diff options
Diffstat (limited to 'Documentation/sound/oss/OPL3-SA2')
| -rw-r--r-- | Documentation/sound/oss/OPL3-SA2 | 210 |
1 files changed, 210 insertions, 0 deletions
diff --git a/Documentation/sound/oss/OPL3-SA2 b/Documentation/sound/oss/OPL3-SA2 new file mode 100644 index 000000000000..d8b6d2bbada6 --- /dev/null +++ b/Documentation/sound/oss/OPL3-SA2 @@ -0,0 +1,210 @@ +Documentation for the OPL3-SA2, SA3, and SAx driver (opl3sa2.o) +--------------------------------------------------------------- + +Scott Murray, scott@spiteful.org +January 7, 2001 + +NOTE: All trade-marked terms mentioned below are properties of their + respective owners. + + +Supported Devices +----------------- + +This driver is for PnP soundcards based on the following Yamaha audio +controller chipsets: + +YMF711 aka OPL3-SA2 +YMF715 and YMF719 aka OPL3-SA3 + +Up until recently (December 2000), I'd thought the 719 to be a +different chipset, the OPL3-SAx. After an email exhange with +Yamaha, however, it turns out that the 719 is just a re-badged +715, and the chipsets are identical. The chipset detection code +has been updated to reflect this. + +Anyways, all of these chipsets implement the following devices: + +OPL3 FM synthesizer +Soundblaster Pro +Microsoft/Windows Sound System +MPU401 MIDI interface + +Note that this driver uses the MSS device, and to my knowledge these +chipsets enforce an either/or situation with the Soundblaster Pro +device and the MSS device. Since the MSS device has better +capabilities, I have implemented the driver to use it. + + +Mixer Channels +-------------- + +Older versions of this driver (pre-December 2000) had two mixers, +an OPL3-SA2 or SA3 mixer and a MSS mixer. The OPL3-SA[23] mixer +device contained a superset of mixer channels consisting of its own +channels and all of the MSS mixer channels. To simplify the driver +considerably, and to partition functionality better, the OPL3-SA[23] +mixer device now contains has its own specific mixer channels. They +are: + +Volume - Hardware master volume control +Bass - SA3 only, now supports left and right channels +Treble - SA3 only, now supports left and right channels +Microphone - Hardware microphone input volume control +Digital1 - Yamaha 3D enhancement "Wide" mixer + +All other mixer channels (e.g. "PCM", "CD", etc.) now have to be +controlled via the "MS Sound System (CS4231)" mixer. To facilitate +this, the mixer device creation order has been switched so that +the MSS mixer is created first. This allows accessing the majority +of the useful mixer channels even via single mixer-aware tools +such as "aumix". + + +Plug 'n Play +------------ + +In previous kernels (2.2.x), some configuration was required to +get the driver to talk to the card. Being the new millennium and +all, the 2.4.x kernels now support auto-configuration if ISA PnP +support is configured in. Theoretically, the driver even supports +having more than one card in this case. + +With the addition of PnP support to the driver, two new parameters +have been added to control it: + +isapnp - set to 0 to disable ISA PnP card detection + +multiple - set to 0 to disable multiple PnP card detection + + +Optional Parameters +------------------- + +Recent (December 2000) additions to the driver (based on a patch +provided by Peter Englmaier) are two new parameters: + +ymode - Set Yamaha 3D enhancement mode: + 0 = Desktop/Normal 5-12 cm speakers + 1 = Notebook PC (1) 3 cm speakers + 2 = Notebook PC (2) 1.5 cm speakers + 3 = Hi-Fi 16-38 cm speakers + +loopback - Set A/D input source. Useful for echo cancellation: + 0 = Mic Right channel (default) + 1 = Mono output loopback + +The ymode parameter has been tested and does work. The loopback +parameter, however, is untested. Any feedback on its usefulness +would be appreciated. + + +Manual Configuration +-------------------- + +If for some reason you decide not to compile ISA PnP support into +your kernel, or disabled the driver's usage of it by setting the +isapnp parameter as discussed above, then you will need to do some +manual configuration. There are two ways of doing this. The most +common is to use the isapnptools package to initialize the card, and +use the kernel module form of the sound subsystem and sound drivers. +Alternatively, some BIOS's allow manual configuration of installed +PnP devices in a BIOS menu, which should allow using the non-modular +sound drivers, i.e. built into the kernel. + +I personally use isapnp and modules, and do not have access to a PnP +BIOS machine to test. If you have such a beast, configuring the +driver to be built into the kernel should just work (thanks to work +done by David Luyer <luyer@ucs.uwa.edu.au>). You will still need +to specify settings, which can be done by adding: + +opl3sa2=<io>,<irq>,<dma>,<dma2>,<mssio>,<mpuio> + +to the kernel command line. For example: + +opl3sa2=0x370,5,0,1,0x530,0x330 + +If you are instead using the isapnp tools (as most people have been +before Linux 2.4.x), follow the directions in their documentation to +produce a configuration file. Here is the relevant excerpt I used to +use for my SA3 card from my isapnp.conf: + +(CONFIGURE YMH0800/-1 (LD 0 + +# NOTE: IO 0 is for the unused SoundBlaster part of the chipset. +(IO 0 (BASE 0x0220)) +(IO 1 (BASE 0x0530)) +(IO 2 (BASE 0x0388)) +(IO 3 (BASE 0x0330)) +(IO 4 (BASE 0x0370)) +(INT 0 (IRQ 5 (MODE +E))) +(DMA 0 (CHANNEL 0)) +(DMA 1 (CHANNEL 1)) + +Here, note that: + +Port Acceptable Range Purpose +---- ---------------- ------- +IO 0 0x0220 - 0x0280 SB base address, unused. +IO 1 0x0530 - 0x0F48 MSS base address +IO 2 0x0388 - 0x03F8 OPL3 base address +IO 3 0x0300 - 0x0334 MPU base address +IO 4 0x0100 - 0x0FFE card's own base address for its control I/O ports + +The IRQ and DMA values can be any that are considered acceptable for a +MSS. Assuming you've got isapnp all happy, then you should be able to +do something like the following (which matches up with the isapnp +configuration above): + +modprobe mpu401 +modprobe ad1848 +modprobe opl3sa2 io=0x370 mss_io=0x530 mpu_io=0x330 irq=5 dma=0 dma2=1 +modprobe opl3 io=0x388 + +See the section "Automatic Module Loading" below for how to set up +/etc/modprobe.conf to automate this. + +An important thing to remember that the opl3sa2 module's io argument is +for it's own control port, which handles the card's master mixer for +volume (on all cards), and bass and treble (on SA3 cards). + + +Troubleshooting +--------------- + +If all goes well and you see no error messages, you should be able to +start using the sound capabilities of your system. If you get an +error message while trying to insert the opl3sa2 module, then make +sure that the values of the various arguments match what you specified +in your isapnp configuration file, and that there is no conflict with +another device for an I/O port or interrupt. Checking the contents of +/proc/ioports and /proc/interrupts can be useful to see if you're +butting heads with another device. + +If you still cannot get the module to load, look at the contents of +your system log file, usually /var/log/messages. If you see the +message "opl3sa2: Unknown Yamaha audio controller version", then you +have a different chipset version than I've encountered so far. Look +for all messages in the log file that start with "opl3sa2: " and see +if they provide any clues. If you do not see the chipset version +message, and none of the other messages present in the system log are +helpful, email me some details and I'll try my best to help. + + +Automatic Module Loading +------------------------ + +Lastly, if you're using modules and want to set up automatic module +loading with kmod, the kernel module loader, here is the section I +currently use in my modprobe.conf file: + +# Sound +alias sound-slot-0 opl3sa2 +options opl3sa2 io=0x370 mss_io=0x530 mpu_io=0x330 irq=7 dma=0 dma2=3 +options opl3 io=0x388 + +That's all it currently takes to get an OPL3-SA3 card working on my +system. Once again, if you have any other problems, email me at the +address listed above. + +Scott |