator/tps65023.txt b/Documentation/devicetree/bindings/regulator/tps65023.txt new file mode 100644 index 000000000000..a4714e4da370 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/tps65023.txt @@ -0,0 +1,60 @@ +TPS65023 family of regulators + +Required properties: +- compatible: Must be one of the following. + "ti,tps65020", + "ti,tps65021", + "ti,tps65023", +- reg: I2C slave address +- regulators: list of regulators provided by this controller, must be named + after their hardware counterparts: VDCDC[1-3] and LDO[1-2] +- regulators: This is the list of child nodes that specify the regulator + initialization data for defined regulators. The definition for each of + these nodes is defined using the standard binding for regulators found at + Documentation/devicetree/bindings/regulator/regulator.txt. + +Each regulator is defined using the standard binding for regulators. + +Example: + + tps65023@48 { + compatible = "ti,tps65023"; + reg = <0x48>; + + regulators { + VDCDC1 { + regulator-name = "vdd_mpu"; + regulator-always-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + VDCDC2 { + regulator-name = "vdd_core"; + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + VDCDC3 { + regulator-name = "vdd_io"; + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + LDO1 { + regulator-name = "vdd_usb18"; + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + LDO2 { + regulator-name = "vdd_usb33"; + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/rng/samsung,exynos-rng4.txt b/Documentation/devicetree/bindings/rng/samsung,exynos-rng4.txt new file mode 100644 index 000000000000..4ca8dd4d7e66 --- /dev/null +++ b/Documentation/devicetree/bindings/rng/samsung,exynos-rng4.txt @@ -0,0 +1,17 @@ +Exynos Pseudo Random Number Generator + +Required properties: + +- compatible : Should be "samsung,exynos4-rng". +- reg : Specifies base physical address and size of the registers map. +- clocks : Phandle to clock-controller plus clock-specifier pair. +- clock-names : "secss" as a clock name. + +Example: + + rng@10830400 { + compatible = "samsung,exynos4-rng"; + reg = <0x10830400 0x200>; + clocks = <&clock CLK_SSS>; + clock-names = "secss"; + }; diff --git a/Documentation/devicetree/bindings/rng/st,rng.txt b/Documentation/devicetree/bindings/rng/st,rng.txt new file mode 100644 index 000000000000..35734bc282e9 --- /dev/null +++ b/Documentation/devicetree/bindings/rng/st,rng.txt @@ -0,0 +1,15 @@ +STMicroelectronics HW Random Number Generator +---------------------------------------------- + +Required parameters: +compatible : Should be "st,rng" +reg : Base address and size of IP's register map. +clocks : Phandle to device's clock (See: ../clocks/clock-bindings.txt) + +Example: + +rng@fee80000 { + compatible = "st,rng"; + reg = <0xfee80000 0x1000>; + clocks = <&clk_sysin>; +} diff --git a/Documentation/devicetree/bindings/rng/st,stm32-rng.txt b/Documentation/devicetree/bindings/rng/st,stm32-rng.txt new file mode 100644 index 000000000000..47f04176f93b --- /dev/null +++ b/Documentation/devicetree/bindings/rng/st,stm32-rng.txt @@ -0,0 +1,21 @@ +STMicroelectronics STM32 HW RNG +=============================== + +The STM32 hardware random number generator is a simple fixed purpose IP and +is fully separated from other crypto functions. + +Required properties: + +- compatible : Should be "st,stm32-rng" +- reg : Should be register base and length as documented in the datasheet +- interrupts : The designated IRQ line for the RNG +- clocks : The clock needed to enable the RNG + +Example: + + rng: rng@50060800 { + compatible = "st,stm32-rng"; + reg = <0x50060800 0x400>; + interrupts = <80>; + clocks = <&rcc 0 38>; + }; diff --git a/Documentation/devicetree/bindings/serial/ingenic,uart.txt b/Documentation/devicetree/bindings/serial/ingenic,uart.txt index c2d3b3abe7d9..02cb7fe59cb7 100644 --- a/Documentation/devicetree/bindings/serial/ingenic,uart.txt +++ b/Documentation/devicetree/bindings/serial/ingenic,uart.txt @@ -1,7 +1,8 @@ * Ingenic SoC UART Required properties: -- compatible : "ingenic,jz4740-uart" or "ingenic,jz4780-uart" +- compatible : "ingenic,jz4740-uart", "ingenic,jz4760-uart", + "ingenic,jz4775-uart" or "ingenic,jz4780-uart" - reg : offset and length of the register set for the device. - interrupts : should contain uart interrupt. - clocks : phandles to the module & baud clocks. diff --git a/Documentation/devicetree/bindings/serial/pl011.txt b/Documentation/devicetree/bindings/serial/pl011.txt index cbae3d9a0278..77863aefe9ef 100644 --- a/Documentation/devicetree/bindings/serial/pl011.txt +++ b/Documentation/devicetree/bindings/serial/pl011.txt @@ -19,7 +19,7 @@ Optional properties: must correspond to the PCLK clocking the internal logic of the block. Just listing one clock (the first one) is deprecated. -- clocks-names: +- clock-names: When present, the first clock listed must be named "uartclk" and the second clock listed must be named "apb_pclk" diff --git a/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt index a2114c217376..182777fac9a2 100644 --- a/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt +++ b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt @@ -26,6 +26,12 @@ Required properties: Optional properties: - dmas: Should contain dma specifiers for transmit and receive channels - dma-names: Should contain "tx" for transmit and "rx" for receive channels +- qcom,tx-crci: Identificator <u32> for Client Rate Control Interface to be + used with TX DMA channel. Required when using DMA for transmission + with UARTDM v1.3 and bellow. +- qcom,rx-crci: Identificator <u32> for Client Rate Control Interface to be + used with RX DMA channel. Required when using DMA for reception + with UARTDM v1.3 and bellow. Note: Aliases may be defined to ensure the correct ordering of the UARTs. The alias serialN will result in the UART being assigned port N. If any diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index e84b13a8eda3..73f825e5e644 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -23,6 +23,8 @@ Required properties: - "renesas,scifa-r8a7794" for R8A7794 (R-Car E2) SCIFA compatible UART. - "renesas,scifb-r8a7794" for R8A7794 (R-Car E2) SCIFB compatible UART. - "renesas,hscif-r8a7794" for R8A7794 (R-Car E2) HSCIF compatible UART. + - "renesas,scif-r8a7795" for R8A7795 (R-Car H3) SCIF compatible UART. + - "renesas,hscif-r8a7795" for R8A7795 (R-Car H3) HSCIF compatible UART. - "renesas,scifa-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFA compatible UART. - "renesas,scifb-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFB compatible UART. - "renesas,scif" for generic SCIF compatible UART. diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt index 289c40ed7470..12bbe9f22560 100644 --- a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt +++ b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt @@ -15,6 +15,9 @@ The supplying peripheral clock can also be handled, needing a second property Required elements: "baudclk", "apb_pclk" Optional properties: +- snps,uart-16550-compatible : reflects the value of UART_16550_COMPATIBLE + configuration parameter. Define this if your UART does not implement the busy + functionality. - resets : phandle to the parent reset controller. - reg-shift : quantity to shift the register offsets by. If this property is not present then the register offsets are not shifted. diff --git a/Documentation/devicetree/bindings/spi/brcm,bcm2835-aux-spi.txt b/Documentation/devicetree/bindings/spi/brcm,bcm2835-aux-spi.txt new file mode 100644 index 000000000000..9887b0724759 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/brcm,bcm2835-aux-spi.txt @@ -0,0 +1,38 @@ +Broadcom BCM2835 auxiliar SPI1/2 controller + +The BCM2835 contains two forms of SPI master controller, one known simply as +SPI0, and the other known as the "Universal SPI Master"; part of the +auxiliary block. This binding applies to the SPI1/2 controller. + +Required properties: +- compatible: Should be "brcm,bcm2835-aux-spi". +- reg: Should contain register location and length for the spi block +- interrupts: Should contain shared interrupt of the aux block +- clocks: The clock feeding the SPI controller - needs to + point to the auxiliar clock driver of the bcm2835, + as this clock will enable the output gate for the specific + clock. +- cs-gpios: the cs-gpios (native cs is NOT supported) + see also spi-bus.txt + +Example: + +spi1@7e215080 { + compatible = "brcm,bcm2835-aux-spi"; + reg = <0x7e215080 0x40>; + interrupts = <1 29>; + clocks = <&aux_clocks BCM2835_AUX_CLOCK_SPI1>; + #address-cells = <1>; + #size-cells = <0>; + cs-gpios = <&gpio 18>, <&gpio 17>, <&gpio 16>; +}; + +spi2@7e2150c0 { + compatible = "brcm,bcm2835-aux-spi"; + reg = <0x7e2150c0 0x40>; + interrupts = <1 29>; + clocks = <&aux_clocks BCM2835_AUX_CLOCK_SPI2>; + #address-cells = <1>; + #size-cells = <0>; + cs-gpios = <&gpio 43>, <&gpio 44>, <&gpio 45>; +}; diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index 8f771441be60..705075da2f10 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -51,7 +51,7 @@ Optional properties, deprecated for soctype-specific bindings: - renesas,tx-fifo-size : Overrides the default tx fifo size given in words (default is 64) - renesas,rx-fifo-size : Overrides the default rx fifo size given in words - (default is 64, or 256 on R-Car Gen2) + (default is 64) Pinctrl properties might be needed, too. See Documentation/devicetree/bindings/pinctrl/renesas,*. diff --git a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt index 6160ffbcb3d3..ce363c923f44 100644 --- a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt +++ b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt @@ -29,8 +29,11 @@ Required properties: muxes clock, and "spi-clk" for the clock gate. Optional properties: +-cs-gpios: see spi-bus.txt, only required for MT8173. + - mediatek,pad-select: specify which pins group(ck/mi/mo/cs) spi - controller used, this value should be 0~3, only required for MT8173. + controller used. This is a array, the element value should be 0~3, + only required for MT8173. 0: specify GPIO69,70,71,72 for spi pins. 1: specify GPIO102,103,104,105 for spi pins. 2: specify GPIO128,129,130,131 for spi pins. @@ -49,7 +52,7 @@ spi: spi@1100a000 { <&topckgen CLK_TOP_SPI_SEL>, <&pericfg CLK_PERI_SPI0>; clock-names = "parent-clk", "sel-clk", "spi-clk"; - - mediatek,pad-select = <0>; + cs-gpios = <&pio 105 GPIO_ACTIVE_LOW>, <&pio 72 GPIO_ACTIVE_LOW>; + mediatek,pad-select = <1>, <0>; status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index a057b75ba4b5..781296bfbe4f 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -27,10 +27,6 @@ Optional properties: - vbus-supply: reference to the VBUS regulator - maximum-speed: limit the maximum connection speed to "full-speed". - tpl-support: TPL (Targeted Peripheral List) feature for targeted hosts -- fsl,usbmisc: (FSL only) phandler of non-core register device, with one - argument that indicate usb controller index -- disable-over-current: (FSL only) disable over current detect -- external-vbus-divider: (FSL only) enables off-chip resistor divider for Vbus - itc-setting: interrupt threshold control register control, the setting should be aligned with ITC bits at register USBCMD. - ahb-burst-config: it is vendor dependent, the required value should be @@ -41,11 +37,28 @@ Optional properties: - tx-burst-size-dword: it is vendor dependent, the tx burst size in dword (4 bytes), This register represents the maximum length of a the burst in 32-bit words while moving data from system memory to the USB - bus, changing this value takes effect only the SBUSCFG.AHBBRST is 0. + bus, the value of this property will only take effect if property + "ahb-burst-config" is set to 0, if this property is missing the reset + default of the hardware implementation will be used. - rx-burst-size-dword: it is vendor dependent, the rx burst size in dword (4 bytes), This register represents the maximum length of a the burst in 32-bit words while moving data from the USB bus to system memory, - changing this value takes effect only the SBUSCFG.AHBBRST is 0. + the value of this property will only take effect if property + "ahb-burst-config" is set to 0, if this property is missing the reset + default of the hardware implementation will be used. +- extcon: phandles to external connector devices. First phandle should point to + external connector, which provide "USB" cable events, the second should point + to external connector device, which provide "USB-HOST" cable events. If one + of the external connector devices is not required, empty <0> phandle should + be specified. +- phy-clkgate-delay-us: the delay time (us) between putting the PHY into + low power mode and gating the PHY clock. + +i.mx specific properties +- fsl,usbmisc: phandler of non-core register device, with one + argument that indicate usb controller index +- disable-over-current: disable over current detect +- external-vbus-divider: enables off-chip resistor divider for Vbus Example: @@ -62,4 +75,6 @@ Example: ahb-burst-config = <0x0>; tx-burst-size-dword = <0x10>; /* 64 bytes */ rx-burst-size-dword = <0x10>; + extcon = <0>, <&usb_id>; + phy-clkgate-delay-us = <400>; }; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index 0815eac5b185..9ff48e0defb4 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -35,11 +35,16 @@ Optional properties: LTSSM during USB3 Compliance mode. - snps,dis_u3_susphy_quirk: when set core will disable USB3 suspend phy. - snps,dis_u2_susphy_quirk: when set core will disable USB2 suspend phy. + - snps,dis_enblslpm_quirk: when set clears the enblslpm in GUSB2PHYCFG, + disabling the suspend signal to the PHY. - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal utmi_l1_suspend_n, false when asserts utmi_sleep_n - snps,hird-threshold: HIRD threshold - snps,hsphy_interface: High-Speed PHY interface selection between "utmi" for UTMI+ and "ulpi" for ULPI when the DWC_USB3_HSPHY_INTERFACE has value 3. + - snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ + register for post-silicon frame length adjustment when the + fladj_30mhz_sdbnd signal is invalid or incorrect. This is usually a subnode to DWC3 glue to which it is connected. diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt index 64a4ca6cf96f..7d48f63db44e 100644 --- a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt +++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt @@ -5,6 +5,7 @@ Required properties: - "renesas,usbhs-r8a7790" - "renesas,usbhs-r8a7791" - "renesas,usbhs-r8a7794" + - "renesas,usbhs-r8a7795" - reg: Base address and length of the register for the USBHS - interrupts: Interrupt specifier for the USBHS - clocks: A list of phandle + clock specifier pairs diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 82d2ac97af74..13e54a0e78b9 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -101,6 +101,7 @@ himax Himax Technologies, Inc. hisilicon Hisilicon Limited. hit Hitachi Ltd. hitex Hitex Development Tools +holt Holt Integrated Circuits, Inc. honeywell Honeywell hp Hewlett Packard i2se I2SE GmbH @@ -169,6 +170,7 @@ phytec PHYTEC Messtechnik GmbH picochip Picochip Ltd plathome Plat'Home Co., Ltd. pixcir PIXCIR MICROELECTRONICS Co., Ltd +pulsedlight PulsedLight, Inc powervr PowerVR (deprecated, use img) qca Qualcomm Atheros, Inc. qcom Qualcomm Technologies, Inc @@ -191,6 +193,7 @@ sbs Smart Battery System schindler Schindler seagate Seagate Technology PLC semtech Semtech Corporation +sgx SGX Sensortech sharp Sharp Corporation sil Silicon Image silabs Silicon Laboratories @@ -223,6 +226,7 @@ toshiba Toshiba Corporation toumaz Toumaz tplink TP-LINK Technologies Co., Ltd. truly Truly Semiconductors Limited +upisemi uPI Semiconductor Corp. usi Universal Scientific Industrial Co., Ltd. v3 V3 Semiconductor variscite Variscite Ltd. diff --git a/Documentation/devicetree/bindings/w1/omap-hdq.txt b/Documentation/devicetree/bindings/w1/omap-hdq.txt index fef794741bd1..913c5f91a0f9 100644 --- a/Documentation/devicetree/bindings/w1/omap-hdq.txt +++ b/Documentation/devicetree/bindings/w1/omap-hdq.txt @@ -1,11 +1,15 @@ * OMAP HDQ One wire bus master controller Required properties: -- compatible : should be "ti,omap3-1w" +- compatible : should be "ti,omap3-1w" or "ti,am4372-hdq" - reg : Address and length of the register set for the device - interrupts : interrupt line. - ti,hwmods : "hdq1w" +Optional properties: +- ti,mode: should be "hdq": HDQ mode "1w": one-wire mode. + If not specified HDQ mode is implied. + Example: - From omap3.dtsi @@ -14,4 +18,5 @@ Example: reg = <0x480b2000 0x1000>; interrupts = <58>; ti,hwmods = "hdq1w"; + ti,mode = "hdq"; }; |