diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/devicetree/bindings/gpio/gpio-fan.txt | 19 | ||||
| -rw-r--r-- | Documentation/hwmon/it87 | 48 | ||||
| -rw-r--r-- | Documentation/hwmon/jc42 | 8 | ||||
| -rw-r--r-- | Documentation/hwmon/nct7904 | 60 |
4 files changed, 115 insertions, 20 deletions
diff --git a/Documentation/devicetree/bindings/gpio/gpio-fan.txt b/Documentation/devicetree/bindings/gpio/gpio-fan.txt index 2dd457a3469a..439a7430fc68 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-fan.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-fan.txt @@ -2,15 +2,20 @@ Bindings for fan connected to GPIO lines Required properties: - compatible : "gpio-fan" + +Optional properties: - gpios: Specifies the pins that map to bits in the control value, ordered MSB-->LSB. - gpio-fan,speed-map: A mapping of possible fan RPM speeds and the control value that should be set to achieve them. This array must have the RPM values in ascending order. - -Optional properties: - alarm-gpios: This pin going active indicates something is wrong with the fan, and a udev event will be fired. +- cooling-cells: If used as a cooling device, must be <2> + Also see: Documentation/devicetree/bindings/thermal/thermal.txt + min and max states are derived from the speed-map of the fan. + +Note: At least one the "gpios" or "alarm-gpios" properties must be set. Examples: @@ -23,3 +28,13 @@ Examples: 6000 2>; alarm-gpios = <&gpio1 15 1>; }; + gpio_fan_cool: gpio_fan { + compatible = "gpio-fan"; + gpios = <&gpio2 14 1 + &gpio2 13 1>; + gpio-fan,speed-map = <0 0>, + <3000 1>, + <6000 2>; + alarm-gpios = <&gpio2 15 1>; + #cooling-cells = <2>; /* min followed by max */ + }; diff --git a/Documentation/hwmon/it87 b/Documentation/hwmon/it87 index fe80e9adebfa..e87294878334 100644 --- a/Documentation/hwmon/it87 +++ b/Documentation/hwmon/it87 @@ -6,6 +6,10 @@ Supported chips: Prefix: 'it8603' Addresses scanned: from Super I/O config space (8 I/O ports) Datasheet: Not publicly available + * IT8620E + Prefix: 'it8620' + Addresses scanned: from Super I/O config space (8 I/O ports) + Datasheet: Not publicly available * IT8705F Prefix: 'it87' Addresses scanned: from Super I/O config space (8 I/O ports) @@ -42,6 +46,10 @@ Supported chips: Prefix: 'it8772' Addresses scanned: from Super I/O config space (8 I/O ports) Datasheet: Not publicly available + * IT8781F + Prefix: 'it8781' + Addresses scanned: from Super I/O config space (8 I/O ports) + Datasheet: Not publicly available * IT8782F Prefix: 'it8782' Addresses scanned: from Super I/O config space (8 I/O ports) @@ -50,6 +58,14 @@ Supported chips: Prefix: 'it8783' Addresses scanned: from Super I/O config space (8 I/O ports) Datasheet: Not publicly available + * IT8786E + Prefix: 'it8786' + Addresses scanned: from Super I/O config space (8 I/O ports) + Datasheet: Not publicly available + * IT8790E + Prefix: 'it8790' + Addresses scanned: from Super I/O config space (8 I/O ports) + Datasheet: Not publicly available * SiS950 [clone of IT8705F] Prefix: 'it87' Addresses scanned: from Super I/O config space (8 I/O ports) @@ -94,9 +110,10 @@ motherboard models. Description ----------- -This driver implements support for the IT8603E, IT8623E, IT8705F, IT8712F, -IT8716F, IT8718F, IT8720F, IT8721F, IT8726F, IT8728F, IT8758E, IT8771E, -IT8772E, IT8782F, IT8783E/F, and SiS950 chips. +This driver implements support for the IT8603E, IT8620E, IT8623E, IT8705F, +IT8712F, IT8716F, IT8718F, IT8720F, IT8721F, IT8726F, IT8728F, IT8758E, +IT8771E, IT8772E, IT8781F, IT8782F, IT8783E/F, IT8786E, IT8790E, and SiS950 +chips. These chips are 'Super I/O chips', supporting floppy disks, infrared ports, joysticks and other miscellaneous stuff. For hardware monitoring, they @@ -120,11 +137,11 @@ The IT8716F, IT8718F, IT8720F, IT8721F/IT8758E and later IT8712F revisions have support for 2 additional fans. The additional fans are supported by the driver. -The IT8716F, IT8718F, IT8720F, IT8721F/IT8758E, IT8782F, IT8783E/F, and late -IT8712F and IT8705F also have optional 16-bit tachometer counters for fans 1 to -3. This is better (no more fan clock divider mess) but not compatible with the -older chips and revisions. The 16-bit tachometer mode is enabled by the driver -when one of the above chips is detected. +The IT8716F, IT8718F, IT8720F, IT8721F/IT8758E, IT8781F, IT8782F, IT8783E/F, +and late IT8712F and IT8705F also have optional 16-bit tachometer counters +for fans 1 to 3. This is better (no more fan clock divider mess) but not +compatible with the older chips and revisions. The 16-bit tachometer mode +is enabled by the driver when one of the above chips is detected. The IT8726F is just bit enhanced IT8716F with additional hardware for AMD power sequencing. Therefore the chip will appear as IT8716F @@ -134,8 +151,13 @@ The IT8728F, IT8771E, and IT8772E are considered compatible with the IT8721F, until a datasheet becomes available (hopefully.) The IT8603E/IT8623E is a custom design, hardware monitoring part is similar to -IT8728F. It only supports 16-bit fan mode, the full speed mode of the -fan is not supported (value 0 of pwmX_enable). +IT8728F. It only supports 3 fans, 16-bit fan mode, and the full speed mode +of the fan is not supported (value 0 of pwmX_enable). + +The IT8620E is another custom design, hardware monitoring part is similar to +IT8728F. It only supports 16-bit fan mode. + +The IT8790E supports up to 3 fans. 16-bit fan mode is always enabled. Temperatures are measured in degrees Celsius. An alarm is triggered once when the Overtemperature Shutdown limit is crossed. @@ -156,10 +178,10 @@ inputs can measure voltages between 0 and 4.08 volts, with a resolution of 0.016 volt (except IT8603E, IT8721F/IT8758E and IT8728F: 0.012 volt.) The battery voltage in8 does not have limit registers. -On the IT8603E, IT8721F/IT8758E, IT8782F, and IT8783E/F, some voltage inputs -are internal and scaled inside the chip: +On the IT8603E, IT8721F/IT8758E, IT8781F, IT8782F, and IT8783E/F, some +voltage inputs are internal and scaled inside the chip: * in3 (optional) -* in7 (optional for IT8782F and IT8783E/F) +* in7 (optional for IT8781F, IT8782F, and IT8783E/F) * in8 (always) * in9 (relevant for IT8603E only) The driver handles this transparently so user-space doesn't have to care. diff --git a/Documentation/hwmon/jc42 b/Documentation/hwmon/jc42 index f3893f7440de..f7f1830a2566 100644 --- a/Documentation/hwmon/jc42 +++ b/Documentation/hwmon/jc42 @@ -11,12 +11,10 @@ Supported chips: http://www.atmel.com/Images/doc8711.pdf http://www.atmel.com/Images/Atmel-8852-SEEPROM-AT30TSE002A-Datasheet.pdf http://www.atmel.com/Images/Atmel-8868-DTS-AT30TSE004A-Datasheet.pdf - * IDT TSE2002B3, TSE2002GB2, TS3000B3, TS3000GB2 + * IDT TSE2002B3, TSE2002GB2, TSE2004GB2, TS3000B3, TS3000GB0, TS3000GB2, + TS3001GB2 Datasheets: - http://www.idt.com/sites/default/files/documents/IDT_TSE2002B3C_DST_20100512_120303152056.pdf - http://www.idt.com/sites/default/files/documents/IDT_TSE2002GB2A1_DST_20111107_120303145914.pdf - http://www.idt.com/sites/default/files/documents/IDT_TS3000B3A_DST_20101129_120303152013.pdf - http://www.idt.com/sites/default/files/documents/IDT_TS3000GB2A1_DST_20111104_120303151012.pdf + Available from IDT web site * Maxim MAX6604 Datasheets: http://datasheets.maxim-ic.com/en/ds/MAX6604.pdf diff --git a/Documentation/hwmon/nct7904 b/Documentation/hwmon/nct7904 new file mode 100644 index 000000000000..014f112e2a14 --- /dev/null +++ b/Documentation/hwmon/nct7904 @@ -0,0 +1,60 @@ +Kernel driver nct7904 +==================== + +Supported chip: + * Nuvoton NCT7904D + Prefix: nct7904 + Addresses: I2C 0x2d, 0x2e + Datasheet: Publicly available at Nuvoton website + http://www.nuvoton.com/ + +Author: Vadim V. Vlasov <vvlasov@dev.rtsoft.ru> + + +Description +----------- + +The NCT7904D is a hardware monitor supporting up to 20 voltage sensors, +internal temperature sensor, Intel PECI and AMD SB-TSI CPU temperature +interface, up to 12 fan tachometer inputs, up to 4 fan control channels +with SmartFan. + + +Sysfs entries +------------- + +Currently, the driver supports only the following features: + +in[1-20]_input Input voltage measurements (mV) + +fan[1-12]_input Fan tachometer measurements (rpm) + +temp1_input Local temperature (1/1000 degree, + 0.125 degree resolution) + +temp[2-9]_input CPU temperatures (1/1000 degree, + 0.125 degree resolution) + +fan[1-4]_mode R/W, 0/1 for manual or SmartFan mode + Setting SmartFan mode is supported only if it has been + previously configured by BIOS (or configuration EEPROM) + +fan[1-4]_pwm R/O in SmartFan mode, R/W in manual control mode + +The driver checks sensor control registers and does not export the sensors +that are not enabled. Anyway, a sensor that is enabled may actually be not +connected and thus provide zero readings. + + +Limitations +----------- + +The following features are not supported in current version: + + - SmartFan control + - Watchdog + - GPIO + - external temperature sensors + - SMI + - min/max values + - many other... |