summaryrefslogtreecommitdiff
path: root/Documentation
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation')
-rw-r--r--Documentation/devicetree/bindings/serial/bcm63xx-uart.txt30
-rw-r--r--Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt10
-rw-r--r--Documentation/devicetree/bindings/serial/of-serial.txt1
-rw-r--r--Documentation/devicetree/bindings/serial/pl011.txt20
-rw-r--r--Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt69
-rw-r--r--Documentation/devicetree/bindings/serial/renesas,sci-serial.txt9
-rw-r--r--Documentation/devicetree/bindings/serial/sirf-uart.txt16
-rw-r--r--Documentation/serial/driver6
8 files changed, 129 insertions, 32 deletions
diff --git a/Documentation/devicetree/bindings/serial/bcm63xx-uart.txt b/Documentation/devicetree/bindings/serial/bcm63xx-uart.txt
new file mode 100644
index 000000000000..5c52e5eef16d
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/bcm63xx-uart.txt
@@ -0,0 +1,30 @@
+* BCM63xx UART
+
+Required properties:
+
+- compatible: "brcm,bcm6345-uart"
+
+- reg: The base address of the UART register bank.
+
+- interrupts: A single interrupt specifier.
+
+- clocks: Clock driving the hardware; used to figure out the baud rate
+ divisor.
+
+Example:
+
+ uart0: serial@14e00520 {
+ compatible = "brcm,bcm6345-uart";
+ reg = <0x14e00520 0x18>;
+ interrupt-parent = <&periph_intc>;
+ interrupts = <2>;
+ clocks = <&periph_clk>;
+ };
+
+ clocks {
+ periph_clk: periph_clk@0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <54000000>;
+ };
+ };
diff --git a/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt b/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt
index 59a40f18d551..7c408c87e613 100644
--- a/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt
+++ b/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt
@@ -11,8 +11,13 @@ Required properties:
- dma-names: "rx" for RX channel, "tx" for TX channel.
Optional properties:
-- fsl,uart-has-rtscts : Indicate the UART has RTS and CTS lines,
+- fsl,uart-has-rtscts : Indicate the UART has RTS and CTS lines
+ for hardware flow control,
it also means you enable the DMA support for this UART.
+- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD
+ line respectively. It will use specified PIO instead of the peripheral
+ function pin for the USART feature.
+ If unsure, don't specify this property.
Example:
auart0: serial@8006a000 {
@@ -21,6 +26,9 @@ auart0: serial@8006a000 {
interrupts = <112>;
dmas = <&dma_apbx 8>, <&dma_apbx 9>;
dma-names = "rx", "tx";
+ cts-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ dsr-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+ dcd-gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
};
Note: Each auart port should have an alias correctly numbered in "aliases"
diff --git a/Documentation/devicetree/bindings/serial/of-serial.txt b/Documentation/devicetree/bindings/serial/of-serial.txt
index 8c4fd0332028..b52b98234b9b 100644
--- a/Documentation/devicetree/bindings/serial/of-serial.txt
+++ b/Documentation/devicetree/bindings/serial/of-serial.txt
@@ -10,6 +10,7 @@ Required properties:
- "ns16850"
- "nvidia,tegra20-uart"
- "nxp,lpc3220-uart"
+ - "ralink,rt2880-uart"
- "ibm,qpace-nwp-serial"
- "altr,16550-FIFO32"
- "altr,16550-FIFO64"
diff --git a/Documentation/devicetree/bindings/serial/pl011.txt b/Documentation/devicetree/bindings/serial/pl011.txt
index 52464918cfe2..ba3ecb8cb5a1 100644
--- a/Documentation/devicetree/bindings/serial/pl011.txt
+++ b/Documentation/devicetree/bindings/serial/pl011.txt
@@ -6,23 +6,35 @@ Required properties:
- interrupts: exactly one interrupt specifier
Optional properties:
-- pinctrl: When present, must have one state named "default",
+- pinctrl:
+ When present, must have one state named "default",
and may contain a second name named "sleep". The former
state sets up pins for ordinary operation whereas
the latter state will put the associated pins to sleep
when the UART is unused
-- clocks: When present, the first clock listed must correspond to
+- clocks:
+ When present, the first clock listed must correspond to
the clock named UARTCLK on the IP block, i.e. the clock
to the external serial line, whereas the second clock
must correspond to the PCLK clocking the internal logic
of the block. Just listing one clock (the first one) is
deprecated.
-- clocks-names: When present, the first clock listed must be named
+- clocks-names:
+ When present, the first clock listed must be named
"uartclk" and the second clock listed must be named
"apb_pclk"
-- dmas: When present, may have one or two dma channels.
+- dmas:
+ When present, may have one or two dma channels.
The first one must be named "rx", the second one
must be named "tx".
+- auto-poll:
+ Enables polling when using RX DMA.
+- poll-rate-ms:
+ Rate at which poll occurs when auto-poll is set,
+ default 100ms.
+- poll-timeout-ms:
+ Poll timeout when auto-poll is set, default
+ 3000ms.
See also bindings/arm/primecell.txt
diff --git a/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt
index ffa5b784c66e..a2114c217376 100644
--- a/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt
+++ b/Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt
@@ -27,27 +27,52 @@ Optional properties:
- dmas: Should contain dma specifiers for transmit and receive channels
- dma-names: Should contain "tx" for transmit and "rx" for receive channels
+Note: Aliases may be defined to ensure the correct ordering of the UARTs.
+The alias serialN will result in the UART being assigned port N. If any
+serialN alias exists, then an alias must exist for each enabled UART. The
+serialN aliases should be in a .dts file instead of in a .dtsi file.
+
Examples:
-A uartdm v1.4 device with dma capabilities.
-
-serial@f991e000 {
- compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
- reg = <0xf991e000 0x1000>;
- interrupts = <0 108 0x0>;
- clocks = <&blsp1_uart2_apps_cxc>, <&blsp1_ahb_cxc>;
- clock-names = "core", "iface";
- dmas = <&dma0 0>, <&dma0 1>;
- dma-names = "tx", "rx";
-};
-
-A uartdm v1.3 device without dma capabilities and part of a GSBI complex.
-
-serial@19c40000 {
- compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
- reg = <0x19c40000 0x1000>,
- <0x19c00000 0x1000>;
- interrupts = <0 195 0x0>;
- clocks = <&gsbi5_uart_cxc>, <&gsbi5_ahb_cxc>;
- clock-names = "core", "iface";
-};
+- A uartdm v1.4 device with dma capabilities.
+
+ serial@f991e000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0xf991e000 0x1000>;
+ interrupts = <0 108 0x0>;
+ clocks = <&blsp1_uart2_apps_cxc>, <&blsp1_ahb_cxc>;
+ clock-names = "core", "iface";
+ dmas = <&dma0 0>, <&dma0 1>;
+ dma-names = "tx", "rx";
+ };
+
+- A uartdm v1.3 device without dma capabilities and part of a GSBI complex.
+
+ serial@19c40000 {
+ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+ reg = <0x19c40000 0x1000>,
+ <0x19c00000 0x1000>;
+ interrupts = <0 195 0x0>;
+ clocks = <&gsbi5_uart_cxc>, <&gsbi5_ahb_cxc>;
+ clock-names = "core", "iface";
+ };
+
+- serialN alias.
+
+ aliases {
+ serial0 = &uarta;
+ serial1 = &uartc;
+ serial2 = &uartb;
+ };
+
+ uarta: serial@12490000 {
+ status = "ok";
+ };
+
+ uartb: serial@16340000 {
+ status = "ok";
+ };
+
+ uartc: serial@1a240000 {
+ status = "ok";
+ };
diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt
index b3556609a06f..ae73bb0e9ad9 100644
--- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt
+++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt
@@ -4,8 +4,7 @@ Required properties:
- compatible: Must contain one of the following:
- - "renesas,scifa-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFA compatible UART.
- - "renesas,scifb-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFB compatible UART.
+ - "renesas,scif-r7s72100" for R7S72100 (RZ/A1H) SCIF compatible UART.
- "renesas,scifa-r8a73a4" for R8A73A4 (R-Mobile APE6) SCIFA compatible UART.
- "renesas,scifb-r8a73a4" for R8A73A4 (R-Mobile APE6) SCIFB compatible UART.
- "renesas,scifa-r8a7740" for R8A7740 (R-Mobile A1) SCIFA compatible UART.
@@ -20,6 +19,12 @@ Required properties:
- "renesas,scifa-r8a7791" for R8A7791 (R-Car M2) SCIFA compatible UART.
- "renesas,scifb-r8a7791" for R8A7791 (R-Car M2) SCIFB compatible UART.
- "renesas,hscif-r8a7791" for R8A7791 (R-Car M2) HSCIF compatible UART.
+ - "renesas,scif-r8a7794" for R8A7794 (R-Car E2) SCIF compatible UART.
+ - "renesas,scifa-r8a7794" for R8A7794 (R-Car E2) SCIFA compatible UART.
+ - "renesas,scifb-r8a7794" for R8A7794 (R-Car E2) SCIFB compatible UART.
+ - "renesas,hscif-r8a7794" for R8A7794 (R-Car E2) HSCIF compatible UART.
+ - "renesas,scifa-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFA compatible UART.
+ - "renesas,scifb-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFB compatible UART.
- "renesas,scif" for generic SCIF compatible UART.
- "renesas,scifa" for generic SCIFA compatible UART.
- "renesas,scifb" for generic SCIFB compatible UART.
diff --git a/Documentation/devicetree/bindings/serial/sirf-uart.txt b/Documentation/devicetree/bindings/serial/sirf-uart.txt
index a2dfc6522a91..3acdd969edf1 100644
--- a/Documentation/devicetree/bindings/serial/sirf-uart.txt
+++ b/Documentation/devicetree/bindings/serial/sirf-uart.txt
@@ -1,7 +1,9 @@
* CSR SiRFprimaII/atlasVI Universal Synchronous Asynchronous Receiver/Transmitter *
Required properties:
-- compatible : Should be "sirf,prima2-uart" or "sirf, prima2-usp-uart"
+- compatible : Should be "sirf,prima2-uart", "sirf, prima2-usp-uart",
+ "sirf,marco-uart" or "sirf,marco-bt-uart" which means
+ uart located in BT module and used for BT.
- reg : Offset and length of the register set for the device
- interrupts : Should contain uart interrupt
- fifosize : Should define hardware rx/tx fifo size
@@ -31,3 +33,15 @@ usp@b0090000 {
rts-gpios = <&gpio 15 0>;
cts-gpios = <&gpio 46 0>;
};
+
+for uart use in BT module,
+uart6: uart@11000000 {
+ cell-index = <6>;
+ compatible = "sirf,marco-bt-uart", "sirf,marco-uart";
+ reg = <0x11000000 0x1000>;
+ interrupts = <0 100 0>;
+ clocks = <&clks 138>, <&clks 140>, <&clks 141>;
+ clock-names = "uart", "general", "noc";
+ fifosize = <128>;
+ status = "disabled";
+}
diff --git a/Documentation/serial/driver b/Documentation/serial/driver
index ba64e4b892e9..c415b0ef4493 100644
--- a/Documentation/serial/driver
+++ b/Documentation/serial/driver
@@ -59,7 +59,9 @@ The core driver uses the info->tmpbuf_sem lock to prevent multi-threaded
access to the info->tmpbuf bouncebuffer used for port writes.
The port_sem semaphore is used to protect against ports being added/
-removed or reconfigured at inappropriate times.
+removed or reconfigured at inappropriate times. Since v2.6.27, this
+semaphore has been the 'mutex' member of the tty_port struct, and
+commonly referred to as the port mutex (or port->mutex).
uart_ops
@@ -248,7 +250,7 @@ hardware.
Other flags may be used (eg, xon/xoff characters) if your
hardware supports hardware "soft" flow control.
- Locking: none.
+ Locking: caller holds port->mutex
Interrupts: caller dependent.
This call must not sleep