diff options
Diffstat (limited to 'Documentation/powerpc/booting-without-of.txt')
| -rw-r--r-- | Documentation/powerpc/booting-without-of.txt | 65 |
1 files changed, 61 insertions, 4 deletions
diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt index ea1b70b35793..928a79ceb7aa 100644 --- a/Documentation/powerpc/booting-without-of.txt +++ b/Documentation/powerpc/booting-without-of.txt @@ -59,6 +59,7 @@ Table of Contents p) Freescale Synchronous Serial Interface q) USB EHCI controllers r) MDIO on GPIOs + s) SPI busses VII - Marvell Discovery mv64[345]6x System Controller chips 1) The /system-controller node @@ -707,7 +708,7 @@ device or bus to be described by the device tree. In general, the format of an address for a device is defined by the parent bus type, based on the #address-cells and #size-cells properties. Note that the parent's parent definitions of #address-cells -and #size-cells are not inhereted so every node with children must specify +and #size-cells are not inherited so every node with children must specify them. The kernel requires the root node to have those properties defining addresses format for devices directly mapped on the processor bus. @@ -1776,7 +1777,7 @@ platforms are moved over to use the flattened-device-tree model. Xilinx uartlite devices are simple fixed speed serial ports. - Requred properties: + Required properties: - current-speed : Baud rate of uartlite v) Xilinx hwicap @@ -1798,7 +1799,7 @@ platforms are moved over to use the flattened-device-tree model. Xilinx UART 16550 devices are very similar to the NS16550 but with different register spacing and an offset from the base address. - Requred properties: + Required properties: - clock-frequency : Frequency of the clock input - reg-offset : A value of 3 is required - reg-shift : A value of 2 is required @@ -1883,6 +1884,62 @@ platforms are moved over to use the flattened-device-tree model. &qe_pio_c 6>; }; + s) SPI (Serial Peripheral Interface) busses + + SPI busses can be described with a node for the SPI master device + and a set of child nodes for each SPI slave on the bus. For this + discussion, it is assumed that the system's SPI controller is in + SPI master mode. This binding does not describe SPI controllers + in slave mode. + + The SPI master node requires the following properties: + - #address-cells - number of cells required to define a chip select + address on the SPI bus. + - #size-cells - should be zero. + - compatible - name of SPI bus controller following generic names + recommended practice. + No other properties are required in the SPI bus node. It is assumed + that a driver for an SPI bus device will understand that it is an SPI bus. + However, the binding does not attempt to define the specific method for + assigning chip select numbers. Since SPI chip select configuration is + flexible and non-standardized, it is left out of this binding with the + assumption that board specific platform code will be used to manage + chip selects. Individual drivers can define additional properties to + support describing the chip select layout. + + SPI slave nodes must be children of the SPI master node and can + contain the following properties. + - reg - (required) chip select address of device. + - compatible - (required) name of SPI device following generic names + recommended practice + - spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz + - spi-cpol - (optional) Empty property indicating device requires + inverse clock polarity (CPOL) mode + - spi-cpha - (optional) Empty property indicating device requires + shifted clock phase (CPHA) mode + + SPI example for an MPC5200 SPI bus: + spi@f00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; + reg = <0xf00 0x20>; + interrupts = <2 13 0 2 14 0>; + interrupt-parent = <&mpc5200_pic>; + + ethernet-switch@0 { + compatible = "micrel,ks8995m"; + spi-max-frequency = <1000000>; + reg = <0>; + }; + + codec@1 { + compatible = "ti,tlv320aic26"; + spi-max-frequency = <100000>; + reg = <1>; + }; + }; + VII - Marvell Discovery mv64[345]6x System Controller chips =========================================================== @@ -1896,7 +1953,7 @@ prefixed with the string "marvell,", for Marvell Technology Group Ltd. 1) The /system-controller node This node is used to represent the system-controller and must be - present when the system uses a system contller chip. The top-level + present when the system uses a system controller chip. The top-level system-controller node contains information that is global to all devices within the system controller chip. The node name begins with "system-controller" followed by the unit address, which is |