diff options
Diffstat (limited to 'arch/arm/boot')
47 files changed, 413 insertions, 68 deletions
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 86217db2937a..992736b5229b 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -223,7 +223,7 @@ dtb-$(CONFIG_SOC_IMX25) += \ imx25-eukrea-mbimxsd25-baseboard-dvi-vga.dtb \ imx25-karo-tx25.dtb \ imx25-pdk.dtb -dtb-$(CONFIG_SOC_IMX31) += \ +dtb-$(CONFIG_SOC_IMX27) += \ imx27-apf27.dtb \ imx27-apf27dev.dtb \ imx27-eukrea-mbimxsd27-baseboard.dtb \ diff --git a/arch/arm/boot/dts/am335x-bone-common.dtsi b/arch/arm/boot/dts/am335x-bone-common.dtsi index c3255e0c90aa..dbb3f4d2bf84 100644 --- a/arch/arm/boot/dts/am335x-bone-common.dtsi +++ b/arch/arm/boot/dts/am335x-bone-common.dtsi @@ -223,6 +223,25 @@ /include/ "tps65217.dtsi" &tps { + /* + * Configure pmic to enter OFF-state instead of SLEEP-state ("RTC-only + * mode") at poweroff. Most BeagleBone versions do not support RTC-only + * mode and risk hardware damage if this mode is entered. + * + * For details, see linux-omap mailing list May 2015 thread + * [PATCH] ARM: dts: am335x-bone* enable pmic-shutdown-controller + * In particular, messages: + * http://www.spinics.net/lists/linux-omap/msg118585.html + * http://www.spinics.net/lists/linux-omap/msg118615.html + * + * You can override this later with + * &tps { /delete-property/ ti,pmic-shutdown-controller; } + * if you want to use RTC-only mode and made sure you are not affected + * by the hardware problems. (Tip: double-check by performing a current + * measurement after shutdown: it should be less than 1 mA.) + */ + ti,pmic-shutdown-controller; + regulators { dcdc1_reg: regulator@0 { regulator-name = "vdds_dpr"; diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts index 5c42d259fa68..901739fcb85a 100644 --- a/arch/arm/boot/dts/am335x-boneblack.dts +++ b/arch/arm/boot/dts/am335x-boneblack.dts @@ -80,7 +80,3 @@ status = "okay"; }; }; - -&rtc { - system-power-controller; -}; diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts index 87fc7a35e802..156d05efcb70 100644 --- a/arch/arm/boot/dts/am335x-evmsk.dts +++ b/arch/arm/boot/dts/am335x-evmsk.dts @@ -654,7 +654,7 @@ wlcore: wlcore@2 { compatible = "ti,wl1271"; reg = <2>; - interrupt-parent = <&gpio1>; + interrupt-parent = <&gpio0>; interrupts = <31 IRQ_TYPE_LEVEL_HIGH>; /* gpio 31 */ ref-clock-frequency = <38400000>; }; diff --git a/arch/arm/boot/dts/am35xx-clocks.dtsi b/arch/arm/boot/dts/am35xx-clocks.dtsi index 518b8fde88b0..18cc826e9db5 100644 --- a/arch/arm/boot/dts/am35xx-clocks.dtsi +++ b/arch/arm/boot/dts/am35xx-clocks.dtsi @@ -12,7 +12,7 @@ #clock-cells = <0>; compatible = "ti,am35xx-gate-clock"; clocks = <&ipss_ick>; - reg = <0x059c>; + reg = <0x032c>; ti,bit-shift = <1>; }; @@ -20,7 +20,7 @@ #clock-cells = <0>; compatible = "ti,gate-clock"; clocks = <&rmii_ck>; - reg = <0x059c>; + reg = <0x032c>; ti,bit-shift = <9>; }; @@ -28,7 +28,7 @@ #clock-cells = <0>; compatible = "ti,am35xx-gate-clock"; clocks = <&ipss_ick>; - reg = <0x059c>; + reg = <0x032c>; ti,bit-shift = <2>; }; @@ -36,7 +36,7 @@ #clock-cells = <0>; compatible = "ti,gate-clock"; clocks = <&pclk_ck>; - reg = <0x059c>; + reg = <0x032c>; ti,bit-shift = <10>; }; @@ -44,7 +44,7 @@ #clock-cells = <0>; compatible = "ti,am35xx-gate-clock"; clocks = <&ipss_ick>; - reg = <0x059c>; + reg = <0x032c>; ti,bit-shift = <0>; }; @@ -52,7 +52,7 @@ #clock-cells = <0>; compatible = "ti,gate-clock"; clocks = <&sys_ck>; - reg = <0x059c>; + reg = <0x032c>; ti,bit-shift = <8>; }; @@ -60,7 +60,7 @@ #clock-cells = <0>; compatible = "ti,am35xx-gate-clock"; clocks = <&sys_ck>; - reg = <0x059c>; + reg = <0x032c>; ti,bit-shift = <3>; }; }; diff --git a/arch/arm/boot/dts/am437x-sk-evm.dts b/arch/arm/boot/dts/am437x-sk-evm.dts index 8ae29c955c11..c17097d2c167 100644 --- a/arch/arm/boot/dts/am437x-sk-evm.dts +++ b/arch/arm/boot/dts/am437x-sk-evm.dts @@ -49,7 +49,7 @@ pinctrl-0 = <&matrix_keypad_pins>; debounce-delay-ms = <5>; - col-scan-delay-us = <1500>; + col-scan-delay-us = <5>; row-gpios = <&gpio5 5 GPIO_ACTIVE_HIGH /* Bank5, pin5 */ &gpio5 6 GPIO_ACTIVE_HIGH>; /* Bank5, pin6 */ @@ -473,7 +473,7 @@ interrupt-parent = <&gpio0>; interrupts = <31 0>; - wake-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio1 28 GPIO_ACTIVE_LOW>; touchscreen-size-x = <480>; touchscreen-size-y = <272>; diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts index 15f198e4864d..a42cc377a862 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15.dts +++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts @@ -18,6 +18,8 @@ aliases { rtc0 = &mcp_rtc; rtc1 = &tps659038_rtc; + rtc2 = &rtc; + display0 = &hdmi0; }; memory { @@ -83,7 +85,7 @@ gpio_fan: gpio_fan { /* Based on 5v 500mA AFB02505HHB */ compatible = "gpio-fan"; - gpios = <&tps659038_gpio 1 GPIO_ACTIVE_HIGH>; + gpios = <&tps659038_gpio 2 GPIO_ACTIVE_HIGH>; gpio-fan,speed-map = <0 0>, <13000 1>; #cooling-cells = <2>; @@ -102,6 +104,51 @@ pinctrl-names = "default"; pinctrl-0 = <&extcon_usb2_pins>; }; + + hdmi0: connector { + compatible = "hdmi-connector"; + label = "hdmi"; + + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&tpd12s015_out>; + }; + }; + }; + + tpd12s015: encoder { + compatible = "ti,tpd12s015"; + + pinctrl-names = "default"; + pinctrl-0 = <&tpd12s015_pins>; + + gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>, /* gpio7_10, CT CP HPD */ + <&gpio6 28 GPIO_ACTIVE_HIGH>, /* gpio6_28, LS OE */ + <&gpio7 12 GPIO_ACTIVE_HIGH>; /* gpio7_12/sp1_cs2, HPD */ + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + tpd12s015_in: endpoint { + remote-endpoint = <&hdmi_out>; + }; + }; + + port@1 { + reg = <1>; + + tpd12s015_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; + }; + }; + }; }; &dra7_pmx_core { @@ -121,6 +168,13 @@ >; }; + hdmi_pins: pinmux_hdmi_pins { + pinctrl-single,pins = < + 0x408 (PIN_INPUT | MUX_MODE1) /* i2c2_sda.hdmi1_ddc_scl */ + 0x40c (PIN_INPUT | MUX_MODE1) /* i2c2_scl.hdmi1_ddc_sda */ + >; + }; + i2c3_pins_default: i2c3_pins_default { pinctrl-single,pins = < 0x2a4 (PIN_INPUT| MUX_MODE10) /* mcasp1_aclkx.i2c3_sda */ @@ -130,8 +184,8 @@ uart3_pins_default: uart3_pins_default { pinctrl-single,pins = < - 0x248 (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_rxd.rxd */ - 0x24c (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd.txd */ + 0x3f8 (PIN_INPUT_SLEW | MUX_MODE2) /* uart2_ctsn.uart3_rxd */ + 0x3fc (PIN_INPUT_SLEW | MUX_MODE1) /* uart2_rtsn.uart3_txd */ >; }; @@ -277,6 +331,14 @@ 0x3e8 (PIN_INPUT_PULLUP | MUX_MODE14) /* uart1_ctsn.gpio7_24 */ >; }; + + tpd12s015_pins: pinmux_tpd12s015_pins { + pinctrl-single,pins = < + 0x3b0 (PIN_OUTPUT | MUX_MODE14) /* gpio7_10 CT_CP_HPD */ + 0x3b8 (PIN_INPUT_PULLDOWN | MUX_MODE14) /* gpio7_12 HPD */ + 0x370 (PIN_OUTPUT | MUX_MODE14) /* gpio6_28 LS_OE */ + >; + }; }; &i2c1 { @@ -455,7 +517,7 @@ mcp_rtc: rtc@6f { compatible = "microchip,mcp7941x"; reg = <0x6f>; - interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_LOW>; /* IRQ_SYS_1N */ + interrupts = <GIC_SPI 2 IRQ_TYPE_EDGE_RISING>; /* IRQ_SYS_1N */ pinctrl-names = "default"; pinctrl-0 = <&mcp79410_pins_default>; @@ -478,7 +540,7 @@ &uart3 { status = "okay"; interrupts-extended = <&crossbar_mpu GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>, - <&dra7_pmx_core 0x248>; + <&dra7_pmx_core 0x3f8>; pinctrl-names = "default"; pinctrl-0 = <&uart3_pins_default>; @@ -607,3 +669,23 @@ }; }; }; + +&dss { + status = "ok"; + + vdda_video-supply = <&ldoln_reg>; +}; + +&hdmi { + status = "ok"; + vdda-supply = <&ldo3_reg>; + + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_pins>; + + port { + hdmi_out: endpoint { + remote-endpoint = <&tpd12s015_in>; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-375.dtsi b/arch/arm/boot/dts/armada-375.dtsi index c675257f2377..f076ff856d8b 100644 --- a/arch/arm/boot/dts/armada-375.dtsi +++ b/arch/arm/boot/dts/armada-375.dtsi @@ -69,7 +69,7 @@ mainpll: mainpll { compatible = "fixed-clock"; #clock-cells = <0>; - clock-frequency = <2000000000>; + clock-frequency = <1000000000>; }; /* 25 MHz reference crystal */ refclk: oscillator { diff --git a/arch/arm/boot/dts/armada-38x.dtsi b/arch/arm/boot/dts/armada-38x.dtsi index ed2dd8ba4080..218a2acd36e5 100644 --- a/arch/arm/boot/dts/armada-38x.dtsi +++ b/arch/arm/boot/dts/armada-38x.dtsi @@ -585,7 +585,7 @@ mainpll: mainpll { compatible = "fixed-clock"; #clock-cells = <0>; - clock-frequency = <2000000000>; + clock-frequency = <1000000000>; }; /* 25 MHz reference crystal */ diff --git a/arch/arm/boot/dts/armada-39x.dtsi b/arch/arm/boot/dts/armada-39x.dtsi index 0e85fc15ceda..ecd1318109ba 100644 --- a/arch/arm/boot/dts/armada-39x.dtsi +++ b/arch/arm/boot/dts/armada-39x.dtsi @@ -502,7 +502,7 @@ mainpll: mainpll { compatible = "fixed-clock"; #clock-cells = <0>; - clock-frequency = <2000000000>; + clock-frequency = <1000000000>; }; }; }; diff --git a/arch/arm/boot/dts/armada-xp-linksys-mamba.dts b/arch/arm/boot/dts/armada-xp-linksys-mamba.dts index a2cf2154dcdb..fdd187c55aa5 100644 --- a/arch/arm/boot/dts/armada-xp-linksys-mamba.dts +++ b/arch/arm/boot/dts/armada-xp-linksys-mamba.dts @@ -95,6 +95,11 @@ internal-regs { + rtc@10300 { + /* No crystal connected to the internal RTC */ + status = "disabled"; + }; + /* J10: VCC, NC, RX, NC, TX, GND */ serial@12000 { status = "okay"; diff --git a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts index e3b08fb959e5..990e8a2100f0 100644 --- a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts +++ b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts @@ -105,6 +105,10 @@ }; internal-regs { + rtc@10300 { + /* No crystal connected to the internal RTC */ + status = "disabled"; + }; serial@12000 { status = "okay"; }; diff --git a/arch/arm/boot/dts/dm816x.dtsi b/arch/arm/boot/dts/dm816x.dtsi index de8427be830a..289806adb343 100644 --- a/arch/arm/boot/dts/dm816x.dtsi +++ b/arch/arm/boot/dts/dm816x.dtsi @@ -382,7 +382,7 @@ ti,hwmods = "usb_otg_hs"; usb0: usb@47401000 { - compatible = "ti,musb-am33xx"; + compatible = "ti,musb-dm816"; reg = <0x47401400 0x400 0x47401000 0x200>; reg-names = "mc", "control"; @@ -422,7 +422,7 @@ }; usb1: usb@47401800 { - compatible = "ti,musb-am33xx"; + compatible = "ti,musb-dm816"; reg = <0x47401c00 0x400 0x47401800 0x200>; reg-names = "mc", "control"; diff --git a/arch/arm/boot/dts/dove-cubox.dts b/arch/arm/boot/dts/dove-cubox.dts index aae7efc09b0b..e6fa251e17b9 100644 --- a/arch/arm/boot/dts/dove-cubox.dts +++ b/arch/arm/boot/dts/dove-cubox.dts @@ -87,6 +87,7 @@ /* connect xtal input to 25MHz reference */ clocks = <&ref25>; + clock-names = "xtal"; /* connect xtal input as source of pll0 and pll1 */ silabs,pll-source = <0 0>, <1 0>; diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi index 5332b57b4950..8f1e25bcecbd 100644 --- a/arch/arm/boot/dts/dra7.dtsi +++ b/arch/arm/boot/dts/dra7.dtsi @@ -131,6 +131,11 @@ regulator-max-microvolt = <3000000>; }; }; + + scm_conf_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; }; dra7_pmx_core: pinmux@1400 { @@ -911,7 +916,7 @@ ti,clock-cycles = <16>; reg = <0x4ae07ddc 0x4>, <0x4ae07de0 0x4>, - <0x4ae06014 0x4>, <0x4a003b20 0x8>, + <0x4ae06014 0x4>, <0x4a003b20 0xc>, <0x4ae0c158 0x4>; reg-names = "setup-address", "control-address", "int-address", "efuse-address", @@ -944,7 +949,7 @@ ti,clock-cycles = <16>; reg = <0x4ae07e34 0x4>, <0x4ae07e24 0x4>, - <0x4ae06010 0x4>, <0x4a0025cc 0x8>, + <0x4ae06010 0x4>, <0x4a0025cc 0xc>, <0x4a002470 0x4>; reg-names = "setup-address", "control-address", "int-address", "efuse-address", @@ -977,7 +982,7 @@ ti,clock-cycles = <16>; reg = <0x4ae07e30 0x4>, <0x4ae07e20 0x4>, - <0x4ae06010 0x4>, <0x4a0025e0 0x8>, + <0x4ae06010 0x4>, <0x4a0025e0 0xc>, <0x4a00246c 0x4>; reg-names = "setup-address", "control-address", "int-address", "efuse-address", @@ -1010,7 +1015,7 @@ ti,clock-cycles = <16>; reg = <0x4ae07de4 0x4>, <0x4ae07de8 0x4>, - <0x4ae06010 0x4>, <0x4a003b08 0x8>, + <0x4ae06010 0x4>, <0x4a003b08 0xc>, <0x4ae0c154 0x4>; reg-names = "setup-address", "control-address", "int-address", "efuse-address", @@ -1203,7 +1208,7 @@ status = "disabled"; }; - rtc@48838000 { + rtc: rtc@48838000 { compatible = "ti,am3352-rtc"; reg = <0x48838000 0x100>; interrupts = <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>, @@ -1469,6 +1474,44 @@ clocks = <&sys_clkin1>; status = "disabled"; }; + + dss: dss@58000000 { + compatible = "ti,dra7-dss"; + /* 'reg' defined in dra72x.dtsi and dra74x.dtsi */ + /* 'clocks' defined in dra72x.dtsi and dra74x.dtsi */ + status = "disabled"; + ti,hwmods = "dss_core"; + /* CTRL_CORE_DSS_PLL_CONTROL */ + syscon-pll-ctrl = <&scm_conf 0x538>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + dispc@58001000 { + compatible = "ti,dra7-dispc"; + reg = <0x58001000 0x1000>; + interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "dss_dispc"; + clocks = <&dss_dss_clk>; + clock-names = "fck"; + /* CTRL_CORE_SMA_SW_1 */ + syscon-pol = <&scm_conf 0x534>; + }; + + hdmi: encoder@58060000 { + compatible = "ti,dra7-hdmi"; + reg = <0x58040000 0x200>, + <0x58040200 0x80>, + <0x58040300 0x80>, + <0x58060000 0x19000>; + reg-names = "wp", "pll", "phy", "core"; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + ti,hwmods = "dss_hdmi"; + clocks = <&dss_48mhz_clk>, <&dss_hdmi_clk>; + clock-names = "fck", "sys_clk"; + }; + }; }; thermal_zones: thermal-zones { diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm.dts index ce0390f081d9..4e1b60581782 100644 --- a/arch/arm/boot/dts/dra72-evm.dts +++ b/arch/arm/boot/dts/dra72-evm.dts @@ -19,6 +19,10 @@ reg = <0x80000000 0x40000000>; /* 1024 MB */ }; + aliases { + display0 = &hdmi0; + }; + evm_3v3: fixedregulator-evm_3v3 { compatible = "regulator-fixed"; regulator-name = "evm_3v3"; @@ -35,6 +39,51 @@ compatible = "linux,extcon-usb-gpio"; id-gpio = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>; }; + + hdmi0: connector { + compatible = "hdmi-connector"; + label = "hdmi"; + + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&tpd12s015_out>; + }; + }; + }; + + tpd12s015: encoder { + compatible = "ti,tpd12s015"; + + pinctrl-names = "default"; + pinctrl-0 = <&tpd12s015_pins>; + + gpios = <&pcf_hdmi 4 GPIO_ACTIVE_HIGH>, /* P4, CT CP HPD */ + <&pcf_hdmi 5 GPIO_ACTIVE_HIGH>, /* P5, LS OE */ + <&gpio7 12 GPIO_ACTIVE_HIGH>; /* gpio7_12/sp1_cs2, HPD */ + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + tpd12s015_in: endpoint { + remote-endpoint = <&hdmi_out>; + }; + }; + + port@1 { + reg = <1>; + + tpd12s015_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; + }; + }; + }; }; &dra7_pmx_core { @@ -45,6 +94,13 @@ >; }; + i2c5_pins: pinmux_i2c5_pins { + pinctrl-single,pins = < + 0x2b4 (PIN_INPUT | MUX_MODE10) /* mcasp1_axr0.i2c5_sda */ + 0x2b8 (PIN_INPUT | MUX_MODE10) /* mcasp1_axr1.i2c5_scl */ + >; + }; + nand_default: nand_default { pinctrl-single,pins = < 0x0 (PIN_INPUT | MUX_MODE0) /* gpmc_ad0 */ @@ -142,6 +198,19 @@ 0xb8 (PIN_OUTPUT | MUX_MODE1) /* gpmc_cs2.qspi1_cs0 */ >; }; + + hdmi_pins: pinmux_hdmi_pins { + pinctrl-single,pins = < + 0x408 (PIN_INPUT | MUX_MODE1) /* i2c2_sda.hdmi1_ddc_scl */ + 0x40c (PIN_INPUT | MUX_MODE1) /* i2c2_scl.hdmi1_ddc_sda */ + >; + }; + + tpd12s015_pins: pinmux_tpd12s015_pins { + pinctrl-single,pins = < + 0x3b8 (PIN_INPUT_PULLDOWN | MUX_MODE14) /* gpio7_12 HPD */ + >; + }; }; &i2c1 { @@ -277,6 +346,27 @@ }; }; +&i2c5 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c5_pins>; + clock-frequency = <400000>; + + pcf_hdmi: pcf8575@26 { + compatible = "nxp,pcf8575"; + reg = <0x26>; + gpio-controller; + #gpio-cells = <2>; + /* + * initial state is used here to keep the mdio interface + * selected on RU89 through SEL_VIN4_MUX_S0, VIN2_S1 and + * VIN2_S0 driven high otherwise Ethernet stops working + * VIN6_SEL_S0 is low, thus selecting McASP3 over VIN6 + */ + lines-initial-states = <0x0f2b>; + }; +}; + &uart1 { status = "okay"; }; @@ -566,3 +656,23 @@ }; }; }; + +&dss { + status = "ok"; + + vdda_video-supply = <&ldo5_reg>; +}; + +&hdmi { + status = "ok"; + vdda-supply = <&ldo3_reg>; + + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_pins>; + + port { + hdmi_out: endpoint { + remote-endpoint = <&tpd12s015_in>; + }; + }; +}; diff --git a/arch/arm/boot/dts/dra72x.dtsi b/arch/arm/boot/dts/dra72x.dtsi index 03d742f8d572..eaca143faa77 100644 --- a/arch/arm/boot/dts/dra72x.dtsi +++ b/arch/arm/boot/dts/dra72x.dtsi @@ -34,3 +34,14 @@ interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; }; }; + +&dss { + reg = <0x58000000 0x80>, + <0x58004054 0x4>, + <0x58004300 0x20>; + reg-names = "dss", "pll1_clkctrl", "pll1"; + + clocks = <&dss_dss_clk>, + <&dss_video1_clk>; + clock-names = "fck", "video1_clk"; +}; diff --git a/arch/arm/boot/dts/dra74x.dtsi b/arch/arm/boot/dts/dra74x.dtsi index cc560a70926f..fa995d0ca1f2 100644 --- a/arch/arm/boot/dts/dra74x.dtsi +++ b/arch/arm/boot/dts/dra74x.dtsi @@ -73,3 +73,18 @@ }; }; }; + +&dss { + reg = <0x58000000 0x80>, + <0x58004054 0x4>, + <0x58004300 0x20>, + <0x58005054 0x4>, + <0x58005300 0x20>; + reg-names = "dss", "pll1_clkctrl", "pll1", + "pll2_clkctrl", "pll2"; + + clocks = <&dss_dss_clk>, + <&dss_video1_clk>, + <&dss_video2_clk>; + clock-names = "fck", "video1_clk", "video2_clk"; +}; diff --git a/arch/arm/boot/dts/dra7xx-clocks.dtsi b/arch/arm/boot/dts/dra7xx-clocks.dtsi index 3b933f74d000..357bedeebfac 100644 --- a/arch/arm/boot/dts/dra7xx-clocks.dtsi +++ b/arch/arm/boot/dts/dra7xx-clocks.dtsi @@ -1531,6 +1531,7 @@ clocks = <&dpll_per_h12x2_ck>; ti,bit-shift = <8>; reg = <0x1120>; + ti,set-rate-parent; }; dss_hdmi_clk: dss_hdmi_clk { @@ -2136,3 +2137,13 @@ clocks = <&dpll_usb_ck>; }; }; + +&scm_conf_clocks { + dss_deshdcp_clk: dss_deshdcp_clk { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&l3_iclk_div>; + ti,bit-shift = <0>; + reg = <0x558>; + }; +}; diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi index 8de12af7c276..d6b49e5b32e9 100644 --- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi +++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi @@ -9,6 +9,7 @@ #include <dt-bindings/sound/samsung-i2s.h> #include <dt-bindings/input/input.h> +#include <dt-bindings/clock/maxim,max77686.h> #include "exynos4412.dtsi" / { @@ -105,6 +106,8 @@ rtc@10070000 { status = "okay"; + clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>; + clock-names = "rtc", "rtc_src"; }; g2d@10800000 { diff --git a/arch/arm/boot/dts/exynos4412-trats2.dts b/arch/arm/boot/dts/exynos4412-trats2.dts index 173ffa479ad3..792394dd0f2a 100644 --- a/arch/arm/boot/dts/exynos4412-trats2.dts +++ b/arch/arm/boot/dts/exynos4412-trats2.dts @@ -736,7 +736,7 @@ display-timings { timing-0 { - clock-frequency = <0>; + clock-frequency = <57153600>; hactive = <720>; vactive = <1280>; hfront-porch = <5>; diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts index 2657e842e5a5..1eca97ee4bd6 100644 --- a/arch/arm/boot/dts/exynos5250-snow.dts +++ b/arch/arm/boot/dts/exynos5250-snow.dts @@ -567,6 +567,7 @@ num-slots = <1>; broken-cd; cap-sdio-irq; + keep-power-in-suspend; card-detect-delay = <200>; samsung,dw-mshc-ciu-div = <3>; samsung,dw-mshc-sdr-timing = <2 3>; diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts index 0788d08fb43e..146e71118a72 100644 --- a/arch/arm/boot/dts/exynos5420-peach-pit.dts +++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts @@ -711,6 +711,7 @@ num-slots = <1>; broken-cd; cap-sdio-irq; + keep-power-in-suspend; card-detect-delay = <200>; clock-frequency = <400000000>; samsung,dw-mshc-ciu-div = <1>; diff --git a/arch/arm/boot/dts/exynos5420-trip-points.dtsi b/arch/arm/boot/dts/exynos5420-trip-points.dtsi index 5d31fc140823..2180a0152c9b 100644 --- a/arch/arm/boot/dts/exynos5420-trip-points.dtsi +++ b/arch/arm/boot/dts/exynos5420-trip-points.dtsi @@ -28,7 +28,7 @@ trips { type = "active"; }; cpu-crit-0 { - temperature = <1200000>; /* millicelsius */ + temperature = <120000>; /* millicelsius */ hysteresis = <0>; /* millicelsius */ type = "critical"; }; diff --git a/arch/arm/boot/dts/exynos5420.dtsi b/arch/arm/boot/dts/exynos5420.dtsi index f67b23f303c3..45317538bbae 100644 --- a/arch/arm/boot/dts/exynos5420.dtsi +++ b/arch/arm/boot/dts/exynos5420.dtsi @@ -536,6 +536,7 @@ clock-names = "dp"; phys = <&dp_phy>; phy-names = "dp"; + power-domains = <&disp_pd>; }; mipi_phy: video-phy@10040714 { diff --git a/arch/arm/boot/dts/exynos5440-trip-points.dtsi b/arch/arm/boot/dts/exynos5440-trip-points.dtsi index 48adfa8f4300..356e963edf11 100644 --- a/arch/arm/boot/dts/exynos5440-trip-points.dtsi +++ b/arch/arm/boot/dts/exynos5440-trip-points.dtsi @@ -18,7 +18,7 @@ trips { type = "active"; }; cpu-crit-0 { - temperature = <1050000>; /* millicelsius */ + temperature = <105000>; /* millicelsius */ hysteresis = <0>; /* millicelsius */ type = "critical"; }; diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts index 412f41d62686..02eb8b15374f 100644 --- a/arch/arm/boot/dts/exynos5800-peach-pi.dts +++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts @@ -674,6 +674,7 @@ num-slots = <1>; broken-cd; cap-sdio-irq; + keep-power-in-suspend; card-detect-delay = <200>; clock-frequency = <400000000>; samsung,dw-mshc-ciu-div = <1>; diff --git a/arch/arm/boot/dts/imx23-olinuxino.dts b/arch/arm/boot/dts/imx23-olinuxino.dts index 7e6eef2488e8..82045398bf1f 100644 --- a/arch/arm/boot/dts/imx23-olinuxino.dts +++ b/arch/arm/boot/dts/imx23-olinuxino.dts @@ -12,6 +12,7 @@ */ /dts-v1/; +#include <dt-bindings/gpio/gpio.h> #include "imx23.dtsi" / { @@ -93,6 +94,7 @@ ahb@80080000 { usb0: usb@80080000 { + dr_mode = "host"; vbus-supply = <®_usb0_vbus>; status = "okay"; }; @@ -122,7 +124,7 @@ user { label = "green"; - gpios = <&gpio2 1 1>; + gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>; }; }; }; diff --git a/arch/arm/boot/dts/imx25.dtsi b/arch/arm/boot/dts/imx25.dtsi index e4d3aecc4ed2..677f81d9dcd5 100644 --- a/arch/arm/boot/dts/imx25.dtsi +++ b/arch/arm/boot/dts/imx25.dtsi @@ -428,6 +428,7 @@ pwm4: pwm@53fc8000 { compatible = "fsl,imx25-pwm", "fsl,imx27-pwm"; + #pwm-cells = <2>; reg = <0x53fc8000 0x4000>; clocks = <&clks 108>, <&clks 52>; clock-names = "ipg", "per"; diff --git a/arch/arm/boot/dts/imx27.dtsi b/arch/arm/boot/dts/imx27.dtsi index 6951b66d1ab7..bc215e4b75fd 100644 --- a/arch/arm/boot/dts/imx27.dtsi +++ b/arch/arm/boot/dts/imx27.dtsi @@ -533,7 +533,7 @@ fec: ethernet@1002b000 { compatible = "fsl,imx27-fec"; - reg = <0x1002b000 0x4000>; + reg = <0x1002b000 0x1000>; interrupts = <50>; clocks = <&clks IMX27_CLK_FEC_IPG_GATE>, <&clks IMX27_CLK_FEC_AHB_GATE>; diff --git a/arch/arm/boot/dts/imx28-cfa10036.dts b/arch/arm/boot/dts/imx28-cfa10036.dts index b04b6b8850a7..570aa339a05e 100644 --- a/arch/arm/boot/dts/imx28-cfa10036.dts +++ b/arch/arm/boot/dts/imx28-cfa10036.dts @@ -99,6 +99,9 @@ solomon,height = <32>; solomon,width = <128>; solomon,page-offset = <0>; + solomon,com-lrremap; + solomon,com-invdir; + solomon,com-offset = <32>; }; }; diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi index 25e25f82fbae..4e073e854742 100644 --- a/arch/arm/boot/dts/imx28.dtsi +++ b/arch/arm/boot/dts/imx28.dtsi @@ -913,7 +913,7 @@ 80 81 68 69 70 71 72 73 74 75 76 77>; - interrupt-names = "auart4-rx", "aurat4-tx", "spdif-tx", "empty", + interrupt-names = "auart4-rx", "auart4-tx", "spdif-tx", "empty", "saif0", "saif1", "i2c0", "i2c1", "auart0-rx", "auart0-tx", "auart1-rx", "auart1-tx", "auart2-rx", "auart2-tx", "auart3-rx", "auart3-tx"; diff --git a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi index 19cc269a08d4..1ce6133b67f5 100644 --- a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi +++ b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi @@ -31,6 +31,7 @@ regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; gpio = <&gpio4 15 0>; + enable-active-high; }; reg_usb_h1_vbus: regulator@1 { @@ -40,6 +41,7 @@ regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; gpio = <&gpio1 0 0>; + enable-active-high; }; }; diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi index 46b2fed7c319..3b24b12651b2 100644 --- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi +++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi @@ -185,7 +185,6 @@ &i2c3 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_i2c3>; - pinctrl-assert-gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>; status = "okay"; max7310_a: gpio@30 { diff --git a/arch/arm/boot/dts/omap3-devkit8000.dts b/arch/arm/boot/dts/omap3-devkit8000.dts index 134d3f27a8ec..921de6605f07 100644 --- a/arch/arm/boot/dts/omap3-devkit8000.dts +++ b/arch/arm/boot/dts/omap3-devkit8000.dts @@ -110,6 +110,8 @@ nand@0,0 { reg = <0 0 4>; /* CS0, offset 0, IO size 4 */ nand-bus-width = <16>; + gpmc,device-width = <2>; + ti,nand-ecc-opt = "sw"; gpmc,sync-clk-ps = <0>; gpmc,cs-on-ns = <0>; diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts index a29315833ecd..5f5e0f3d5b64 100644 --- a/arch/arm/boot/dts/omap3-n900.dts +++ b/arch/arm/boot/dts/omap3-n900.dts @@ -498,6 +498,8 @@ DRVDD-supply = <&vmmc2>; IOVDD-supply = <&vio>; DVDD-supply = <&vio>; + + ai3x-micbias-vg = <1>; }; tlv320aic3x_aux: tlv320aic3x@19 { @@ -509,6 +511,8 @@ DRVDD-supply = <&vmmc2>; IOVDD-supply = <&vio>; DVDD-supply = <&vio>; + + ai3x-micbias-vg = <2>; }; tsl2563: tsl2563@29 { @@ -828,8 +832,8 @@ touchscreen-fuzz-x = <4>; touchscreen-fuzz-y = <7>; touchscreen-fuzz-pressure = <2>; - touchscreen-max-x = <4096>; - touchscreen-max-y = <4096>; + touchscreen-size-x = <4096>; + touchscreen-size-y = <4096>; touchscreen-max-pressure = <2048>; ti,x-plate-ohms = <280>; diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi index d18a90f5eca3..69a40cfc1f29 100644 --- a/arch/arm/boot/dts/omap3.dtsi +++ b/arch/arm/boot/dts/omap3.dtsi @@ -456,6 +456,7 @@ }; mmu_isp: mmu@480bd400 { + #iommu-cells = <0>; compatible = "ti,omap2-iommu"; reg = <0x480bd400 0x80>; interrupts = <24>; @@ -464,6 +465,7 @@ }; mmu_iva: mmu@5d000000 { + #iommu-cells = <0>; compatible = "ti,omap2-iommu"; reg = <0x5d000000 0x80>; interrupts = <28>; diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi index efe5f737f39b..7d24ae0306b5 100644 --- a/arch/arm/boot/dts/omap5.dtsi +++ b/arch/arm/boot/dts/omap5.dtsi @@ -128,7 +128,7 @@ * hierarchy. */ ocp { - compatible = "ti,omap4-l3-noc", "simple-bus"; + compatible = "ti,omap5-l3-noc", "simple-bus"; #address-cells = <1>; #size-cells = <1>; ranges; diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts index 74c3212f1f11..824ddab9c3ad 100644 --- a/arch/arm/boot/dts/r8a7791-koelsch.dts +++ b/arch/arm/boot/dts/r8a7791-koelsch.dts @@ -545,7 +545,7 @@ compatible = "adi,adv7511w"; reg = <0x39>; interrupt-parent = <&gpio3>; - interrupts = <29 IRQ_TYPE_EDGE_FALLING>; + interrupts = <29 IRQ_TYPE_LEVEL_LOW>; adi,input-depth = <8>; adi,input-colorspace = "rgb"; diff --git a/arch/arm/boot/dts/socfpga_arria10.dtsi b/arch/arm/boot/dts/socfpga_arria10.dtsi index 8a05c47fd57f..4be75960a603 100644 --- a/arch/arm/boot/dts/socfpga_arria10.dtsi +++ b/arch/arm/boot/dts/socfpga_arria10.dtsi @@ -253,6 +253,17 @@ status = "disabled"; }; + sdr: sdr@ffc25000 { + compatible = "syscon"; + reg = <0xffcfb100 0x80>; + }; + + sdramedac { + compatible = "altr,sdram-edac-a10"; + altr,sdr-syscon = <&sdr>; + interrupts = <0 2 4>, <0 0 4>; + }; + L2: l2-cache@fffff000 { compatible = "arm,pl310-cache"; reg = <0xfffff000 0x1000>; diff --git a/arch/arm/boot/dts/ste-dbx5x0.dtsi b/arch/arm/boot/dts/ste-dbx5x0.dtsi index bfd3f1c734b8..2201cd5da3bb 100644 --- a/arch/arm/boot/dts/ste-dbx5x0.dtsi +++ b/arch/arm/boot/dts/ste-dbx5x0.dtsi @@ -1017,23 +1017,6 @@ status = "disabled"; }; - vmmci: regulator-gpio { - compatible = "regulator-gpio"; - - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <2900000>; - regulator-name = "mmci-reg"; - regulator-type = "voltage"; - - startup-delay-us = <100>; - enable-active-high; - - states = <1800000 0x1 - 2900000 0x0>; - - status = "disabled"; - }; - mcde@a0350000 { compatible = "stericsson,mcde"; reg = <0xa0350000 0x1000>, /* MCDE */ diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi index bf8f0eddc2c0..744c1e3a744d 100644 --- a/arch/arm/boot/dts/ste-href.dtsi +++ b/arch/arm/boot/dts/ste-href.dtsi @@ -111,6 +111,21 @@ pinctrl-1 = <&i2c3_sleep_mode>; }; + vmmci: regulator-gpio { + compatible = "regulator-gpio"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2900000>; + regulator-name = "mmci-reg"; + regulator-type = "voltage"; + + startup-delay-us = <100>; + enable-active-high; + + states = <1800000 0x1 + 2900000 0x0>; + }; + // External Micro SD slot sdi0_per1@80126000 { arm,primecell-periphid = <0x10480180>; diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts index 206826a855c0..1bc84ebdccaa 100644 --- a/arch/arm/boot/dts/ste-snowball.dts +++ b/arch/arm/boot/dts/ste-snowball.dts @@ -146,8 +146,21 @@ }; vmmci: regulator-gpio { + compatible = "regulator-gpio"; + gpios = <&gpio7 4 0x4>; enable-gpio = <&gpio6 25 0x4>; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2900000>; + regulator-name = "mmci-reg"; + regulator-type = "voltage"; + + startup-delay-us = <100>; + enable-active-high; + + states = <1800000 0x1 + 2900000 0x0>; }; // External Micro SD slot diff --git a/arch/arm/boot/dts/tegra124.dtsi b/arch/arm/boot/dts/tegra124.dtsi index cf01c818b8ea..13cc7ca5e031 100644 --- a/arch/arm/boot/dts/tegra124.dtsi +++ b/arch/arm/boot/dts/tegra124.dtsi @@ -826,7 +826,7 @@ <&tegra_car TEGRA124_CLK_PLL_U>, <&tegra_car TEGRA124_CLK_USBD>; clock-names = "reg", "pll_u", "utmi-pads"; - resets = <&tegra_car 59>, <&tegra_car 22>; + resets = <&tegra_car 22>, <&tegra_car 22>; reset-names = "usb", "utmi-pads"; nvidia,hssync-start-delay = <0>; nvidia,idle-wait-delay = <17>; @@ -838,6 +838,7 @@ nvidia,hssquelch-level = <2>; nvidia,hsdiscon-level = <5>; nvidia,xcvr-hsslew = <12>; + nvidia,has-utmi-pad-registers; status = "disabled"; }; @@ -862,7 +863,7 @@ <&tegra_car TEGRA124_CLK_PLL_U>, <&tegra_car TEGRA124_CLK_USBD>; clock-names = "reg", "pll_u", "utmi-pads"; - resets = <&tegra_car 22>, <&tegra_car 22>; + resets = <&tegra_car 58>, <&tegra_car 22>; reset-names = "usb", "utmi-pads"; nvidia,hssync-start-delay = <0>; nvidia,idle-wait-delay = <17>; @@ -874,7 +875,6 @@ nvidia,hssquelch-level = <2>; nvidia,hsdiscon-level = <5>; nvidia,xcvr-hsslew = <12>; - nvidia,has-utmi-pad-registers; status = "disabled"; }; @@ -899,7 +899,7 @@ <&tegra_car TEGRA124_CLK_PLL_U>, <&tegra_car TEGRA124_CLK_USBD>; clock-names = "reg", "pll_u", "utmi-pads"; - resets = <&tegra_car 58>, <&tegra_car 22>; + resets = <&tegra_car 59>, <&tegra_car 22>; reset-names = "usb", "utmi-pads"; nvidia,hssync-start-delay = <0>; nvidia,idle-wait-delay = <17>; diff --git a/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts b/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts index 7a2aeacd62c0..107395c32d82 100644 --- a/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts +++ b/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts @@ -191,6 +191,7 @@ compatible = "arm,cortex-a15-pmu"; interrupts = <0 68 4>, <0 69 4>; + interrupt-affinity = <&cpu0>, <&cpu1>; }; oscclk6a: oscclk6a { diff --git a/arch/arm/boot/dts/vexpress-v2p-ca9.dts b/arch/arm/boot/dts/vexpress-v2p-ca9.dts index 23662b5a5e9d..d949facba376 100644 --- a/arch/arm/boot/dts/vexpress-v2p-ca9.dts +++ b/arch/arm/boot/dts/vexpress-v2p-ca9.dts @@ -33,28 +33,28 @@ #address-cells = <1>; #size-cells = <0>; - cpu@0 { + A9_0: cpu@0 { device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <0>; next-level-cache = <&L2>; }; - cpu@1 { + A9_1: cpu@1 { device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <1>; next-level-cache = <&L2>; }; - cpu@2 { + A9_2: cpu@2 { device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <2>; next-level-cache = <&L2>; }; - cpu@3 { + A9_3: cpu@3 { device_type = "cpu"; compatible = "arm,cortex-a9"; reg = <3>; @@ -170,6 +170,7 @@ compatible = "arm,pl310-cache"; reg = <0x1e00a000 0x1000>; interrupts = <0 43 4>; + cache-unified; cache-level = <2>; arm,data-latency = <1 1 1>; arm,tag-latency = <1 1 1>; @@ -181,6 +182,8 @@ <0 61 4>, <0 62 4>, <0 63 4>; + interrupt-affinity = <&A9_0>, <&A9_1>, <&A9_2>, <&A9_3>; + }; dcc { diff --git a/arch/arm/boot/dts/zynq-7000.dtsi b/arch/arm/boot/dts/zynq-7000.dtsi index a5cd2eda3edf..9ea54b3dba09 100644 --- a/arch/arm/boot/dts/zynq-7000.dtsi +++ b/arch/arm/boot/dts/zynq-7000.dtsi @@ -193,7 +193,7 @@ }; gem0: ethernet@e000b000 { - compatible = "cdns,gem"; + compatible = "cdns,zynq-gem"; reg = <0xe000b000 0x1000>; status = "disabled"; interrupts = <0 22 4>; @@ -204,7 +204,7 @@ }; gem1: ethernet@e000c000 { - compatible = "cdns,gem"; + compatible = "cdns,zynq-gem"; reg = <0xe000c000 0x1000>; status = "disabled"; interrupts = <0 45 4>; |