diff options
Diffstat (limited to 'Documentation/hwmon')
| -rw-r--r-- | Documentation/hwmon/sysfs-interface | 181 |
1 files changed, 107 insertions, 74 deletions
diff --git a/Documentation/hwmon/sysfs-interface b/Documentation/hwmon/sysfs-interface index eeb912254db4..bc59a5113d17 100644 --- a/Documentation/hwmon/sysfs-interface +++ b/Documentation/hwmon/sysfs-interface @@ -69,28 +69,37 @@ to cause an alarm) is chip-dependent. ------------------------------------------------------------------------- +[0-*] denotes any positive number starting from 0 +[1-*] denotes any positive number starting from 1 +RO read only value +RW read/write value + +Read/write values may be read-only for some chips, depending on the +hardware implementation. + ************ * Voltages * ************ -in[0-8]_min Voltage min value. +in[0-*]_min Voltage min value. Unit: millivolt - Read/Write + RW -in[0-8]_max Voltage max value. +in[0-*]_max Voltage max value. Unit: millivolt - Read/Write + RW -in[0-8]_input Voltage input value. +in[0-*]_input Voltage input value. Unit: millivolt - Read only + RO + Voltage measured on the chip pin. Actual voltage depends on the scaling resistors on the motherboard, as recommended in the chip datasheet. This varies by chip and by motherboard. Because of this variation, values are generally NOT scaled by the chip driver, and must be done by the application. However, some drivers (notably lm87 and via686a) - do scale, with various degrees of success. + do scale, because of internal resistors built into a chip. These drivers will output the actual voltage. Typical usage: @@ -104,58 +113,72 @@ in[0-8]_input Voltage input value. in7_* varies in8_* varies -cpu[0-1]_vid CPU core reference voltage. +cpu[0-*]_vid CPU core reference voltage. Unit: millivolt - Read only. + RO Not always correct. vrm Voltage Regulator Module version number. - Read only. - Two digit number, first is major version, second is - minor version. + RW (but changing it should no more be necessary) + Originally the VRM standard version multiplied by 10, but now + an arbitrary number, as not all standards have a version + number. Affects the way the driver calculates the CPU core reference voltage from the vid pins. +Also see the Alarms section for status flags associated with voltages. + ******** * Fans * ******** -fan[1-3]_min Fan minimum value +fan[1-*]_min Fan minimum value Unit: revolution/min (RPM) - Read/Write. + RW -fan[1-3]_input Fan input value. +fan[1-*]_input Fan input value. Unit: revolution/min (RPM) - Read only. + RO -fan[1-3]_div Fan divisor. +fan[1-*]_div Fan divisor. Integer value in powers of two (1, 2, 4, 8, 16, 32, 64, 128). + RW Some chips only support values 1, 2, 4 and 8. Note that this is actually an internal clock divisor, which affects the measurable speed range, not the read value. +Also see the Alarms section for status flags associated with fans. + + ******* * PWM * ******* -pwm[1-3] Pulse width modulation fan control. +pwm[1-*] Pulse width modulation fan control. Integer value in the range 0 to 255 - Read/Write + RW 255 is max or 100%. -pwm[1-3]_enable +pwm[1-*]_enable Switch PWM on and off. Not always present even if fan*_pwm is. - 0 to turn off - 1 to turn on in manual mode - 2 to turn on in automatic mode - Read/Write + 0: turn off + 1: turn on in manual mode + 2+: turn on in automatic mode + Check individual chip documentation files for automatic mode details. + RW + +pwm[1-*]_mode + 0: DC mode + 1: PWM mode + RW pwm[1-*]_auto_channels_temp Select which temperature channels affect this PWM output in auto mode. Bitfield, 1 is temp1, 2 is temp2, 4 is temp3 etc... Which values are possible depend on the chip used. + RW pwm[1-*]_auto_point[1-*]_pwm pwm[1-*]_auto_point[1-*]_temp @@ -163,6 +186,7 @@ pwm[1-*]_auto_point[1-*]_temp_hyst Define the PWM vs temperature curve. Number of trip points is chip-dependent. Use this for chips which associate trip points to PWM output channels. + RW OR @@ -172,51 +196,52 @@ temp[1-*]_auto_point[1-*]_temp_hyst Define the PWM vs temperature curve. Number of trip points is chip-dependent. Use this for chips which associate trip points to temperature channels. + RW **************** * Temperatures * **************** -temp[1-3]_type Sensor type selection. +temp[1-*]_type Sensor type selection. Integers 1 to 4 or thermistor Beta value (typically 3435) - Read/Write. + RW 1: PII/Celeron Diode 2: 3904 transistor 3: thermal diode 4: thermistor (default/unknown Beta) Not all types are supported by all chips -temp[1-4]_max Temperature max value. +temp[1-*]_max Temperature max value. Unit: millidegree Celcius - Read/Write value. + RW -temp[1-3]_min Temperature min value. +temp[1-*]_min Temperature min value. Unit: millidegree Celcius - Read/Write value. + RW -temp[1-3]_max_hyst +temp[1-*]_max_hyst Temperature hysteresis value for max limit. Unit: millidegree Celcius Must be reported as an absolute temperature, NOT a delta from the max value. - Read/Write value. + RW -temp[1-4]_input Temperature input value. +temp[1-*]_input Temperature input value. Unit: millidegree Celcius - Read only value. + RO -temp[1-4]_crit Temperature critical value, typically greater than +temp[1-*]_crit Temperature critical value, typically greater than corresponding temp_max values. Unit: millidegree Celcius - Read/Write value. + RW -temp[1-2]_crit_hyst +temp[1-*]_crit_hyst Temperature hysteresis value for critical limit. Unit: millidegree Celcius Must be reported as an absolute temperature, NOT a delta from the critical value. - Read/Write value. + RW temp[1-4]_offset Temperature offset which is added to the temperature reading @@ -231,6 +256,8 @@ temp[1-4]_offset itself, for example the thermal diode inside the CPU or a thermistor nearby. +Also see the Alarms section for status flags associated with temperatures. + ************ * Currents * @@ -239,17 +266,17 @@ temp[1-4]_offset Note that no known chip provides current measurements as of writing, so this part is theoretical, so to say. -curr[1-n]_max Current max value +curr[1-*]_max Current max value Unit: milliampere - Read/Write. + RW -curr[1-n]_min Current min value. +curr[1-*]_min Current min value. Unit: milliampere - Read/Write. + RW -curr[1-n]_input Current input value +curr[1-*]_input Current input value Unit: milliampere - Read only. + RO ********** @@ -263,50 +290,54 @@ Usually a given chip will either use channel-related alarms, or limit-related alarms, not both. The driver should just reflect the hardware implementation. -in[0-n]_alarm -fan[1-n]_alarm -temp[1-n]_alarm +in[0-*]_alarm +fan[1-*]_alarm +temp[1-*]_alarm Channel alarm - Boolean - Read-only + 0: no alarm + 1: alarm + RO OR -in[0-n]_min_alarm -in[0-n]_max_alarm -fan[1-n]_min_alarm -temp[1-n]_min_alarm -temp[1-n]_max_alarm -temp[1-n]_crit_alarm +in[0-*]_min_alarm +in[0-*]_max_alarm +fan[1-*]_min_alarm +temp[1-*]_min_alarm +temp[1-*]_max_alarm +temp[1-*]_crit_alarm Limit alarm - Boolean - Read-only + 0: no alarm + 1: alarm + RO Each input channel may have an associated fault file. This can be used to notify open diodes, unconnected fans etc. where the hardware supports it. When this boolean has value 1, the measurement for that channel should not be trusted. -in[0-n]_input_fault -fan[1-n]_input_fault -temp[1-n]_input_fault +in[0-*]_input_fault +fan[1-*]_input_fault +temp[1-*]_input_fault Input fault condition - Boolean - Read-only + 0: no fault occured + 1: fault condition + RO Some chips also offer the possibility to get beeped when an alarm occurs: beep_enable Master beep enable - Boolean - Read/Write + 0: no beeps + 1: beeps + RW -in[0-n]_beep -fan[1-n]_beep -temp[1-n]_beep +in[0-*]_beep +fan[1-*]_beep +temp[1-*]_beep Channel beep - 0 to disable. - 1 to enable. - Read/write + 0: disable + 1: enable + RW In theory, a chip could provide per-limit beep masking, but no such chip was seen so far. @@ -316,7 +347,7 @@ beeps. These interface files are deprecated, but will be kept around for compatibility reasons: alarms Alarm bitmask. - Read only. + RO Integer representation of one to four bytes. A '1' bit means an alarm. Chips should be programmed for 'comparator' mode so that @@ -333,7 +364,7 @@ beep_mask Bitmask for beep. Same format as 'alarms' with the same bit locations, use discouraged for the same reason. Use individual *_beep files instead. - Read/Write + RW ********* @@ -341,7 +372,9 @@ beep_mask Bitmask for beep. ********* eeprom Raw EEPROM data in binary form. - Read only. + RO pec Enable or disable PEC (SMBus only) - Read/Write + 0: disable + 1: enable + RW |