summaryrefslogtreecommitdiff
path: root/Documentation/remoteproc.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/remoteproc.txt')
-rw-r--r--Documentation/remoteproc.txt324
1 files changed, 324 insertions, 0 deletions
diff --git a/Documentation/remoteproc.txt b/Documentation/remoteproc.txt
new file mode 100644
index 000000000000..23ff7349ffe7
--- /dev/null
+++ b/Documentation/remoteproc.txt
@@ -0,0 +1,324 @@
+Remote Processor Framework
+
+1. Introduction
+
+Modern SoCs typically have heterogeneous remote processor devices in asymmetric
+multiprocessing (AMP) configurations, which may be running different instances
+of operating system, whether it's Linux or any other flavor of real-time OS.
+
+OMAP4, for example, has dual Cortex-A9, dual Cortex-M3 and a C64x+ DSP.
+In a typical configuration, the dual cortex-A9 is running Linux in a SMP
+configuration, and each of the other three cores (two M3 cores and a DSP)
+is running its own instance of RTOS in an AMP configuration.
+
+The remoteproc framework allows different platforms/architectures to
+control (power on, load firmware, power off) those remote processors while
+abstracting the hardware differences, so the entire driver doesn't need to be
+duplicated. In addition, this framework also adds rpmsg virtio devices
+for remote processors that supports this kind of communication. This way,
+platform-specific remoteproc drivers only need to provide a few low-level
+handlers, and then all rpmsg drivers will then just work
+(for more information about the virtio-based rpmsg bus and its drivers,
+please read Documentation/rpmsg.txt).
+
+2. User API
+
+ int rproc_boot(struct rproc *rproc)
+ - Boot a remote processor (i.e. load its firmware, power it on, ...).
+ If the remote processor is already powered on, this function immediately
+ returns (successfully).
+ Returns 0 on success, and an appropriate error value otherwise.
+ Note: to use this function you should already have a valid rproc
+ handle. There are several ways to achieve that cleanly (devres, pdata,
+ the way remoteproc_rpmsg.c does this, or, if this becomes prevalent, we
+ might also consider using dev_archdata for this). See also
+ rproc_get_by_name() below.
+
+ void rproc_shutdown(struct rproc *rproc)
+ - Power off a remote processor (previously booted with rproc_boot()).
+ In case @rproc is still being used by an additional user(s), then
+ this function will just decrement the power refcount and exit,
+ without really powering off the device.
+ Every call to rproc_boot() must (eventually) be accompanied by a call
+ to rproc_shutdown(). Calling rproc_shutdown() redundantly is a bug.
+ Notes:
+ - we're not decrementing the rproc's refcount, only the power refcount.
+ which means that the @rproc handle stays valid even after
+ rproc_shutdown() returns, and users can still use it with a subsequent
+ rproc_boot(), if needed.
+ - don't call rproc_shutdown() to unroll rproc_get_by_name(), exactly
+ because rproc_shutdown() _does not_ decrement the refcount of @rproc.
+ To decrement the refcount of @rproc, use rproc_put() (but _only_ if
+ you acquired @rproc using rproc_get_by_name()).
+
+ struct rproc *rproc_get_by_name(const char *name)
+ - Find an rproc handle using the remote processor's name, and then
+ boot it. If it's already powered on, then just immediately return
+ (successfully). Returns the rproc handle on success, and NULL on failure.
+ This function increments the remote processor's refcount, so always
+ use rproc_put() to decrement it back once rproc isn't needed anymore.
+ Note: currently rproc_get_by_name() and rproc_put() are not used anymore
+ by the rpmsg bus and its drivers. We need to scrutinize the use cases
+ that still need them, and see if we can migrate them to use the non
+ name-based boot/shutdown interface.
+
+ void rproc_put(struct rproc *rproc)
+ - Decrement @rproc's power refcount and shut it down if it reaches zero
+ (essentially by just calling rproc_shutdown), and then decrement @rproc's
+ validity refcount too.
+ After this function returns, @rproc may _not_ be used anymore, and its
+ handle should be considered invalid.
+ This function should be called _iff_ the @rproc handle was grabbed by
+ calling rproc_get_by_name().
+
+3. Typical usage
+
+#include <linux/remoteproc.h>
+
+/* in case we were given a valid 'rproc' handle */
+int dummy_rproc_example(struct rproc *my_rproc)
+{
+ int ret;
+
+ /* let's power on and boot our remote processor */
+ ret = rproc_boot(my_rproc);
+ if (ret) {
+ /*
+ * something went wrong. handle it and leave.
+ */
+ }
+
+ /*
+ * our remote processor is now powered on... give it some work
+ */
+
+ /* let's shut it down now */
+ rproc_shutdown(my_rproc);
+}
+
+4. API for implementors
+
+ struct rproc *rproc_alloc(struct device *dev, const char *name,
+ const struct rproc_ops *ops,
+ const char *firmware, int len)
+ - Allocate a new remote processor handle, but don't register
+ it yet. Required parameters are the underlying device, the
+ name of this remote processor, platform-specific ops handlers,
+ the name of the firmware to boot this rproc with, and the
+ length of private data needed by the allocating rproc driver (in bytes).
+
+ This function should be used by rproc implementations during
+ initialization of the remote processor.
+ After creating an rproc handle using this function, and when ready,
+ implementations should then call rproc_register() to complete
+ the registration of the remote processor.
+ On success, the new rproc is returned, and on failure, NULL.
+
+ Note: _never_ directly deallocate @rproc, even if it was not registered
+ yet. Instead, if you just need to unroll rproc_alloc(), use rproc_free().
+
+ void rproc_free(struct rproc *rproc)
+ - Free an rproc handle that was allocated by rproc_alloc.
+ This function should _only_ be used if @rproc was only allocated,
+ but not registered yet.
+ If @rproc was already successfully registered (by calling
+ rproc_register()), then use rproc_unregister() instead.
+
+ int rproc_register(struct rproc *rproc)
+ - Register @rproc with the remoteproc framework, after it has been
+ allocated with rproc_alloc().
+ This is called by the platform-specific rproc implementation, whenever
+ a new remote processor device is probed.
+ Returns 0 on success and an appropriate error code otherwise.
+ Note: this function initiates an asynchronous firmware loading
+ context, which will look for virtio devices supported by the rproc's
+ firmware.
+ If found, those virtio devices will be created and added, so as a result
+ of registering this remote processor, additional virtio drivers might get
+ probed.
+ Currently, though, we only support a single RPMSG virtio vdev per remote
+ processor.
+
+ int rproc_unregister(struct rproc *rproc)
+ - Unregister a remote processor, and decrement its refcount.
+ If its refcount drops to zero, then @rproc will be freed. If not,
+ it will be freed later once the last reference is dropped.
+
+ This function should be called when the platform specific rproc
+ implementation decides to remove the rproc device. it should
+ _only_ be called if a previous invocation of rproc_register()
+ has completed successfully.
+
+ After rproc_unregister() returns, @rproc is _not_ valid anymore and
+ it shouldn't be used. More specifically, don't call rproc_free()
+ or try to directly free @rproc after rproc_unregister() returns;
+ none of these are needed, and calling them is a bug.
+
+ Returns 0 on success and -EINVAL if @rproc isn't valid.
+
+5. Implementation callbacks
+
+These callbacks should be provided by platform-specific remoteproc
+drivers:
+
+/**
+ * struct rproc_ops - platform-specific device handlers
+ * @start: power on the device and boot it
+ * @stop: power off the device
+ * @kick: kick a virtqueue (virtqueue id given as a parameter)
+ */
+struct rproc_ops {
+ int (*start)(struct rproc *rproc);
+ int (*stop)(struct rproc *rproc);
+ void (*kick)(struct rproc *rproc, int vqid);
+};
+
+Every remoteproc implementation should at least provide the ->start and ->stop
+handlers. If rpmsg functionality is also desired, then the ->kick handler
+should be provided as well.
+
+The ->start() handler takes an rproc handle and should then power on the
+device and boot it (use rproc->priv to access platform-specific private data).
+The boot address, in case needed, can be found in rproc->bootaddr (remoteproc
+core puts there the ELF entry point).
+On success, 0 should be returned, and on failure, an appropriate error code.
+
+The ->stop() handler takes an rproc handle and powers the device down.
+On success, 0 is returned, and on failure, an appropriate error code.
+
+The ->kick() handler takes an rproc handle, and an index of a virtqueue
+where new message was placed in. Implementations should interrupt the remote
+processor and let it know it has pending messages. Notifying remote processors
+the exact virtqueue index to look in is optional: it is easy (and not
+too expensive) to go through the existing virtqueues and look for new buffers
+in the used rings.
+
+6. Binary Firmware Structure
+
+At this point remoteproc only supports ELF32 firmware binaries. However,
+it is quite expected that other platforms/devices which we'd want to
+support with this framework will be based on different binary formats.
+
+When those use cases show up, we will have to decouple the binary format
+from the framework core, so we can support several binary formats without
+duplicating common code.
+
+When the firmware is parsed, its various segments are loaded to memory
+according to the specified device address (might be a physical address
+if the remote processor is accessing memory directly).
+
+In addition to the standard ELF segments, most remote processors would
+also include a special section which we call "the resource table".
+
+The resource table contains system resources that the remote processor
+requires before it should be powered on, such as allocation of physically
+contiguous memory, or iommu mapping of certain on-chip peripherals.
+Remotecore will only power up the device after all the resource table's
+requirement are met.
+
+In addition to system resources, the resource table may also contain
+resource entries that publish the existence of supported features
+or configurations by the remote processor, such as trace buffers and
+supported virtio devices (and their configurations).
+
+Currently the resource table is just an array of:
+
+/**
+ * struct fw_resource - describes an entry from the resource section
+ * @type: resource type
+ * @id: index number of the resource
+ * @da: device address of the resource
+ * @pa: physical address of the resource
+ * @len: size, in bytes, of the resource
+ * @flags: properties of the resource, e.g. iommu protection required
+ * @reserved: must be 0 atm
+ * @name: name of resource
+ */
+struct fw_resource {
+ u32 type;
+ u32 id;
+ u64 da;
+ u64 pa;
+ u32 len;
+ u32 flags;
+ u8 reserved[16];
+ u8 name[48];
+} __packed;
+
+Some resources entries are mere announcements, where the host is informed
+of specific remoteproc configuration. Other entries require the host to
+do something (e.g. reserve a requested resource) and possibly also reply
+by overwriting a member inside 'struct fw_resource' with info about the
+allocated resource.
+
+Different resource entries use different members of this struct,
+with different meanings. This is pretty limiting and error-prone,
+so the plan is to move to variable-length TLV-based resource entries,
+where each resource will begin with a type and length fields, followed by
+its own specific structure.
+
+Here are the resource types that are currently being used:
+
+/**
+ * enum fw_resource_type - types of resource entries
+ *
+ * @RSC_CARVEOUT: request for allocation of a physically contiguous
+ * memory region.
+ * @RSC_DEVMEM: request to iommu_map a memory-based peripheral.
+ * @RSC_TRACE: announces the availability of a trace buffer into which
+ * the remote processor will be writing logs. In this case,
+ * 'da' indicates the device address where logs are written to,
+ * and 'len' is the size of the trace buffer.
+ * @RSC_VRING: request for allocation of a virtio vring (address should
+ * be indicated in 'da', and 'len' should contain the number
+ * of buffers supported by the vring).
+ * @RSC_VIRTIO_DEV: announces support for a virtio device, and serves as
+ * the virtio header. 'da' contains the virtio device
+ * features, 'pa' holds the virtio guest features (host
+ * will write them here after they're negotiated), 'len'
+ * holds the virtio status, and 'flags' holds the virtio
+ * device id (currently only VIRTIO_ID_RPMSG is supported).
+ */
+enum fw_resource_type {
+ RSC_CARVEOUT = 0,
+ RSC_DEVMEM = 1,
+ RSC_TRACE = 2,
+ RSC_VRING = 3,
+ RSC_VIRTIO_DEV = 4,
+ RSC_VIRTIO_CFG = 5,
+};
+
+Most of the resource entries share the basic idea of address/length
+negotiation with the host: the firmware usually asks for memory
+of size 'len' bytes, and the host needs to allocate it and provide
+the device/physical address (when relevant) in 'da'/'pa' respectively.
+
+If the firmware is compiled with hard coded device addresses, and
+can't handle dynamically allocated 'da' values, then the 'da' field
+will contain the expected device addresses (today we actually only support
+this scheme, as there aren't yet any use cases for dynamically allocated
+device addresses).
+
+We also expect that platform-specific resource entries will show up
+at some point. When that happens, we could easily add a new RSC_PLAFORM
+type, and hand those resources to the platform-specific rproc driver to handle.
+
+7. Virtio and remoteproc
+
+The firmware should provide remoteproc information about virtio devices
+that it supports, and their configurations: a RSC_VIRTIO_DEV resource entry
+should specify the virtio device id, and subsequent RSC_VRING resource entries
+should indicate the vring size (i.e. how many buffers do they support) and
+where should they be mapped (i.e. which device address). Note: the alignment
+between the consumer and producer parts of the vring is assumed to be 4096.
+
+At this point we only support a single virtio rpmsg device per remote
+processor, but the plan is to remove this limitation. In addition, once we
+move to TLV-based resource table, the plan is to have a single RSC_VIRTIO
+entry per supported virtio device, which will include the virtio header,
+the vrings information and the virtio config space.
+
+Of course, RSC_VIRTIO resource entries are only good enough for static
+allocation of virtio devices. Dynamic allocations will also be made possible
+using the rpmsg bus (similar to how we already do dynamic allocations of
+rpmsg channels; read more about it in rpmsg.txt).