diff options
Diffstat (limited to 'Documentation/devicetree')
| -rw-r--r-- | Documentation/devicetree/bindings/arm/cpus.txt | 17 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/cpufreq/cpufreq-st.txt | 91 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/opp/opp.txt | 132 |
3 files changed, 201 insertions, 39 deletions
diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index 3a07a87fef20..6aca64f289b6 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -242,6 +242,23 @@ nodes to be present and contain the properties described below. Definition: Specifies the syscon node controlling the cpu core power domains. + - dynamic-power-coefficient + Usage: optional + Value type: <prop-encoded-array> + Definition: A u32 value that represents the running time dynamic + power coefficient in units of mW/MHz/uVolt^2. The + coefficient can either be calculated from power + measurements or derived by analysis. + + The dynamic power consumption of the CPU is + proportional to the square of the Voltage (V) and + the clock frequency (f). The coefficient is used to + calculate the dynamic power as below - + + Pdyn = dynamic-power-coefficient * V^2 * f + + where voltage is in uV, frequency is in MHz. + Example 1 (dual-cluster big.LITTLE system 32-bit): cpus { diff --git a/Documentation/devicetree/bindings/cpufreq/cpufreq-st.txt b/Documentation/devicetree/bindings/cpufreq/cpufreq-st.txt new file mode 100644 index 000000000000..d91a02a3b6b0 --- /dev/null +++ b/Documentation/devicetree/bindings/cpufreq/cpufreq-st.txt @@ -0,0 +1,91 @@ +Binding for ST's CPUFreq driver +=============================== + +ST's CPUFreq driver attempts to read 'process' and 'version' attributes +from the SoC, then supplies the OPP framework with 'prop' and 'supported +hardware' information respectively. The framework is then able to read +the DT and operate in the usual way. + +For more information about the expected DT format [See: ../opp/opp.txt]. + +Frequency Scaling only +---------------------- + +No vendor specific driver required for this. + +Located in CPU's node: + +- operating-points : [See: ../power/opp.txt] + +Example [safe] +-------------- + +cpus { + cpu@0 { + /* kHz uV */ + operating-points = <1500000 0 + 1200000 0 + 800000 0 + 500000 0>; + }; +}; + +Dynamic Voltage and Frequency Scaling (DVFS) +-------------------------------------------- + +This requires the ST CPUFreq driver to supply 'process' and 'version' info. + +Located in CPU's node: + +- operating-points-v2 : [See ../power/opp.txt] + +Example [unsafe] +---------------- + +cpus { + cpu@0 { + operating-points-v2 = <&cpu0_opp_table>; + }; +}; + +cpu0_opp_table: opp_table { + compatible = "operating-points-v2"; + + /* ############################################################### */ + /* # WARNING: Do not attempt to copy/replicate these nodes, # */ + /* # they are only to be supplied by the bootloader !!! # */ + /* ############################################################### */ + opp0 { + /* Major Minor Substrate */ + /* 2 all all */ + opp-supported-hw = <0x00000004 0xffffffff 0xffffffff>; + opp-hz = /bits/ 64 <1500000000>; + clock-latency-ns = <10000000>; + + opp-microvolt-pcode0 = <1200000>; + opp-microvolt-pcode1 = <1200000>; + opp-microvolt-pcode2 = <1200000>; + opp-microvolt-pcode3 = <1200000>; + opp-microvolt-pcode4 = <1170000>; + opp-microvolt-pcode5 = <1140000>; + opp-microvolt-pcode6 = <1100000>; + opp-microvolt-pcode7 = <1070000>; + }; + + opp1 { + /* Major Minor Substrate */ + /* all all all */ + opp-supported-hw = <0xffffffff 0xffffffff 0xffffffff>; + opp-hz = /bits/ 64 <1200000000>; + clock-latency-ns = <10000000>; + + opp-microvolt-pcode0 = <1110000>; + opp-microvolt-pcode1 = <1150000>; + opp-microvolt-pcode2 = <1100000>; + opp-microvolt-pcode3 = <1080000>; + opp-microvolt-pcode4 = <1040000>; + opp-microvolt-pcode5 = <1020000>; + opp-microvolt-pcode6 = <980000>; + opp-microvolt-pcode7 = <930000>; + }; +}; diff --git a/Documentation/devicetree/bindings/opp/opp.txt b/Documentation/devicetree/bindings/opp/opp.txt index 0cb44dc21f97..601256fe8c0d 100644 --- a/Documentation/devicetree/bindings/opp/opp.txt +++ b/Documentation/devicetree/bindings/opp/opp.txt @@ -45,21 +45,10 @@ Devices supporting OPPs must set their "operating-points-v2" property with phandle to a OPP table in their DT node. The OPP core will use this phandle to find the operating points for the device. -Devices may want to choose OPP tables at runtime and so can provide a list of -phandles here. But only *one* of them should be chosen at runtime. This must be -accompanied by a corresponding "operating-points-names" property, to uniquely -identify the OPP tables. - If required, this can be extended for SoC vendor specfic bindings. Such bindings should be documented as Documentation/devicetree/bindings/power/<vendor>-opp.txt and should have a compatible description like: "operating-points-v2-<vendor>". -Optional properties: -- operating-points-names: Names of OPP tables (required if multiple OPP - tables are present), to uniquely identify them. The same list must be present - for all the CPUs which are sharing clock/voltage rails and hence the OPP - tables. - * OPP Table Node This describes the OPPs belonging to a device. This node can have following @@ -100,6 +89,14 @@ Optional properties: Entries for multiple regulators must be present in the same order as regulators are specified in device's DT node. +- opp-microvolt-<name>: Named opp-microvolt property. This is exactly similar to + the above opp-microvolt property, but allows multiple voltage ranges to be + provided for the same OPP. At runtime, the platform can pick a <name> and + matching opp-microvolt-<name> property will be enabled for all OPPs. If the + platform doesn't pick a specific <name> or the <name> doesn't match with any + opp-microvolt-<name> properties, then opp-microvolt property shall be used, if + present. + - opp-microamp: The maximum current drawn by the device in microamperes considering system specific parameters (such as transients, process, aging, maximum operating temperature range etc.) as necessary. This may be used to @@ -112,6 +109,9 @@ Optional properties: for few regulators, then this should be marked as zero for them. If it isn't required for any regulator, then this property need not be present. +- opp-microamp-<name>: Named opp-microamp property. Similar to + opp-microvolt-<name> property, but for microamp instead. + - clock-latency-ns: Specifies the maximum possible transition latency (in nanoseconds) for switching to this OPP from any other OPP. @@ -123,6 +123,26 @@ Optional properties: - opp-suspend: Marks the OPP to be used during device suspend. Only one OPP in the table should have this. +- opp-supported-hw: This enables us to select only a subset of OPPs from the + larger OPP table, based on what version of the hardware we are running on. We + still can't have multiple nodes with the same opp-hz value in OPP table. + + It's an user defined array containing a hierarchy of hardware version numbers, + supported by the OPP. For example: a platform with hierarchy of three levels + of versions (A, B and C), this field should be like <X Y Z>, where X + corresponds to Version hierarchy A, Y corresponds to version hierarchy B and Z + corresponds to version hierarchy C. + + Each level of hierarchy is represented by a 32 bit value, and so there can be + only 32 different supported version per hierarchy. i.e. 1 bit per version. A + value of 0xFFFFFFFF will enable the OPP for all versions for that hierarchy + level. And a value of 0x00000000 will disable the OPP completely, and so we + never want that to happen. + + If 32 values aren't sufficient for a version hierarchy, than that version + hierarchy can be contained in multiple 32 bit values. i.e. <X Y Z1 Z2> in the + above example, Z1 & Z2 refer to the version hierarchy Z. + - status: Marks the node enabled/disabled. Example 1: Single cluster Dual-core ARM cortex A9, switch DVFS states together. @@ -157,20 +177,20 @@ Example 1: Single cluster Dual-core ARM cortex A9, switch DVFS states together. compatible = "operating-points-v2"; opp-shared; - opp00 { + opp@1000000000 { opp-hz = /bits/ 64 <1000000000>; opp-microvolt = <970000 975000 985000>; opp-microamp = <70000>; clock-latency-ns = <300000>; opp-suspend; }; - opp01 { + opp@1100000000 { opp-hz = /bits/ 64 <1100000000>; opp-microvolt = <980000 1000000 1010000>; opp-microamp = <80000>; clock-latency-ns = <310000>; }; - opp02 { + opp@1200000000 { opp-hz = /bits/ 64 <1200000000>; opp-microvolt = <1025000>; clock-latency-ns = <290000>; @@ -236,20 +256,20 @@ independently. * independently. */ - opp00 { + opp@1000000000 { opp-hz = /bits/ 64 <1000000000>; opp-microvolt = <970000 975000 985000>; opp-microamp = <70000>; clock-latency-ns = <300000>; opp-suspend; }; - opp01 { + opp@1100000000 { opp-hz = /bits/ 64 <1100000000>; opp-microvolt = <980000 1000000 1010000>; opp-microamp = <80000>; clock-latency-ns = <310000>; }; - opp02 { + opp@1200000000 { opp-hz = /bits/ 64 <1200000000>; opp-microvolt = <1025000>; opp-microamp = <90000; @@ -312,20 +332,20 @@ DVFS state together. compatible = "operating-points-v2"; opp-shared; - opp00 { + opp@1000000000 { opp-hz = /bits/ 64 <1000000000>; opp-microvolt = <970000 975000 985000>; opp-microamp = <70000>; clock-latency-ns = <300000>; opp-suspend; }; - opp01 { + opp@1100000000 { opp-hz = /bits/ 64 <1100000000>; opp-microvolt = <980000 1000000 1010000>; opp-microamp = <80000>; clock-latency-ns = <310000>; }; - opp02 { + opp@1200000000 { opp-hz = /bits/ 64 <1200000000>; opp-microvolt = <1025000>; opp-microamp = <90000>; @@ -338,20 +358,20 @@ DVFS state together. compatible = "operating-points-v2"; opp-shared; - opp10 { + opp@1300000000 { opp-hz = /bits/ 64 <1300000000>; opp-microvolt = <1045000 1050000 1055000>; opp-microamp = <95000>; clock-latency-ns = <400000>; opp-suspend; }; - opp11 { + opp@1400000000 { opp-hz = /bits/ 64 <1400000000>; opp-microvolt = <1075000>; opp-microamp = <100000>; clock-latency-ns = <400000>; }; - opp12 { + opp@1500000000 { opp-hz = /bits/ 64 <1500000000>; opp-microvolt = <1010000 1100000 1110000>; opp-microamp = <95000>; @@ -378,7 +398,7 @@ Example 4: Handling multiple regulators compatible = "operating-points-v2"; opp-shared; - opp00 { + opp@1000000000 { opp-hz = /bits/ 64 <1000000000>; opp-microvolt = <970000>, /* Supply 0 */ <960000>, /* Supply 1 */ @@ -391,7 +411,7 @@ Example 4: Handling multiple regulators /* OR */ - opp00 { + opp@1000000000 { opp-hz = /bits/ 64 <1000000000>; opp-microvolt = <970000 975000 985000>, /* Supply 0 */ <960000 965000 975000>, /* Supply 1 */ @@ -404,7 +424,7 @@ Example 4: Handling multiple regulators /* OR */ - opp00 { + opp@1000000000 { opp-hz = /bits/ 64 <1000000000>; opp-microvolt = <970000 975000 985000>, /* Supply 0 */ <960000 965000 975000>, /* Supply 1 */ @@ -417,7 +437,8 @@ Example 4: Handling multiple regulators }; }; -Example 5: Multiple OPP tables +Example 5: opp-supported-hw +(example: three level hierarchy of versions: cuts, substrate and process) / { cpus { @@ -426,40 +447,73 @@ Example 5: Multiple OPP tables ... cpu-supply = <&cpu_supply> - operating-points-v2 = <&cpu0_opp_table_slow>, <&cpu0_opp_table_fast>; - operating-points-names = "slow", "fast"; + operating-points-v2 = <&cpu0_opp_table_slow>; }; }; - cpu0_opp_table_slow: opp_table_slow { + opp_table { compatible = "operating-points-v2"; status = "okay"; opp-shared; - opp00 { + opp@600000000 { + /* + * Supports all substrate and process versions for 0xF + * cuts, i.e. only first four cuts. + */ + opp-supported-hw = <0xF 0xFFFFFFFF 0xFFFFFFFF> opp-hz = /bits/ 64 <600000000>; + opp-microvolt = <900000 915000 925000>; ... }; - opp01 { + opp@800000000 { + /* + * Supports: + * - cuts: only one, 6th cut (represented by 6th bit). + * - substrate: supports 16 different substrate versions + * - process: supports 9 different process versions + */ + opp-supported-hw = <0x20 0xff0000ff 0x0000f4f0> opp-hz = /bits/ 64 <800000000>; + opp-microvolt = <900000 915000 925000>; ... }; }; +}; + +Example 6: opp-microvolt-<name>, opp-microamp-<name>: +(example: device with two possible microvolt ranges: slow and fast) - cpu0_opp_table_fast: opp_table_fast { +/ { + cpus { + cpu@0 { + compatible = "arm,cortex-a7"; + ... + + operating-points-v2 = <&cpu0_opp_table>; + }; + }; + + cpu0_opp_table: opp_table0 { compatible = "operating-points-v2"; - status = "okay"; opp-shared; - opp10 { + opp@1000000000 { opp-hz = /bits/ 64 <1000000000>; - ... + opp-microvolt-slow = <900000 915000 925000>; + opp-microvolt-fast = <970000 975000 985000>; + opp-microamp-slow = <70000>; + opp-microamp-fast = <71000>; }; - opp11 { - opp-hz = /bits/ 64 <1100000000>; - ... + opp@1200000000 { + opp-hz = /bits/ 64 <1200000000>; + opp-microvolt-slow = <900000 915000 925000>, /* Supply vcc0 */ + <910000 925000 935000>; /* Supply vcc1 */ + opp-microvolt-fast = <970000 975000 985000>, /* Supply vcc0 */ + <960000 965000 975000>; /* Supply vcc1 */ + opp-microamp = <70000>; /* Will be used for both slow/fast */ }; }; }; |