diff options
Diffstat (limited to 'Documentation')
18 files changed, 374 insertions, 21 deletions
diff --git a/Documentation/devicetree/bindings/arm/arm,scpi.txt b/Documentation/devicetree/bindings/arm/arm,scpi.txt index 313dabdc14f9..faa4b44572e3 100644 --- a/Documentation/devicetree/bindings/arm/arm,scpi.txt +++ b/Documentation/devicetree/bindings/arm/arm,scpi.txt @@ -87,10 +87,33 @@ Required properties: implementation for the IDs to use. For Juno R0 and Juno R1 refer to [3]. +Power domain bindings for the power domains based on SCPI Message Protocol +------------------------------------------------------------ + +This binding uses the generic power domain binding[4]. + +PM domain providers +=================== + +Required properties: + - #power-domain-cells : Should be 1. Contains the device or the power + domain ID value used by SCPI commands. + - num-domains: Total number of power domains provided by SCPI. This is + needed as the SCPI message protocol lacks a mechanism to + query this information at runtime. + +PM domain consumers +=================== + +Required properties: + - power-domains : A phandle and PM domain specifier as defined by bindings of + the power controller specified by phandle. + [0] http://infocenter.arm.com/help/topic/com.arm.doc.dui0922b/index.html [1] Documentation/devicetree/bindings/clock/clock-bindings.txt [2] Documentation/devicetree/bindings/thermal/thermal.txt [3] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dui0922b/apas03s22.html +[4] Documentation/devicetree/bindings/power/power_domain.txt Example: @@ -144,6 +167,12 @@ scpi_protocol: scpi@2e000000 { compatible = "arm,scpi-sensors"; #thermal-sensor-cells = <1>; }; + + scpi_devpd: scpi-power-domains { + compatible = "arm,scpi-power-domains"; + num-domains = <2>; + #power-domain-cells = <1>; + }; }; cpu@0 { @@ -156,6 +185,7 @@ hdlcd@7ff60000 { ... reg = <0 0x7ff60000 0 0x1000>; clocks = <&scpi_clk 4>; + power-domains = <&scpi_devpd 1>; }; thermal-zones { @@ -186,3 +216,7 @@ The thermal-sensors property in the soc_thermal node uses the temperature sensor provided by SCP firmware to setup a thermal zone. The ID "3" is the sensor identifier for the temperature sensor as used by the firmware. + +The num-domains property in scpi-power-domains domain specifies that +SCPI provides 2 power domains. The hdlcd node uses the power domain with +domain ID 1. diff --git a/Documentation/devicetree/bindings/bus/nvidia,tegra210-aconnect.txt b/Documentation/devicetree/bindings/bus/nvidia,tegra210-aconnect.txt new file mode 100644 index 000000000000..7ff13be1750b --- /dev/null +++ b/Documentation/devicetree/bindings/bus/nvidia,tegra210-aconnect.txt @@ -0,0 +1,45 @@ +NVIDIA Tegra ACONNECT Bus + +The Tegra ACONNECT bus is an AXI switch which is used to connnect various +components inside the Audio Processing Engine (APE). All CPU accesses to +the APE subsystem go through the ACONNECT via an APB to AXI wrapper. + +Required properties: +- compatible: Must be "nvidia,tegra210-aconnect". +- clocks: Must contain the entries for the APE clock (TEGRA210_CLK_APE), + and APE interface clock (TEGRA210_CLK_APB2APE). +- clock-names: Must contain the names "ape" and "apb2ape" for the corresponding + 'clocks' entries. +- power-domains: Must contain a phandle that points to the audio powergate + (namely 'aud') for Tegra210. +- #address-cells: The number of cells used to represent physical base addresses + in the aconnect address space. Should be 1. +- #size-cells: The number of cells used to represent the size of an address + range in the aconnect address space. Should be 1. +- ranges: Mapping of the aconnect address space to the CPU address space. + +All devices accessed via the ACONNNECT are described by child-nodes. + +Example: + + aconnect@702c0000 { + compatible = "nvidia,tegra210-aconnect"; + clocks = <&tegra_car TEGRA210_CLK_APE>, + <&tegra_car TEGRA210_CLK_APB2APE>; + clock-names = "ape", "apb2ape"; + power-domains = <&pd_audio>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x702c0000 0x0 0x702c0000 0x00040000>; + + status = "disabled"; + + child1 { + ... + }; + + child2 { + ... + }; + }; diff --git a/Documentation/devicetree/bindings/clock/clps711x-clock.txt b/Documentation/devicetree/bindings/clock/clps711x-clock.txt index ce5a7476f05d..f1bd53f79d91 100644 --- a/Documentation/devicetree/bindings/clock/clps711x-clock.txt +++ b/Documentation/devicetree/bindings/clock/clps711x-clock.txt @@ -1,7 +1,7 @@ * Clock bindings for the Cirrus Logic CLPS711X CPUs Required properties: -- compatible : Shall contain "cirrus,clps711x-clk". +- compatible : Shall contain "cirrus,ep7209-clk". - reg : Address of the internal register set. - startup-frequency: Factory set CPU startup frequency in HZ. - #clock-cells : Should be <1>. @@ -13,7 +13,7 @@ for the full list of CLPS711X clock IDs. Example: clks: clks@80000000 { #clock-cells = <1>; - compatible = "cirrus,ep7312-clk", "cirrus,clps711x-clk"; + compatible = "cirrus,ep7312-clk", "cirrus,ep7209-clk"; reg = <0x80000000 0xc000>; startup-frequency = <73728000>; }; diff --git a/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt b/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt index d685be898d0c..e9c65746e2f1 100644 --- a/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt +++ b/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt @@ -1,7 +1,7 @@ * Currus Logic CLPS711X Framebuffer Required properties: -- compatible: Shall contain "cirrus,clps711x-fb". +- compatible: Shall contain "cirrus,ep7209-fb". - reg : Physical base address and length of the controller's registers + location and size of the framebuffer memory. - clocks : phandle + clock specifier pair of the FB reference clock. @@ -18,7 +18,7 @@ Optional properties: Example: fb: fb@800002c0 { - compatible = "cirrus,ep7312-fb", "cirrus,clps711x-fb"; + compatible = "cirrus,ep7312-fb", "cirrus,ep7209-fb"; reg = <0x800002c0 0xd44>, <0x60000000 0xc000>; clocks = <&clks 2>; lcd-supply = <®5v0>; diff --git a/Documentation/devicetree/bindings/input/clps711x-keypad.txt b/Documentation/devicetree/bindings/input/clps711x-keypad.txt index e68d2bbc6c07..3eed8819d05d 100644 --- a/Documentation/devicetree/bindings/input/clps711x-keypad.txt +++ b/Documentation/devicetree/bindings/input/clps711x-keypad.txt @@ -1,7 +1,7 @@ * Cirrus Logic CLPS711X matrix keypad device tree bindings Required Properties: -- compatible: Shall contain "cirrus,clps711x-keypad". +- compatible: Shall contain "cirrus,ep7209-keypad". - row-gpios: List of GPIOs used as row lines. - poll-interval: Poll interval time in milliseconds. - linux,keymap: The definition can be found at @@ -12,7 +12,7 @@ Optional Properties: Example: keypad { - compatible = "cirrus,ep7312-keypad", "cirrus,clps711x-keypad"; + compatible = "cirrus,ep7312-keypad", "cirrus,ep7209-keypad"; autorepeat; poll-interval = <120>; row-gpios = <&porta 0 0>, diff --git a/Documentation/devicetree/bindings/interrupt-controller/cirrus,clps711x-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/cirrus,clps711x-intc.txt index 759339c34e4f..969b4582ec60 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/cirrus,clps711x-intc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/cirrus,clps711x-intc.txt @@ -2,7 +2,7 @@ Cirrus Logic CLPS711X Interrupt Controller Required properties: -- compatible: Should be "cirrus,clps711x-intc". +- compatible: Should be "cirrus,ep7209-intc". - reg: Specifies base physical address of the registers set. - interrupt-controller: Identifies the node as an interrupt controller. - #interrupt-cells: Specifies the number of cells needed to encode an @@ -34,7 +34,7 @@ ID Name Description Example: intc: interrupt-controller { - compatible = "cirrus,clps711x-intc"; + compatible = "cirrus,ep7312-intc", "cirrus,ep7209-intc"; reg = <0x80000000 0x4000>; interrupt-controller; #interrupt-cells = <1>; diff --git a/Documentation/devicetree/bindings/media/nokia,n900-ir b/Documentation/devicetree/bindings/media/nokia,n900-ir new file mode 100644 index 000000000000..13a18ce37dd1 --- /dev/null +++ b/Documentation/devicetree/bindings/media/nokia,n900-ir @@ -0,0 +1,20 @@ +Device-Tree bindings for LIRC TX driver for Nokia N900(RX51) + +Required properties: + - compatible: should be "nokia,n900-ir". + - pwms: specifies PWM used for IR signal transmission. + +Example node: + + pwm9: dmtimer-pwm@9 { + compatible = "ti,omap-dmtimer-pwm"; + ti,timers = <&timer9>; + ti,clock-source = <0x00>; /* timer_sys_ck */ + #pwm-cells = <3>; + }; + + ir: n900-ir { + compatible = "nokia,n900-ir"; + + pwms = <&pwm9 0 26316 0>; /* 38000 Hz */ + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt b/Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt new file mode 100644 index 000000000000..9bb5f57e2066 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt @@ -0,0 +1,136 @@ +* Device tree bindings for Atmel EBI + +The External Bus Interface (EBI) controller is a bus where you can connect +asynchronous (NAND, NOR, SRAM, ....) and synchronous memories (SDR/DDR SDRAMs). +The EBI provides a glue-less interface to asynchronous memories through the SMC +(Static Memory Controller). + +Required properties: + +- compatible: "atmel,at91sam9260-ebi" + "atmel,at91sam9261-ebi" + "atmel,at91sam9263-ebi0" + "atmel,at91sam9263-ebi1" + "atmel,at91sam9rl-ebi" + "atmel,at91sam9g45-ebi" + "atmel,at91sam9x5-ebi" + "atmel,sama5d3-ebi" + +- reg: Contains offset/length value for EBI memory mapping. + This property might contain several entries if the EBI + memory range is not contiguous + +- #address-cells: Must be 2. + The first cell encodes the CS. + The second cell encode the offset into the CS memory + range. + +- #size-cells: Must be set to 1. + +- ranges: Encodes CS to memory region association. + +- clocks: Clock feeding the EBI controller. + See clock-bindings.txt + +Children device nodes are representing device connected to the EBI bus. + +Required device node properties: + +- reg: Contains the chip-select id, the offset and the length + of the memory region requested by the device. + +EBI bus configuration will be defined directly in the device subnode. + +Optional EBI/SMC properties: + +- atmel,smc-bus-width: width of the asynchronous device's data bus + 8, 16 or 32. + Default to 8 when undefined. + +- atmel,smc-byte-access-type "write" or "select" (see Atmel datasheet). + Default to "select" when undefined. + +- atmel,smc-read-mode "nrd" or "ncs". + Default to "ncs" when undefined. + +- atmel,smc-write-mode "nwe" or "ncs". + Default to "ncs" when undefined. + +- atmel,smc-exnw-mode "disabled", "frozen" or "ready". + Default to "disabled" when undefined. + +- atmel,smc-page-mode enable page mode if present. The provided value + defines the page size (supported values: 4, 8, + 16 and 32). + +- atmel,smc-tdf-mode: "normal" or "optimized". When set to + "optimized" the data float time is optimized + depending on the next device being accessed + (next device setup time is subtracted to the + current device data float time). + Default to "normal" when undefined. + +If at least one atmel,smc- property is defined the following SMC timing +properties become mandatory. In the other hand, if none of the atmel,smc- +properties are specified, we assume that the EBI bus configuration will be +handled by the sub-device driver, and none of those properties should be +defined. + +All the timings are expressed in nanoseconds (see Atmel datasheet for a full +description). + +- atmel,smc-ncs-rd-setup-ns +- atmel,smc-nrd-setup-ns +- atmel,smc-ncs-wr-setup-ns +- atmel,smc-nwe-setup-ns +- atmel,smc-ncs-rd-pulse-ns +- atmel,smc-nrd-pulse-ns +- atmel,smc-ncs-wr-pulse-ns +- atmel,smc-nwe-pulse-ns +- atmel,smc-nwe-cycle-ns +- atmel,smc-nrd-cycle-ns +- atmel,smc-tdf-ns + +Example: + + ebi: ebi@10000000 { + compatible = "atmel,sama5d3-ebi"; + #address-cells = <2>; + #size-cells = <1>; + atmel,smc = <&hsmc>; + atmel,matrix = <&matrix>; + reg = <0x10000000 0x10000000 + 0x40000000 0x30000000>; + ranges = <0x0 0x0 0x10000000 0x10000000 + 0x1 0x0 0x40000000 0x10000000 + 0x2 0x0 0x50000000 0x10000000 + 0x3 0x0 0x60000000 0x10000000>; + clocks = <&mck>; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ebi_addr>; + + nor: flash@0,0 { + compatible = "cfi-flash"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x0 0x0 0x1000000>; + bank-width = <2>; + + atmel,smc-read-mode = "nrd"; + atmel,smc-write-mode = "nwe"; + atmel,smc-bus-width = <16>; + atmel,smc-ncs-rd-setup-ns = <0>; + atmel,smc-ncs-wr-setup-ns = <0>; + atmel,smc-nwe-setup-ns = <8>; + atmel,smc-nrd-setup-ns = <16>; + atmel,smc-ncs-rd-pulse-ns = <84>; + atmel,smc-ncs-wr-pulse-ns = <84>; + atmel,smc-nrd-pulse-ns = <76>; + atmel,smc-nwe-pulse-ns = <76>; + atmel,smc-nrd-cycle-ns = <107>; + atmel,smc-nwe-cycle-ns = <84>; + atmel,smc-tdf-ns = <16>; + }; + }; + diff --git a/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt b/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt index a183db48f910..c0b2028238d6 100644 --- a/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt @@ -1,15 +1,14 @@ * Cirris Logic CLPS711X PWM controller Required properties: -- compatible: Shall contain "cirrus,clps711x-pwm". +- compatible: Shall contain "cirrus,ep7209-pwm". - reg: Physical base address and length of the controller's registers. - clocks: phandle + clock specifier pair of the PWM reference clock. - #pwm-cells: Should be 1. The cell specifies the index of the channel. Example: pwm: pwm@80000400 { - compatible = "cirrus,ep7312-pwm", - "cirrus,clps711x-pwm"; + compatible = "cirrus,ep7312-pwm", "cirrus,ep7209-pwm"; reg = <0x80000400 0x4>; clocks = <&clks 8>; #pwm-cells = <1>; diff --git a/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt b/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt index 5befb538db95..2e53324fb720 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt @@ -9,6 +9,10 @@ Required properties: Optional properties: - ti,prescaler: Should be a value between 0 and 7, see the timers datasheet +- ti,clock-source: Set dmtimer parent clock, values between 0 and 2: + - 0x00 - high-frequency system clock (timer_sys_ck) + - 0x01 - 32-kHz always-on clock (timer_32k_ck) + - 0x02 - external clock (timer_ext_ck, OMAP2 only) Example: pwm9: dmtimer-pwm@9 { diff --git a/Documentation/devicetree/bindings/reset/amlogic,meson-reset.txt b/Documentation/devicetree/bindings/reset/amlogic,meson-reset.txt new file mode 100644 index 000000000000..e746b631793a --- /dev/null +++ b/Documentation/devicetree/bindings/reset/amlogic,meson-reset.txt @@ -0,0 +1,18 @@ +Amlogic Meson SoC Reset Controller +======================================= + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +Required properties: +- compatible: Should be "amlogic,meson8b-reset" or "amlogic,meson-gxbb-reset" +- reg: should contain the register address base +- #reset-cells: 1, see below + +example: + +reset: reset-controller { + compatible = "amlogic,meson-gxbb-reset"; + reg = <0x0 0x04404 0x0 0x20>; + #reset-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt b/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt index e0b185a944ba..c25da39df707 100644 --- a/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt +++ b/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt @@ -8,7 +8,9 @@ The reset controller registers are part of the system-ctl block on hi6220 SoC. Required properties: -- compatible: may be "hisilicon,hi6220-sysctrl" +- compatible: should be one of the following: + - "hisilicon,hi6220-sysctrl", "syscon" : For peripheral reset controller. + - "hisilicon,hi6220-mediactrl", "syscon" : For media reset controller. - reg: should be register base and length as documented in the datasheet - #reset-cells: 1, see below diff --git a/Documentation/devicetree/bindings/reset/ti-syscon-reset.txt b/Documentation/devicetree/bindings/reset/ti-syscon-reset.txt new file mode 100644 index 000000000000..164c7f34c451 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/ti-syscon-reset.txt @@ -0,0 +1,91 @@ +TI SysCon Reset Controller +======================= + +Almost all SoCs have hardware modules that require reset control in addition +to clock and power control for their functionality. The reset control is +typically provided by means of memory-mapped I/O registers. These registers are +sometimes a part of a larger register space region implementing various +functionalities. This register range is best represented as a syscon node to +allow multiple entities to access their relevant registers in the common +register space. + +A SysCon Reset Controller node defines a device that uses a syscon node +and provides reset management functionality for various hardware modules +present on the SoC. + +SysCon Reset Controller Node +============================ +Each of the reset provider/controller nodes should be a child of a syscon +node and have the following properties. + +Required properties: +-------------------- + - compatible : Should be, + "ti,k2e-pscrst" + "ti,k2l-pscrst" + "ti,k2hk-pscrst" + "ti,syscon-reset" + - #reset-cells : Should be 1. Please see the reset consumer node below + for usage details + - ti,reset-bits : Contains the reset control register information + Should contain 7 cells for each reset exposed to + consumers, defined as: + Cell #1 : offset of the reset assert control + register from the syscon register base + Cell #2 : bit position of the reset in the reset + assert control register + Cell #3 : offset of the reset deassert control + register from the syscon register base + Cell #4 : bit position of the reset in the reset + deassert control register + Cell #5 : offset of the reset status register + from the syscon register base + Cell #6 : bit position of the reset in the + reset status register + Cell #7 : Flags used to control reset behavior, + availible flags defined in the DT include + file <dt-bindings/reset/ti-syscon.h> + +SysCon Reset Consumer Nodes +=========================== +Each of the reset consumer nodes should have the following properties, +in addition to their own properties. + +Required properties: +-------------------- + - resets : A phandle to the reset controller node and an index number + to a reset specifier as defined above. + +Please also refer to Documentation/devicetree/bindings/reset/reset.txt for +common reset controller usage by consumers. + +Example: +-------- +The following example demonstrates a syscon node, the reset controller node +using the syscon node, and a consumer (a DSP device) on the TI Keystone 2 +Edison SoC. + +/ { + soc { + psc: power-sleep-controller@02350000 { + compatible = "syscon", "simple-mfd"; + reg = <0x02350000 0x1000>; + + pscrst: psc-reset { + compatible = "ti,k2e-pscrst", "ti,syscon-reset"; + #reset-cells = <1>; + + ti,reset-bits = < + 0xa3c 8 0xa3c 8 0x83c 8 (ASSERT_SET|DEASSERT_CLEAR|STATUS_SET) /* 0: pcrst-dsp0 */ + 0xa40 5 0xa44 3 0 0 (ASSERT_SET|DEASSERT_CLEAR|STATUS_NONE) /* 1: pcrst-example */ + >; + }; + }; + + dsp0: dsp0 { + ... + resets = <&pscrst 0>; + ... + }; + }; +}; diff --git a/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt b/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt index caaeb2583579..07013fa60a48 100644 --- a/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt +++ b/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt @@ -1,7 +1,7 @@ * Cirrus Logic CLPS711X Universal Asynchronous Receiver/Transmitter (UART) Required properties: -- compatible: Should be "cirrus,clps711x-uart". +- compatible: Should be "cirrus,ep7209-uart". - reg: Address and length of the register set for the device. - interrupts: Should contain UART TX and RX interrupt. - clocks: Should contain UART core clock number. @@ -20,7 +20,7 @@ Example: }; uart1: uart@80000480 { - compatible = "cirrus,clps711x-uart"; + compatible = "cirrus,ep7312-uart","cirrus,ep7209-uart"; reg = <0x80000480 0x80>; interrupts = <12 13>; clocks = <&clks 11>; diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt index 5cc82b8353d8..af9ca37221ce 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt @@ -68,7 +68,7 @@ important. Value type: <u32> Definition: must be 2 - denoting the bit in the entry and IRQ flags -- #qcom,state-cells: +- #qcom,smem-state-cells: Usage: required for outgoing entries Value type: <u32> Definition: must be 1 - denoting the bit in the entry @@ -92,7 +92,7 @@ wcnss-smp2p { wcnss_smp2p_out: master-kernel { qcom,entry-name = "master-kernel"; - #qcom,state-cells = <1>; + #qcom,smem-state-cells = <1>; }; wcnss_smp2p_in: slave-kernel { diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt index a6634c70850d..2993b5a97dd6 100644 --- a/Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt @@ -51,7 +51,7 @@ important. Definition: specifies the offset, in words, of the first bit for this entry -- #qcom,state-cells: +- #qcom,smem-state-cells: Usage: required for local entry Value type: <u32> Definition: must be 1 - denotes bit number @@ -91,7 +91,7 @@ smsm { apps_smsm: apps@0 { reg = <0>; - #qcom,state-cells = <1>; + #qcom,smem-state-cells = <1>; }; wcnss_smsm: wcnss@7 { diff --git a/Documentation/devicetree/bindings/timer/cirrus,clps711x-timer.txt b/Documentation/devicetree/bindings/timer/cirrus,clps711x-timer.txt index cd55b52548e4..d4c62e7b1714 100644 --- a/Documentation/devicetree/bindings/timer/cirrus,clps711x-timer.txt +++ b/Documentation/devicetree/bindings/timer/cirrus,clps711x-timer.txt @@ -1,7 +1,7 @@ * Cirrus Logic CLPS711X Timer Counter Required properties: -- compatible: Shall contain "cirrus,clps711x-timer". +- compatible: Shall contain "cirrus,ep7209-timer". - reg : Address and length of the register set. - interrupts: The interrupt number of the timer. - clocks : phandle of timer reference clock. @@ -15,14 +15,14 @@ Example: }; timer1: timer@80000300 { - compatible = "cirrus,ep7312-timer", "cirrus,clps711x-timer"; + compatible = "cirrus,ep7312-timer", "cirrus,ep7209-timer"; reg = <0x80000300 0x4>; interrupts = <8>; clocks = <&clks 5>; }; timer2: timer@80000340 { - compatible = "cirrus,ep7312-timer", "cirrus,clps711x-timer"; + compatible = "cirrus,ep7312-timer", "cirrus,ep7209-timer"; reg = <0x80000340 0x4>; interrupts = <9>; clocks = <&clks 6>; diff --git a/Documentation/driver-model/devres.txt b/Documentation/driver-model/devres.txt index 589296bdc133..b0d775d28e97 100644 --- a/Documentation/driver-model/devres.txt +++ b/Documentation/driver-model/devres.txt @@ -352,6 +352,10 @@ REGULATOR devm_regulator_put() devm_regulator_register() +RESET + devm_reset_control_get() + devm_reset_controller_register() + SLAVE DMA ENGINE devm_acpi_dma_controller_register() |