diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
17 files changed, 66 insertions, 31 deletions
diff --git a/Documentation/devicetree/bindings/arm/atmel-aic.txt b/Documentation/devicetree/bindings/arm/atmel-aic.txt index 19078bf5cca8..ad031211b5b8 100644 --- a/Documentation/devicetree/bindings/arm/atmel-aic.txt +++ b/Documentation/devicetree/bindings/arm/atmel-aic.txt @@ -4,7 +4,7 @@ Required properties: - compatible: Should be "atmel,<chip>-aic" - interrupt-controller: Identifies the node as an interrupt controller. - interrupt-parent: For single AIC system, it is an empty property. -- #interrupt-cells: The number of cells to define the interrupts. It sould be 3. +- #interrupt-cells: The number of cells to define the interrupts. It should be 3. The first cell is the IRQ number (aka "Peripheral IDentifier" on datasheet). The second cell is used to specify flags: bits[3:0] trigger type and level flags: diff --git a/Documentation/devicetree/bindings/arm/gic.txt b/Documentation/devicetree/bindings/arm/gic.txt index 62eb8df1e08d..3dfb0c0384f5 100644 --- a/Documentation/devicetree/bindings/arm/gic.txt +++ b/Documentation/devicetree/bindings/arm/gic.txt @@ -42,7 +42,7 @@ Main node required properties: Optional - interrupts : Interrupt source of the parent interrupt controller on - secondary GICs, or VGIC maintainance interrupt on primary GIC (see + secondary GICs, or VGIC maintenance interrupt on primary GIC (see below). - cpu-offset : per-cpu offset within the distributor and cpu interface @@ -74,7 +74,7 @@ Required properties: virtual interface control register base and size. The 2nd additional region is the GIC virtual cpu interface register base and size. -- interrupts : VGIC maintainance interrupt. +- interrupts : VGIC maintenance interrupt. Example: diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index d0051a750587..f8288ea1b530 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -39,16 +39,16 @@ Boards: - OMAP3 Tobi with Overo : Commercial expansion board with daughter board compatible = "ti,omap3-tobi", "ti,omap3-overo", "ti,omap3" -- OMAP4 SDP : Software Developement Board +- OMAP4 SDP : Software Development Board compatible = "ti,omap4-sdp", "ti,omap4430" - OMAP4 PandaBoard : Low cost community board compatible = "ti,omap4-panda", "ti,omap4430" -- OMAP3 EVM : Software Developement Board for OMAP35x, AM/DM37x +- OMAP3 EVM : Software Development Board for OMAP35x, AM/DM37x compatible = "ti,omap3-evm", "ti,omap3" -- AM335X EVM : Software Developement Board for AM335x +- AM335X EVM : Software Development Board for AM335x compatible = "ti,am335x-evm", "ti,am33xx", "ti,omap3" - AM335X Bone : Low cost community board diff --git a/Documentation/devicetree/bindings/drm/exynos/g2d.txt b/Documentation/devicetree/bindings/drm/exynos/g2d.txt new file mode 100644 index 000000000000..1eb124d35a99 --- /dev/null +++ b/Documentation/devicetree/bindings/drm/exynos/g2d.txt @@ -0,0 +1,22 @@ +Samsung 2D Graphic Accelerator using DRM frame work + +Samsung FIMG2D is a graphics 2D accelerator which supports Bit Block Transfer. +We set the drawing-context registers for configuring rendering parameters and +then start rendering. +This driver is for SOCs which contain G2D IPs with version 4.1. + +Required properties: + -compatible: + should be "samsung,exynos-g2d-41". + -reg: + physical base address of the controller and length + of memory mapped region. + -interrupts: + interrupt combiner values. + +Example: + g2d { + compatible = "samsung,exynos-g2d-41"; + reg = <0x10850000 0x1000>; + interrupts = <0 91 0>; + }; diff --git a/Documentation/devicetree/bindings/input/lpc32xx-key.txt b/Documentation/devicetree/bindings/input/lpc32xx-key.txt index 31afd5014c48..bcf62f856358 100644 --- a/Documentation/devicetree/bindings/input/lpc32xx-key.txt +++ b/Documentation/devicetree/bindings/input/lpc32xx-key.txt @@ -1,19 +1,22 @@ NXP LPC32xx Key Scan Interface +This binding is based on the matrix-keymap binding with the following +changes: + Required Properties: - compatible: Should be "nxp,lpc3220-key" - reg: Physical base address of the controller and length of memory mapped region. - interrupts: The interrupt number to the cpu. -- keypad,num-rows: Number of rows and columns, e.g. 1: 1x1, 6: 6x6 -- keypad,num-columns: Must be equal to keypad,num-rows since LPC32xx only - supports square matrices - nxp,debounce-delay-ms: Debounce delay in ms - nxp,scan-delay-ms: Repeated scan period in ms - linux,keymap: the key-code to be reported when the key is pressed and released, see also Documentation/devicetree/bindings/input/matrix-keymap.txt +Note: keypad,num-rows and keypad,num-columns are required, and must be equal +since LPC32xx only supports square matrices + Example: key@40050000 { diff --git a/Documentation/devicetree/bindings/input/matrix-keymap.txt b/Documentation/devicetree/bindings/input/matrix-keymap.txt index 3cd8b98ccd2d..c54919fad17e 100644 --- a/Documentation/devicetree/bindings/input/matrix-keymap.txt +++ b/Documentation/devicetree/bindings/input/matrix-keymap.txt @@ -9,6 +9,12 @@ Required properties: row << 24 | column << 16 | key-code Optional properties: +Properties for the number of rows and columns are optional because some +drivers will use fixed values for these. +- keypad,num-rows: Number of row lines connected to the keypad controller. +- keypad,num-columns: Number of column lines connected to the keypad + controller. + Some users of this binding might choose to specify secondary keymaps for cases where there is a modifier key such as a Fn key. Proposed names for said properties are "linux,fn-keymap" or with another descriptive @@ -17,3 +23,5 @@ word for the modifier other from "Fn". Example: linux,keymap = < 0x00030012 0x0102003a >; + keypad,num-rows = <2>; + keypad,num-columns = <8>; diff --git a/Documentation/devicetree/bindings/input/omap-keypad.txt b/Documentation/devicetree/bindings/input/omap-keypad.txt index f2fa5e10493d..34ed1c60ff95 100644 --- a/Documentation/devicetree/bindings/input/omap-keypad.txt +++ b/Documentation/devicetree/bindings/input/omap-keypad.txt @@ -6,19 +6,16 @@ A key can be placed at each intersection of a unique row and a unique column. The keypad controller can sense a key-press and key-release and report the event using a interrupt to the cpu. +This binding is based on the matrix-keymap binding with the following +changes: + +keypad,num-rows and keypad,num-columns are required. + Required SoC Specific Properties: - compatible: should be one of the following - "ti,omap4-keypad": For controllers compatible with omap4 keypad controller. -Required Board Specific Properties, in addition to those specified by -the shared matrix-keyboard bindings: -- keypad,num-rows: Number of row lines connected to the keypad - controller. - -- keypad,num-columns: Number of column lines connected to the - keypad controller. - Optional Properties specific to linux: - linux,keypad-no-autorepeat: do no enable autorepeat feature. diff --git a/Documentation/devicetree/bindings/input/tca8418_keypad.txt b/Documentation/devicetree/bindings/input/tca8418_keypad.txt index 2a1538f0053f..255185009167 100644 --- a/Documentation/devicetree/bindings/input/tca8418_keypad.txt +++ b/Documentation/devicetree/bindings/input/tca8418_keypad.txt @@ -1,8 +1,10 @@ +This binding is based on the matrix-keymap binding with the following +changes: + +keypad,num-rows and keypad,num-columns are required. Required properties: - compatible: "ti,tca8418" - reg: the I2C address - interrupts: IRQ line number, should trigger on falling edge -- keypad,num-rows: The number of rows -- keypad,num-columns: The number of columns - linux,keymap: Keys definitions, see keypad-matrix. diff --git a/Documentation/devicetree/bindings/gpio/leds-ns2.txt b/Documentation/devicetree/bindings/leds/leds-ns2.txt index aef3aca34d2d..aef3aca34d2d 100644 --- a/Documentation/devicetree/bindings/gpio/leds-ns2.txt +++ b/Documentation/devicetree/bindings/leds/leds-ns2.txt diff --git a/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt b/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt index cb4291e3b1d1..a5bdff400002 100644 --- a/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt +++ b/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt @@ -1,7 +1,7 @@ * DMA Engine. The Octeon DMA Engine transfers between the Boot Bus and main memory. -The DMA Engine will be refered to by phandle by any device that is +The DMA Engine will be referred to by phandle by any device that is connected to it. Properties: diff --git a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt index 792768953330..6d1c0988cfc7 100644 --- a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt @@ -4,18 +4,18 @@ The Synopsis designware mobile storage host controller is used to interface a SoC with storage medium such as eMMC or SD/MMC cards. This file documents differences between the core Synopsis dw mshc controller properties described -by synposis-dw-mshc.txt and the properties used by the Samsung Exynos specific +by synopsis-dw-mshc.txt and the properties used by the Samsung Exynos specific extensions to the Synopsis Designware Mobile Storage Host Controller. Required Properties: * compatible: should be - "samsung,exynos4210-dw-mshc": for controllers with Samsung Exynos4210 - specific extentions. + specific extensions. - "samsung,exynos4412-dw-mshc": for controllers with Samsung Exynos4412 - specific extentions. + specific extensions. - "samsung,exynos5250-dw-mshc": for controllers with Samsung Exynos5250 - specific extentions. + specific extensions. * samsung,dw-mshc-ciu-div: Specifies the divider value for the card interface unit (ciu) clock. This property is applicable only for Exynos5 SoC's and diff --git a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt index 97e9e315400d..3b3a1ee055ff 100644 --- a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt @@ -55,5 +55,5 @@ Example: }; Note: This example shows both SoC specific and board specific properties - in a single device node. The properties can be actually be seperated + in a single device node. The properties can be actually be separated into SoC specific node and board specific node. diff --git a/Documentation/devicetree/bindings/powerpc/fsl/srio.txt b/Documentation/devicetree/bindings/powerpc/fsl/srio.txt index b039bcbee134..07abf0f2f440 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/srio.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/srio.txt @@ -8,9 +8,9 @@ Properties: Definition: Must include "fsl,srio" for IP blocks with IP Block Revision Register (SRIO IPBRR1) Major ID equal to 0x01c0. - Optionally, a compatiable string of "fsl,srio-vX.Y" where X is Major + Optionally, a compatible string of "fsl,srio-vX.Y" where X is Major version in IP Block Revision Register and Y is Minor version. If this - compatiable is provided it should be ordered before "fsl,srio". + compatible is provided it should be ordered before "fsl,srio". - reg Usage: required diff --git a/Documentation/devicetree/bindings/regulator/tps62360-regulator.txt b/Documentation/devicetree/bindings/regulator/tps62360-regulator.txt index c8ca6b8f6582..1b20c3dbcdb8 100644 --- a/Documentation/devicetree/bindings/regulator/tps62360-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/tps62360-regulator.txt @@ -17,9 +17,9 @@ Optional properties: - ti,vsel1-gpio: Gpio for controlling VSEL1 line. If this property is missing, then assume that there is no GPIO for vsel1 control. -- ti,vsel0-state-high: Inital state of vsel0 input is high. +- ti,vsel0-state-high: Initial state of vsel0 input is high. If this property is missing, then assume the state as low (0). -- ti,vsel1-state-high: Inital state of vsel1 input is high. +- ti,vsel1-state-high: Initial state of vsel1 input is high. If this property is missing, then assume the state as low (0). Any property defined as part of the core regulator binding, defined in diff --git a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt index 90ec45fd33ec..7ac7259fe9ea 100644 --- a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt @@ -7,7 +7,7 @@ Required properties: - reg: physical base address of the controller and length of memory mapped region. - interrupts: Two interrupt numbers to the cpu should be specified. First - interrupt number is the rtc alarm interupt and second interrupt number + interrupt number is the rtc alarm interrupt and second interrupt number is the rtc tick interrupt. The number of cells representing a interrupt depends on the parent interrupt controller. diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 15321373ec8d..19e1ef73ab0d 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -14,6 +14,7 @@ bosch Bosch Sensortec GmbH brcm Broadcom Corporation cavium Cavium, Inc. chrp Common Hardware Reference Platform +cirrus Cirrus Logic, Inc. cortina Cortina Systems, Inc. dallas Maxim Integrated Products (formerly Dallas Semiconductor) denx Denx Software Engineering @@ -42,6 +43,7 @@ powervr PowerVR (deprecated, use img) qcom Qualcomm, Inc. ramtron Ramtron International realtek Realtek Semiconductor Corp. +renesas Renesas Electronics Corporation samsung Samsung Semiconductor sbs Smart Battery System schindler Schindler @@ -53,6 +55,7 @@ st STMicroelectronics ste ST-Ericsson stericsson ST-Ericsson ti Texas Instruments +toshiba Toshiba Corporation via VIA Technologies, Inc. wlf Wolfson Microelectronics wm Wondermedia Technologies, Inc. diff --git a/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt index 79ead8263ae4..ce0d8e78ed8f 100644 --- a/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt @@ -2,7 +2,7 @@ The Samsung's Watchdog controller is used for resuming system operation after a preset amount of time during which the WDT reset event has not -occured. +occurred. Required properties: - compatible : should be "samsung,s3c2410-wdt" |