diff options
Diffstat (limited to 'Documentation/devicetree')
5 files changed, 95 insertions, 9 deletions
diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt b/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt index 947863acc2d4..7b94c88cf2ee 100644 --- a/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt +++ b/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt @@ -1,6 +1,6 @@ * ARM SMMUv3 Architecture Implementation -The SMMUv3 architecture is a significant deparature from previous +The SMMUv3 architecture is a significant departure from previous revisions, replacing the MMIO register interface with in-memory command and event queues and adding support for the ATS and PRI components of the PCIe specification. diff --git a/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt b/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt index cd1b1cd7b5c4..53c20cae309f 100644 --- a/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt +++ b/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt @@ -1,7 +1,9 @@ * Mediatek IOMMU Architecture Implementation - Some Mediatek SOCs contain a Multimedia Memory Management Unit (M4U) which -uses the ARM Short-Descriptor translation table format for address translation. + Some Mediatek SOCs contain a Multimedia Memory Management Unit (M4U), and +this M4U have two generations of HW architecture. Generation one uses flat +pagetable, and only supports 4K size page mapping. Generation two uses the +ARM Short-Descriptor translation table format for address translation. About the M4U Hardware Block Diagram, please check below: @@ -36,7 +38,9 @@ in each larb. Take a example, There are many ports like MC, PP, VLD in the video decode local arbiter, all these ports are according to the video HW. Required properties: -- compatible : must be "mediatek,mt8173-m4u". +- compatible : must be one of the following string: + "mediatek,mt2701-m4u" for mt2701 which uses generation one m4u HW. + "mediatek,mt8173-m4u" for mt8173 which uses generation two m4u HW. - reg : m4u register base and size. - interrupts : the interrupt of m4u. - clocks : must contain one entry for each clock-names. @@ -46,7 +50,8 @@ Required properties: according to the local arbiter index, like larb0, larb1, larb2... - iommu-cells : must be 1. This is the mtk_m4u_id according to the HW. Specifies the mtk_m4u_id as defined in - dt-binding/memory/mt8173-larb-port.h. + dt-binding/memory/mt2701-larb-port.h for mt2701 and + dt-binding/memory/mt8173-larb-port.h for mt8173 Example: iommu: iommu@10205000 { diff --git a/Documentation/devicetree/bindings/iommu/msm,iommu-v0.txt b/Documentation/devicetree/bindings/iommu/msm,iommu-v0.txt new file mode 100644 index 000000000000..20236385f26e --- /dev/null +++ b/Documentation/devicetree/bindings/iommu/msm,iommu-v0.txt @@ -0,0 +1,64 @@ +* QCOM IOMMU + +The MSM IOMMU is an implementation compatible with the ARM VMSA short +descriptor page tables. It provides address translation for bus masters outside +of the CPU, each connected to the IOMMU through a port called micro-TLB. + +Required Properties: + + - compatible: Must contain "qcom,apq8064-iommu". + - reg: Base address and size of the IOMMU registers. + - interrupts: Specifiers for the MMU fault interrupts. For instances that + support secure mode two interrupts must be specified, for non-secure and + secure mode, in that order. For instances that don't support secure mode a + single interrupt must be specified. + - #iommu-cells: The number of cells needed to specify the stream id. This + is always 1. + - qcom,ncb: The total number of context banks in the IOMMU. + - clocks : List of clocks to be used during SMMU register access. See + Documentation/devicetree/bindings/clock/clock-bindings.txt + for information about the format. For each clock specified + here, there must be a corresponding entry in clock-names + (see below). + + - clock-names : List of clock names corresponding to the clocks specified in + the "clocks" property (above). + Should be "smmu_pclk" for specifying the interface clock + required for iommu's register accesses. + Should be "smmu_clk" for specifying the functional clock + required by iommu for bus accesses. + +Each bus master connected to an IOMMU must reference the IOMMU in its device +node with the following property: + + - iommus: A reference to the IOMMU in multiple cells. The first cell is a + phandle to the IOMMU and the second cell is the stream id. + A single master device can be connected to more than one iommu + and multiple contexts in each of the iommu. So multiple entries + are required to list all the iommus and the stream ids that the + master is connected to. + +Example: mdp iommu and its bus master + + mdp_port0: iommu@7500000 { + compatible = "qcom,apq8064-iommu"; + #iommu-cells = <1>; + clock-names = + "smmu_pclk", + "smmu_clk"; + clocks = + <&mmcc SMMU_AHB_CLK>, + <&mmcc MDP_AXI_CLK>; + reg = <0x07500000 0x100000>; + interrupts = + <GIC_SPI 63 0>, + <GIC_SPI 64 0>; + qcom,ncb = <2>; + }; + + mdp: qcom,mdp@5100000 { + compatible = "qcom,mdp"; + ... + iommus = <&mdp_port0 0 + &mdp_port0 2>; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt index 06a83ceebba7..aa614b2d7cab 100644 --- a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt +++ b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt @@ -2,16 +2,31 @@ SMI (Smart Multimedia Interface) Common The hardware block diagram please check bindings/iommu/mediatek,iommu.txt +Mediatek SMI have two generations of HW architecture, mt8173 uses the second +generation of SMI HW while mt2701 uses the first generation HW of SMI. + +There's slight differences between the two SMI, for generation 2, the +register which control the iommu port is at each larb's register base. But +for generation 1, the register is at smi ao base(smi always on register +base). Besides that, the smi async clock should be prepared and enabled for +SMI generation 1 to transform the smi clock into emi clock domain, but that is +not needed for SMI generation 2. + Required properties: -- compatible : must be "mediatek,mt8173-smi-common" +- compatible : must be one of : + "mediatek,mt2701-smi-common" + "mediatek,mt8173-smi-common" - reg : the register and size of the SMI block. - power-domains : a phandle to the power domain of this local arbiter. - clocks : Must contain an entry for each entry in clock-names. -- clock-names : must contain 2 entries, as follows: +- clock-names : must contain 3 entries for generation 1 smi HW and 2 entries + for generation 2 smi HW as follows: - "apb" : Advanced Peripheral Bus clock, It's the clock for setting the register. - "smi" : It's the clock for transfer data and command. - They may be the same if both source clocks are the same. + They may be the same if both source clocks are the same. + - "async" : asynchronous clock, it help transform the smi clock into the emi + clock domain, this clock is only needed by generation 1 smi HW. Example: smi_common: smi@14022000 { diff --git a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt index 55ff3b7e0bb9..21277a56e94c 100644 --- a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt +++ b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt @@ -3,7 +3,9 @@ SMI (Smart Multimedia Interface) Local Arbiter The hardware block diagram please check bindings/iommu/mediatek,iommu.txt Required properties: -- compatible : must be "mediatek,mt8173-smi-larb" +- compatible : must be one of : + "mediatek,mt8173-smi-larb" + "mediatek,mt2701-smi-larb" - reg : the register and size of this local arbiter. - mediatek,smi : a phandle to the smi_common node. - power-domains : a phandle to the power domain of this local arbiter. |