diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/ab8500.txt | 6 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/tty/serial/of-serial.txt | 3 | ||||
| -rw-r--r-- | Documentation/hwmon/lm75 | 2 | ||||
| -rw-r--r-- | Documentation/input/alps.txt | 67 | ||||
| -rw-r--r-- | Documentation/networking/tuntap.txt | 77 | ||||
| -rw-r--r-- | Documentation/trace/ftrace.txt | 2 |
6 files changed, 143 insertions, 14 deletions
diff --git a/Documentation/devicetree/bindings/mfd/ab8500.txt b/Documentation/devicetree/bindings/mfd/ab8500.txt index 13b707b7355c..c3a14e0ad0ad 100644 --- a/Documentation/devicetree/bindings/mfd/ab8500.txt +++ b/Documentation/devicetree/bindings/mfd/ab8500.txt @@ -13,9 +13,6 @@ Required parent device properties: 4 = active high level-sensitive 8 = active low level-sensitive -Optional parent device properties: -- reg : contains the PRCMU mailbox address for the AB8500 i2c port - The AB8500 consists of a large and varied group of sub-devices: Device IRQ Names Supply Names Description @@ -86,9 +83,8 @@ Non-standard child device properties: - stericsson,amic2-bias-vamic1 : Analoge Mic wishes to use a non-standard Vamic - stericsson,earpeice-cmv : Earpeice voltage (only: 950 | 1100 | 1270 | 1580) -ab8500@5 { +ab8500 { compatible = "stericsson,ab8500"; - reg = <5>; /* mailbox 5 is i2c */ interrupts = <0 40 0x4>; interrupt-controller; #interrupt-cells = <2>; diff --git a/Documentation/devicetree/bindings/tty/serial/of-serial.txt b/Documentation/devicetree/bindings/tty/serial/of-serial.txt index 1e1145ca4f3c..8f01cb190f25 100644 --- a/Documentation/devicetree/bindings/tty/serial/of-serial.txt +++ b/Documentation/devicetree/bindings/tty/serial/of-serial.txt @@ -11,6 +11,9 @@ Required properties: - "nvidia,tegra20-uart" - "nxp,lpc3220-uart" - "ibm,qpace-nwp-serial" + - "altr,16550-FIFO32" + - "altr,16550-FIFO64" + - "altr,16550-FIFO128" - "serial" if the port type is unknown. - reg : offset and length of the register set for the device. - interrupts : should contain uart interrupt. diff --git a/Documentation/hwmon/lm75 b/Documentation/hwmon/lm75 index c91a1d15fa28..69af1c7db6b7 100644 --- a/Documentation/hwmon/lm75 +++ b/Documentation/hwmon/lm75 @@ -23,7 +23,7 @@ Supported chips: Datasheet: Publicly available at the Maxim website http://www.maxim-ic.com/ * Microchip (TelCom) TCN75 - Prefix: 'lm75' + Prefix: 'tcn75' Addresses scanned: none Datasheet: Publicly available at the Microchip website http://www.microchip.com/ diff --git a/Documentation/input/alps.txt b/Documentation/input/alps.txt index 3262b6e4d686..e544c7ff8cfa 100644 --- a/Documentation/input/alps.txt +++ b/Documentation/input/alps.txt @@ -3,10 +3,26 @@ ALPS Touchpad Protocol Introduction ------------ - -Currently the ALPS touchpad driver supports four protocol versions in use by -ALPS touchpads, called versions 1, 2, 3, and 4. Information about the various -protocol versions is contained in the following sections. +Currently the ALPS touchpad driver supports five protocol versions in use by +ALPS touchpads, called versions 1, 2, 3, 4 and 5. + +Since roughly mid-2010 several new ALPS touchpads have been released and +integrated into a variety of laptops and netbooks. These new touchpads +have enough behavior differences that the alps_model_data definition +table, describing the properties of the different versions, is no longer +adequate. The design choices were to re-define the alps_model_data +table, with the risk of regression testing existing devices, or isolate +the new devices outside of the alps_model_data table. The latter design +choice was made. The new touchpad signatures are named: "Rushmore", +"Pinnacle", and "Dolphin", which you will see in the alps.c code. +For the purposes of this document, this group of ALPS touchpads will +generically be called "new ALPS touchpads". + +We experimented with probing the ACPI interface _HID (Hardware ID)/_CID +(Compatibility ID) definition as a way to uniquely identify the +different ALPS variants but there did not appear to be a 1:1 mapping. +In fact, it appeared to be an m:n mapping between the _HID and actual +hardware type. Detection --------- @@ -20,9 +36,13 @@ If the E6 report is successful, the touchpad model is identified using the "E7 report" sequence: E8-E7-E7-E7-E9. The response is the model signature and is matched against known models in the alps_model_data_array. -With protocol versions 3 and 4, the E7 report model signature is always -73-02-64. To differentiate between these versions, the response from the -"Enter Command Mode" sequence must be inspected as described below. +For older touchpads supporting protocol versions 3 and 4, the E7 report +model signature is always 73-02-64. To differentiate between these +versions, the response from the "Enter Command Mode" sequence must be +inspected as described below. + +The new ALPS touchpads have an E7 signature of 73-03-50 or 73-03-0A but +seem to be better differentiated by the EC Command Mode response. Command Mode ------------ @@ -47,6 +67,14 @@ address of the register being read, and the third contains the value of the register. Registers are written by writing the value one nibble at a time using the same encoding used for addresses. +For the new ALPS touchpads, the EC command is used to enter command +mode. The response in the new ALPS touchpads is significantly different, +and more important in determining the behavior. This code has been +separated from the original alps_model_data table and put in the +alps_identify function. For example, there seem to be two hardware init +sequences for the "Dolphin" touchpads as determined by the second byte +of the EC response. + Packet Format ------------- @@ -187,3 +215,28 @@ There are several things worth noting here. well. So far no v4 devices with tracksticks have been encountered. + +ALPS Absolute Mode - Protocol Version 5 +--------------------------------------- +This is basically Protocol Version 3 but with different logic for packet +decode. It uses the same alps_process_touchpad_packet_v3 call with a +specialized decode_fields function pointer to correctly interpret the +packets. This appears to only be used by the Dolphin devices. + +For single-touch, the 6-byte packet format is: + + byte 0: 1 1 0 0 1 0 0 0 + byte 1: 0 x6 x5 x4 x3 x2 x1 x0 + byte 2: 0 y6 y5 y4 y3 y2 y1 y0 + byte 3: 0 M R L 1 m r l + byte 4: y10 y9 y8 y7 x10 x9 x8 x7 + byte 5: 0 z6 z5 z4 z3 z2 z1 z0 + +For mt, the format is: + + byte 0: 1 1 1 n3 1 n2 n1 x24 + byte 1: 1 y7 y6 y5 y4 y3 y2 y1 + byte 2: ? x2 x1 y12 y11 y10 y9 y8 + byte 3: 0 x23 x22 x21 x20 x19 x18 x17 + byte 4: 0 x9 x8 x7 x6 x5 x4 x3 + byte 5: 0 x16 x15 x14 x13 x12 x11 x10 diff --git a/Documentation/networking/tuntap.txt b/Documentation/networking/tuntap.txt index c0aab985bad9..949d5dcdd9a3 100644 --- a/Documentation/networking/tuntap.txt +++ b/Documentation/networking/tuntap.txt @@ -105,6 +105,83 @@ Copyright (C) 1999-2000 Maxim Krasnyansky <max_mk@yahoo.com> Proto [2 bytes] Raw protocol(IP, IPv6, etc) frame. + 3.3 Multiqueue tuntap interface: + + From version 3.8, Linux supports multiqueue tuntap which can uses multiple + file descriptors (queues) to parallelize packets sending or receiving. The + device allocation is the same as before, and if user wants to create multiple + queues, TUNSETIFF with the same device name must be called many times with + IFF_MULTI_QUEUE flag. + + char *dev should be the name of the device, queues is the number of queues to + be created, fds is used to store and return the file descriptors (queues) + created to the caller. Each file descriptor were served as the interface of a + queue which could be accessed by userspace. + + #include <linux/if.h> + #include <linux/if_tun.h> + + int tun_alloc_mq(char *dev, int queues, int *fds) + { + struct ifreq ifr; + int fd, err, i; + + if (!dev) + return -1; + + memset(&ifr, 0, sizeof(ifr)); + /* Flags: IFF_TUN - TUN device (no Ethernet headers) + * IFF_TAP - TAP device + * + * IFF_NO_PI - Do not provide packet information + * IFF_MULTI_QUEUE - Create a queue of multiqueue device + */ + ifr.ifr_flags = IFF_TAP | IFF_NO_PI | IFF_MULTI_QUEUE; + strcpy(ifr.ifr_name, dev); + + for (i = 0; i < queues; i++) { + if ((fd = open("/dev/net/tun", O_RDWR)) < 0) + goto err; + err = ioctl(fd, TUNSETIFF, (void *)&ifr); + if (err) { + close(fd); + goto err; + } + fds[i] = fd; + } + + return 0; + err: + for (--i; i >= 0; i--) + close(fds[i]); + return err; + } + + A new ioctl(TUNSETQUEUE) were introduced to enable or disable a queue. When + calling it with IFF_DETACH_QUEUE flag, the queue were disabled. And when + calling it with IFF_ATTACH_QUEUE flag, the queue were enabled. The queue were + enabled by default after it was created through TUNSETIFF. + + fd is the file descriptor (queue) that we want to enable or disable, when + enable is true we enable it, otherwise we disable it + + #include <linux/if.h> + #include <linux/if_tun.h> + + int tun_set_queue(int fd, int enable) + { + struct ifreq ifr; + + memset(&ifr, 0, sizeof(ifr)); + + if (enable) + ifr.ifr_flags = IFF_ATTACH_QUEUE; + else + ifr.ifr_flags = IFF_DETACH_QUEUE; + + return ioctl(fd, TUNSETQUEUE, (void *)&ifr); + } + Universal TUN/TAP device driver Frequently Asked Question. 1. What platforms are supported by TUN/TAP driver ? diff --git a/Documentation/trace/ftrace.txt b/Documentation/trace/ftrace.txt index 53d6a3c51d87..a372304aef10 100644 --- a/Documentation/trace/ftrace.txt +++ b/Documentation/trace/ftrace.txt @@ -1873,7 +1873,7 @@ feature: status\input | 0 | 1 | else | --------------+------------+------------+------------+ - not allocated |(do nothing)| alloc+swap | EINVAL | + not allocated |(do nothing)| alloc+swap |(do nothing)| --------------+------------+------------+------------+ allocated | free | swap | clear | --------------+------------+------------+------------+ |