diff options
Diffstat (limited to 'arch/arm/mach-at91/board-sam9g20ek.c')
| -rw-r--r-- | arch/arm/mach-at91/board-sam9g20ek.c | 182 |
1 files changed, 171 insertions, 11 deletions
diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c index cc270beadd5d..ca8198b3c168 100644 --- a/arch/arm/mach-at91/board-sam9g20ek.c +++ b/arch/arm/mach-at91/board-sam9g20ek.c @@ -24,7 +24,12 @@ #include <linux/platform_device.h> #include <linux/spi/spi.h> #include <linux/spi/at73c213.h> +#include <linux/gpio_keys.h> +#include <linux/input.h> #include <linux/clk.h> +#include <linux/regulator/machine.h> +#include <linux/regulator/fixed.h> +#include <linux/regulator/consumer.h> #include <mach/hardware.h> #include <asm/setup.h> @@ -42,13 +47,25 @@ #include "sam9_smc.h" #include "generic.h" +/* + * board revision encoding + * bit 0: + * 0 => 1 sd/mmc slot + * 1 => 2 sd/mmc slots connectors (board from revision C) + */ +#define HAVE_2MMC (1 << 0) +static int inline ek_have_2mmc(void) +{ + return machine_is_at91sam9g20ek_2mmc() || (system_rev & HAVE_2MMC); +} + static void __init ek_map_io(void) { /* Initialize processor: 18.432 MHz crystal */ at91sam9260_initialize(18432000); - /* DGBU on ttyS0. (Rx & Tx only) */ + /* DBGU on ttyS0. (Rx & Tx only) */ at91_register_uart(0, 0, 0); /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ @@ -89,7 +106,7 @@ static struct at91_udc_data __initdata ek_udc_data = { * SPI devices. */ static struct spi_board_info ek_spi_devices[] = { -#if !defined(CONFIG_MMC_AT91) +#if !(defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_AT91)) { /* DataFlash chip */ .modalias = "mtd_dataflash", .chip_select = 1, @@ -116,6 +133,13 @@ static struct at91_eth_data __initdata ek_macb_data = { .is_rmii = 1, }; +static void __init ek_add_device_macb(void) +{ + if (ek_have_2mmc()) + ek_macb_data.phy_irq_pin = AT91_PIN_PB0; + + at91_add_device_eth(&ek_macb_data); +} /* * NAND flash @@ -193,13 +217,36 @@ static void __init ek_add_device_nand(void) /* * MCI (SD/MMC) - * det_pin, wp_pin and vcc_pin are not connected + * wp_pin and vcc_pin are not connected */ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) +static struct mci_platform_data __initdata ek_mmc_data = { + .slot[1] = { + .bus_width = 4, + .detect_pin = AT91_PIN_PC9, + }, + +}; +#else static struct at91_mmc_data __initdata ek_mmc_data = { - .slot_b = 1, + .slot_b = 1, /* Only one slot so use slot B */ .wire4 = 1, + .det_pin = AT91_PIN_PC9, }; +#endif +static void __init ek_add_device_mmc(void) +{ +#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) + if (ek_have_2mmc()) { + ek_mmc_data.slot[0].bus_width = 4; + ek_mmc_data.slot[0].detect_pin = AT91_PIN_PC2; + } + at91_add_device_mci(0, &ek_mmc_data); +#else + at91_add_device_mmc(0, &ek_mmc_data); +#endif +} /* * LEDs @@ -218,10 +265,112 @@ static struct gpio_led ek_leds[] = { } }; -static struct i2c_board_info __initdata ek_i2c_devices[] = { +static void __init ek_add_device_gpio_leds(void) +{ + if (ek_have_2mmc()) { + ek_leds[0].gpio = AT91_PIN_PB8; + ek_leds[1].gpio = AT91_PIN_PB9; + } + + at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); +} + +/* + * GPIO Buttons + */ +#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) +static struct gpio_keys_button ek_buttons[] = { + { + .gpio = AT91_PIN_PA30, + .code = BTN_3, + .desc = "Button 3", + .active_low = 1, + .wakeup = 1, + }, { - I2C_BOARD_INFO("24c512", 0x50), + .gpio = AT91_PIN_PA31, + .code = BTN_4, + .desc = "Button 4", + .active_low = 1, + .wakeup = 1, + } +}; + +static struct gpio_keys_platform_data ek_button_data = { + .buttons = ek_buttons, + .nbuttons = ARRAY_SIZE(ek_buttons), +}; + +static struct platform_device ek_button_device = { + .name = "gpio-keys", + .id = -1, + .num_resources = 0, + .dev = { + .platform_data = &ek_button_data, + } +}; + +static void __init ek_add_device_buttons(void) +{ + at91_set_gpio_input(AT91_PIN_PA30, 1); /* btn3 */ + at91_set_deglitch(AT91_PIN_PA30, 1); + at91_set_gpio_input(AT91_PIN_PA31, 1); /* btn4 */ + at91_set_deglitch(AT91_PIN_PA31, 1); + + platform_device_register(&ek_button_device); +} +#else +static void __init ek_add_device_buttons(void) {} +#endif + +#if defined(CONFIG_REGULATOR_FIXED_VOLTAGE) || defined(CONFIG_REGULATOR_FIXED_VOLTAGE_MODULE) +static struct regulator_consumer_supply ek_audio_consumer_supplies[] = { + REGULATOR_SUPPLY("AVDD", "0-001b"), + REGULATOR_SUPPLY("HPVDD", "0-001b"), + REGULATOR_SUPPLY("DBVDD", "0-001b"), + REGULATOR_SUPPLY("DCVDD", "0-001b"), +}; + +static struct regulator_init_data ek_avdd_reg_init_data = { + .constraints = { + .name = "3V3", + .valid_ops_mask = REGULATOR_CHANGE_STATUS, }, + .consumer_supplies = ek_audio_consumer_supplies, + .num_consumer_supplies = ARRAY_SIZE(ek_audio_consumer_supplies), +}; + +static struct fixed_voltage_config ek_vdd_pdata = { + .supply_name = "board-3V3", + .microvolts = 3300000, + .gpio = -EINVAL, + .enabled_at_boot = 0, + .init_data = &ek_avdd_reg_init_data, +}; +static struct platform_device ek_voltage_regulator = { + .name = "reg-fixed-voltage", + .id = -1, + .num_resources = 0, + .dev = { + .platform_data = &ek_vdd_pdata, + }, +}; +static void __init ek_add_regulators(void) +{ + platform_device_register(&ek_voltage_regulator); +} +#else +static void __init ek_add_regulators(void) {} +#endif + + +static struct i2c_board_info __initdata ek_i2c_devices[] = { + { + I2C_BOARD_INFO("24c512", 0x50) + }, + { + I2C_BOARD_INFO("wm8731", 0x1b) + }, }; @@ -238,13 +387,17 @@ static void __init ek_board_init(void) /* NAND */ ek_add_device_nand(); /* Ethernet */ - at91_add_device_eth(&ek_macb_data); + ek_add_device_macb(); + /* Regulators */ + ek_add_regulators(); /* MMC */ - at91_add_device_mmc(0, &ek_mmc_data); + ek_add_device_mmc(); /* I2C */ at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices)); /* LEDs */ - at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); + ek_add_device_gpio_leds(); + /* Push Buttons */ + ek_add_device_buttons(); /* PCK0 provides MCLK to the WM8731 */ at91_set_B_periph(AT91_PIN_PC1, 0); /* SSC (for WM8731) */ @@ -253,8 +406,15 @@ static void __init ek_board_init(void) MACHINE_START(AT91SAM9G20EK, "Atmel AT91SAM9G20-EK") /* Maintainer: Atmel */ - .phys_io = AT91_BASE_SYS, - .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91sam926x_timer, + .map_io = ek_map_io, + .init_irq = ek_init_irq, + .init_machine = ek_board_init, +MACHINE_END + +MACHINE_START(AT91SAM9G20EK_2MMC, "Atmel AT91SAM9G20-EK 2 MMC Slot Mod") + /* Maintainer: Atmel */ .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91sam926x_timer, .map_io = ek_map_io, |