diff options
Diffstat (limited to 'Documentation/scsi/aic7xxx.txt')
| -rw-r--r-- | Documentation/scsi/aic7xxx.txt | 414 |
1 files changed, 414 insertions, 0 deletions
diff --git a/Documentation/scsi/aic7xxx.txt b/Documentation/scsi/aic7xxx.txt new file mode 100644 index 000000000000..160e7354cd1e --- /dev/null +++ b/Documentation/scsi/aic7xxx.txt @@ -0,0 +1,414 @@ +==================================================================== += Adaptec Aic7xxx Fast -> Ultra160 Family Manager Set v6.2.28 = += README for = += The Linux Operating System = +==================================================================== + +The following information is available in this file: + + 1. Supported Hardware + 2. Version History + 3. Command Line Options + 4. Contacting Adaptec + +1. Supported Hardware + + The following Adaptec SCSI Chips and Host Adapters are supported by + the aic7xxx driver. + + Chip MIPS Host Bus MaxSync MaxWidth SCBs Notes + --------------------------------------------------------------- + aic7770 10 EISA/VL 10MHz 16Bit 4 1 + aic7850 10 PCI/32 10MHz 8Bit 3 + aic7855 10 PCI/32 10MHz 8Bit 3 + aic7856 10 PCI/32 10MHz 8Bit 3 + aic7859 10 PCI/32 20MHz 8Bit 3 + aic7860 10 PCI/32 20MHz 8Bit 3 + aic7870 10 PCI/32 10MHz 16Bit 16 + aic7880 10 PCI/32 20MHz 16Bit 16 + aic7890 20 PCI/32 40MHz 16Bit 16 3 4 5 6 7 8 + aic7891 20 PCI/64 40MHz 16Bit 16 3 4 5 6 7 8 + aic7892 20 PCI/64-66 80MHz 16Bit 16 3 4 5 6 7 8 + aic7895 15 PCI/32 20MHz 16Bit 16 2 3 4 5 + aic7895C 15 PCI/32 20MHz 16Bit 16 2 3 4 5 8 + aic7896 20 PCI/32 40MHz 16Bit 16 2 3 4 5 6 7 8 + aic7897 20 PCI/64 40MHz 16Bit 16 2 3 4 5 6 7 8 + aic7899 20 PCI/64-66 80MHz 16Bit 16 2 3 4 5 6 7 8 + + 1. Multiplexed Twin Channel Device - One controller servicing two + busses. + 2. Multi-function Twin Channel Device - Two controllers on one chip. + 3. Command Channel Secondary DMA Engine - Allows scatter gather list + and SCB prefetch. + 4. 64 Byte SCB Support - Allows disconnected, unttagged request table + for all possible target/lun combinations. + 5. Block Move Instruction Support - Doubles the speed of certain + sequencer operations. + 6. `Bayonet' style Scatter Gather Engine - Improves S/G prefetch + performance. + 7. Queuing Registers - Allows queuing of new transactions without + pausing the sequencer. + 8. Multiple Target IDs - Allows the controller to respond to selection + as a target on multiple SCSI IDs. + + Controller Chip Host-Bus Int-Connectors Ext-Connectors Notes + -------------------------------------------------------------------------- + AHA-274X[A] aic7770 EISA SE-50M SE-HD50F + AHA-274X[A]W aic7770 EISA SE-HD68F SE-HD68F + SE-50M + AHA-274X[A]T aic7770 EISA 2 X SE-50M SE-HD50F + AHA-2842 aic7770 VL SE-50M SE-HD50F + AHA-2940AU aic7860 PCI/32 SE-50M SE-HD50F + AVA-2902I aic7860 PCI/32 SE-50M + AVA-2902E aic7860 PCI/32 SE-50M + AVA-2906 aic7856 PCI/32 SE-50M SE-DB25F + APC-7850 aic7850 PCI/32 SE-50M 1 + AVA-2940 aic7860 PCI/32 SE-50M + AHA-2920B aic7860 PCI/32 SE-50M + AHA-2930B aic7860 PCI/32 SE-50M + AHA-2920C aic7856 PCI/32 SE-50M SE-HD50F + AHA-2930C aic7860 PCI/32 SE-50M + AHA-2930C aic7860 PCI/32 SE-50M + AHA-2910C aic7860 PCI/32 SE-50M + AHA-2915C aic7860 PCI/32 SE-50M + AHA-2940AU/CN aic7860 PCI/32 SE-50M SE-HD50F + AHA-2944W aic7870 PCI/32 HVD-HD68F HVD-HD68F + HVD-50M + AHA-3940W aic7870 PCI/32 2 X SE-HD68F SE-HD68F 2 + AHA-2940UW aic7880 PCI/32 SE-HD68F + SE-50M SE-HD68F + AHA-2940U aic7880 PCI/32 SE-50M SE-HD50F + AHA-2940D aic7880 PCI/32 + aHA-2940 A/T aic7880 PCI/32 + AHA-2940D A/T aic7880 PCI/32 + AHA-3940UW aic7880 PCI/32 2 X SE-HD68F SE-HD68F 3 + AHA-3940UWD aic7880 PCI/32 2 X SE-HD68F 2 X SE-VHD68F 3 + AHA-3940U aic7880 PCI/32 2 X SE-50M SE-HD50F 3 + AHA-2944UW aic7880 PCI/32 HVD-HD68F HVD-HD68F + HVD-50M + AHA-3944UWD aic7880 PCI/32 2 X HVD-HD68F 2 X HVD-VHD68F 3 + AHA-4944UW aic7880 PCI/32 + AHA-2930UW aic7880 PCI/32 + AHA-2940UW Pro aic7880 PCI/32 SE-HD68F SE-HD68F 4 + SE-50M + AHA-2940UW/CN aic7880 PCI/32 + AHA-2940UDual aic7895 PCI/32 + AHA-2940UWDual aic7895 PCI/32 + AHA-3940UWD aic7895 PCI/32 + AHA-3940AUW aic7895 PCI/32 + AHA-3940AUWD aic7895 PCI/32 + AHA-3940AU aic7895 PCI/32 + AHA-3944AUWD aic7895 PCI/32 2 X HVD-HD68F 2 X HVD-VHD68F + AHA-2940U2B aic7890 PCI/32 LVD-HD68F LVD-HD68F + AHA-2940U2 OEM aic7891 PCI/64 + AHA-2940U2W aic7890 PCI/32 LVD-HD68F LVD-HD68F + SE-HD68F + SE-50M + AHA-2950U2B aic7891 PCI/64 LVD-HD68F LVD-HD68F + AHA-2930U2 aic7890 PCI/32 LVD-HD68F SE-HD50F + SE-50M + AHA-3950U2B aic7897 PCI/64 + AHA-3950U2D aic7897 PCI/64 + AHA-29160 aic7892 PCI/64-66 + AHA-29160 CPQ aic7892 PCI/64-66 + AHA-29160N aic7892 PCI/32 LVD-HD68F SE-HD50F + SE-50M + AHA-29160LP aic7892 PCI/64-66 + AHA-19160 aic7892 PCI/64-66 + AHA-29150LP aic7892 PCI/64-66 + AHA-29130LP aic7892 PCI/64-66 + AHA-3960D aic7899 PCI/64-66 2 X LVD-HD68F 2 X LVD-VHD68F + LVD-50M + AHA-3960D CPQ aic7899 PCI/64-66 2 X LVD-HD68F 2 X LVD-VHD68F + LVD-50M + AHA-39160 aic7899 PCI/64-66 2 X LVD-HD68F 2 X LVD-VHD68F + LVD-50M + + 1. No BIOS support + 2. DEC21050 PCI-PCI bridge with multiple controller chips on secondary bus + 3. DEC2115X PCI-PCI bridge with multiple controller chips on secondary bus + 4. All three SCSI connectors may be used simultaneously without + SCSI "stub" effects. + +2. Version History + 6.2.36 (June 3rd, 2003) + - Correct code that disables PCI parity error checking. + - Correct and simplify handling of the ignore wide residue + message. The previous code would fail to report a residual + if the transaction data length was even and we received + an IWR message. + - Add support for the 2.5.X EISA framework. + - Update for change in 2.5.X SCSI proc FS interface. + - Correct Domain Validation command-line option parsing. + - When negotiation async via an 8bit WDTR message, send + an SDTR with an offset of 0 to be sure the target + knows we are async. This works around a firmware defect + in the Quantum Atlas 10K. + - Clear PCI error state during driver attach so that we + don't disable memory mapped I/O due to a stray write + by some other driver probe that occurred before we + claimed the controller. + + 6.2.35 (May 14th, 2003) + - Fix a few GCC 3.3 compiler warnings. + - Correct operation on EISA Twin Channel controller. + - Add support for 2.5.X's scsi_report_device_reset(). + + 6.2.34 (May 5th, 2003) + - Fix locking regression instroduced in 6.2.29 that + could cuase a lock order reversal between the io_request_lock + and our per-softc lock. This was only possible on RH9, + SuSE, and kernel.org 2.4.X kernels. + + 6.2.33 (April 30th, 2003) + - Dynamically disable PCI parity error reporting after + 10 errors are reported to the user. These errors are + the result of some other device issuing PCI transactions + with bad parity. Once the user has been informed of the + problem, continuing to report the errors just degrades + our performance. + + 6.2.32 (March 28th, 2003) + - Dynamically sized S/G lists to avoid SCSI malloc + pool fragmentation and SCSI mid-layer deadlock. + + 6.2.28 (January 20th, 2003) + - Domain Validation Fixes + - Add ability to disable PCI parity error checking. + - Enhanced Memory Mapped I/O probe + + 6.2.20 (November 7th, 2002) + - Added Domain Validation. + +3. Command Line Options + + WARNING: ALTERING OR ADDING THESE DRIVER PARAMETERS + INCORRECTLY CAN RENDER YOUR SYSTEM INOPERABLE. + USE THEM WITH CAUTION. + + Edit the file "modprobe.conf" in the directory /etc and add/edit a + line containing 'options aic7xxx aic7xxx=[command[,command...]]' where + 'command' is one or more of the following: + ----------------------------------------------------------------- + Option: verbose + Definition: enable additional informative messages during + driver operation. + Possible Values: This option is a flag + Default Value: disabled + ----------------------------------------------------------------- + Option: debug:[value] + Definition: Enables various levels of debugging information + Possible Values: 0x0000 = no debugging, 0xffff = full debugging + Default Value: 0x0000 + ----------------------------------------------------------------- + Option: no_probe + Option: probe_eisa_vl + Definition: Do not probe for EISA/VLB controllers. + This is a toggle. If the driver is compiled + to not probe EISA/VLB controllers by default, + specifying "no_probe" will enable this probing. + If the driver is compiled to probe EISA/VLB + controllers by default, specifying "no_probe" + will disable this probing. + Possible Values: This option is a toggle + Default Value: EISA/VLB probing is disabled by default. + ----------------------------------------------------------------- + Option: pci_parity + Definition: Toggles the detection of PCI parity errors. + On many motherboards with VIA chipsets, + PCI parity is not generated correctly on the + PCI bus. It is impossible for the hardware to + differentiate between these "spurious" parity + errors and real parity errors. The symptom of + this problem is a stream of the message: + "scsi0: Data Parity Error Detected during address or write data phase" + output by the driver. + Possible Values: This option is a toggle + Default Value: PCI Parity Error reporting is disabled + ----------------------------------------------------------------- + Option: no_reset + Definition: Do not reset the bus during the initial probe + phase + Possible Values: This option is a flag + Default Value: disabled + ----------------------------------------------------------------- + Option: extended + Definition: Force extended translation on the controller + Possible Values: This option is a flag + Default Value: disabled + ----------------------------------------------------------------- + Option: periodic_otag + Definition: Send an ordered tag periodically to prevent + tag starvation. Needed for some older devices + Possible Values: This option is a flag + Default Value: disabled + ----------------------------------------------------------------- + Option: reverse_scan + Definition: Probe the scsi bus in reverse order, starting + with target 15 + Possible Values: This option is a flag + Default Value: disabled + ----------------------------------------------------------------- + Option: global_tag_depth:[value] + Definition: Global tag depth for all targets on all busses. + This option sets the default tag depth which + may be selectively overridden vi the tag_info + option. + Possible Values: 1 - 253 + Default Value: 32 + ----------------------------------------------------------------- + Option: tag_info:{{value[,value...]}[,{value[,value...]}...]} + Definition: Set the per-target tagged queue depth on a + per controller basis. Both controllers and targets + may be ommitted indicating that they should retain + the default tag depth. + Examples: tag_info:{{16,32,32,64,8,8,,32,32,32,32,32,32,32,32,32} + On Controller 0 + specifies a tag depth of 16 for target 0 + specifies a tag depth of 64 for target 3 + specifies a tag depth of 8 for targets 4 and 5 + leaves target 6 at the default + specifies a tag depth of 32 for targets 1,2,7-15 + All other targets retain the default depth. + + tag_info:{{},{32,,32}} + On Controller 1 + specifies a tag depth of 32 for targets 0 and 2 + All other targets retain the default depth. + + Possible Values: 1 - 253 + Default Value: 32 + ----------------------------------------------------------------- + Option: seltime:[value] + Definition: Specifies the selection timeout value + Possible Values: 0 = 256ms, 1 = 128ms, 2 = 64ms, 3 = 32ms + Default Value: 0 + ----------------------------------------------------------------- + Option: dv: {value[,value...]} + Definition: Set Domain Validation Policy on a per-controller basis. + Controllers may be ommitted indicating that + they should retain the default read streaming setting. + Example: dv:{-1,0,,1,1,0} + On Controller 0 leave DV at its default setting. + On Controller 1 disable DV. + Skip configuration on Controller 2. + On Controllers 3 and 4 enable DV. + On Controller 5 disable DV. + + Possible Values: < 0 Use setting from serial EEPROM. + 0 Disable DV + > 0 Enable DV + + Default Value: SCSI-Select setting on controllers with a SCSI Select + option for DV. Otherwise, on for controllers supporting + U160 speeds and off for all other controller types. + ----------------------------------------------------------------- + + Example: + 'options aic7xxx aic7xxx=verbose,no_probe,tag_info:{{},{,,10}},seltime:1" + enables verbose logging, Disable EISA/VLB probing, + and set tag depth on Controller 1/Target 2 to 10 tags. + +3. Contacting Adaptec + + A Technical Support Identification (TSID) Number is required for + Adaptec technical support. + - The 12-digit TSID can be found on the white barcode-type label + included inside the box with your product. The TSID helps us + provide more efficient service by accurately identifying your + product and support status. + Support Options + - Search the Adaptec Support Knowledgebase (ASK) at + http://ask.adaptec.com for articles, troubleshooting tips, and + frequently asked questions for your product. + - For support via Email, submit your question to Adaptec's + Technical Support Specialists at http://ask.adaptec.com. + + North America + - Visit our Web site at http://www.adaptec.com. + - To speak with a Fibre Channel/RAID/External Storage Technical + Support Specialist, call 1-321-207-2000, + Hours: Monday-Friday, 3:00 A.M. to 5:00 P.M., PST. + (Not open on holidays) + - For Technical Support in all other technologies including + SCSI, call 1-408-934-7274, + Hours: Monday-Friday, 6:00 A.M. to 5:00 P.M., PST. + (Not open on holidays) + - For after hours support, call 1-800-416-8066 ($99/call, + $149/call on holidays) + - To order Adaptec products including software and cables, call + 1-800-442-7274 or 1-408-957-7274. You can also visit our + online store at http://www.adaptecstore.com + + Europe + - Visit our Web site at http://www.adaptec-europe.com. + - English and French: To speak with a Technical Support + Specialist, call one of the following numbers: + - English: +32-2-352-3470 + - French: +32-2-352-3460 + Hours: Monday-Thursday, 10:00 to 12:30, 13:30 to 17:30 CET + Friday, 10:00 to 12:30, 13:30 to 16:30 CET + - German: To speak with a Technical Support Specialist, + call +49-89-456-40660 + Hours: Monday-Thursday, 09:30 to 12:30, 13:30 to 16:30 CET + Friday, 09:30 to 12:30, 13:30 to 15:00 CET + - To order Adaptec products, including accessories and cables: + - UK: +0800-96-65-26 or fax +0800-731-02-95 + - Other European countries: +32-11-300-379 + + Australia and New Zealand + - Visit our Web site at http://www.adaptec.com.au. + - To speak with a Technical Support Specialist, call + +612-9416-0698 + Hours: Monday-Friday, 10:00 A.M. to 4:30 P.M., EAT + (Not open on holidays) + + Japan + - To speak with a Technical Support Specialist, call + +81-3-5308-6120 + Hours: Monday-Friday, 9:00 a.m. to 12:00 p.m., 1:00 p.m. to + 6:00 p.m. TSC + + Hong Kong and China + - To speak with a Technical Support Specialist, call + +852-2869-7200 + Hours: Monday-Friday, 10:00 to 17:00. + - Fax Technical Support at +852-2869-7100. + + Singapore + - To speak with a Technical Support Specialist, call + +65-245-7470 + Hours: Monday-Friday, 10:00 to 17:00. + - Fax Technical Support at +852-2869-7100 + +------------------------------------------------------------------- +/* + * Copyright (c) 2003 Adaptec Inc. 691 S. Milpitas Blvd., Milpitas CA 95035 USA. + * All rights reserved. + * + * You are permitted to redistribute, use and modify this README file in whole + * or in part in conjunction with redistribution of software governed by the + * General Public License, provided that the following conditions are met: + * 1. Redistributions of README file must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. The name of the author may not be used to endorse or promote products + * derived from this software without specific prior written permission. + * 3. Modifications or new contributions must be attributed in a copyright + * notice identifying the author ("Contributor") and added below the + * original copyright notice. The copyright notice is for purposes of + * identifying contributors and should not be deemed as permission to alter + * the permissions given by Adaptec. + * + * THIS README FILE IS PROVIDED BY ADAPTEC AND CONTRIBUTORS ``AS IS'' AND + * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY + * WARRANTIES OF NON-INFRINGEMENT OR THE IMPLIED WARRANTIES OF MERCHANTABILITY + * AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL + * ADAPTEC OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, + * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED + * TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR + * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF + * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING + * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS README + * FILE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + */ |