diff options
Diffstat (limited to 'Documentation')
-rw-r--r-- | Documentation/ABI/testing/sysfs-bus-iio | 54 | ||||
-rw-r--r-- | Documentation/ABI/testing/sysfs-bus-iio-frequency-ad9523 | 37 | ||||
-rw-r--r-- | Documentation/ABI/testing/sysfs-bus-iio-frequency-adf4350 | 21 | ||||
-rw-r--r-- | Documentation/ABI/testing/sysfs-bus-iio-light-lm3533-als | 61 | ||||
-rw-r--r-- | Documentation/ramoops.txt | 39 |
5 files changed, 186 insertions, 26 deletions
diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio index cfedf63cce15..2f06d40fe07d 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio +++ b/Documentation/ABI/testing/sysfs-bus-iio @@ -40,9 +40,9 @@ Contact: linux-iio@vger.kernel.org Description: Some devices have internal clocks. This parameter sets the resulting sampling frequency. In many devices this - parameter has an effect on input filters etc rather than + parameter has an effect on input filters etc. rather than simply controlling when the input is sampled. As this - effects datardy triggers, hardware buffers and the sysfs + effects data ready triggers, hardware buffers and the sysfs direct access interfaces, it may be found in any of the relevant directories. If it effects all of the above then it is to be found in the base device directory. @@ -74,7 +74,7 @@ What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_supply_raw KernelVersion: 2.6.35 Contact: linux-iio@vger.kernel.org Description: - Raw (unscaled no bias removal etc) voltage measurement from + Raw (unscaled no bias removal etc.) voltage measurement from channel Y. In special cases where the channel does not correspond to externally available input one of the named versions may be used. The number must always be specified and @@ -118,11 +118,11 @@ What: /sys/bus/iio/devices/iio:deviceX/in_temp_z_raw KernelVersion: 2.6.35 Contact: linux-iio@vger.kernel.org Description: - Raw (unscaled no bias removal etc) temperature measurement. + Raw (unscaled no bias removal etc.) temperature measurement. If an axis is specified it generally means that the temperature sensor is associated with one part of a compound device (e.g. a gyroscope axis). Units after application of scale and offset - are milli degrees Celsuis. + are milli degrees Celsius. What: /sys/bus/iio/devices/iio:deviceX/in_tempX_input KernelVersion: 2.6.38 @@ -148,10 +148,9 @@ KernelVersion: 2.6.35 Contact: linux-iio@vger.kernel.org Description: Angular velocity about axis x, y or z (may be arbitrarily - assigned) Data converted by application of offset then scale to - radians per second. Has all the equivalent parameters as - per voltageY. Units after application of scale and offset are - radians per second. + assigned). Has all the equivalent parameters as per voltageY. + Units after application of scale and offset are radians per + second. What: /sys/bus/iio/devices/iio:deviceX/in_incli_x_raw What: /sys/bus/iio/devices/iio:deviceX/in_incli_y_raw @@ -161,7 +160,7 @@ Contact: linux-iio@vger.kernel.org Description: Inclination raw reading about axis x, y or z (may be arbitrarily assigned). Data converted by application of offset - and scale to Degrees. + and scale to degrees. What: /sys/bus/iio/devices/iio:deviceX/in_magn_x_raw What: /sys/bus/iio/devices/iio:deviceX/in_magn_y_raw @@ -203,7 +202,7 @@ Contact: linux-iio@vger.kernel.org Description: If known for a device, offset to be added to <type>[Y]_raw prior to scaling by <type>[Y]_scale in order to obtain value in the - <type> units as specified in <type>[y]_raw documentation. + <type> units as specified in <type>[Y]_raw documentation. Not present if the offset is always 0 or unknown. If Y or axis <x|y|z> is not present, then the offset applies to all in channels of <type>. @@ -249,7 +248,7 @@ What: /sys/bus/iio/devices/iio:deviceX/in_proximity0_calibbias KernelVersion: 2.6.35 Contact: linux-iio@vger.kernel.org Description: - Hardware applied calibration offset. (assumed to fix production + Hardware applied calibration offset (assumed to fix production inaccuracies). What /sys/bus/iio/devices/iio:deviceX/in_voltageY_calibscale @@ -266,7 +265,7 @@ what /sys/bus/iio/devices/iio:deviceX/in_proximity0_calibscale KernelVersion: 2.6.35 Contact: linux-iio@vger.kernel.org Description: - Hardware applied calibration scale factor. (assumed to fix + Hardware applied calibration scale factor (assumed to fix production inaccuracies). If shared across all channels, <type>_calibscale is used. @@ -276,10 +275,10 @@ What: /sys/.../iio:deviceX/in_voltage-voltage_scale_available What: /sys/.../iio:deviceX/out_voltageX_scale_available What: /sys/.../iio:deviceX/out_altvoltageX_scale_available What: /sys/.../iio:deviceX/in_capacitance_scale_available -KernelVersion: 2.635 +KernelVersion: 2.6.35 Contact: linux-iio@vger.kernel.org Description: - If a discrete set of scale values are available, they + If a discrete set of scale values is available, they are listed in this attribute. What /sys/bus/iio/devices/iio:deviceX/out_voltageY_hardwaregain @@ -330,9 +329,11 @@ Contact: linux-iio@vger.kernel.org Description: Specifies the output powerdown mode. DAC output stage is disconnected from the amplifier and - 1kohm_to_gnd: connected to ground via an 1kOhm resistor - 100kohm_to_gnd: connected to ground via an 100kOhm resistor - three_state: left floating + 1kohm_to_gnd: connected to ground via an 1kOhm resistor, + 6kohm_to_gnd: connected to ground via a 6kOhm resistor, + 20kohm_to_gnd: connected to ground via a 20kOhm resistor, + 100kohm_to_gnd: connected to ground via an 100kOhm resistor, + three_state: left floating. For a list of available output power down options read outX_powerdown_mode_available. If Y is not present the mode is shared across all outputs. @@ -355,9 +356,10 @@ KernelVersion: 2.6.38 Contact: linux-iio@vger.kernel.org Description: Writing 1 causes output Y to enter the power down mode specified - by the corresponding outY_powerdown_mode. Clearing returns to - normal operation. Y may be suppressed if all outputs are - controlled together. + by the corresponding outY_powerdown_mode. DAC output stage is + disconnected from the amplifier. Clearing returns to normal + operation. Y may be suppressed if all outputs are controlled + together. What: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY_frequency KernelVersion: 3.4.0 @@ -421,12 +423,12 @@ Description: different values, but the device can only enable both thresholds or neither. Note the driver will assume the last p events requested are - to be enabled where p is however many it supports (which may - vary depending on the exact set requested. So if you want to be + to be enabled where p is how many it supports (which may vary + depending on the exact set requested. So if you want to be sure you have set what you think you have, check the contents of these attributes after everything is configured. Drivers may have to buffer any parameters so that they are consistent when - a given event type is enabled a future point (and not those for + a given event type is enabled at a future point (and not those for whatever event was previously enabled). What: /sys/.../iio:deviceX/events/in_accel_x_roc_rising_en @@ -702,7 +704,7 @@ What: /sys/.../buffer/scan_elements/in_anglvel_type What: /sys/.../buffer/scan_elements/in_magn_type What: /sys/.../buffer/scan_elements/in_incli_type What: /sys/.../buffer/scan_elements/in_voltageY_type -What: /sys/.../buffer/scan_elements/in_voltage-in_type +What: /sys/.../buffer/scan_elements/in_voltage_type What: /sys/.../buffer/scan_elements/in_voltageY_supply_type What: /sys/.../buffer/scan_elements/in_timestamp_type KernelVersion: 2.6.37 @@ -723,7 +725,7 @@ Description: the buffer output value appropriately. The storagebits value also specifies the data alignment. So s48/64>>2 will be a signed 48 bit integer stored in a 64 bit location aligned to - a a64 bit boundary. To obtain the clean value, shift right 2 + a 64 bit boundary. To obtain the clean value, shift right 2 and apply a mask to zero the top 16 bits of the result. For other storage combinations this attribute will be extended appropriately. diff --git a/Documentation/ABI/testing/sysfs-bus-iio-frequency-ad9523 b/Documentation/ABI/testing/sysfs-bus-iio-frequency-ad9523 new file mode 100644 index 000000000000..2ce9c3f68eee --- /dev/null +++ b/Documentation/ABI/testing/sysfs-bus-iio-frequency-ad9523 @@ -0,0 +1,37 @@ +What: /sys/bus/iio/devices/iio:deviceX/pll2_feedback_clk_present +What: /sys/bus/iio/devices/iio:deviceX/pll2_reference_clk_present +What: /sys/bus/iio/devices/iio:deviceX/pll1_reference_clk_a_present +What: /sys/bus/iio/devices/iio:deviceX/pll1_reference_clk_b_present +What: /sys/bus/iio/devices/iio:deviceX/pll1_reference_clk_test_present +What: /sys/bus/iio/devices/iio:deviceX/vcxo_clk_present +KernelVersion: 3.4.0 +Contact: linux-iio@vger.kernel.org +Description: + Reading returns either '1' or '0'. + '1' means that the clock in question is present. + '0' means that the clock is missing. + +What: /sys/bus/iio/devices/iio:deviceX/pllY_locked +KernelVersion: 3.4.0 +Contact: linux-iio@vger.kernel.org +Description: + Reading returns either '1' or '0'. '1' means that the + pllY is locked. + +What: /sys/bus/iio/devices/iio:deviceX/store_eeprom +KernelVersion: 3.4.0 +Contact: linux-iio@vger.kernel.org +Description: + Writing '1' stores the current device configuration into + on-chip EEPROM. After power-up or chip reset the device will + automatically load the saved configuration. + +What: /sys/bus/iio/devices/iio:deviceX/sync_dividers +KernelVersion: 3.4.0 +Contact: linux-iio@vger.kernel.org +Description: + Writing '1' triggers the clock distribution synchronization + functionality. All dividers are reset and the channels start + with their predefined phase offsets (out_altvoltageY_phase). + Writing this file has the effect as driving the external + /SYNC pin low. diff --git a/Documentation/ABI/testing/sysfs-bus-iio-frequency-adf4350 b/Documentation/ABI/testing/sysfs-bus-iio-frequency-adf4350 new file mode 100644 index 000000000000..d89aded01c5a --- /dev/null +++ b/Documentation/ABI/testing/sysfs-bus-iio-frequency-adf4350 @@ -0,0 +1,21 @@ +What: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY_frequency_resolution +KernelVersion: 3.4.0 +Contact: linux-iio@vger.kernel.org +Description: + Stores channel Y frequency resolution/channel spacing in Hz. + The value given directly influences the MODULUS used by + the fractional-N PLL. It is assumed that the algorithm + that is used to compute the various dividers, is able to + generate proper values for multiples of channel spacing. + +What: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY_refin_frequency +KernelVersion: 3.4.0 +Contact: linux-iio@vger.kernel.org +Description: + Sets channel Y REFin frequency in Hz. In some clock chained + applications, the reference frequency used by the PLL may + change during runtime. This attribute allows the user to + adjust the reference frequency accordingly. + The value written has no effect until out_altvoltageY_frequency + is updated. Consider to use out_altvoltageY_powerdown to power + down the PLL and it's RFOut buffers during REFin changes. diff --git a/Documentation/ABI/testing/sysfs-bus-iio-light-lm3533-als b/Documentation/ABI/testing/sysfs-bus-iio-light-lm3533-als new file mode 100644 index 000000000000..22c5ea670971 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-bus-iio-light-lm3533-als @@ -0,0 +1,61 @@ +What: /sys/.../events/in_illuminance0_thresh_either_en +Date: April 2012 +KernelVersion: 3.5 +Contact: Johan Hovold <jhovold@gmail.com> +Description: + Event generated when channel passes one of the four thresholds + in each direction (rising|falling) and a zone change occurs. + The corresponding light zone can be read from + in_illuminance0_zone. + +What: /sys/.../events/in_illuminance0_threshY_hysteresis +Date: May 2012 +KernelVersion: 3.5 +Contact: Johan Hovold <jhovold@gmail.com> +Description: + Get the hysteresis for thresholds Y, that is, + threshY_hysteresis = threshY_raising - threshY_falling + +What: /sys/.../events/illuminance_threshY_falling_value +What: /sys/.../events/illuminance_threshY_raising_value +Date: April 2012 +KernelVersion: 3.5 +Contact: Johan Hovold <jhovold@gmail.com> +Description: + Specifies the value of threshold that the device is comparing + against for the events enabled by + in_illuminance0_thresh_either_en (0..255), where Y in 0..3. + + Note that threshY_falling must be less than or equal to + threshY_raising. + + These thresholds correspond to the eight zone-boundary + registers (boundaryY_{low,high}) and define the five light + zones. + +What: /sys/bus/iio/devices/iio:deviceX/in_illuminance0_zone +Date: April 2012 +KernelVersion: 3.5 +Contact: Johan Hovold <jhovold@gmail.com> +Description: + Get the current light zone (0..4) as defined by the + in_illuminance0_threshY_{falling,rising} thresholds. + +What: /sys/bus/iio/devices/iio:deviceX/out_currentY_raw +Date: May 2012 +KernelVersion: 3.5 +Contact: Johan Hovold <jhovold@gmail.com> +Description: + Get output current for channel Y (0..255), that is, + out_currentY_currentZ_raw, where Z is the current zone. + +What: /sys/bus/iio/devices/iio:deviceX/out_currentY_currentZ_raw +Date: May 2012 +KernelVersion: 3.5 +Contact: Johan Hovold <jhovold@gmail.com> +Description: + Set the output current for channel out_currentY when in zone + Z (0..255), where Y in 0..2 and Z in 0..4. + + These values correspond to the ALS-mapper target registers for + ALS-mapper Y + 1. diff --git a/Documentation/ramoops.txt b/Documentation/ramoops.txt index 4ba7db231cb2..197ad59ab9bf 100644 --- a/Documentation/ramoops.txt +++ b/Documentation/ramoops.txt @@ -40,6 +40,12 @@ corrupt, but usually it is restorable. Setting the ramoops parameters can be done in 2 different manners: 1. Use the module parameters (which have the names of the variables described as before). + For quick debugging, you can also reserve parts of memory during boot + and then use the reserved memory for ramoops. For example, assuming a machine + with > 128 MB of memory, the following kernel command line will tell the + kernel to use only the first 128 MB of memory, and place ECC-protected ramoops + region at 128 MB boundary: + "mem=128M ramoops.mem_address=0x8000000 ramoops.ecc=1" 2. Use a platform device and set the platform data. The parameters can then be set through that platform data. An example of doing that is: @@ -70,6 +76,14 @@ if (ret) { return ret; } +You can specify either RAM memory or peripheral devices' memory. However, when +specifying RAM, be sure to reserve the memory by issuing memblock_reserve() +very early in the architecture code, e.g.: + +#include <linux/memblock.h> + +memblock_reserve(ramoops_data.mem_address, ramoops_data.mem_size); + 3. Dump format The data dump begins with a header, currently defined as "====" followed by a @@ -80,3 +94,28 @@ timestamp and a new line. The dump then continues with the actual data. The dump data can be read from the pstore filesystem. The format for these files is "dmesg-ramoops-N", where N is the record number in memory. To delete a stored record from RAM, simply unlink the respective pstore file. + +5. Persistent function tracing + +Persistent function tracing might be useful for debugging software or hardware +related hangs. The functions call chain log is stored in a "ftrace-ramoops" +file. Here is an example of usage: + + # mount -t debugfs debugfs /sys/kernel/debug/ + # cd /sys/kernel/debug/tracing + # echo function > current_tracer + # echo 1 > options/func_pstore + # reboot -f + [...] + # mount -t pstore pstore /mnt/ + # tail /mnt/ftrace-ramoops + 0 ffffffff8101ea64 ffffffff8101bcda native_apic_mem_read <- disconnect_bsp_APIC+0x6a/0xc0 + 0 ffffffff8101ea44 ffffffff8101bcf6 native_apic_mem_write <- disconnect_bsp_APIC+0x86/0xc0 + 0 ffffffff81020084 ffffffff8101a4b5 hpet_disable <- native_machine_shutdown+0x75/0x90 + 0 ffffffff81005f94 ffffffff8101a4bb iommu_shutdown_noop <- native_machine_shutdown+0x7b/0x90 + 0 ffffffff8101a6a1 ffffffff8101a437 native_machine_emergency_restart <- native_machine_restart+0x37/0x40 + 0 ffffffff811f9876 ffffffff8101a73a acpi_reboot <- native_machine_emergency_restart+0xaa/0x1e0 + 0 ffffffff8101a514 ffffffff8101a772 mach_reboot_fixups <- native_machine_emergency_restart+0xe2/0x1e0 + 0 ffffffff811d9c54 ffffffff8101a7a0 __const_udelay <- native_machine_emergency_restart+0x110/0x1e0 + 0 ffffffff811d9c34 ffffffff811d9c80 __delay <- __const_udelay+0x30/0x40 + 0 ffffffff811d9d14 ffffffff811d9c3f delay_tsc <- __delay+0xf/0x20 |