diff options
Diffstat (limited to 'Documentation/devicetree')
42 files changed, 523 insertions, 68 deletions
diff --git a/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt b/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt index e56a1df3a9d3..dd906db34b32 100644 --- a/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt +++ b/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt @@ -16,7 +16,20 @@ Required properties: - #clock-cells: Should be <1>. The permitted clock-specifier values can be found in include/dt-bindings/clock/bcm2835.h - reg: Specifies base physical address and size of the registers -- clocks: The external oscillator clock phandle +- clocks: phandles to the parent clocks used as input to the module, in + the following order: + + - External oscillator + - DSI0 byte clock + - DSI0 DDR2 clock + - DSI0 DDR clock + - DSI1 byte clock + - DSI1 DDR2 clock + - DSI1 DDR clock + + Only external oscillator is required. The DSI clocks may + not be present, in which case their children will be + unusable. Example: diff --git a/Documentation/devicetree/bindings/clock/exynos4415-clock.txt b/Documentation/devicetree/bindings/clock/exynos4415-clock.txt deleted file mode 100644 index 847d98bae8cf..000000000000 --- a/Documentation/devicetree/bindings/clock/exynos4415-clock.txt +++ /dev/null @@ -1,38 +0,0 @@ -* Samsung Exynos4415 Clock Controller - -The Exynos4415 clock controller generates and supplies clock to various -consumer devices within the Exynos4415 SoC. - -Required properties: - -- compatible: should be one of the following: - - "samsung,exynos4415-cmu" - for the main system clocks controller - (CMU_LEFTBUS, CMU_RIGHTBUS, CMU_TOP, CMU_CPU clock domains). - - "samsung,exynos4415-cmu-dmc" - for the Exynos4415 SoC DRAM Memory - Controller (DMC) domain clock controller. - -- reg: physical base address of the controller and length of memory mapped - region. - -- #clock-cells: should be 1. - -Each clock is assigned an identifier and client nodes can use this identifier -to specify the clock which they consume. - -All available clocks are defined as preprocessor macros in -dt-bindings/clock/exynos4415.h header and can be used in device -tree sources. - -Example 1: An example of a clock controller node is listed below. - - cmu: clock-controller@10030000 { - compatible = "samsung,exynos4415-cmu"; - reg = <0x10030000 0x18000>; - #clock-cells = <1>; - }; - - cmu-dmc: clock-controller@105C0000 { - compatible = "samsung,exynos4415-cmu-dmc"; - reg = <0x105C0000 0x3000>; - #clock-cells = <1>; - }; diff --git a/Documentation/devicetree/bindings/clock/hi3660-clock.txt b/Documentation/devicetree/bindings/clock/hi3660-clock.txt new file mode 100644 index 000000000000..cc9b86c35758 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/hi3660-clock.txt @@ -0,0 +1,42 @@ +* Hisilicon Hi3660 Clock Controller + +The Hi3660 clock controller generates and supplies clock to various +controllers within the Hi3660 SoC. + +Required Properties: + +- compatible: the compatible should be one of the following strings to + indicate the clock controller functionality. + + - "hisilicon,hi3660-crgctrl" + - "hisilicon,hi3660-pctrl" + - "hisilicon,hi3660-pmuctrl" + - "hisilicon,hi3660-sctrl" + - "hisilicon,hi3660-iomcu" + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes use this identifier +to specify the clock which they consume. + +All these identifier could be found in <dt-bindings/clock/hi3660-clock.h>. + +Examples: + crg_ctrl: clock-controller@fff35000 { + compatible = "hisilicon,hi3660-crgctrl", "syscon"; + reg = <0x0 0xfff35000 0x0 0x1000>; + #clock-cells = <1>; + }; + + uart0: serial@fdf02000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x0 0xfdf02000 0x0 0x1000>; + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&crg_ctrl HI3660_CLK_MUX_UART0>, + <&crg_ctrl HI3660_PCLK>; + clock-names = "uartclk", "apb_pclk"; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/clock/idt,versaclock5.txt b/Documentation/devicetree/bindings/clock/idt,versaclock5.txt new file mode 100644 index 000000000000..87e9c47a89a3 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/idt,versaclock5.txt @@ -0,0 +1,65 @@ +Binding for IDT VersaClock5 programmable i2c clock generator. + +The IDT VersaClock5 are programmable i2c clock generators providing +from 3 to 12 output clocks. + +==I2C device node== + +Required properties: +- compatible: shall be one of "idt,5p49v5923" , "idt,5p49v5933". +- reg: i2c device address, shall be 0x68 or 0x6a. +- #clock-cells: from common clock binding; shall be set to 1. +- clocks: from common clock binding; list of parent clock handles, + - 5p49v5923: (required) either or both of XTAL or CLKIN + reference clock. + - 5p49v5933: (optional) property not present (internal + Xtal used) or CLKIN reference + clock. +- clock-names: from common clock binding; clock input names, can be + - 5p49v5923: (required) either or both of "xin", "clkin". + - 5p49v5933: (optional) property not present or "clkin". + +==Mapping between clock specifier and physical pins== + +When referencing the provided clock in the DT using phandle and +clock specifier, the following mapping applies: + +5P49V5923: + 0 -- OUT0_SEL_I2CB + 1 -- OUT1 + 2 -- OUT2 + +5P49V5933: + 0 -- OUT0_SEL_I2CB + 1 -- OUT1 + 2 -- OUT4 + +==Example== + +/* 25MHz reference crystal */ +ref25: ref25m { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; +}; + +i2c-master-node { + + /* IDT 5P49V5923 i2c clock generator */ + vc5: clock-generator@6a { + compatible = "idt,5p49v5923"; + reg = <0x6a>; + #clock-cells = <1>; + + /* Connect XIN input to 25MHz reference */ + clocks = <&ref25m>; + clock-names = "xin"; + }; +}; + +/* Consumer referencing the 5P49V5923 pin OUT1 */ +consumer { + ... + clocks = <&vc5 1>; + ... +} diff --git a/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt index 520562a7dc2a..c7b4e3a6b2c6 100644 --- a/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt +++ b/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt @@ -7,6 +7,7 @@ Required properties: - compatible : must be "marvell,armada-370-corediv-clock", "marvell,armada-375-corediv-clock", "marvell,armada-380-corediv-clock", + "marvell,mv98dx3236-corediv-clock", - reg : must be the register address of Core Divider control register - #clock-cells : from common clock binding; shall be set to 1 diff --git a/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt index 99c214660bdc..7f28506eaee7 100644 --- a/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt +++ b/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt @@ -3,6 +3,7 @@ Device Tree Clock bindings for cpu clock of Marvell EBU platforms Required properties: - compatible : shall be one of the following: "marvell,armada-xp-cpu-clock" - cpu clocks for Armada XP + "marvell,mv98dx3236-cpu-clock" - cpu clocks for 98DX3236 SoC - reg : Address and length of the clock complex register set, followed by address and length of the PMU DFS registers - #clock-cells : should be set to 1. diff --git a/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt b/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt index 87d3714b956a..a7235e9e1c97 100644 --- a/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt @@ -11,6 +11,7 @@ Required properties : compatible "qcom,rpmcc" should be also included. "qcom,rpmcc-msm8916", "qcom,rpmcc" + "qcom,rpmcc-msm8974", "qcom,rpmcc" "qcom,rpmcc-apq8064", "qcom,rpmcc" - #clock-cells : shall contain 1 diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt index c46919412953..f4f944d81308 100644 --- a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt @@ -42,6 +42,10 @@ Required Properties: Domain bindings in Documentation/devicetree/bindings/power/power_domain.txt. + - #reset-cells: Must be 1 + - The single reset specifier cell must be the module number, as defined + in the datasheet. + Examples -------- @@ -55,6 +59,7 @@ Examples clock-names = "extal", "extalr"; #clock-cells = <2>; #power-domain-cells = <0>; + #reset-cells = <1>; }; @@ -69,5 +74,6 @@ Examples dmas = <&dmac1 0x13>, <&dmac1 0x12>; dma-names = "tx", "rx"; power-domains = <&cpg>; + resets = <&cpg 310>; status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt new file mode 100644 index 000000000000..e71c675ba5da --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt @@ -0,0 +1,57 @@ +* Rockchip RK3328 Clock and Reset Unit + +The RK3328 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rk3328-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing pll rates are not changeable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3328-cru.h headers and can be +used in device tree sources. Similar macros exist for the reset sources in +these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "clkin_i2s" - external I2S clock - optional, + - "gmac_clkin" - external GMAC clock - optional + - "phy_50m_out" - output clock of the pll in the mac phy + +Example: Clock controller node: + + cru: clock-controller@ff440000 { + compatible = "rockchip,rk3328-cru"; + reg = <0x0 0xff440000 0x0 0x1000>; + rockchip,grf = <&grf>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@ff120000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff120000 0x100>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&cru SCLK_UART0>; + }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.txt index 3888dd33fcbd..3bc56fae90ac 100644 --- a/Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.txt +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.txt @@ -13,6 +13,12 @@ Required Properties: - #clock-cells: should be 1. - #reset-cells: should be 1. +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files". + It is used for GRF muxes, if missing any muxes present in the GRF will not + be available. + Each clock is assigned an identifier and client nodes can use this identifier to specify the clock which they consume. All available clocks are defined as preprocessor macros in the dt-bindings/clock/rk3399-cru.h headers and can be diff --git a/Documentation/devicetree/bindings/clock/st,stm32-rcc.txt b/Documentation/devicetree/bindings/clock/st,stm32-rcc.txt index 8f19d87cbf24..b240121d2ac9 100644 --- a/Documentation/devicetree/bindings/clock/st,stm32-rcc.txt +++ b/Documentation/devicetree/bindings/clock/st,stm32-rcc.txt @@ -10,6 +10,7 @@ Required properties: - compatible: Should be: "st,stm32f42xx-rcc" "st,stm32f469-rcc" + "st,stm32f746-rcc" - reg: should be register base and length as documented in the datasheet - #reset-cells: 1, see below @@ -84,6 +85,25 @@ The secondary index is bound with the following magic numbers: 12 CLK_I2SQ_PDIV (post divisor of pll i2s q divisor) 13 CLK_SAIQ_PDIV (post divisor of pll sai q divisor) + 14 CLK_HSI (Internal ocscillator clock) + 15 CLK_SYSCLK (System Clock) + 16 CLK_HDMI_CEC (HDMI-CEC clock) + 17 CLK_SPDIF (SPDIF-Rx clock) + 18 CLK_USART1 (U(s)arts clocks) + 19 CLK_USART2 + 20 CLK_USART3 + 21 CLK_UART4 + 22 CLK_UART5 + 23 CLK_USART6 + 24 CLK_UART7 + 25 CLK_UART8 + 26 CLK_I2C1 (I2S clocks) + 27 CLK_I2C2 + 28 CLK_I2C3 + 29 CLK_I2C4 + 30 CLK_LPTIMER (LPTimer1 clock) +) + Example: /* Misc clock, FCLK */ diff --git a/Documentation/devicetree/bindings/clock/stericsson,abx500.txt b/Documentation/devicetree/bindings/clock/stericsson,abx500.txt new file mode 100644 index 000000000000..dbaa886b223e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/stericsson,abx500.txt @@ -0,0 +1,20 @@ +Clock bindings for ST-Ericsson ABx500 clocks + +Required properties : +- compatible : shall contain the following: + "stericsson,ab8500-clk" +- #clock-cells should be <1> + +The ABx500 clocks need to be placed as a subnode of an AB8500 +device node, see mfd/ab8500.txt + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/ste-ab8500.h header and can be used in device +tree sources. + +Example: + +clock-controller { + compatible = "stericsson,ab8500-clk"; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/clock/sun9i-de.txt b/Documentation/devicetree/bindings/clock/sun9i-de.txt new file mode 100644 index 000000000000..fb18f327b97a --- /dev/null +++ b/Documentation/devicetree/bindings/clock/sun9i-de.txt @@ -0,0 +1,28 @@ +Allwinner A80 Display Engine Clock Control Binding +-------------------------------------------------- + +Required properties : +- compatible: must contain one of the following compatibles: + - "allwinner,sun9i-a80-de-clks" + +- reg: Must contain the registers base address and length +- clocks: phandle to the clocks feeding the display engine subsystem. + Three are needed: + - "mod": the display engine module clock + - "dram": the DRAM bus clock for the system + - "bus": the bus clock for the whole display engine subsystem +- clock-names: Must contain the clock names described just above +- resets: phandle to the reset control for the display engine subsystem. +- #clock-cells : must contain 1 +- #reset-cells : must contain 1 + +Example: +de_clocks: clock@3000000 { + compatible = "allwinner,sun9i-a80-de-clks"; + reg = <0x03000000 0x30>; + clocks = <&ccu CLK_DE>, <&ccu CLK_SDRAM>, <&ccu CLK_BUS_DE>; + clock-names = "mod", "dram", "bus"; + resets = <&ccu RST_BUS_DE>; + #clock-cells = <1>; + #reset-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/clock/sun9i-usb.txt b/Documentation/devicetree/bindings/clock/sun9i-usb.txt new file mode 100644 index 000000000000..3564bd4f2a20 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/sun9i-usb.txt @@ -0,0 +1,24 @@ +Allwinner A80 USB Clock Control Binding +--------------------------------------- + +Required properties : +- compatible: must contain one of the following compatibles: + - "allwinner,sun9i-a80-usb-clocks" + +- reg: Must contain the registers base address and length +- clocks: phandle to the clocks feeding the USB subsystem. Two are needed: + - "bus": the bus clock for the whole USB subsystem + - "hosc": the high frequency oscillator (usually at 24MHz) +- clock-names: Must contain the clock names described just above +- #clock-cells : must contain 1 +- #reset-cells : must contain 1 + +Example: +usb_clocks: clock@a08000 { + compatible = "allwinner,sun9i-a80-usb-clks"; + reg = <0x00a08000 0x8>; + clocks = <&ccu CLK_BUS_USB>, <&osc24M>; + clock-names = "bus", "hosc"; + #clock-cells = <1>; + #reset-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt index 74d44a4273f2..bae5668cf427 100644 --- a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt +++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt @@ -7,6 +7,8 @@ Required properties : - "allwinner,sun8i-a23-ccu" - "allwinner,sun8i-a33-ccu" - "allwinner,sun8i-h3-ccu" + - "allwinner,sun8i-v3s-ccu" + - "allwinner,sun9i-a80-ccu" - "allwinner,sun50i-a64-ccu" - reg: Must contain the registers base address and length diff --git a/Documentation/devicetree/bindings/clock/ti,cdce925.txt b/Documentation/devicetree/bindings/clock/ti,cdce925.txt index 4c7669ad681b..0d01f2d5cc36 100644 --- a/Documentation/devicetree/bindings/clock/ti,cdce925.txt +++ b/Documentation/devicetree/bindings/clock/ti,cdce925.txt @@ -1,15 +1,22 @@ -Binding for TO CDCE925 programmable I2C clock synthesizers. +Binding for TI CDCE913/925/937/949 programmable I2C clock synthesizers. Reference This binding uses the common clock binding[1]. [1] Documentation/devicetree/bindings/clock/clock-bindings.txt -[2] http://www.ti.com/product/cdce925 +[2] http://www.ti.com/product/cdce913 +[3] http://www.ti.com/product/cdce925 +[4] http://www.ti.com/product/cdce937 +[5] http://www.ti.com/product/cdce949 The driver provides clock sources for each output Y1 through Y5. Required properties: - - compatible: Shall be "ti,cdce925" + - compatible: Shall be one of the following: + - "ti,cdce913": 1-PLL, 3 Outputs + - "ti,cdce925": 2-PLL, 5 Outputs + - "ti,cdce937": 3-PLL, 7 Outputs + - "ti,cdce949": 4-PLL, 9 Outputs - reg: I2C device address. - clocks: Points to a fixed parent clock that provides the input frequency. - #clock-cells: From common clock bindings: Shall be 1. @@ -18,7 +25,7 @@ Optional properties: - xtal-load-pf: Crystal load-capacitor value to fine-tune performance on a board, or to compensate for external influences. -For both PLL1 and PLL2 an optional child node can be used to specify spread +For all PLL1, PLL2, ... an optional child node can be used to specify spread spectrum clocking parameters for a board. - spread-spectrum: SSC mode as defined in the data sheet. - spread-spectrum-center: Use "centered" mode instead of "max" mode. When diff --git a/Documentation/devicetree/bindings/clock/zx296718-clk.txt b/Documentation/devicetree/bindings/clock/zx296718-clk.txt index 8c18b7b237bf..4ad703808407 100644 --- a/Documentation/devicetree/bindings/clock/zx296718-clk.txt +++ b/Documentation/devicetree/bindings/clock/zx296718-clk.txt @@ -13,6 +13,9 @@ Required properties: "zte,zx296718-lsp1crm": zx296718 device level clock selection and gating + "zte,zx296718-audiocrm": + zx296718 audio clock selection, divider and gating + - reg: Address and length of the register set The clock consumer should specify the desired clock by having the clock diff --git a/Documentation/devicetree/bindings/display/ssd1307fb.txt b/Documentation/devicetree/bindings/display/ssd1307fb.txt index eb31ed47a283..209d931ef16c 100644 --- a/Documentation/devicetree/bindings/display/ssd1307fb.txt +++ b/Documentation/devicetree/bindings/display/ssd1307fb.txt @@ -8,14 +8,15 @@ Required properties: 0x3c or 0x3d - pwm: Should contain the pwm to use according to the OF device tree PWM specification [0]. Only required for the ssd1307. - - reset-gpios: Should contain the GPIO used to reset the OLED display - solomon,height: Height in pixel of the screen driven by the controller - solomon,width: Width in pixel of the screen driven by the controller - solomon,page-offset: Offset of pages (band of 8 pixels) that the screen is mapped to. Optional properties: - - reset-active-low: Is the reset gpio is active on physical low? + - reset-gpios: The GPIO used to reset the OLED display, if available. See + Documentation/devicetree/bindings/gpio/gpio.txt for details. + - vbat-supply: The supply for VBAT - solomon,segment-no-remap: Display needs normal (non-inverted) data column to segment mapping - solomon,com-seq: Display uses sequential COM pin configuration diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt index cf53d5fba20a..aa097045a10e 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt @@ -19,7 +19,14 @@ Optional Properties: - i2c-mux-idle-disconnect: Boolean; if defined, forces mux to disconnect all children in idle state. This is necessary for example, if there are several multiplexers on the bus and the devices behind them use same I2C addresses. - + - interrupt-parent: Phandle for the interrupt controller that services + interrupts for this device. + - interrupts: Interrupt mapping for IRQ. + - interrupt-controller: Marks the device node as an interrupt controller. + - #interrupt-cells : Should be two. + - first cell is the pin number + - second cell is used to specify flags. + See also Documentation/devicetree/bindings/interrupt-controller/interrupts.txt Example: @@ -29,6 +36,11 @@ Example: #size-cells = <0>; reg = <0x74>; + interrupt-parent = <&ipic>; + interrupts = <17 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + i2c@2 { #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt index 7716acc55dec..ae9c2a735f39 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt @@ -10,6 +10,7 @@ Required properties: - "renesas,iic-r8a7793" (R-Car M2-N) - "renesas,iic-r8a7794" (R-Car E2) - "renesas,iic-r8a7795" (R-Car H3) + - "renesas,iic-r8a7796" (R-Car M3-W) - "renesas,iic-sh73a0" (SH-Mobile AG5) - "renesas,rcar-gen2-iic" (generic R-Car Gen2 compatible device) - "renesas,rcar-gen3-iic" (generic R-Car Gen3 compatible device) diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt new file mode 100644 index 000000000000..78eaf7b718ed --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt @@ -0,0 +1,33 @@ +* I2C controller embedded in STMicroelectronics STM32 I2C platform + +Required properties : +- compatible : Must be "st,stm32f4-i2c" +- reg : Offset and length of the register set for the device +- interrupts : Must contain the interrupt id for I2C event and then the + interrupt id for I2C error. +- resets: Must contain the phandle to the reset controller. +- clocks: Must contain the input clock of the I2C instance. +- A pinctrl state named "default" must be defined to set pins in mode of + operation for I2C transfer +- #address-cells = <1>; +- #size-cells = <0>; + +Optional properties : +- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified, + the default 100 kHz frequency will be used. As only Normal and Fast modes + are supported, possible values are 100000 and 400000. + +Example : + + i2c@40005400 { + compatible = "st,stm32f4-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x40005400 0x400>; + interrupts = <31>, + <32>; + resets = <&rcc 277>; + clocks = <&rcc 0 149>; + pinctrl-0 = <&i2c1_sda_pin>, <&i2c1_scl_pin>; + pinctrl-names = "default"; + }; diff --git a/Documentation/devicetree/bindings/i2c/nvidia,tegra186-bpmp-i2c.txt b/Documentation/devicetree/bindings/i2c/nvidia,tegra186-bpmp-i2c.txt new file mode 100644 index 000000000000..ab240e10debc --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/nvidia,tegra186-bpmp-i2c.txt @@ -0,0 +1,42 @@ +NVIDIA Tegra186 BPMP I2C controller + +In Tegra186, the BPMP (Boot and Power Management Processor) owns certain HW +devices, such as the I2C controller for the power management I2C bus. Software +running on other CPUs must perform IPC to the BPMP in order to execute +transactions on that I2C bus. This binding describes an I2C bus that is +accessed in such a fashion. + +The BPMP I2C node must be located directly inside the main BPMP node. See +../firmware/nvidia,tegra186-bpmp.txt for details of the BPMP binding. + +This node represents an I2C controller. See ../i2c/i2c.txt for details of the +core I2C binding. + +Required properties: +- compatible: + Array of strings. + One of: + - "nvidia,tegra186-bpmp-i2c". +- #address-cells: Address cells for I2C device address. + Single-cell integer. + Must be <1>. +- #size-cells: + Single-cell integer. + Must be <0>. +- nvidia,bpmp-bus-id: + Single-cell integer. + Indicates the I2C bus number this DT node represent, as defined by the + BPMP firmware. + +Example: + +bpmp { + ... + + i2c { + compatible = "nvidia,tegra186-bpmp-i2c"; + #address-cells = <1>; + #size-cells = <0>; + nvidia,bpmp-bus-id = <5>; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt index 485bc59fcc48..3c91ad430eea 100644 --- a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt +++ b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt @@ -234,7 +234,7 @@ see regulator.txt - with additional custom properties described below: - qcom,switch-mode-frequency: Usage: required Value type: <u32> - Definition: Frequency (Hz) of the swith mode power supply; + Definition: Frequency (Hz) of the switch mode power supply; must be one of: 19200000, 9600000, 6400000, 4800000, 3840000, 3200000, 2740000, 2400000, 2130000, 1920000, 1750000, 1600000, diff --git a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt index 7aa840c8768d..ae4234ca4ee4 100644 --- a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt +++ b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt @@ -1,7 +1,7 @@ * Marvell Armada 370 / Armada XP / Armada 3700 Ethernet Controller (NETA) Required properties: -- compatible: could be one of the followings +- compatible: could be one of the following: "marvell,armada-370-neta" "marvell,armada-xp-neta" "marvell,armada-3700-neta" diff --git a/Documentation/devicetree/bindings/opp/opp.txt b/Documentation/devicetree/bindings/opp/opp.txt index 9f5ca4457b5f..ecdcfb790704 100644 --- a/Documentation/devicetree/bindings/opp/opp.txt +++ b/Documentation/devicetree/bindings/opp/opp.txt @@ -136,7 +136,7 @@ Optional properties: larger OPP table, based on what version of the hardware we are running on. We still can't have multiple nodes with the same opp-hz value in OPP table. - It's an user defined array containing a hierarchy of hardware version numbers, + It's a user defined array containing a hierarchy of hardware version numbers, supported by the OPP. For example: a platform with hierarchy of three levels of versions (A, B and C), this field should be like <X Y Z>, where X corresponds to Version hierarchy A, Y corresponds to version hierarchy B and Z diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt index 7c85dca4221a..2fd688c8dbdb 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -6,7 +6,7 @@ the first two functions being GPIO in and out. The configuration on the pins includes drive strength and pull-up. Required properties: -- compatible: Should be one of the followings (depending on you SoC): +- compatible: Should be one of the following (depending on your SoC): "allwinner,sun4i-a10-pinctrl" "allwinner,sun5i-a10s-pinctrl" "allwinner,sun5i-a13-pinctrl" diff --git a/Documentation/devicetree/bindings/power/pd-samsung.txt b/Documentation/devicetree/bindings/power/pd-samsung.txt index 7eb9674e9687..549f7dee9b9d 100644 --- a/Documentation/devicetree/bindings/power/pd-samsung.txt +++ b/Documentation/devicetree/bindings/power/pd-samsung.txt @@ -23,7 +23,7 @@ Optional Properties: - clock-names: The following clocks can be specified: - oscclk: Oscillator clock. - clkN: Input clocks to the devices in this power domain. These clocks - will be reparented to oscclk before swithing power domain off. + will be reparented to oscclk before switching power domain off. Their original parent will be brought back after turning on the domain. Maximum of 4 clocks (N = 0 to 3) are supported. - asbN: Clocks required by asynchronous bridges (ASB) present in diff --git a/Documentation/devicetree/bindings/rtc/armada-380-rtc.txt b/Documentation/devicetree/bindings/rtc/armada-380-rtc.txt index 2eb9d4ee7dc0..c3c9a1226f9a 100644 --- a/Documentation/devicetree/bindings/rtc/armada-380-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/armada-380-rtc.txt @@ -1,9 +1,11 @@ -* Real Time Clock of the Armada 38x SoCs +* Real Time Clock of the Armada 38x/7K/8K SoCs -RTC controller for the Armada 38x SoCs +RTC controller for the Armada 38x, 7K and 8K SoCs Required properties: -- compatible : Should be "marvell,armada-380-rtc" +- compatible : Should be one of the following: + "marvell,armada-380-rtc" for Armada 38x SoC + "marvell,armada-8k-rtc" for Aramda 7K/8K SoCs - reg: a list of base address and size pairs, one for each entry in reg-names - reg names: should contain: diff --git a/Documentation/devicetree/bindings/rtc/cortina,gemini.txt b/Documentation/devicetree/bindings/rtc/cortina,gemini.txt new file mode 100644 index 000000000000..4ce4e794ddbb --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/cortina,gemini.txt @@ -0,0 +1,14 @@ +* Cortina Systems Gemini RTC + +Gemini SoC real-time clock. + +Required properties: +- compatible : Should be "cortina,gemini-rtc" + +Examples: + +rtc@45000000 { + compatible = "cortina,gemini-rtc"; + reg = <0x45000000 0x100>; + interrupts = <17 IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/rtc/imxdi-rtc.txt b/Documentation/devicetree/bindings/rtc/imxdi-rtc.txt index c9d80d7da141..323cf26374cb 100644 --- a/Documentation/devicetree/bindings/rtc/imxdi-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/imxdi-rtc.txt @@ -8,10 +8,13 @@ Required properties: region. - interrupts: rtc alarm interrupt +Optional properties: +- interrupts: dryice security violation interrupt + Example: rtc@80056000 { compatible = "fsl,imx53-rtc", "fsl,imx25-rtc"; reg = <0x80056000 2000>; - interrupts = <29>; + interrupts = <29 56>; }; diff --git a/Documentation/devicetree/bindings/rtc/maxim,ds3231.txt b/Documentation/devicetree/bindings/rtc/maxim,ds3231.txt index 1ad4c1c2b3b3..85be53a42180 100644 --- a/Documentation/devicetree/bindings/rtc/maxim,ds3231.txt +++ b/Documentation/devicetree/bindings/rtc/maxim,ds3231.txt @@ -1,7 +1,8 @@ * Maxim DS3231 Real Time Clock Required properties: -see: Documentation/devicetree/bindings/i2c/trivial-admin-guide/devices.rst +- compatible: Should contain "maxim,ds3231". +- reg: I2C address for chip. Optional property: - #clock-cells: Should be 1. diff --git a/Documentation/devicetree/bindings/rtc/pcf8563.txt b/Documentation/devicetree/bindings/rtc/pcf8563.txt index 086c998c5561..36984acbb383 100644 --- a/Documentation/devicetree/bindings/rtc/pcf8563.txt +++ b/Documentation/devicetree/bindings/rtc/pcf8563.txt @@ -3,7 +3,8 @@ Philips PCF8563/Epson RTC8564 Real Time Clock Required properties: -see: Documentation/devicetree/bindings/i2c/trivial-admin-guide/devices.rst +- compatible: Should contain "nxp,pcf8563". +- reg: I2C address for chip. Optional property: - #clock-cells: Should be 0. diff --git a/Documentation/devicetree/bindings/rtc/st,stm32-rtc.txt b/Documentation/devicetree/bindings/rtc/st,stm32-rtc.txt new file mode 100644 index 000000000000..e2837b951237 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/st,stm32-rtc.txt @@ -0,0 +1,27 @@ +STM32 Real Time Clock + +Required properties: +- compatible: "st,stm32-rtc". +- reg: address range of rtc register set. +- clocks: reference to the clock entry ck_rtc. +- interrupt-parent: phandle for the interrupt controller. +- interrupts: rtc alarm interrupt. +- st,syscfg: phandle for pwrcfg, mandatory to disable/enable backup domain + (RTC registers) write protection. + +Optional properties (to override default ck_rtc parent clock): +- assigned-clocks: reference to the ck_rtc clock entry. +- assigned-clock-parents: phandle of the new parent clock of ck_rtc. + +Example: + + rtc: rtc@40002800 { + compatible = "st,stm32-rtc"; + reg = <0x40002800 0x400>; + clocks = <&rcc 1 CLK_RTC>; + assigned-clocks = <&rcc 1 CLK_RTC>; + assigned-clock-parents = <&rcc 1 CLK_LSE>; + interrupt-parent = <&exti>; + interrupts = <17 1>; + st,syscfg = <&pwrcfg>; + }; diff --git a/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt b/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt index f007e428a1ab..945934918b71 100644 --- a/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt @@ -8,10 +8,20 @@ Required properties: memory mapped region. - interrupts : IRQ lines for the RTC alarm 0 and alarm 1, in that order. +Required properties for new device trees +- clocks : phandle to the 32kHz external oscillator +- clock-output-names : name of the LOSC clock created +- #clock-cells : must be equals to 1. The RTC provides two clocks: the + LOSC and its external output, with index 0 and 1 + respectively. + Example: rtc: rtc@01f00000 { compatible = "allwinner,sun6i-a31-rtc"; reg = <0x01f00000 0x54>; interrupts = <0 40 4>, <0 41 4>; + clock-output-names = "osc32k"; + clocks = <&ext_osc32k>; + #clock-cells = <1>; }; diff --git a/Documentation/devicetree/bindings/soc/rockchip/grf.txt b/Documentation/devicetree/bindings/soc/rockchip/grf.txt index c6e62cb30712..a0685c209218 100644 --- a/Documentation/devicetree/bindings/soc/rockchip/grf.txt +++ b/Documentation/devicetree/bindings/soc/rockchip/grf.txt @@ -10,7 +10,7 @@ From RK3368 SoCs, the GRF is divided into two sections, Required Properties: -- compatible: GRF should be one of the followings +- compatible: GRF should be one of the following: - "rockchip,rk3036-grf", "syscon": for rk3036 - "rockchip,rk3066-grf", "syscon": for rk3066 - "rockchip,rk3188-grf", "syscon": for rk3188 @@ -18,7 +18,7 @@ Required Properties: - "rockchip,rk3288-grf", "syscon": for rk3288 - "rockchip,rk3368-grf", "syscon": for rk3368 - "rockchip,rk3399-grf", "syscon": for rk3399 -- compatible: PMUGRF should be one of the followings +- compatible: PMUGRF should be one of the following: - "rockchip,rk3368-pmugrf", "syscon": for rk3368 - "rockchip,rk3399-pmugrf", "syscon": for rk3399 - compatible: SGRF should be one of the following diff --git a/Documentation/devicetree/bindings/sound/rockchip-i2s.txt b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt index 4ea29aa9af59..a6600f6dea64 100644 --- a/Documentation/devicetree/bindings/sound/rockchip-i2s.txt +++ b/Documentation/devicetree/bindings/sound/rockchip-i2s.txt @@ -5,7 +5,7 @@ audio data transfer between devices in the system. Required properties: -- compatible: should be one of the followings +- compatible: should be one of the following: - "rockchip,rk3066-i2s": for rk3066 - "rockchip,rk3188-i2s", "rockchip,rk3066-i2s": for rk3188 - "rockchip,rk3288-i2s", "rockchip,rk3066-i2s": for rk3288 @@ -17,7 +17,7 @@ Required properties: Documentation/devicetree/bindings/dma/dma.txt - dma-names: should include "tx" and "rx". - clocks: a list of phandle + clock-specifer pairs, one for each entry in clock-names. -- clock-names: should contain followings: +- clock-names: should contain the following: - "i2s_hclk": clock for I2S BUS - "i2s_clk" : clock for I2S controller - rockchip,playback-channels: max playback channels, if not set, 8 channels default. diff --git a/Documentation/devicetree/bindings/sound/rt5665.txt b/Documentation/devicetree/bindings/sound/rt5665.txt index 419c89219681..419c89219681 100755..100644 --- a/Documentation/devicetree/bindings/sound/rt5665.txt +++ b/Documentation/devicetree/bindings/sound/rt5665.txt diff --git a/Documentation/devicetree/bindings/sound/sun4i-codec.txt b/Documentation/devicetree/bindings/sound/sun4i-codec.txt index 3033bd8aab0f..3863531d1e6d 100644 --- a/Documentation/devicetree/bindings/sound/sun4i-codec.txt +++ b/Documentation/devicetree/bindings/sound/sun4i-codec.txt @@ -14,7 +14,7 @@ Required properties: - dma-names: should include "tx" and "rx". - clocks: a list of phandle + clock-specifer pairs, one for each entry in clock-names. -- clock-names: should contain followings: +- clock-names: should contain the following: - "apb": the parent APB clock for this controller - "codec": the parent module clock diff --git a/Documentation/devicetree/bindings/sound/sun4i-i2s.txt b/Documentation/devicetree/bindings/sound/sun4i-i2s.txt index f4adc58f82ba..ee21da865771 100644 --- a/Documentation/devicetree/bindings/sound/sun4i-i2s.txt +++ b/Documentation/devicetree/bindings/sound/sun4i-i2s.txt @@ -5,7 +5,7 @@ audio data transfer between devices in the system. Required properties: -- compatible: should be one of the followings +- compatible: should be one of the following: - "allwinner,sun4i-a10-i2s" - "allwinner,sun6i-a31-i2s" - reg: physical base address of the controller and length of memory mapped @@ -15,7 +15,7 @@ Required properties: Documentation/devicetree/bindings/dma/dma.txt - dma-names: should include "tx" and "rx". - clocks: a list of phandle + clock-specifer pairs, one for each entry in clock-names. -- clock-names: should contain followings: +- clock-names: should contain the following: - "apb" : clock for the I2S bus interface - "mod" : module clock for the I2S controller - #sound-dai-cells : Must be equal to 0 diff --git a/Documentation/devicetree/bindings/watchdog/cortina,gemin-watchdog.txt b/Documentation/devicetree/bindings/watchdog/cortina,gemin-watchdog.txt new file mode 100644 index 000000000000..bc4b865d178b --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/cortina,gemin-watchdog.txt @@ -0,0 +1,17 @@ +Cortina Systems Gemini SoC Watchdog + +Required properties: +- compatible : must be "cortina,gemini-watchdog" +- reg : shall contain base register location and length +- interrupts : shall contain the interrupt for the watchdog + +Optional properties: +- timeout-sec : the default watchdog timeout in seconds. + +Example: + +watchdog@41000000 { + compatible = "cortina,gemini-watchdog"; + reg = <0x41000000 0x1000>; + interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt index 8f3d96af81d7..1f6e101e299a 100644 --- a/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt @@ -6,10 +6,11 @@ occurred. Required properties: - compatible : should be one among the following - (a) "samsung,s3c2410-wdt" for Exynos4 and previous SoCs - (b) "samsung,exynos5250-wdt" for Exynos5250 - (c) "samsung,exynos5420-wdt" for Exynos5420 - (c) "samsung,exynos7-wdt" for Exynos7 + - "samsung,s3c2410-wdt" for S3C2410 + - "samsung,s3c6410-wdt" for S3C6410, S5PV210 and Exynos4 + - "samsung,exynos5250-wdt" for Exynos5250 + - "samsung,exynos5420-wdt" for Exynos5420 + - "samsung,exynos7-wdt" for Exynos7 - reg : base physical address of the controller and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt b/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt new file mode 100644 index 000000000000..06ce67766756 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt @@ -0,0 +1,32 @@ +ZTE zx2967 Watchdog timer + +Required properties: + +- compatible : should be one of the following. + * zte,zx296718-wdt +- reg : Specifies base physical address and size of the registers. +- clocks : Pairs of phandle and specifier referencing the controller's clocks. +- resets : Reference to the reset controller controlling the watchdog + controller. + +Optional properties: + +- timeout-sec : Contains the watchdog timeout in seconds. +- zte,wdt-reset-sysctrl : Directs how to reset system by the watchdog. + if we don't want to restart system when watchdog been triggered, + it's not required, vice versa. + It should include following fields. + * phandle of aon-sysctrl. + * offset of register that be written, should be 0xb0. + * configure value that be written to aon-sysctrl. + * bit mask, corresponding bits will be affected. + +Example: + +wdt: watchdog@1465000 { + compatible = "zte,zx296718-wdt"; + reg = <0x1465000 0x1000>; + clocks = <&topcrm WDT_WCLK>; + resets = <&toprst 35>; + zte,wdt-reset-sysctrl = <&aon_sysctrl 0xb0 1 0x115>; +}; |