diff options
Diffstat (limited to 'arch/arm')
148 files changed, 699 insertions, 552 deletions
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 5b714695b01b..1cacda426a0e 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -49,7 +49,6 @@ config ARM select HAVE_REGS_AND_STACK_ACCESS_API select HAVE_SYSCALL_TRACEPOINTS select HAVE_UID16 - select HAVE_VIRT_TO_BUS select KTIME_SCALAR select PERF_USE_VMALLOC select RTC_LIB @@ -556,7 +555,6 @@ config ARCH_IXP4XX config ARCH_DOVE bool "Marvell Dove" select ARCH_REQUIRE_GPIOLIB - select COMMON_CLK_DOVE select CPU_V7 select GENERIC_CLOCKEVENTS select MIGHT_HAVE_PCI @@ -744,6 +742,7 @@ config ARCH_RPC select NEED_MACH_IO_H select NEED_MACH_MEMORY_H select NO_IOPORT + select VIRT_TO_BUS help On the Acorn Risc-PC, Linux can support the internal IDE disk and CD-ROM interface, serial and parallel port, and the floppy drive. @@ -879,6 +878,7 @@ config ARCH_SHARK select ISA_DMA select NEED_MACH_MEMORY_H select PCI + select VIRT_TO_BUS select ZONE_DMA help Support for the StrongARM based Digital DNARD machine, also known @@ -1006,12 +1006,12 @@ config ARCH_MULTI_V4_V5 bool config ARCH_MULTI_V6 - bool "ARMv6 based platforms (ARM11, Scorpion, ...)" + bool "ARMv6 based platforms (ARM11)" select ARCH_MULTI_V6_V7 select CPU_V6 config ARCH_MULTI_V7 - bool "ARMv7 based platforms (Cortex-A, PJ4, Krait)" + bool "ARMv7 based platforms (Cortex-A, PJ4, Scorpion, Krait)" default y select ARCH_MULTI_V6_V7 select ARCH_VEXPRESS @@ -1183,9 +1183,9 @@ config ARM_NR_BANKS default 8 config IWMMXT - bool "Enable iWMMXt support" + bool "Enable iWMMXt support" if !CPU_PJ4 depends on CPU_XSCALE || CPU_XSC3 || CPU_MOHAWK || CPU_PJ4 - default y if PXA27x || PXA3xx || ARCH_MMP + default y if PXA27x || PXA3xx || ARCH_MMP || CPU_PJ4 help Enable support for iWMMXt context switching at run time if running on a CPU that supports it. @@ -1439,6 +1439,16 @@ config ARM_ERRATA_775420 to deadlock. This workaround puts DSB before executing ISB if an abort may occur on cache maintenance. +config ARM_ERRATA_798181 + bool "ARM errata: TLBI/DSB failure on Cortex-A15" + depends on CPU_V7 && SMP + help + On Cortex-A15 (r0p0..r3p2) the TLBI*IS/DSB operations are not + adequately shooting down all use of the old entries. This + option enables the Linux kernel workaround for this erratum + which sends an IPI to the CPUs that are running the same ASID + as the one being invalidated. + endmenu source "arch/arm/common/Kconfig" @@ -1462,10 +1472,6 @@ config ISA_DMA bool select ISA_DMA_API -config ARCH_NO_VIRT_TO_BUS - def_bool y - depends on !ARCH_RPC && !ARCH_NETWINDER && !ARCH_SHARK - # Select ISA DMA interface config ISA_DMA_API bool @@ -1657,13 +1663,16 @@ config LOCAL_TIMERS accounting to be spread across the timer interval, preventing a "thundering herd" at every timer tick. +# The GPIO number here must be sorted by descending number. In case of +# a multiplatform kernel, we just want the highest value required by the +# selected platforms. config ARCH_NR_GPIO int default 1024 if ARCH_SHMOBILE || ARCH_TEGRA - default 355 if ARCH_U8500 - default 264 if MACH_H4700 default 512 if SOC_OMAP5 + default 355 if ARCH_U8500 default 288 if ARCH_VT8500 || ARCH_SUNXI + default 264 if MACH_H4700 default 0 help Maximum number of GPIOs in the system. @@ -1887,8 +1896,9 @@ config XEN_DOM0 config XEN bool "Xen guest support on ARM (EXPERIMENTAL)" - depends on ARM && OF + depends on ARM && AEABI && OF depends on CPU_V7 && !CPU_V6 + depends on !GENERIC_ATOMIC64 help Say Y if you want to run Linux in a Virtual Machine on Xen on ARM. diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug index acddddac7ee4..9b31f4311ea2 100644 --- a/arch/arm/Kconfig.debug +++ b/arch/arm/Kconfig.debug @@ -492,9 +492,10 @@ config DEBUG_IMX_UART_PORT DEBUG_IMX31_UART || \ DEBUG_IMX35_UART || \ DEBUG_IMX51_UART || \ - DEBUG_IMX50_IMX53_UART || \ + DEBUG_IMX53_UART || \ DEBUG_IMX6Q_UART default 1 + depends on ARCH_MXC help Choose UART port on which kernel low-level debug messages should be output. diff --git a/arch/arm/boot/Makefile b/arch/arm/boot/Makefile index 71768b8a1ab9..84aa2caf07ed 100644 --- a/arch/arm/boot/Makefile +++ b/arch/arm/boot/Makefile @@ -115,4 +115,4 @@ i: $(CONFIG_SHELL) $(srctree)/$(src)/install.sh $(KERNELRELEASE) \ $(obj)/Image System.map "$(INSTALL_PATH)" -subdir- := bootp compressed +subdir- := bootp compressed dts diff --git a/arch/arm/boot/dts/armada-370-mirabox.dts b/arch/arm/boot/dts/armada-370-mirabox.dts index dd0c57dd9f30..3234875824dc 100644 --- a/arch/arm/boot/dts/armada-370-mirabox.dts +++ b/arch/arm/boot/dts/armada-370-mirabox.dts @@ -54,7 +54,7 @@ }; mvsdio@d00d4000 { - pinctrl-0 = <&sdio_pins2>; + pinctrl-0 = <&sdio_pins3>; pinctrl-names = "default"; status = "okay"; /* diff --git a/arch/arm/boot/dts/armada-370-rd.dts b/arch/arm/boot/dts/armada-370-rd.dts index f8e4855bc9a5..070bba4f2585 100644 --- a/arch/arm/boot/dts/armada-370-rd.dts +++ b/arch/arm/boot/dts/armada-370-rd.dts @@ -64,5 +64,13 @@ status = "okay"; /* No CD or WP GPIOs */ }; + + usb@d0050000 { + status = "okay"; + }; + + usb@d0051000 { + status = "okay"; + }; }; }; diff --git a/arch/arm/boot/dts/armada-370-xp.dtsi b/arch/arm/boot/dts/armada-370-xp.dtsi index 6f1acc75e155..5b708208b607 100644 --- a/arch/arm/boot/dts/armada-370-xp.dtsi +++ b/arch/arm/boot/dts/armada-370-xp.dtsi @@ -31,7 +31,6 @@ mpic: interrupt-controller@d0020000 { compatible = "marvell,mpic"; #interrupt-cells = <1>; - #address-cells = <1>; #size-cells = <1>; interrupt-controller; }; @@ -54,7 +53,7 @@ reg = <0xd0012000 0x100>; reg-shift = <2>; interrupts = <41>; - reg-io-width = <4>; + reg-io-width = <1>; status = "disabled"; }; serial@d0012100 { @@ -62,7 +61,7 @@ reg = <0xd0012100 0x100>; reg-shift = <2>; interrupts = <42>; - reg-io-width = <4>; + reg-io-width = <1>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/armada-370.dtsi b/arch/arm/boot/dts/armada-370.dtsi index 8188d138020e..a195debb67d3 100644 --- a/arch/arm/boot/dts/armada-370.dtsi +++ b/arch/arm/boot/dts/armada-370.dtsi @@ -59,6 +59,12 @@ "mpp50", "mpp51", "mpp52"; marvell,function = "sd0"; }; + + sdio_pins3: sdio-pins3 { + marvell,pins = "mpp48", "mpp49", "mpp50", + "mpp51", "mpp52", "mpp53"; + marvell,function = "sd0"; + }; }; gpio0: gpio@d0018100 { diff --git a/arch/arm/boot/dts/armada-xp.dtsi b/arch/arm/boot/dts/armada-xp.dtsi index 1443949c165e..ca00d8326c87 100644 --- a/arch/arm/boot/dts/armada-xp.dtsi +++ b/arch/arm/boot/dts/armada-xp.dtsi @@ -46,7 +46,7 @@ reg = <0xd0012200 0x100>; reg-shift = <2>; interrupts = <43>; - reg-io-width = <4>; + reg-io-width = <1>; status = "disabled"; }; serial@d0012300 { @@ -54,7 +54,7 @@ reg = <0xd0012300 0x100>; reg-shift = <2>; interrupts = <44>; - reg-io-width = <4>; + reg-io-width = <1>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi index aa98e641931f..a98c0d50fbbe 100644 --- a/arch/arm/boot/dts/at91sam9x5.dtsi +++ b/arch/arm/boot/dts/at91sam9x5.dtsi @@ -238,8 +238,32 @@ nand { pinctrl_nand: nand-0 { atmel,pins = - <3 4 0x0 0x1 /* PD5 gpio RDY pin pull_up */ - 3 5 0x0 0x1>; /* PD4 gpio enable pin pull_up */ + <3 0 0x1 0x0 /* PD0 periph A Read Enable */ + 3 1 0x1 0x0 /* PD1 periph A Write Enable */ + 3 2 0x1 0x0 /* PD2 periph A Address Latch Enable */ + 3 3 0x1 0x0 /* PD3 periph A Command Latch Enable */ + 3 4 0x0 0x1 /* PD4 gpio Chip Enable pin pull_up */ + 3 5 0x0 0x1 /* PD5 gpio RDY/BUSY pin pull_up */ + 3 6 0x1 0x0 /* PD6 periph A Data bit 0 */ + 3 7 0x1 0x0 /* PD7 periph A Data bit 1 */ + 3 8 0x1 0x0 /* PD8 periph A Data bit 2 */ + 3 9 0x1 0x0 /* PD9 periph A Data bit 3 */ + 3 10 0x1 0x0 /* PD10 periph A Data bit 4 */ + 3 11 0x1 0x0 /* PD11 periph A Data bit 5 */ + 3 12 0x1 0x0 /* PD12 periph A Data bit 6 */ + 3 13 0x1 0x0>; /* PD13 periph A Data bit 7 */ + }; + + pinctrl_nand_16bits: nand_16bits-0 { + atmel,pins = + <3 14 0x1 0x0 /* PD14 periph A Data bit 8 */ + 3 15 0x1 0x0 /* PD15 periph A Data bit 9 */ + 3 16 0x1 0x0 /* PD16 periph A Data bit 10 */ + 3 17 0x1 0x0 /* PD17 periph A Data bit 11 */ + 3 18 0x1 0x0 /* PD18 periph A Data bit 12 */ + 3 19 0x1 0x0 /* PD19 periph A Data bit 13 */ + 3 20 0x1 0x0 /* PD20 periph A Data bit 14 */ + 3 21 0x1 0x0>; /* PD21 periph A Data bit 15 */ }; }; diff --git a/arch/arm/boot/dts/bcm2835.dtsi b/arch/arm/boot/dts/bcm2835.dtsi index 4bf2a8774aa7..7e0481e2441a 100644 --- a/arch/arm/boot/dts/bcm2835.dtsi +++ b/arch/arm/boot/dts/bcm2835.dtsi @@ -105,7 +105,7 @@ compatible = "fixed-clock"; reg = <1>; #clock-cells = <0>; - clock-frequency = <150000000>; + clock-frequency = <250000000>; }; }; }; diff --git a/arch/arm/boot/dts/dbx5x0.dtsi b/arch/arm/boot/dts/dbx5x0.dtsi index 69140ba99f46..aaa63d0a8096 100644 --- a/arch/arm/boot/dts/dbx5x0.dtsi +++ b/arch/arm/boot/dts/dbx5x0.dtsi @@ -191,8 +191,8 @@ prcmu: prcmu@80157000 { compatible = "stericsson,db8500-prcmu"; - reg = <0x80157000 0x1000>; - reg-names = "prcmu"; + reg = <0x80157000 0x1000>, <0x801b0000 0x8000>, <0x801b8000 0x1000>; + reg-names = "prcmu", "prcmu-tcpm", "prcmu-tcdm"; interrupts = <0 47 0x4>; #address-cells = <1>; #size-cells = <1>; @@ -319,9 +319,8 @@ }; }; - ab8500@5 { + ab8500 { compatible = "stericsson,ab8500"; - reg = <5>; /* mailbox 5 is i2c */ interrupt-parent = <&intc>; interrupts = <0 40 0x4>; interrupt-controller; diff --git a/arch/arm/boot/dts/dove.dtsi b/arch/arm/boot/dts/dove.dtsi index 67dbe20868a2..f7509cafc377 100644 --- a/arch/arm/boot/dts/dove.dtsi +++ b/arch/arm/boot/dts/dove.dtsi @@ -197,6 +197,11 @@ status = "disabled"; }; + rtc@d8500 { + compatible = "marvell,orion-rtc"; + reg = <0xd8500 0x20>; + }; + crypto: crypto@30000 { compatible = "marvell,orion-crypto"; reg = <0x30000 0x10000>, diff --git a/arch/arm/boot/dts/exynos4.dtsi b/arch/arm/boot/dts/exynos4.dtsi index e1347fceb5bc..1a62bcf18aa3 100644 --- a/arch/arm/boot/dts/exynos4.dtsi +++ b/arch/arm/boot/dts/exynos4.dtsi @@ -275,18 +275,27 @@ compatible = "arm,pl330", "arm,primecell"; reg = <0x12680000 0x1000>; interrupts = <0 35 0>; + #dma-cells = <1>; + #dma-channels = <8>; + #dma-requests = <32>; }; pdma1: pdma@12690000 { compatible = "arm,pl330", "arm,primecell"; reg = <0x12690000 0x1000>; interrupts = <0 36 0>; + #dma-cells = <1>; + #dma-channels = <8>; + #dma-requests = <32>; }; mdma1: mdma@12850000 { compatible = "arm,pl330", "arm,primecell"; reg = <0x12850000 0x1000>; interrupts = <0 34 0>; + #dma-cells = <1>; + #dma-channels = <8>; + #dma-requests = <1>; }; }; }; diff --git a/arch/arm/boot/dts/exynos5440.dtsi b/arch/arm/boot/dts/exynos5440.dtsi index 5f3562ad6746..9a99755920c0 100644 --- a/arch/arm/boot/dts/exynos5440.dtsi +++ b/arch/arm/boot/dts/exynos5440.dtsi @@ -142,12 +142,18 @@ compatible = "arm,pl330", "arm,primecell"; reg = <0x120000 0x1000>; interrupts = <0 34 0>; + #dma-cells = <1>; + #dma-channels = <8>; + #dma-requests = <32>; }; pdma1: pdma@121B0000 { compatible = "arm,pl330", "arm,primecell"; reg = <0x121000 0x1000>; interrupts = <0 35 0>; + #dma-cells = <1>; + #dma-channels = <8>; + #dma-requests = <32>; }; }; diff --git a/arch/arm/boot/dts/href.dtsi b/arch/arm/boot/dts/href.dtsi index 592fb9dc35bd..379128eb9d98 100644 --- a/arch/arm/boot/dts/href.dtsi +++ b/arch/arm/boot/dts/href.dtsi @@ -221,7 +221,7 @@ }; }; - ab8500@5 { + ab8500 { ab8500-regulators { ab8500_ldo_aux1_reg: ab8500_ldo_aux1 { regulator-name = "V-DISPLAY"; diff --git a/arch/arm/boot/dts/hrefv60plus.dts b/arch/arm/boot/dts/hrefv60plus.dts index 55f4191a626e..2b587a74b813 100644 --- a/arch/arm/boot/dts/hrefv60plus.dts +++ b/arch/arm/boot/dts/hrefv60plus.dts @@ -158,7 +158,7 @@ }; }; - ab8500@5 { + ab8500 { ab8500-regulators { ab8500_ldo_aux1_reg: ab8500_ldo_aux1 { regulator-name = "V-DISPLAY"; diff --git a/arch/arm/boot/dts/imx28-m28evk.dts b/arch/arm/boot/dts/imx28-m28evk.dts index 6ce3d17c3a29..fd36e1cca104 100644 --- a/arch/arm/boot/dts/imx28-m28evk.dts +++ b/arch/arm/boot/dts/imx28-m28evk.dts @@ -152,7 +152,6 @@ i2c0: i2c@80058000 { pinctrl-names = "default"; pinctrl-0 = <&i2c0_pins_a>; - clock-frequency = <400000>; status = "okay"; sgtl5000: codec@0a { diff --git a/arch/arm/boot/dts/imx28-sps1.dts b/arch/arm/boot/dts/imx28-sps1.dts index e6cde8aa7fff..6c6a5442800a 100644 --- a/arch/arm/boot/dts/imx28-sps1.dts +++ b/arch/arm/boot/dts/imx28-sps1.dts @@ -70,7 +70,6 @@ i2c0: i2c@80058000 { pinctrl-names = "default"; pinctrl-0 = <&i2c0_pins_a>; - clock-frequency = <400000>; status = "okay"; rtc: rtc@51 { diff --git a/arch/arm/boot/dts/imx53-mba53.dts b/arch/arm/boot/dts/imx53-mba53.dts index e54fffd48369..468c0a1d48d9 100644 --- a/arch/arm/boot/dts/imx53-mba53.dts +++ b/arch/arm/boot/dts/imx53-mba53.dts @@ -42,10 +42,9 @@ fsl,pins = <689 0x10000 /* DISP1_DRDY */ 482 0x10000 /* DISP1_HSYNC */ 489 0x10000 /* DISP1_VSYNC */ - 684 0x10000 /* DISP1_DAT_0 */ 515 0x10000 /* DISP1_DAT_22 */ 523 0x10000 /* DISP1_DAT_23 */ - 543 0x10000 /* DISP1_DAT_21 */ + 545 0x10000 /* DISP1_DAT_21 */ 553 0x10000 /* DISP1_DAT_20 */ 558 0x10000 /* DISP1_DAT_19 */ 564 0x10000 /* DISP1_DAT_18 */ diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi index 06ec460b4581..281a223591ff 100644 --- a/arch/arm/boot/dts/imx6qdl.dtsi +++ b/arch/arm/boot/dts/imx6qdl.dtsi @@ -91,6 +91,7 @@ compatible = "arm,cortex-a9-twd-timer"; reg = <0x00a00600 0x20>; interrupts = <1 13 0xf01>; + clocks = <&clks 15>; }; L2: l2-cache@00a02000 { diff --git a/arch/arm/boot/dts/kirkwood-dns320.dts b/arch/arm/boot/dts/kirkwood-dns320.dts index 5bb0bf39d3b8..c9c44b2f62d7 100644 --- a/arch/arm/boot/dts/kirkwood-dns320.dts +++ b/arch/arm/boot/dts/kirkwood-dns320.dts @@ -42,12 +42,10 @@ ocp@f1000000 { serial@12000 { - clock-frequency = <166666667>; status = "okay"; }; serial@12100 { - clock-frequency = <166666667>; status = "okay"; }; }; diff --git a/arch/arm/boot/dts/kirkwood-dns325.dts b/arch/arm/boot/dts/kirkwood-dns325.dts index d430713ea9b9..e4e4930dc5cf 100644 --- a/arch/arm/boot/dts/kirkwood-dns325.dts +++ b/arch/arm/boot/dts/kirkwood-dns325.dts @@ -50,7 +50,6 @@ }; }; serial@12000 { - clock-frequency = <200000000>; status = "okay"; }; }; diff --git a/arch/arm/boot/dts/kirkwood-dockstar.dts b/arch/arm/boot/dts/kirkwood-dockstar.dts index 2e3dd34e21a5..0196cf6b0ef2 100644 --- a/arch/arm/boot/dts/kirkwood-dockstar.dts +++ b/arch/arm/boot/dts/kirkwood-dockstar.dts @@ -37,7 +37,6 @@ }; }; serial@12000 { - clock-frequency = <200000000>; status = "ok"; }; diff --git a/arch/arm/boot/dts/kirkwood-dreamplug.dts b/arch/arm/boot/dts/kirkwood-dreamplug.dts index ef2d8c705709..289e51d86372 100644 --- a/arch/arm/boot/dts/kirkwood-dreamplug.dts +++ b/arch/arm/boot/dts/kirkwood-dreamplug.dts @@ -38,7 +38,6 @@ }; }; serial@12000 { - clock-frequency = <200000000>; status = "ok"; }; diff --git a/arch/arm/boot/dts/kirkwood-goflexnet.dts b/arch/arm/boot/dts/kirkwood-goflexnet.dts index 1b133e0c566e..c3573be7b92c 100644 --- a/arch/arm/boot/dts/kirkwood-goflexnet.dts +++ b/arch/arm/boot/dts/kirkwood-goflexnet.dts @@ -73,11 +73,11 @@ }; }; serial@12000 { - clock-frequency = <200000000>; status = "ok"; }; nand@3000000 { + chip-delay = <40>; status = "okay"; partition@0 { diff --git a/arch/arm/boot/dts/kirkwood-ib62x0.dts b/arch/arm/boot/dts/kirkwood-ib62x0.dts index 71902da33d63..5335b1aa8601 100644 --- a/arch/arm/boot/dts/kirkwood-ib62x0.dts +++ b/arch/arm/boot/dts/kirkwood-ib62x0.dts @@ -51,7 +51,6 @@ }; }; serial@12000 { - clock-frequency = <200000000>; status = "okay"; }; diff --git a/arch/arm/boot/dts/kirkwood-iconnect.dts b/arch/arm/boot/dts/kirkwood-iconnect.dts index 504f16be8b54..12ccf74ac3c4 100644 --- a/arch/arm/boot/dts/kirkwood-iconnect.dts +++ b/arch/arm/boot/dts/kirkwood-iconnect.dts @@ -78,7 +78,6 @@ }; }; serial@12000 { - clock-frequency = <200000000>; status = "ok"; }; diff --git a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts index 6cae4599c4b3..3694e94f6e99 100644 --- a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts +++ b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts @@ -96,11 +96,11 @@ marvell,function = "gpio"; }; pmx_led_rebuild_brt_ctrl_1: pmx-led-rebuild-brt-ctrl-1 { - marvell,pins = "mpp44"; + marvell,pins = "mpp46"; marvell,function = "gpio"; }; pmx_led_rebuild_brt_ctrl_2: pmx-led-rebuild-brt-ctrl-2 { - marvell,pins = "mpp45"; + marvell,pins = "mpp47"; marvell,function = "gpio"; }; @@ -115,7 +115,6 @@ }; serial@12000 { - clock-frequency = <200000000>; status = "ok"; }; @@ -158,14 +157,14 @@ gpios = <&gpio0 16 0>; linux,default-trigger = "default-on"; }; - health_led1 { + rebuild_led { + label = "status:white:rebuild_led"; + gpios = <&gpio1 4 0>; + }; + health_led { label = "status:red:health_led"; gpios = <&gpio1 5 0>; }; - health_led2 { - label = "status:white:health_led"; - gpios = <&gpio1 4 0>; - }; backup_led { label = "status:blue:backup_led"; gpios = <&gpio0 15 0>; diff --git a/arch/arm/boot/dts/kirkwood-km_kirkwood.dts b/arch/arm/boot/dts/kirkwood-km_kirkwood.dts index 8db3123ac80f..5bbd0542cdd3 100644 --- a/arch/arm/boot/dts/kirkwood-km_kirkwood.dts +++ b/arch/arm/boot/dts/kirkwood-km_kirkwood.dts @@ -34,7 +34,6 @@ }; serial@12000 { - clock-frequency = <200000000>; status = "ok"; }; diff --git a/arch/arm/boot/dts/kirkwood-lschlv2.dts b/arch/arm/boot/dts/kirkwood-lschlv2.dts index 9510c9ea666c..9f55d95f35f5 100644 --- a/arch/arm/boot/dts/kirkwood-lschlv2.dts +++ b/arch/arm/boot/dts/kirkwood-lschlv2.dts @@ -13,7 +13,6 @@ ocp@f1000000 { serial@12000 { - clock-frequency = <166666667>; status = "okay"; }; }; diff --git a/arch/arm/boot/dts/kirkwood-lsxhl.dts b/arch/arm/boot/dts/kirkwood-lsxhl.dts index 739019c4cba9..5c84c118ed8d 100644 --- a/arch/arm/boot/dts/kirkwood-lsxhl.dts +++ b/arch/arm/boot/dts/kirkwood-lsxhl.dts @@ -13,7 +13,6 @@ ocp@f1000000 { serial@12000 { - clock-frequency = <200000000>; status = "okay"; }; }; diff --git a/arch/arm/boot/dts/kirkwood-mplcec4.dts b/arch/arm/boot/dts/kirkwood-mplcec4.dts index 662dfd81b1ce..758824118a9a 100644 --- a/arch/arm/boot/dts/kirkwood-mplcec4.dts +++ b/arch/arm/boot/dts/kirkwood-mplcec4.dts @@ -90,7 +90,6 @@ }; serial@12000 { - clock-frequency = <200000000>; status = "ok"; }; diff --git a/arch/arm/boot/dts/kirkwood-ns2-common.dtsi b/arch/arm/boot/dts/kirkwood-ns2-common.dtsi index e8e7ecef1650..6affd924fe11 100644 --- a/arch/arm/boot/dts/kirkwood-ns2-common.dtsi +++ b/arch/arm/boot/dts/kirkwood-ns2-common.dtsi @@ -23,7 +23,6 @@ }; serial@12000 { - clock-frequency = <166666667>; status = "okay"; }; diff --git a/arch/arm/boot/dts/kirkwood-nsa310.dts b/arch/arm/boot/dts/kirkwood-nsa310.dts index 3a178cf708d7..a7412b937a8a 100644 --- a/arch/arm/boot/dts/kirkwood-nsa310.dts +++ b/arch/arm/boot/dts/kirkwood-nsa310.dts @@ -117,7 +117,6 @@ }; serial@12000 { - clock-frequency = <200000000>; status = "ok"; }; diff --git a/arch/arm/boot/dts/kirkwood-openblocks_a6.dts b/arch/arm/boot/dts/kirkwood-openblocks_a6.dts index ede7fe0d7a87..d27f7245f8e7 100644 --- a/arch/arm/boot/dts/kirkwood-openblocks_a6.dts +++ b/arch/arm/boot/dts/kirkwood-openblocks_a6.dts @@ -18,12 +18,10 @@ ocp@f1000000 { serial@12000 { - clock-frequency = <200000000>; status = "ok"; }; serial@12100 { - clock-frequency = <200000000>; status = "ok"; }; diff --git a/arch/arm/boot/dts/kirkwood-topkick.dts b/arch/arm/boot/dts/kirkwood-topkick.dts index 842ff95d60df..66eb45b00b25 100644 --- a/arch/arm/boot/dts/kirkwood-topkick.dts +++ b/arch/arm/boot/dts/kirkwood-topkick.dts @@ -108,7 +108,6 @@ }; serial@12000 { - clock-frequency = <200000000>; status = "ok"; }; diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi index 2c738d9dc82a..fada7e6d24d8 100644 --- a/arch/arm/boot/dts/kirkwood.dtsi +++ b/arch/arm/boot/dts/kirkwood.dtsi @@ -38,6 +38,7 @@ interrupt-controller; #interrupt-cells = <2>; interrupts = <35>, <36>, <37>, <38>; + clocks = <&gate_clk 7>; }; gpio1: gpio@10140 { @@ -49,6 +50,7 @@ interrupt-controller; #interrupt-cells = <2>; interrupts = <39>, <40>, <41>; + clocks = <&gate_clk 7>; }; serial@12000 { @@ -57,7 +59,6 @@ reg-shift = <2>; interrupts = <33>; clocks = <&gate_clk 7>; - /* set clock-frequency in board dts */ status = "disabled"; }; @@ -67,7 +68,6 @@ reg-shift = <2>; interrupts = <34>; clocks = <&gate_clk 7>; - /* set clock-frequency in board dts */ status = "disabled"; }; @@ -75,6 +75,7 @@ compatible = "marvell,kirkwood-rtc", "marvell,orion-rtc"; reg = <0x10300 0x20>; interrupts = <53>; + clocks = <&gate_clk 7>; }; spi@10600 { diff --git a/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts b/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts index 5a3a58b7e18f..0077fc8510b7 100644 --- a/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts +++ b/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts @@ -11,7 +11,7 @@ / { model = "LaCie Ethernet Disk mini V2"; - compatible = "lacie,ethernet-disk-mini-v2", "marvell-orion5x-88f5182", "marvell,orion5x"; + compatible = "lacie,ethernet-disk-mini-v2", "marvell,orion5x-88f5182", "marvell,orion5x"; memory { reg = <0x00000000 0x4000000>; /* 64 MB */ diff --git a/arch/arm/boot/dts/orion5x.dtsi b/arch/arm/boot/dts/orion5x.dtsi index 8aad00f81ed9..f7bec3b1ba32 100644 --- a/arch/arm/boot/dts/orion5x.dtsi +++ b/arch/arm/boot/dts/orion5x.dtsi @@ -13,6 +13,9 @@ compatible = "marvell,orion5x"; interrupt-parent = <&intc>; + aliases { + gpio0 = &gpio0; + }; intc: interrupt-controller { compatible = "marvell,orion-intc", "marvell,intc"; interrupt-controller; @@ -32,7 +35,9 @@ #gpio-cells = <2>; gpio-controller; reg = <0x10100 0x40>; - ngpio = <32>; + ngpios = <32>; + interrupt-controller; + #interrupt-cells = <2>; interrupts = <6>, <7>, <8>, <9>; }; @@ -91,7 +96,7 @@ reg = <0x90000 0x10000>, <0xf2200000 0x800>; reg-names = "regs", "sram"; - interrupts = <22>; + interrupts = <28>; status = "okay"; }; }; diff --git a/arch/arm/boot/dts/snowball.dts b/arch/arm/boot/dts/snowball.dts index 27f31a5fa494..d3ec32f6b790 100644 --- a/arch/arm/boot/dts/snowball.dts +++ b/arch/arm/boot/dts/snowball.dts @@ -298,7 +298,7 @@ }; }; - ab8500@5 { + ab8500 { ab8500-regulators { ab8500_ldo_aux1_reg: ab8500_ldo_aux1 { regulator-name = "V-DISPLAY"; diff --git a/arch/arm/boot/dts/socfpga.dtsi b/arch/arm/boot/dts/socfpga.dtsi index 936d2306e7e1..7e8769bd5977 100644 --- a/arch/arm/boot/dts/socfpga.dtsi +++ b/arch/arm/boot/dts/socfpga.dtsi @@ -75,6 +75,9 @@ compatible = "arm,pl330", "arm,primecell"; reg = <0xffe01000 0x1000>; interrupts = <0 180 4>; + #dma-cells = <1>; + #dma-channels = <8>; + #dma-requests = <32>; }; }; diff --git a/arch/arm/boot/dts/tegra20.dtsi b/arch/arm/boot/dts/tegra20.dtsi index 9a428931d042..3d3f64d2111a 100644 --- a/arch/arm/boot/dts/tegra20.dtsi +++ b/arch/arm/boot/dts/tegra20.dtsi @@ -118,6 +118,7 @@ compatible = "arm,cortex-a9-twd-timer"; reg = <0x50040600 0x20>; interrupts = <1 13 0x304>; + clocks = <&tegra_car 132>; }; intc: interrupt-controller { @@ -384,7 +385,7 @@ spi@7000d800 { compatible = "nvidia,tegra20-slink"; - reg = <0x7000d480 0x200>; + reg = <0x7000d800 0x200>; interrupts = <0 83 0x04>; nvidia,dma-request-selector = <&apbdma 17>; #address-cells = <1>; diff --git a/arch/arm/boot/dts/tegra30.dtsi b/arch/arm/boot/dts/tegra30.dtsi index 767803e1fd55..dbf46c272562 100644 --- a/arch/arm/boot/dts/tegra30.dtsi +++ b/arch/arm/boot/dts/tegra30.dtsi @@ -119,6 +119,7 @@ compatible = "arm,cortex-a9-twd-timer"; reg = <0x50040600 0x20>; interrupts = <1 13 0xf04>; + clocks = <&tegra_car 214>; }; intc: interrupt-controller { @@ -371,7 +372,7 @@ spi@7000d800 { compatible = "nvidia,tegra30-slink", "nvidia,tegra20-slink"; - reg = <0x7000d480 0x200>; + reg = <0x7000d800 0x200>; interrupts = <0 83 0x04>; nvidia,dma-request-selector = <&apbdma 17>; #address-cells = <1>; diff --git a/arch/arm/configs/mxs_defconfig b/arch/arm/configs/mxs_defconfig index fbbc5bb022d5..6a99e30f81d2 100644 --- a/arch/arm/configs/mxs_defconfig +++ b/arch/arm/configs/mxs_defconfig @@ -116,6 +116,7 @@ CONFIG_SND_SOC=y CONFIG_SND_MXS_SOC=y CONFIG_SND_SOC_MXS_SGTL5000=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_CHIPIDEA=y CONFIG_USB_CHIPIDEA_HOST=y CONFIG_USB_STORAGE=y diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig index b16bae2c9a60..bd07864f14a0 100644 --- a/arch/arm/configs/omap2plus_defconfig +++ b/arch/arm/configs/omap2plus_defconfig @@ -126,6 +126,8 @@ CONFIG_INPUT_MISC=y CONFIG_INPUT_TWL4030_PWRBUTTON=y CONFIG_VT_HW_CONSOLE_BINDING=y # CONFIG_LEGACY_PTYS is not set +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y CONFIG_SERIAL_8250_NR_UARTS=32 CONFIG_SERIAL_8250_EXTENDED=y CONFIG_SERIAL_8250_MANY_PORTS=y diff --git a/arch/arm/include/asm/delay.h b/arch/arm/include/asm/delay.h index 720799fd3a81..dff714d886d5 100644 --- a/arch/arm/include/asm/delay.h +++ b/arch/arm/include/asm/delay.h @@ -24,7 +24,7 @@ extern struct arm_delay_ops { void (*delay)(unsigned long); void (*const_udelay)(unsigned long); void (*udelay)(unsigned long); - bool const_clock; + unsigned long ticks_per_jiffy; } arm_delay_ops; #define __delay(n) arm_delay_ops.delay(n) diff --git a/arch/arm/include/asm/glue-cache.h b/arch/arm/include/asm/glue-cache.h index cca9f15704ed..ea289e1435e7 100644 --- a/arch/arm/include/asm/glue-cache.h +++ b/arch/arm/include/asm/glue-cache.h @@ -19,14 +19,6 @@ #undef _CACHE #undef MULTI_CACHE -#if defined(CONFIG_CPU_CACHE_V3) -# ifdef _CACHE -# define MULTI_CACHE 1 -# else -# define _CACHE v3 -# endif -#endif - #if defined(CONFIG_CPU_CACHE_V4) # ifdef _CACHE # define MULTI_CACHE 1 diff --git a/arch/arm/include/asm/hardware/iop3xx.h b/arch/arm/include/asm/hardware/iop3xx.h index 02fe2fbe2477..ed94b1a366ae 100644 --- a/arch/arm/include/asm/hardware/iop3xx.h +++ b/arch/arm/include/asm/hardware/iop3xx.h @@ -37,7 +37,7 @@ extern int iop3xx_get_init_atu(void); * IOP3XX processor registers */ #define IOP3XX_PERIPHERAL_PHYS_BASE 0xffffe000 -#define IOP3XX_PERIPHERAL_VIRT_BASE 0xfeffe000 +#define IOP3XX_PERIPHERAL_VIRT_BASE 0xfedfe000 #define IOP3XX_PERIPHERAL_SIZE 0x00002000 #define IOP3XX_PERIPHERAL_UPPER_PA (IOP3XX_PERIPHERAL_PHYS_BASE +\ IOP3XX_PERIPHERAL_SIZE - 1) diff --git a/arch/arm/include/asm/highmem.h b/arch/arm/include/asm/highmem.h index 8c5e828f484d..91b99abe7a95 100644 --- a/arch/arm/include/asm/highmem.h +++ b/arch/arm/include/asm/highmem.h @@ -41,6 +41,13 @@ extern void kunmap_high(struct page *page); #endif #endif +/* + * Needed to be able to broadcast the TLB invalidation for kmap. + */ +#ifdef CONFIG_ARM_ERRATA_798181 +#undef ARCH_NEEDS_KMAP_HIGH_GET +#endif + #ifdef ARCH_NEEDS_KMAP_HIGH_GET extern void *kmap_high_get(struct page *page); #else diff --git a/arch/arm/include/asm/mmu_context.h b/arch/arm/include/asm/mmu_context.h index 863a6611323c..a7b85e0d0cc1 100644 --- a/arch/arm/include/asm/mmu_context.h +++ b/arch/arm/include/asm/mmu_context.h @@ -27,6 +27,8 @@ void __check_vmalloc_seq(struct mm_struct *mm); void check_and_switch_context(struct mm_struct *mm, struct task_struct *tsk); #define init_new_context(tsk,mm) ({ atomic64_set(&mm->context.id, 0); 0; }) +DECLARE_PER_CPU(atomic64_t, active_asids); + #else /* !CONFIG_CPU_HAS_ASID */ #ifdef CONFIG_MMU diff --git a/arch/arm/include/asm/pgtable-3level.h b/arch/arm/include/asm/pgtable-3level.h index 6ef8afd1b64c..86b8fe398b95 100644 --- a/arch/arm/include/asm/pgtable-3level.h +++ b/arch/arm/include/asm/pgtable-3level.h @@ -111,7 +111,7 @@ #define L_PTE_S2_MT_WRITETHROUGH (_AT(pteval_t, 0xa) << 2) /* MemAttr[3:0] */ #define L_PTE_S2_MT_WRITEBACK (_AT(pteval_t, 0xf) << 2) /* MemAttr[3:0] */ #define L_PTE_S2_RDONLY (_AT(pteval_t, 1) << 6) /* HAP[1] */ -#define L_PTE_S2_RDWR (_AT(pteval_t, 2) << 6) /* HAP[2:1] */ +#define L_PTE_S2_RDWR (_AT(pteval_t, 3) << 6) /* HAP[2:1] */ /* * Hyp-mode PL2 PTE definitions for LPAE. diff --git a/arch/arm/include/asm/tlbflush.h b/arch/arm/include/asm/tlbflush.h index 4db8c8820f0d..ab865e65a84c 100644 --- a/arch/arm/include/asm/tlbflush.h +++ b/arch/arm/include/asm/tlbflush.h @@ -14,7 +14,6 @@ #include <asm/glue.h> -#define TLB_V3_PAGE (1 << 0) #define TLB_V4_U_PAGE (1 << 1) #define TLB_V4_D_PAGE (1 << 2) #define TLB_V4_I_PAGE (1 << 3) @@ -22,7 +21,6 @@ #define TLB_V6_D_PAGE (1 << 5) #define TLB_V6_I_PAGE (1 << 6) -#define TLB_V3_FULL (1 << 8) #define TLB_V4_U_FULL (1 << 9) #define TLB_V4_D_FULL (1 << 10) #define TLB_V4_I_FULL (1 << 11) @@ -52,7 +50,6 @@ * ============= * * We have the following to choose from: - * v3 - ARMv3 * v4 - ARMv4 without write buffer * v4wb - ARMv4 with write buffer without I TLB flush entry instruction * v4wbi - ARMv4 with write buffer with I TLB flush entry instruction @@ -330,7 +327,6 @@ static inline void local_flush_tlb_all(void) if (tlb_flag(TLB_WB)) dsb(); - tlb_op(TLB_V3_FULL, "c6, c0, 0", zero); tlb_op(TLB_V4_U_FULL | TLB_V6_U_FULL, "c8, c7, 0", zero); tlb_op(TLB_V4_D_FULL | TLB_V6_D_FULL, "c8, c6, 0", zero); tlb_op(TLB_V4_I_FULL | TLB_V6_I_FULL, "c8, c5, 0", zero); @@ -351,9 +347,8 @@ static inline void local_flush_tlb_mm(struct mm_struct *mm) if (tlb_flag(TLB_WB)) dsb(); - if (possible_tlb_flags & (TLB_V3_FULL|TLB_V4_U_FULL|TLB_V4_D_FULL|TLB_V4_I_FULL)) { + if (possible_tlb_flags & (TLB_V4_U_FULL|TLB_V4_D_FULL|TLB_V4_I_FULL)) { if (cpumask_test_cpu(get_cpu(), mm_cpumask(mm))) { - tlb_op(TLB_V3_FULL, "c6, c0, 0", zero); tlb_op(TLB_V4_U_FULL, "c8, c7, 0", zero); tlb_op(TLB_V4_D_FULL, "c8, c6, 0", zero); tlb_op(TLB_V4_I_FULL, "c8, c5, 0", zero); @@ -385,9 +380,8 @@ local_flush_tlb_page(struct vm_area_struct *vma, unsigned long uaddr) if (tlb_flag(TLB_WB)) dsb(); - if (possible_tlb_flags & (TLB_V3_PAGE|TLB_V4_U_PAGE|TLB_V4_D_PAGE|TLB_V4_I_PAGE|TLB_V4_I_FULL) && + if (possible_tlb_flags & (TLB_V4_U_PAGE|TLB_V4_D_PAGE|TLB_V4_I_PAGE|TLB_V4_I_FULL) && cpumask_test_cpu(smp_processor_id(), mm_cpumask(vma->vm_mm))) { - tlb_op(TLB_V3_PAGE, "c6, c0, 0", uaddr); tlb_op(TLB_V4_U_PAGE, "c8, c7, 1", uaddr); tlb_op(TLB_V4_D_PAGE, "c8, c6, 1", uaddr); tlb_op(TLB_V4_I_PAGE, "c8, c5, 1", uaddr); @@ -418,7 +412,6 @@ static inline void local_flush_tlb_kernel_page(unsigned long kaddr) if (tlb_flag(TLB_WB)) dsb(); - tlb_op(TLB_V3_PAGE, "c6, c0, 0", kaddr); tlb_op(TLB_V4_U_PAGE, "c8, c7, 1", kaddr); tlb_op(TLB_V4_D_PAGE, "c8, c6, 1", kaddr); tlb_op(TLB_V4_I_PAGE, "c8, c5, 1", kaddr); @@ -450,6 +443,21 @@ static inline void local_flush_bp_all(void) isb(); } +#ifdef CONFIG_ARM_ERRATA_798181 +static inline void dummy_flush_tlb_a15_erratum(void) +{ + /* + * Dummy TLBIMVAIS. Using the unmapped address 0 and ASID 0. + */ + asm("mcr p15, 0, %0, c8, c3, 1" : : "r" (0)); + dsb(); +} +#else +static inline void dummy_flush_tlb_a15_erratum(void) +{ +} +#endif + /* * flush_pmd_entry * diff --git a/arch/arm/include/asm/xen/events.h b/arch/arm/include/asm/xen/events.h index 5c27696de14f..8b1f37bfeeec 100644 --- a/arch/arm/include/asm/xen/events.h +++ b/arch/arm/include/asm/xen/events.h @@ -2,6 +2,7 @@ #define _ASM_ARM_XEN_EVENTS_H #include <asm/ptrace.h> +#include <asm/atomic.h> enum ipi_vector { XEN_PLACEHOLDER_VECTOR, @@ -15,26 +16,8 @@ static inline int xen_irqs_disabled(struct pt_regs *regs) return raw_irqs_disabled_flags(regs->ARM_cpsr); } -/* - * We cannot use xchg because it does not support 8-byte - * values. However it is safe to use {ldr,dtd}exd directly because all - * platforms which Xen can run on support those instructions. - */ -static inline xen_ulong_t xchg_xen_ulong(xen_ulong_t *ptr, xen_ulong_t val) -{ - xen_ulong_t oldval; - unsigned int tmp; - - wmb(); - asm volatile("@ xchg_xen_ulong\n" - "1: ldrexd %0, %H0, [%3]\n" - " strexd %1, %2, %H2, [%3]\n" - " teq %1, #0\n" - " bne 1b" - : "=&r" (oldval), "=&r" (tmp) - : "r" (val), "r" (ptr) - : "memory", "cc"); - return oldval; -} +#define xchg_xen_ulong(ptr, val) atomic64_xchg(container_of((ptr), \ + atomic64_t, \ + counter), (val)) #endif /* _ASM_ARM_XEN_EVENTS_H */ diff --git a/arch/arm/kernel/entry-common.S b/arch/arm/kernel/entry-common.S index 3248cde504ed..fefd7f971437 100644 --- a/arch/arm/kernel/entry-common.S +++ b/arch/arm/kernel/entry-common.S @@ -276,7 +276,13 @@ ENDPROC(ftrace_graph_caller_old) */ .macro mcount_enter +/* + * This pad compensates for the push {lr} at the call site. Note that we are + * unable to unwind through a function which does not otherwise save its lr. + */ + UNWIND(.pad #4) stmdb sp!, {r0-r3, lr} + UNWIND(.save {r0-r3, lr}) .endm .macro mcount_get_lr reg @@ -289,6 +295,7 @@ ENDPROC(ftrace_graph_caller_old) .endm ENTRY(__gnu_mcount_nc) +UNWIND(.fnstart) #ifdef CONFIG_DYNAMIC_FTRACE mov ip, lr ldmia sp!, {lr} @@ -296,17 +303,22 @@ ENTRY(__gnu_mcount_nc) #else __mcount #endif +UNWIND(.fnend) ENDPROC(__gnu_mcount_nc) #ifdef CONFIG_DYNAMIC_FTRACE ENTRY(ftrace_caller) +UNWIND(.fnstart) __ftrace_caller +UNWIND(.fnend) ENDPROC(ftrace_caller) #endif #ifdef CONFIG_FUNCTION_GRAPH_TRACER ENTRY(ftrace_graph_caller) +UNWIND(.fnstart) __ftrace_graph_caller +UNWIND(.fnend) ENDPROC(ftrace_graph_caller) #endif diff --git a/arch/arm/kernel/head.S b/arch/arm/kernel/head.S index e0eb9a1cae77..8bac553fe213 100644 --- a/arch/arm/kernel/head.S +++ b/arch/arm/kernel/head.S @@ -267,7 +267,7 @@ __create_page_tables: addne r6, r6, #1 << SECTION_SHIFT strne r6, [r3] -#if defined(CONFIG_LPAE) && defined(CONFIG_CPU_ENDIAN_BE8) +#if defined(CONFIG_ARM_LPAE) && defined(CONFIG_CPU_ENDIAN_BE8) sub r4, r4, #4 @ Fixup page table pointer @ for 64-bit descriptors #endif diff --git a/arch/arm/kernel/hw_breakpoint.c b/arch/arm/kernel/hw_breakpoint.c index 96093b75ab90..1fd749ee4a1b 100644 --- a/arch/arm/kernel/hw_breakpoint.c +++ b/arch/arm/kernel/hw_breakpoint.c @@ -966,7 +966,7 @@ static void reset_ctrl_regs(void *unused) } if (err) { - pr_warning("CPU %d debug is powered down!\n", cpu); + pr_warn_once("CPU %d debug is powered down!\n", cpu); cpumask_or(&debug_err_mask, &debug_err_mask, cpumask_of(cpu)); return; } @@ -987,7 +987,7 @@ clear_vcr: isb(); if (cpumask_intersects(&debug_err_mask, cpumask_of(cpu))) { - pr_warning("CPU %d failed to disable vector catch\n", cpu); + pr_warn_once("CPU %d failed to disable vector catch\n", cpu); return; } @@ -1007,7 +1007,7 @@ clear_vcr: } if (cpumask_intersects(&debug_err_mask, cpumask_of(cpu))) { - pr_warning("CPU %d failed to clear debug register pairs\n", cpu); + pr_warn_once("CPU %d failed to clear debug register pairs\n", cpu); return; } @@ -1043,7 +1043,7 @@ static int dbg_cpu_pm_notify(struct notifier_block *self, unsigned long action, return NOTIFY_OK; } -static struct notifier_block __cpuinitdata dbg_cpu_pm_nb = { +static struct notifier_block dbg_cpu_pm_nb = { .notifier_call = dbg_cpu_pm_notify, }; diff --git a/arch/arm/kernel/perf_event.c b/arch/arm/kernel/perf_event.c index 146157dfe27c..8c3094d0f7b7 100644 --- a/arch/arm/kernel/perf_event.c +++ b/arch/arm/kernel/perf_event.c @@ -253,7 +253,10 @@ validate_event(struct pmu_hw_events *hw_events, struct arm_pmu *armpmu = to_arm_pmu(event->pmu); struct pmu *leader_pmu = event->group_leader->pmu; - if (event->pmu != leader_pmu || event->state <= PERF_EVENT_STATE_OFF) + if (event->pmu != leader_pmu || event->state < PERF_EVENT_STATE_OFF) + return 1; + + if (event->state == PERF_EVENT_STATE_OFF && !event->attr.enable_on_exec) return 1; return armpmu->get_event_idx(hw_events, event) >= 0; diff --git a/arch/arm/kernel/sched_clock.c b/arch/arm/kernel/sched_clock.c index bd6f56b9ec21..59d2adb764a9 100644 --- a/arch/arm/kernel/sched_clock.c +++ b/arch/arm/kernel/sched_clock.c @@ -45,12 +45,12 @@ static u32 notrace jiffy_sched_clock_read(void) static u32 __read_mostly (*read_sched_clock)(void) = jiffy_sched_clock_read; -static inline u64 cyc_to_ns(u64 cyc, u32 mult, u32 shift) +static inline u64 notrace cyc_to_ns(u64 cyc, u32 mult, u32 shift) { return (cyc * mult) >> shift; } -static unsigned long long cyc_to_sched_clock(u32 cyc, u32 mask) +static unsigned long long notrace cyc_to_sched_clock(u32 cyc, u32 mask) { u64 epoch_ns; u32 epoch_cyc; diff --git a/arch/arm/kernel/setup.c b/arch/arm/kernel/setup.c index 3f6cbb2e3eda..234e339196c0 100644 --- a/arch/arm/kernel/setup.c +++ b/arch/arm/kernel/setup.c @@ -56,7 +56,6 @@ #include <asm/virt.h> #include "atags.h" -#include "tcm.h" #if defined(CONFIG_FPE_NWFPE) || defined(CONFIG_FPE_FASTFPE) @@ -353,6 +352,23 @@ void __init early_print(const char *str, ...) printk("%s", buf); } +static void __init cpuid_init_hwcaps(void) +{ + unsigned int divide_instrs; + + if (cpu_architecture() < CPU_ARCH_ARMv7) + return; + + divide_instrs = (read_cpuid_ext(CPUID_EXT_ISAR0) & 0x0f000000) >> 24; + + switch (divide_instrs) { + case 2: + elf_hwcap |= HWCAP_IDIVA; + case 1: + elf_hwcap |= HWCAP_IDIVT; + } +} + static void __init feat_v6_fixup(void) { int id = read_cpuid_id(); @@ -483,8 +499,11 @@ static void __init setup_processor(void) snprintf(elf_platform, ELF_PLATFORM_SIZE, "%s%c", list->elf_name, ENDIANNESS); elf_hwcap = list->elf_hwcap; + + cpuid_init_hwcaps(); + #ifndef CONFIG_ARM_THUMB - elf_hwcap &= ~HWCAP_THUMB; + elf_hwcap &= ~(HWCAP_THUMB | HWCAP_IDIVT); #endif feat_v6_fixup(); @@ -524,7 +543,7 @@ int __init arm_add_memory(phys_addr_t start, phys_addr_t size) size -= start & ~PAGE_MASK; bank->start = PAGE_ALIGN(start); -#ifndef CONFIG_LPAE +#ifndef CONFIG_ARM_LPAE if (bank->start + size < bank->start) { printk(KERN_CRIT "Truncating memory at 0x%08llx to fit in " "32-bit physical address space\n", (long long)start); @@ -778,8 +797,6 @@ void __init setup_arch(char **cmdline_p) reserve_crashkernel(); - tcm_init(); - #ifdef CONFIG_MULTI_IRQ_HANDLER handle_arch_irq = mdesc->handle_irq; #endif diff --git a/arch/arm/kernel/smp.c b/arch/arm/kernel/smp.c index 31644f1978d5..1f2ccccaf009 100644 --- a/arch/arm/kernel/smp.c +++ b/arch/arm/kernel/smp.c @@ -480,7 +480,7 @@ static void __cpuinit broadcast_timer_setup(struct clock_event_device *evt) evt->features = CLOCK_EVT_FEAT_ONESHOT | CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_DUMMY; - evt->rating = 400; + evt->rating = 100; evt->mult = 1; evt->set_mode = broadcast_timer_set_mode; @@ -673,9 +673,6 @@ static int cpufreq_callback(struct notifier_block *nb, if (freq->flags & CPUFREQ_CONST_LOOPS) return NOTIFY_OK; - if (arm_delay_ops.const_clock) - return NOTIFY_OK; - if (!per_cpu(l_p_j_ref, cpu)) { per_cpu(l_p_j_ref, cpu) = per_cpu(cpu_data, cpu).loops_per_jiffy; diff --git a/arch/arm/kernel/smp_tlb.c b/arch/arm/kernel/smp_tlb.c index bd0300531399..e82e1d248772 100644 --- a/arch/arm/kernel/smp_tlb.c +++ b/arch/arm/kernel/smp_tlb.c @@ -12,6 +12,7 @@ #include <asm/smp_plat.h> #include <asm/tlbflush.h> +#include <asm/mmu_context.h> /**********************************************************************/ @@ -69,12 +70,72 @@ static inline void ipi_flush_bp_all(void *ignored) local_flush_bp_all(); } +#ifdef CONFIG_ARM_ERRATA_798181 +static int erratum_a15_798181(void) +{ + unsigned int midr = read_cpuid_id(); + + /* Cortex-A15 r0p0..r3p2 affected */ + if ((midr & 0xff0ffff0) != 0x410fc0f0 || midr > 0x413fc0f2) + return 0; + return 1; +} +#else +static int erratum_a15_798181(void) +{ + return 0; +} +#endif + +static void ipi_flush_tlb_a15_erratum(void *arg) +{ + dmb(); +} + +static void broadcast_tlb_a15_erratum(void) +{ + if (!erratum_a15_798181()) + return; + + dummy_flush_tlb_a15_erratum(); + smp_call_function_many(cpu_online_mask, ipi_flush_tlb_a15_erratum, + NULL, 1); +} + +static void broadcast_tlb_mm_a15_erratum(struct mm_struct *mm) +{ + int cpu; + cpumask_t mask = { CPU_BITS_NONE }; + + if (!erratum_a15_798181()) + return; + + dummy_flush_tlb_a15_erratum(); + for_each_online_cpu(cpu) { + if (cpu == smp_processor_id()) + continue; + /* + * We only need to send an IPI if the other CPUs are running + * the same ASID as the one being invalidated. There is no + * need for locking around the active_asids check since the + * switch_mm() function has at least one dmb() (as required by + * this workaround) in case a context switch happens on + * another CPU after the condition below. + */ + if (atomic64_read(&mm->context.id) == + atomic64_read(&per_cpu(active_asids, cpu))) + cpumask_set_cpu(cpu, &mask); + } + smp_call_function_many(&mask, ipi_flush_tlb_a15_erratum, NULL, 1); +} + void flush_tlb_all(void) { if (tlb_ops_need_broadcast()) on_each_cpu(ipi_flush_tlb_all, NULL, 1); else local_flush_tlb_all(); + broadcast_tlb_a15_erratum(); } void flush_tlb_mm(struct mm_struct *mm) @@ -83,6 +144,7 @@ void flush_tlb_mm(struct mm_struct *mm) on_each_cpu_mask(mm_cpumask(mm), ipi_flush_tlb_mm, mm, 1); else local_flush_tlb_mm(mm); + broadcast_tlb_mm_a15_erratum(mm); } void flush_tlb_page(struct vm_area_struct *vma, unsigned long uaddr) @@ -95,6 +157,7 @@ void flush_tlb_page(struct vm_area_struct *vma, unsigned long uaddr) &ta, 1); } else local_flush_tlb_page(vma, uaddr); + broadcast_tlb_mm_a15_erratum(vma->vm_mm); } void flush_tlb_kernel_page(unsigned long kaddr) @@ -105,6 +168,7 @@ void flush_tlb_kernel_page(unsigned long kaddr) on_each_cpu(ipi_flush_tlb_kernel_page, &ta, 1); } else local_flush_tlb_kernel_page(kaddr); + broadcast_tlb_a15_erratum(); } void flush_tlb_range(struct vm_area_struct *vma, @@ -119,6 +183,7 @@ void flush_tlb_range(struct vm_area_struct *vma, &ta, 1); } else local_flush_tlb_range(vma, start, end); + broadcast_tlb_mm_a15_erratum(vma->vm_mm); } void flush_tlb_kernel_range(unsigned long start, unsigned long end) @@ -130,6 +195,7 @@ void flush_tlb_kernel_range(unsigned long start, unsigned long end) on_each_cpu(ipi_flush_tlb_kernel_range, &ta, 1); } else local_flush_tlb_kernel_range(start, end); + broadcast_tlb_a15_erratum(); } void flush_bp_all(void) diff --git a/arch/arm/kernel/tcm.c b/arch/arm/kernel/tcm.c index 30ae6bb4a310..f50f19e5c138 100644 --- a/arch/arm/kernel/tcm.c +++ b/arch/arm/kernel/tcm.c @@ -17,7 +17,6 @@ #include <asm/mach/map.h> #include <asm/memory.h> #include <asm/system_info.h> -#include "tcm.h" static struct gen_pool *tcm_pool; static bool dtcm_present; diff --git a/arch/arm/kvm/arm.c b/arch/arm/kvm/arm.c index 5a936988eb24..c1fe498983ac 100644 --- a/arch/arm/kvm/arm.c +++ b/arch/arm/kvm/arm.c @@ -201,6 +201,7 @@ int kvm_dev_ioctl_check_extension(long ext) break; case KVM_CAP_ARM_SET_DEVICE_ADDR: r = 1; + break; case KVM_CAP_NR_VCPUS: r = num_online_cpus(); break; diff --git a/arch/arm/kvm/coproc.c b/arch/arm/kvm/coproc.c index 4ea9a982269c..7bed7556077a 100644 --- a/arch/arm/kvm/coproc.c +++ b/arch/arm/kvm/coproc.c @@ -79,11 +79,11 @@ static bool access_dcsw(struct kvm_vcpu *vcpu, u32 val; int cpu; - cpu = get_cpu(); - if (!p->is_write) return read_from_write_only(vcpu, p); + cpu = get_cpu(); + cpumask_setall(&vcpu->arch.require_dcache_flush); cpumask_clear_cpu(cpu, &vcpu->arch.require_dcache_flush); diff --git a/arch/arm/kvm/vgic.c b/arch/arm/kvm/vgic.c index c9a17316e9fe..0e4cfe123b38 100644 --- a/arch/arm/kvm/vgic.c +++ b/arch/arm/kvm/vgic.c @@ -883,8 +883,7 @@ static bool vgic_queue_irq(struct kvm_vcpu *vcpu, u8 sgi_source_id, int irq) lr, irq, vgic_cpu->vgic_lr[lr]); BUG_ON(!test_bit(lr, vgic_cpu->lr_used)); vgic_cpu->vgic_lr[lr] |= GICH_LR_PENDING_BIT; - - goto out; + return true; } /* Try to use another LR for this interrupt */ @@ -898,7 +897,6 @@ static bool vgic_queue_irq(struct kvm_vcpu *vcpu, u8 sgi_source_id, int irq) vgic_cpu->vgic_irq_lr_map[irq] = lr; set_bit(lr, vgic_cpu->lr_used); -out: if (!vgic_irq_is_edge(vcpu, irq)) vgic_cpu->vgic_lr[lr] |= GICH_LR_EOI; @@ -1018,21 +1016,6 @@ static bool vgic_process_maintenance(struct kvm_vcpu *vcpu) kvm_debug("MISR = %08x\n", vgic_cpu->vgic_misr); - /* - * We do not need to take the distributor lock here, since the only - * action we perform is clearing the irq_active_bit for an EOIed - * level interrupt. There is a potential race with - * the queuing of an interrupt in __kvm_vgic_flush_hwstate(), where we - * check if the interrupt is already active. Two possibilities: - * - * - The queuing is occurring on the same vcpu: cannot happen, - * as we're already in the context of this vcpu, and - * executing the handler - * - The interrupt has been migrated to another vcpu, and we - * ignore this interrupt for this run. Big deal. It is still - * pending though, and will get considered when this vcpu - * exits. - */ if (vgic_cpu->vgic_misr & GICH_MISR_EOI) { /* * Some level interrupts have been EOIed. Clear their @@ -1054,6 +1037,13 @@ static bool vgic_process_maintenance(struct kvm_vcpu *vcpu) } else { vgic_cpu_irq_clear(vcpu, irq); } + + /* + * Despite being EOIed, the LR may not have + * been marked as empty. + */ + set_bit(lr, (unsigned long *)vgic_cpu->vgic_elrsr); + vgic_cpu->vgic_lr[lr] &= ~GICH_LR_ACTIVE_BIT; } } @@ -1064,9 +1054,8 @@ static bool vgic_process_maintenance(struct kvm_vcpu *vcpu) } /* - * Sync back the VGIC state after a guest run. We do not really touch - * the distributor here (the irq_pending_on_cpu bit is safe to set), - * so there is no need for taking its lock. + * Sync back the VGIC state after a guest run. The distributor lock is + * needed so we don't get preempted in the middle of the state processing. */ static void __kvm_vgic_sync_hwstate(struct kvm_vcpu *vcpu) { @@ -1112,10 +1101,14 @@ void kvm_vgic_flush_hwstate(struct kvm_vcpu *vcpu) void kvm_vgic_sync_hwstate(struct kvm_vcpu *vcpu) { + struct vgic_dist *dist = &vcpu->kvm->arch.vgic; + if (!irqchip_in_kernel(vcpu->kvm)) return; + spin_lock(&dist->lock); __kvm_vgic_sync_hwstate(vcpu); + spin_unlock(&dist->lock); } int kvm_vgic_vcpu_pending_irq(struct kvm_vcpu *vcpu) diff --git a/arch/arm/lib/delay.c b/arch/arm/lib/delay.c index 6b93f6a1a3c7..64dbfa57204a 100644 --- a/arch/arm/lib/delay.c +++ b/arch/arm/lib/delay.c @@ -58,7 +58,7 @@ static void __timer_delay(unsigned long cycles) static void __timer_const_udelay(unsigned long xloops) { unsigned long long loops = xloops; - loops *= loops_per_jiffy; + loops *= arm_delay_ops.ticks_per_jiffy; __timer_delay(loops >> UDELAY_SHIFT); } @@ -73,11 +73,13 @@ void __init register_current_timer_delay(const struct delay_timer *timer) pr_info("Switching to timer-based delay loop\n"); delay_timer = timer; lpj_fine = timer->freq / HZ; - loops_per_jiffy = lpj_fine; + + /* cpufreq may scale loops_per_jiffy, so keep a private copy */ + arm_delay_ops.ticks_per_jiffy = lpj_fine; arm_delay_ops.delay = __timer_delay; arm_delay_ops.const_udelay = __timer_const_udelay; arm_delay_ops.udelay = __timer_udelay; - arm_delay_ops.const_clock = true; + delay_calibrated = true; } else { pr_info("Ignoring duplicate/late registration of read_current_timer delay\n"); diff --git a/arch/arm/lib/memset.S b/arch/arm/lib/memset.S index d912e7397ecc..94b0650ea98f 100644 --- a/arch/arm/lib/memset.S +++ b/arch/arm/lib/memset.S @@ -14,31 +14,15 @@ .text .align 5 - .word 0 - -1: subs r2, r2, #4 @ 1 do we have enough - blt 5f @ 1 bytes to align with? - cmp r3, #2 @ 1 - strltb r1, [ip], #1 @ 1 - strleb r1, [ip], #1 @ 1 - strb r1, [ip], #1 @ 1 - add r2, r2, r3 @ 1 (r2 = r2 - (4 - r3)) -/* - * The pointer is now aligned and the length is adjusted. Try doing the - * memset again. - */ ENTRY(memset) -/* - * Preserve the contents of r0 for the return value. - */ - mov ip, r0 - ands r3, ip, #3 @ 1 unaligned? - bne 1b @ 1 + ands r3, r0, #3 @ 1 unaligned? + mov ip, r0 @ preserve r0 as return value + bne 6f @ 1 /* * we know that the pointer in ip is aligned to a word boundary. */ - orr r1, r1, r1, lsl #8 +1: orr r1, r1, r1, lsl #8 orr r1, r1, r1, lsl #16 mov r3, r1 cmp r2, #16 @@ -127,4 +111,13 @@ ENTRY(memset) tst r2, #1 strneb r1, [ip], #1 mov pc, lr + +6: subs r2, r2, #4 @ 1 do we have enough + blt 5b @ 1 bytes to align with? + cmp r3, #2 @ 1 + strltb r1, [ip], #1 @ 1 + strleb r1, [ip], #1 @ 1 + strb r1, [ip], #1 @ 1 + add r2, r2, r3 @ 1 (r2 = r2 - (4 - r3)) + b 1b ENDPROC(memset) diff --git a/arch/arm/mach-at91/board-foxg20.c b/arch/arm/mach-at91/board-foxg20.c index 2ea7059b840b..c20a870ea9c9 100644 --- a/arch/arm/mach-at91/board-foxg20.c +++ b/arch/arm/mach-at91/board-foxg20.c @@ -176,6 +176,7 @@ static struct w1_gpio_platform_data w1_gpio_pdata = { /* If you choose to use a pin other than PB16 it needs to be 3.3V */ .pin = AT91_PIN_PB16, .is_open_drain = 1, + .ext_pullup_enable_pin = -EINVAL, }; static struct platform_device w1_device = { diff --git a/arch/arm/mach-at91/board-stamp9g20.c b/arch/arm/mach-at91/board-stamp9g20.c index a033b8df9fb2..869cbecf00b7 100644 --- a/arch/arm/mach-at91/board-stamp9g20.c +++ b/arch/arm/mach-at91/board-stamp9g20.c @@ -188,6 +188,7 @@ static struct spi_board_info portuxg20_spi_devices[] = { static struct w1_gpio_platform_data w1_gpio_pdata = { .pin = AT91_PIN_PA29, .is_open_drain = 1, + .ext_pullup_enable_pin = -EINVAL, }; static struct platform_device w1_device = { diff --git a/arch/arm/mach-at91/include/mach/gpio.h b/arch/arm/mach-at91/include/mach/gpio.h index eed465ab0dd7..5fc23771c154 100644 --- a/arch/arm/mach-at91/include/mach/gpio.h +++ b/arch/arm/mach-at91/include/mach/gpio.h @@ -209,6 +209,14 @@ extern int at91_get_gpio_value(unsigned pin); extern void at91_gpio_suspend(void); extern void at91_gpio_resume(void); +#ifdef CONFIG_PINCTRL_AT91 +extern void at91_pinctrl_gpio_suspend(void); +extern void at91_pinctrl_gpio_resume(void); +#else +static inline void at91_pinctrl_gpio_suspend(void) {} +static inline void at91_pinctrl_gpio_resume(void) {} +#endif + #endif /* __ASSEMBLY__ */ #endif diff --git a/arch/arm/mach-at91/irq.c b/arch/arm/mach-at91/irq.c index 8e210262aeee..e0ca59171022 100644 --- a/arch/arm/mach-at91/irq.c +++ b/arch/arm/mach-at91/irq.c @@ -92,23 +92,21 @@ static int at91_aic_set_wake(struct irq_data *d, unsigned value) void at91_irq_suspend(void) { - int i = 0, bit; + int bit = -1; if (has_aic5()) { /* disable enabled irqs */ - while ((bit = find_next_bit(backups, n_irqs, i)) < n_irqs) { + while ((bit = find_next_bit(backups, n_irqs, bit + 1)) < n_irqs) { at91_aic_write(AT91_AIC5_SSR, bit & AT91_AIC5_INTSEL_MSK); at91_aic_write(AT91_AIC5_IDCR, 1); - i = bit; } /* enable wakeup irqs */ - i = 0; - while ((bit = find_next_bit(wakeups, n_irqs, i)) < n_irqs) { + bit = -1; + while ((bit = find_next_bit(wakeups, n_irqs, bit + 1)) < n_irqs) { at91_aic_write(AT91_AIC5_SSR, bit & AT91_AIC5_INTSEL_MSK); at91_aic_write(AT91_AIC5_IECR, 1); - i = bit; } } else { at91_aic_write(AT91_AIC_IDCR, *backups); @@ -118,23 +116,21 @@ void at91_irq_suspend(void) void at91_irq_resume(void) { - int i = 0, bit; + int bit = -1; if (has_aic5()) { /* disable wakeup irqs */ - while ((bit = find_next_bit(wakeups, n_irqs, i)) < n_irqs) { + while ((bit = find_next_bit(wakeups, n_irqs, bit + 1)) < n_irqs) { at91_aic_write(AT91_AIC5_SSR, bit & AT91_AIC5_INTSEL_MSK); at91_aic_write(AT91_AIC5_IDCR, 1); - i = bit; } /* enable irqs disabled for suspend */ - i = 0; - while ((bit = find_next_bit(backups, n_irqs, i)) < n_irqs) { + bit = -1; + while ((bit = find_next_bit(backups, n_irqs, bit + 1)) < n_irqs) { at91_aic_write(AT91_AIC5_SSR, bit & AT91_AIC5_INTSEL_MSK); at91_aic_write(AT91_AIC5_IECR, 1); - i = bit; } } else { at91_aic_write(AT91_AIC_IDCR, *wakeups); diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c index adb6db888a1f..73f1f250403a 100644 --- a/arch/arm/mach-at91/pm.c +++ b/arch/arm/mach-at91/pm.c @@ -201,7 +201,10 @@ extern u32 at91_slow_clock_sz; static int at91_pm_enter(suspend_state_t state) { - at91_gpio_suspend(); + if (of_have_populated_dt()) + at91_pinctrl_gpio_suspend(); + else + at91_gpio_suspend(); at91_irq_suspend(); pr_debug("AT91: PM - wake mask %08x, pm state %d\n", @@ -286,7 +289,10 @@ static int at91_pm_enter(suspend_state_t state) error: target_state = PM_SUSPEND_ON; at91_irq_resume(); - at91_gpio_resume(); + if (of_have_populated_dt()) + at91_pinctrl_gpio_resume(); + else + at91_gpio_resume(); return 0; } diff --git a/arch/arm/mach-cns3xxx/core.c b/arch/arm/mach-cns3xxx/core.c index e698f26cc0cb..52e4bb5cf12d 100644 --- a/arch/arm/mach-cns3xxx/core.c +++ b/arch/arm/mach-cns3xxx/core.c @@ -22,19 +22,9 @@ static struct map_desc cns3xxx_io_desc[] __initdata = { { - .virtual = CNS3XXX_TC11MP_TWD_BASE_VIRT, - .pfn = __phys_to_pfn(CNS3XXX_TC11MP_TWD_BASE), - .length = SZ_4K, - .type = MT_DEVICE, - }, { - .virtual = CNS3XXX_TC11MP_GIC_CPU_BASE_VIRT, - .pfn = __phys_to_pfn(CNS3XXX_TC11MP_GIC_CPU_BASE), - .length = SZ_4K, - .type = MT_DEVICE, - }, { - .virtual = CNS3XXX_TC11MP_GIC_DIST_BASE_VIRT, - .pfn = __phys_to_pfn(CNS3XXX_TC11MP_GIC_DIST_BASE), - .length = SZ_4K, + .virtual = CNS3XXX_TC11MP_SCU_BASE_VIRT, + .pfn = __phys_to_pfn(CNS3XXX_TC11MP_SCU_BASE), + .length = SZ_8K, .type = MT_DEVICE, }, { .virtual = CNS3XXX_TIMER1_2_3_BASE_VIRT, diff --git a/arch/arm/mach-cns3xxx/include/mach/cns3xxx.h b/arch/arm/mach-cns3xxx/include/mach/cns3xxx.h index 191c8e57f289..b1021aafa481 100644 --- a/arch/arm/mach-cns3xxx/include/mach/cns3xxx.h +++ b/arch/arm/mach-cns3xxx/include/mach/cns3xxx.h @@ -94,10 +94,10 @@ #define RTC_INTR_STS_OFFSET 0x34 #define CNS3XXX_MISC_BASE 0x76000000 /* Misc Control */ -#define CNS3XXX_MISC_BASE_VIRT 0xFFF07000 /* Misc Control */ +#define CNS3XXX_MISC_BASE_VIRT 0xFB000000 /* Misc Control */ #define CNS3XXX_PM_BASE 0x77000000 /* Power Management Control */ -#define CNS3XXX_PM_BASE_VIRT 0xFFF08000 +#define CNS3XXX_PM_BASE_VIRT 0xFB001000 #define PM_CLK_GATE_OFFSET 0x00 #define PM_SOFT_RST_OFFSET 0x04 @@ -109,7 +109,7 @@ #define PM_PLL_HM_PD_OFFSET 0x1C #define CNS3XXX_UART0_BASE 0x78000000 /* UART 0 */ -#define CNS3XXX_UART0_BASE_VIRT 0xFFF09000 +#define CNS3XXX_UART0_BASE_VIRT 0xFB002000 #define CNS3XXX_UART1_BASE 0x78400000 /* UART 1 */ #define CNS3XXX_UART1_BASE_VIRT 0xFFF0A000 @@ -130,7 +130,7 @@ #define CNS3XXX_I2S_BASE_VIRT 0xFFF10000 #define CNS3XXX_TIMER1_2_3_BASE 0x7C800000 /* Timer */ -#define CNS3XXX_TIMER1_2_3_BASE_VIRT 0xFFF10800 +#define CNS3XXX_TIMER1_2_3_BASE_VIRT 0xFB003000 #define TIMER1_COUNTER_OFFSET 0x00 #define TIMER1_AUTO_RELOAD_OFFSET 0x04 @@ -227,16 +227,16 @@ * Testchip peripheral and fpga gic regions */ #define CNS3XXX_TC11MP_SCU_BASE 0x90000000 /* IRQ, Test chip */ -#define CNS3XXX_TC11MP_SCU_BASE_VIRT 0xFF000000 +#define CNS3XXX_TC11MP_SCU_BASE_VIRT 0xFB004000 #define CNS3XXX_TC11MP_GIC_CPU_BASE 0x90000100 /* Test chip interrupt controller CPU interface */ -#define CNS3XXX_TC11MP_GIC_CPU_BASE_VIRT 0xFF000100 +#define CNS3XXX_TC11MP_GIC_CPU_BASE_VIRT (CNS3XXX_TC11MP_SCU_BASE_VIRT + 0x100) #define CNS3XXX_TC11MP_TWD_BASE 0x90000600 -#define CNS3XXX_TC11MP_TWD_BASE_VIRT 0xFF000600 +#define CNS3XXX_TC11MP_TWD_BASE_VIRT (CNS3XXX_TC11MP_SCU_BASE_VIRT + 0x600) #define CNS3XXX_TC11MP_GIC_DIST_BASE 0x90001000 /* Test chip interrupt controller distributor */ -#define CNS3XXX_TC11MP_GIC_DIST_BASE_VIRT 0xFF001000 +#define CNS3XXX_TC11MP_GIC_DIST_BASE_VIRT (CNS3XXX_TC11MP_SCU_BASE_VIRT + 0x1000) #define CNS3XXX_TC11MP_L220_BASE 0x92002000 /* L220 registers */ #define CNS3XXX_TC11MP_L220_BASE_VIRT 0xFF002000 diff --git a/arch/arm/mach-davinci/dma.c b/arch/arm/mach-davinci/dma.c index a685e9706b7b..45b7c71d9cc1 100644 --- a/arch/arm/mach-davinci/dma.c +++ b/arch/arm/mach-davinci/dma.c @@ -743,6 +743,9 @@ EXPORT_SYMBOL(edma_free_channel); */ int edma_alloc_slot(unsigned ctlr, int slot) { + if (!edma_cc[ctlr]) + return -EINVAL; + if (slot >= 0) slot = EDMA_CHAN_SLOT(slot); diff --git a/arch/arm/mach-ep93xx/include/mach/uncompress.h b/arch/arm/mach-ep93xx/include/mach/uncompress.h index d2afb4dd82ab..b5cc77d2380b 100644 --- a/arch/arm/mach-ep93xx/include/mach/uncompress.h +++ b/arch/arm/mach-ep93xx/include/mach/uncompress.h @@ -47,9 +47,13 @@ static void __raw_writel(unsigned int value, unsigned int ptr) static inline void putc(int c) { - /* Transmit fifo not full? */ - while (__raw_readb(PHYS_UART_FLAG) & UART_FLAG_TXFF) - ; + int i; + + for (i = 0; i < 10000; i++) { + /* Transmit fifo not full? */ + if (!(__raw_readb(PHYS_UART_FLAG) & UART_FLAG_TXFF)) + break; + } __raw_writeb(c, PHYS_UART_DATA); } diff --git a/arch/arm/mach-footbridge/Kconfig b/arch/arm/mach-footbridge/Kconfig index abda5a18a664..0f2111a11315 100644 --- a/arch/arm/mach-footbridge/Kconfig +++ b/arch/arm/mach-footbridge/Kconfig @@ -67,6 +67,7 @@ config ARCH_NETWINDER select ISA select ISA_DMA select PCI + select VIRT_TO_BUS help Say Y here if you intend to run this kernel on the Rebel.COM NetWinder. Information about this machine can be found at: diff --git a/arch/arm/mach-highbank/hotplug.c b/arch/arm/mach-highbank/hotplug.c index f30c52843396..890cae23c12a 100644 --- a/arch/arm/mach-highbank/hotplug.c +++ b/arch/arm/mach-highbank/hotplug.c @@ -28,13 +28,11 @@ extern void secondary_startup(void); */ void __ref highbank_cpu_die(unsigned int cpu) { - flush_cache_all(); - highbank_set_cpu_jump(cpu, phys_to_virt(0)); - highbank_set_core_pwr(); - cpu_do_idle(); + flush_cache_louis(); + highbank_set_core_pwr(); - /* We should never return from idle */ - panic("highbank: cpu %d unexpectedly exit from shutdown\n", cpu); + while (1) + cpu_do_idle(); } diff --git a/arch/arm/mach-imx/clk-imx35.c b/arch/arm/mach-imx/clk-imx35.c index 74e3a34d78b8..2193c834f55c 100644 --- a/arch/arm/mach-imx/clk-imx35.c +++ b/arch/arm/mach-imx/clk-imx35.c @@ -257,6 +257,7 @@ int __init mx35_clocks_init(void) clk_register_clkdev(clk[wdog_gate], NULL, "imx2-wdt.0"); clk_register_clkdev(clk[nfc_div], NULL, "imx25-nand.0"); clk_register_clkdev(clk[csi_gate], NULL, "mx3-camera.0"); + clk_register_clkdev(clk[admux_gate], "audmux", NULL); clk_prepare_enable(clk[spba_gate]); clk_prepare_enable(clk[gpio1_gate]); @@ -264,6 +265,8 @@ int __init mx35_clocks_init(void) clk_prepare_enable(clk[gpio3_gate]); clk_prepare_enable(clk[iim_gate]); clk_prepare_enable(clk[emi_gate]); + clk_prepare_enable(clk[max_gate]); + clk_prepare_enable(clk[iomuxc_gate]); /* * SCC is needed to boot via mmc after a watchdog reset. The clock code diff --git a/arch/arm/mach-imx/clk-imx6q.c b/arch/arm/mach-imx/clk-imx6q.c index 7b025ee528a5..d38e54f5b6d7 100644 --- a/arch/arm/mach-imx/clk-imx6q.c +++ b/arch/arm/mach-imx/clk-imx6q.c @@ -115,7 +115,7 @@ static const char *gpu2d_core_sels[] = { "axi", "pll3_usb_otg", "pll2_pfd0_352m" static const char *gpu3d_core_sels[] = { "mmdc_ch0_axi", "pll3_usb_otg", "pll2_pfd1_594m", "pll2_pfd2_396m", }; static const char *gpu3d_shader_sels[] = { "mmdc_ch0_axi", "pll3_usb_otg", "pll2_pfd1_594m", "pll2_pfd9_720m", }; static const char *ipu_sels[] = { "mmdc_ch0_axi", "pll2_pfd2_396m", "pll3_120m", "pll3_pfd1_540m", }; -static const char *ldb_di_sels[] = { "pll5_video", "pll2_pfd0_352m", "pll2_pfd2_396m", "mmdc_ch1_axi", "pll3_pfd1_540m", }; +static const char *ldb_di_sels[] = { "pll5_video", "pll2_pfd0_352m", "pll2_pfd2_396m", "mmdc_ch1_axi", "pll3_usb_otg", }; static const char *ipu_di_pre_sels[] = { "mmdc_ch0_axi", "pll3_usb_otg", "pll5_video", "pll2_pfd0_352m", "pll2_pfd2_396m", "pll3_pfd1_540m", }; static const char *ipu1_di0_sels[] = { "ipu1_di0_pre", "dummy", "dummy", "ldb_di0", "ldb_di1", }; static const char *ipu1_di1_sels[] = { "ipu1_di1_pre", "dummy", "dummy", "ldb_di0", "ldb_di1", }; @@ -172,7 +172,7 @@ static struct clk *clk[clk_max]; static struct clk_onecell_data clk_data; static enum mx6q_clks const clks_init_on[] __initconst = { - mmdc_ch0_axi, rom, + mmdc_ch0_axi, rom, pll1_sys, }; static struct clk_div_table clk_enet_ref_table[] = { @@ -443,7 +443,6 @@ int __init mx6q_clocks_init(void) clk_register_clkdev(clk[gpt_ipg], "ipg", "imx-gpt.0"); clk_register_clkdev(clk[gpt_ipg_per], "per", "imx-gpt.0"); - clk_register_clkdev(clk[twd], NULL, "smp_twd"); clk_register_clkdev(clk[cko1_sel], "cko1_sel", NULL); clk_register_clkdev(clk[ahb], "ahb", NULL); clk_register_clkdev(clk[cko1], "cko1", NULL); diff --git a/arch/arm/mach-imx/common.h b/arch/arm/mach-imx/common.h index 5a800bfcec5b..5bf4a97ab241 100644 --- a/arch/arm/mach-imx/common.h +++ b/arch/arm/mach-imx/common.h @@ -110,6 +110,8 @@ void tzic_handle_irq(struct pt_regs *); extern void imx_enable_cpu(int cpu, bool enable); extern void imx_set_cpu_jump(int cpu, void *jump_addr); +extern u32 imx_get_cpu_arg(int cpu); +extern void imx_set_cpu_arg(int cpu, u32 arg); extern void v7_cpu_resume(void); extern u32 *pl310_get_save_ptr(void); #ifdef CONFIG_SMP diff --git a/arch/arm/mach-imx/headsmp.S b/arch/arm/mach-imx/headsmp.S index 921fc1555854..a58c8b0527cc 100644 --- a/arch/arm/mach-imx/headsmp.S +++ b/arch/arm/mach-imx/headsmp.S @@ -26,16 +26,16 @@ ENDPROC(v7_secondary_startup) #ifdef CONFIG_PM /* - * The following code is located into the .data section. This is to - * allow phys_l2x0_saved_regs to be accessed with a relative load - * as we are running on physical address here. + * The following code must assume it is running from physical address + * where absolute virtual addresses to the data section have to be + * turned into relative ones. */ - .data - .align #ifdef CONFIG_CACHE_L2X0 .macro pl310_resume - ldr r2, phys_l2x0_saved_regs + adr r0, l2x0_saved_regs_offset + ldr r2, [r0] + add r2, r2, r0 ldr r0, [r2, #L2X0_R_PHY_BASE] @ get physical base of l2x0 ldr r1, [r2, #L2X0_R_AUX_CTRL] @ get aux_ctrl value str r1, [r0, #L2X0_AUX_CTRL] @ restore aux_ctrl @@ -43,9 +43,9 @@ ENDPROC(v7_secondary_startup) str r1, [r0, #L2X0_CTRL] @ re-enable L2 .endm - .globl phys_l2x0_saved_regs -phys_l2x0_saved_regs: - .long 0 +l2x0_saved_regs_offset: + .word l2x0_saved_regs - . + #else .macro pl310_resume .endm diff --git a/arch/arm/mach-imx/hotplug.c b/arch/arm/mach-imx/hotplug.c index 7bc5fe15dda2..361a253e2b63 100644 --- a/arch/arm/mach-imx/hotplug.c +++ b/arch/arm/mach-imx/hotplug.c @@ -46,11 +46,23 @@ static inline void cpu_enter_lowpower(void) void imx_cpu_die(unsigned int cpu) { cpu_enter_lowpower(); + /* + * We use the cpu jumping argument register to sync with + * imx_cpu_kill() which is running on cpu0 and waiting for + * the register being cleared to kill the cpu. + */ + imx_set_cpu_arg(cpu, ~0); cpu_do_idle(); } int imx_cpu_kill(unsigned int cpu) { + unsigned long timeout = jiffies + msecs_to_jiffies(50); + + while (imx_get_cpu_arg(cpu) == 0) + if (time_after(jiffies, timeout)) + return 0; imx_enable_cpu(cpu, false); + imx_set_cpu_arg(cpu, 0); return 1; } diff --git a/arch/arm/mach-imx/imx25-dt.c b/arch/arm/mach-imx/imx25-dt.c index 03b65e5ea541..82348391582a 100644 --- a/arch/arm/mach-imx/imx25-dt.c +++ b/arch/arm/mach-imx/imx25-dt.c @@ -27,6 +27,11 @@ static const char * const imx25_dt_board_compat[] __initconst = { NULL }; +static void __init imx25_timer_init(void) +{ + mx25_clocks_init_dt(); +} + DT_MACHINE_START(IMX25_DT, "Freescale i.MX25 (Device Tree Support)") .map_io = mx25_map_io, .init_early = imx25_init_early, diff --git a/arch/arm/mach-imx/pm-imx6q.c b/arch/arm/mach-imx/pm-imx6q.c index ee42d20cba19..5faba7a3c95f 100644 --- a/arch/arm/mach-imx/pm-imx6q.c +++ b/arch/arm/mach-imx/pm-imx6q.c @@ -22,8 +22,6 @@ #include "common.h" #include "hardware.h" -extern unsigned long phys_l2x0_saved_regs; - static int imx6q_suspend_finish(unsigned long val) { cpu_do_idle(); @@ -57,18 +55,5 @@ static const struct platform_suspend_ops imx6q_pm_ops = { void __init imx6q_pm_init(void) { - /* - * The l2x0 core code provides an infrastucture to save and restore - * l2x0 registers across suspend/resume cycle. But because imx6q - * retains L2 content during suspend and needs to resume L2 before - * MMU is enabled, it can only utilize register saving support and - * have to take care of restoring on its own. So we save physical - * address of the data structure used by l2x0 core to save registers, - * and later restore the necessary ones in imx6q resume entry. - */ -#ifdef CONFIG_CACHE_L2X0 - phys_l2x0_saved_regs = __pa(&l2x0_saved_regs); -#endif - suspend_set_ops(&imx6q_pm_ops); } diff --git a/arch/arm/mach-imx/src.c b/arch/arm/mach-imx/src.c index e15f1555c59b..09a742f8c7ab 100644 --- a/arch/arm/mach-imx/src.c +++ b/arch/arm/mach-imx/src.c @@ -43,6 +43,18 @@ void imx_set_cpu_jump(int cpu, void *jump_addr) src_base + SRC_GPR1 + cpu * 8); } +u32 imx_get_cpu_arg(int cpu) +{ + cpu = cpu_logical_map(cpu); + return readl_relaxed(src_base + SRC_GPR1 + cpu * 8 + 4); +} + +void imx_set_cpu_arg(int cpu, u32 arg) +{ + cpu = cpu_logical_map(cpu); + writel_relaxed(arg, src_base + SRC_GPR1 + cpu * 8 + 4); +} + void imx_src_prepare_restart(void) { u32 val; diff --git a/arch/arm/mach-ixp4xx/vulcan-setup.c b/arch/arm/mach-ixp4xx/vulcan-setup.c index d42730a1d4ab..d599e354ca57 100644 --- a/arch/arm/mach-ixp4xx/vulcan-setup.c +++ b/arch/arm/mach-ixp4xx/vulcan-setup.c @@ -163,6 +163,7 @@ static struct platform_device vulcan_max6369 = { static struct w1_gpio_platform_data vulcan_w1_gpio_pdata = { .pin = 14, + .ext_pullup_enable_pin = -EINVAL, }; static struct platform_device vulcan_w1_gpio = { diff --git a/arch/arm/mach-kirkwood/board-dt.c b/arch/arm/mach-kirkwood/board-dt.c index 2e73e9d53f70..d367aa6b47bb 100644 --- a/arch/arm/mach-kirkwood/board-dt.c +++ b/arch/arm/mach-kirkwood/board-dt.c @@ -41,16 +41,12 @@ static void __init kirkwood_legacy_clk_init(void) struct device_node *np = of_find_compatible_node( NULL, NULL, "marvell,kirkwood-gating-clock"); - struct of_phandle_args clkspec; + struct clk *clk; clkspec.np = np; clkspec.args_count = 1; - clkspec.args[0] = CGC_BIT_GE0; - orion_clkdev_add(NULL, "mv643xx_eth_port.0", - of_clk_get_from_provider(&clkspec)); - clkspec.args[0] = CGC_BIT_PEX0; orion_clkdev_add("0", "pcie", of_clk_get_from_provider(&clkspec)); @@ -59,9 +55,24 @@ static void __init kirkwood_legacy_clk_init(void) orion_clkdev_add("1", "pcie", of_clk_get_from_provider(&clkspec)); - clkspec.args[0] = CGC_BIT_GE1; - orion_clkdev_add(NULL, "mv643xx_eth_port.1", + clkspec.args[0] = CGC_BIT_SDIO; + orion_clkdev_add(NULL, "mvsdio", of_clk_get_from_provider(&clkspec)); + + /* + * The ethernet interfaces forget the MAC address assigned by + * u-boot if the clocks are turned off. Until proper DT support + * is available we always enable them for now. + */ + clkspec.args[0] = CGC_BIT_GE0; + clk = of_clk_get_from_provider(&clkspec); + orion_clkdev_add(NULL, "mv643xx_eth_port.0", clk); + clk_prepare_enable(clk); + + clkspec.args[0] = CGC_BIT_GE1; + clk = of_clk_get_from_provider(&clkspec); + orion_clkdev_add(NULL, "mv643xx_eth_port.1", clk); + clk_prepare_enable(clk); } static void __init kirkwood_of_clk_init(void) diff --git a/arch/arm/mach-kirkwood/board-iomega_ix2_200.c b/arch/arm/mach-kirkwood/board-iomega_ix2_200.c index f655b2637b0e..e5f70415905a 100644 --- a/arch/arm/mach-kirkwood/board-iomega_ix2_200.c +++ b/arch/arm/mach-kirkwood/board-iomega_ix2_200.c @@ -20,10 +20,15 @@ static struct mv643xx_eth_platform_data iomega_ix2_200_ge00_data = { .duplex = DUPLEX_FULL, }; +static struct mv643xx_eth_platform_data iomega_ix2_200_ge01_data = { + .phy_addr = MV643XX_ETH_PHY_ADDR(11), +}; + void __init iomega_ix2_200_init(void) { /* * Basic setup. Needs to be called early. */ - kirkwood_ge01_init(&iomega_ix2_200_ge00_data); + kirkwood_ge00_init(&iomega_ix2_200_ge00_data); + kirkwood_ge01_init(&iomega_ix2_200_ge01_data); } diff --git a/arch/arm/mach-kirkwood/guruplug-setup.c b/arch/arm/mach-kirkwood/guruplug-setup.c index 1c6e736cbbf8..08dd739aa709 100644 --- a/arch/arm/mach-kirkwood/guruplug-setup.c +++ b/arch/arm/mach-kirkwood/guruplug-setup.c @@ -53,6 +53,8 @@ static struct mv_sata_platform_data guruplug_sata_data = { static struct mvsdio_platform_data guruplug_mvsdio_data = { /* unfortunately the CD signal has not been connected */ + .gpio_card_detect = -1, + .gpio_write_protect = -1, }; static struct gpio_led guruplug_led_pins[] = { diff --git a/arch/arm/mach-kirkwood/openrd-setup.c b/arch/arm/mach-kirkwood/openrd-setup.c index 8ddd69fdc937..6a6eb548307d 100644 --- a/arch/arm/mach-kirkwood/openrd-setup.c +++ b/arch/arm/mach-kirkwood/openrd-setup.c @@ -55,6 +55,7 @@ static struct mv_sata_platform_data openrd_sata_data = { static struct mvsdio_platform_data openrd_mvsdio_data = { .gpio_card_detect = 29, /* MPP29 used as SD card detect */ + .gpio_write_protect = -1, }; static unsigned int openrd_mpp_config[] __initdata = { diff --git a/arch/arm/mach-kirkwood/rd88f6281-setup.c b/arch/arm/mach-kirkwood/rd88f6281-setup.c index c7d93b48926b..d24223166e06 100644 --- a/arch/arm/mach-kirkwood/rd88f6281-setup.c +++ b/arch/arm/mach-kirkwood/rd88f6281-setup.c @@ -69,6 +69,7 @@ static struct mv_sata_platform_data rd88f6281_sata_data = { static struct mvsdio_platform_data rd88f6281_mvsdio_data = { .gpio_card_detect = 28, + .gpio_write_protect = -1, }; static unsigned int rd88f6281_mpp_config[] __initdata = { diff --git a/arch/arm/mach-mmp/gplugd.c b/arch/arm/mach-mmp/gplugd.c index d1e2d595e79c..f62b68d926f4 100644 --- a/arch/arm/mach-mmp/gplugd.c +++ b/arch/arm/mach-mmp/gplugd.c @@ -9,6 +9,7 @@ */ #include <linux/init.h> +#include <linux/platform_device.h> #include <linux/gpio.h> #include <asm/mach/arch.h> diff --git a/arch/arm/mach-msm/timer.c b/arch/arm/mach-msm/timer.c index 2969027f02fa..f9fd77e8f1f5 100644 --- a/arch/arm/mach-msm/timer.c +++ b/arch/arm/mach-msm/timer.c @@ -62,7 +62,10 @@ static int msm_timer_set_next_event(unsigned long cycles, { u32 ctrl = readl_relaxed(event_base + TIMER_ENABLE); - writel_relaxed(0, event_base + TIMER_CLEAR); + ctrl &= ~TIMER_ENABLE_EN; + writel_relaxed(ctrl, event_base + TIMER_ENABLE); + + writel_relaxed(ctrl, event_base + TIMER_CLEAR); writel_relaxed(cycles, event_base + TIMER_MATCH_VAL); writel_relaxed(ctrl | TIMER_ENABLE_EN, event_base + TIMER_ENABLE); return 0; diff --git a/arch/arm/mach-mvebu/irq-armada-370-xp.c b/arch/arm/mach-mvebu/irq-armada-370-xp.c index 274ff58271de..d5970f5a1e8d 100644 --- a/arch/arm/mach-mvebu/irq-armada-370-xp.c +++ b/arch/arm/mach-mvebu/irq-armada-370-xp.c @@ -44,6 +44,8 @@ #define ARMADA_370_XP_MAX_PER_CPU_IRQS (28) +#define ARMADA_370_XP_TIMER0_PER_CPU_IRQ (5) + #define ACTIVE_DOORBELLS (8) static DEFINE_RAW_SPINLOCK(irq_controller_lock); @@ -59,36 +61,26 @@ static struct irq_domain *armada_370_xp_mpic_domain; */ static void armada_370_xp_irq_mask(struct irq_data *d) { -#ifdef CONFIG_SMP irq_hw_number_t hwirq = irqd_to_hwirq(d); - if (hwirq > ARMADA_370_XP_MAX_PER_CPU_IRQS) + if (hwirq != ARMADA_370_XP_TIMER0_PER_CPU_IRQ) writel(hwirq, main_int_base + ARMADA_370_XP_INT_CLEAR_ENABLE_OFFS); else writel(hwirq, per_cpu_int_base + ARMADA_370_XP_INT_SET_MASK_OFFS); -#else - writel(irqd_to_hwirq(d), - per_cpu_int_base + ARMADA_370_XP_INT_SET_MASK_OFFS); -#endif } static void armada_370_xp_irq_unmask(struct irq_data *d) { -#ifdef CONFIG_SMP irq_hw_number_t hwirq = irqd_to_hwirq(d); - if (hwirq > ARMADA_370_XP_MAX_PER_CPU_IRQS) + if (hwirq != ARMADA_370_XP_TIMER0_PER_CPU_IRQ) writel(hwirq, main_int_base + ARMADA_370_XP_INT_SET_ENABLE_OFFS); else writel(hwirq, per_cpu_int_base + ARMADA_370_XP_INT_CLEAR_MASK_OFFS); -#else - writel(irqd_to_hwirq(d), - per_cpu_int_base + ARMADA_370_XP_INT_CLEAR_MASK_OFFS); -#endif } #ifdef CONFIG_SMP @@ -144,10 +136,14 @@ static int armada_370_xp_mpic_irq_map(struct irq_domain *h, unsigned int virq, irq_hw_number_t hw) { armada_370_xp_irq_mask(irq_get_irq_data(virq)); - writel(hw, main_int_base + ARMADA_370_XP_INT_SET_ENABLE_OFFS); + if (hw != ARMADA_370_XP_TIMER0_PER_CPU_IRQ) + writel(hw, per_cpu_int_base + + ARMADA_370_XP_INT_CLEAR_MASK_OFFS); + else + writel(hw, main_int_base + ARMADA_370_XP_INT_SET_ENABLE_OFFS); irq_set_status_flags(virq, IRQ_LEVEL); - if (hw < ARMADA_370_XP_MAX_PER_CPU_IRQS) { + if (hw == ARMADA_370_XP_TIMER0_PER_CPU_IRQ) { irq_set_percpu_devid(virq); irq_set_chip_and_handler(virq, &armada_370_xp_irq_chip, handle_percpu_devid_irq); diff --git a/arch/arm/mach-mxs/icoll.c b/arch/arm/mach-mxs/icoll.c index 8fb23af154b3..e26eeba46598 100644 --- a/arch/arm/mach-mxs/icoll.c +++ b/arch/arm/mach-mxs/icoll.c @@ -100,7 +100,7 @@ static struct irq_domain_ops icoll_irq_domain_ops = { .xlate = irq_domain_xlate_onecell, }; -void __init icoll_of_init(struct device_node *np, +static void __init icoll_of_init(struct device_node *np, struct device_node *interrupt_parent) { /* diff --git a/arch/arm/mach-mxs/mach-mxs.c b/arch/arm/mach-mxs/mach-mxs.c index 052186713347..e7b781d3788f 100644 --- a/arch/arm/mach-mxs/mach-mxs.c +++ b/arch/arm/mach-mxs/mach-mxs.c @@ -41,8 +41,6 @@ static struct fb_videomode mx23evk_video_modes[] = { .lower_margin = 4, .hsync_len = 1, .vsync_len = 1, - .sync = FB_SYNC_DATA_ENABLE_HIGH_ACT | - FB_SYNC_DOTCLK_FAILING_ACT, }, }; @@ -59,8 +57,6 @@ static struct fb_videomode mx28evk_video_modes[] = { .lower_margin = 10, .hsync_len = 10, .vsync_len = 10, - .sync = FB_SYNC_DATA_ENABLE_HIGH_ACT | - FB_SYNC_DOTCLK_FAILING_ACT, }, }; @@ -77,7 +73,6 @@ static struct fb_videomode m28evk_video_modes[] = { .lower_margin = 45, .hsync_len = 1, .vsync_len = 1, - .sync = FB_SYNC_DATA_ENABLE_HIGH_ACT, }, }; @@ -94,9 +89,7 @@ static struct fb_videomode apx4devkit_video_modes[] = { .lower_margin = 13, .hsync_len = 48, .vsync_len = 3, - .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT | - FB_SYNC_DATA_ENABLE_HIGH_ACT | - FB_SYNC_DOTCLK_FAILING_ACT, + .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT, }, }; @@ -113,9 +106,7 @@ static struct fb_videomode apf28dev_video_modes[] = { .lower_margin = 0x15, .hsync_len = 64, .vsync_len = 4, - .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT | - FB_SYNC_DATA_ENABLE_HIGH_ACT | - FB_SYNC_DOTCLK_FAILING_ACT, + .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT, }, }; @@ -132,7 +123,6 @@ static struct fb_videomode cfa10049_video_modes[] = { .lower_margin = 2, .hsync_len = 15, .vsync_len = 15, - .sync = FB_SYNC_DATA_ENABLE_HIGH_ACT }, }; @@ -259,6 +249,8 @@ static void __init imx23_evk_init(void) mxsfb_pdata.mode_count = ARRAY_SIZE(mx23evk_video_modes); mxsfb_pdata.default_bpp = 32; mxsfb_pdata.ld_intf_width = STMLCDIF_24BIT; + mxsfb_pdata.sync = MXSFB_SYNC_DATA_ENABLE_HIGH_ACT | + MXSFB_SYNC_DOTCLK_FAILING_ACT; } static inline void enable_clk_enet_out(void) @@ -278,6 +270,8 @@ static void __init imx28_evk_init(void) mxsfb_pdata.mode_count = ARRAY_SIZE(mx28evk_video_modes); mxsfb_pdata.default_bpp = 32; mxsfb_pdata.ld_intf_width = STMLCDIF_24BIT; + mxsfb_pdata.sync = MXSFB_SYNC_DATA_ENABLE_HIGH_ACT | + MXSFB_SYNC_DOTCLK_FAILING_ACT; mxs_saif_clkmux_select(MXS_DIGCTL_SAIF_CLKMUX_EXTMSTR0); } @@ -297,6 +291,7 @@ static void __init m28evk_init(void) mxsfb_pdata.mode_count = ARRAY_SIZE(m28evk_video_modes); mxsfb_pdata.default_bpp = 16; mxsfb_pdata.ld_intf_width = STMLCDIF_18BIT; + mxsfb_pdata.sync = MXSFB_SYNC_DATA_ENABLE_HIGH_ACT; } static void __init sc_sps1_init(void) @@ -322,6 +317,8 @@ static void __init apx4devkit_init(void) mxsfb_pdata.mode_count = ARRAY_SIZE(apx4devkit_video_modes); mxsfb_pdata.default_bpp = 32; mxsfb_pdata.ld_intf_width = STMLCDIF_24BIT; + mxsfb_pdata.sync = MXSFB_SYNC_DATA_ENABLE_HIGH_ACT | + MXSFB_SYNC_DOTCLK_FAILING_ACT; } #define ENET0_MDC__GPIO_4_0 MXS_GPIO_NR(4, 0) @@ -402,17 +399,18 @@ static void __init cfa10049_init(void) { enable_clk_enet_out(); update_fec_mac_prop(OUI_CRYSTALFONTZ); + + mxsfb_pdata.mode_list = cfa10049_video_modes; + mxsfb_pdata.mode_count = ARRAY_SIZE(cfa10049_video_modes); + mxsfb_pdata.default_bpp = 32; + mxsfb_pdata.ld_intf_width = STMLCDIF_18BIT; + mxsfb_pdata.sync = MXSFB_SYNC_DATA_ENABLE_HIGH_ACT; } static void __init cfa10037_init(void) { enable_clk_enet_out(); update_fec_mac_prop(OUI_CRYSTALFONTZ); - - mxsfb_pdata.mode_list = cfa10049_video_modes; - mxsfb_pdata.mode_count = ARRAY_SIZE(cfa10049_video_modes); - mxsfb_pdata.default_bpp = 32; - mxsfb_pdata.ld_intf_width = STMLCDIF_18BIT; } static void __init apf28_init(void) @@ -423,6 +421,8 @@ static void __init apf28_init(void) mxsfb_pdata.mode_count = ARRAY_SIZE(apf28dev_video_modes); mxsfb_pdata.default_bpp = 16; mxsfb_pdata.ld_intf_width = STMLCDIF_16BIT; + mxsfb_pdata.sync = MXSFB_SYNC_DATA_ENABLE_HIGH_ACT | + MXSFB_SYNC_DOTCLK_FAILING_ACT; } static void __init mxs_machine_init(void) diff --git a/arch/arm/mach-mxs/mm.c b/arch/arm/mach-mxs/mm.c index a4294aa9f301..e63b7d87acbd 100644 --- a/arch/arm/mach-mxs/mm.c +++ b/arch/arm/mach-mxs/mm.c @@ -18,6 +18,7 @@ #include <mach/mx23.h> #include <mach/mx28.h> +#include <mach/common.h> /* * Define the MX23 memory map. diff --git a/arch/arm/mach-mxs/ocotp.c b/arch/arm/mach-mxs/ocotp.c index 54add60f94c9..1dff46703753 100644 --- a/arch/arm/mach-mxs/ocotp.c +++ b/arch/arm/mach-mxs/ocotp.c @@ -19,6 +19,7 @@ #include <asm/processor.h> /* for cpu_relax() */ #include <mach/mxs.h> +#include <mach/common.h> #define OCOTP_WORD_OFFSET 0x20 #define OCOTP_WORD_COUNT 0x20 diff --git a/arch/arm/mach-omap1/clock_data.c b/arch/arm/mach-omap1/clock_data.c index cb7c6ae2e3fc..6c4f766365a2 100644 --- a/arch/arm/mach-omap1/clock_data.c +++ b/arch/arm/mach-omap1/clock_data.c @@ -543,15 +543,6 @@ static struct clk usb_dc_ck = { /* Direct from ULPD, no parent */ .rate = 48000000, .enable_reg = OMAP1_IO_ADDRESS(SOFT_REQ_REG), - .enable_bit = USB_REQ_EN_SHIFT, -}; - -static struct clk usb_dc_ck7xx = { - .name = "usb_dc_ck", - .ops = &clkops_generic, - /* Direct from ULPD, no parent */ - .rate = 48000000, - .enable_reg = OMAP1_IO_ADDRESS(SOFT_REQ_REG), .enable_bit = SOFT_USB_OTG_DPLL_REQ_SHIFT, }; @@ -727,8 +718,7 @@ static struct omap_clk omap_clks[] = { CLK(NULL, "usb_clko", &usb_clko, CK_16XX | CK_1510 | CK_310), CLK(NULL, "usb_hhc_ck", &usb_hhc_ck1510, CK_1510 | CK_310), CLK(NULL, "usb_hhc_ck", &usb_hhc_ck16xx, CK_16XX), - CLK(NULL, "usb_dc_ck", &usb_dc_ck, CK_16XX), - CLK(NULL, "usb_dc_ck", &usb_dc_ck7xx, CK_7XX), + CLK(NULL, "usb_dc_ck", &usb_dc_ck, CK_16XX | CK_7XX), CLK(NULL, "mclk", &mclk_1510, CK_1510 | CK_310), CLK(NULL, "mclk", &mclk_16xx, CK_16XX), CLK(NULL, "bclk", &bclk_1510, CK_1510 | CK_310), diff --git a/arch/arm/mach-omap1/common.h b/arch/arm/mach-omap1/common.h index fb18831e88aa..14f7e9920479 100644 --- a/arch/arm/mach-omap1/common.h +++ b/arch/arm/mach-omap1/common.h @@ -31,6 +31,8 @@ #include <plat/i2c.h> +#include <mach/irqs.h> + #if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850) void omap7xx_map_io(void); #else diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig index 49ac3dfebef9..8111cd9ff3e5 100644 --- a/arch/arm/mach-omap2/Kconfig +++ b/arch/arm/mach-omap2/Kconfig @@ -311,9 +311,6 @@ config MACH_OMAP_ZOOM2 default y select OMAP_PACKAGE_CBB select REGULATOR_FIXED_VOLTAGE if REGULATOR - select SERIAL_8250 - select SERIAL_8250_CONSOLE - select SERIAL_CORE_CONSOLE config MACH_OMAP_ZOOM3 bool "OMAP3630 Zoom3 board" @@ -321,9 +318,6 @@ config MACH_OMAP_ZOOM3 default y select OMAP_PACKAGE_CBP select REGULATOR_FIXED_VOLTAGE if REGULATOR - select SERIAL_8250 - select SERIAL_8250_CONSOLE - select SERIAL_CORE_CONSOLE config MACH_CM_T35 bool "CompuLab CM-T35/CM-T3730 modules" diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c index 0274ff7a2a2b..e54a48060198 100644 --- a/arch/arm/mach-omap2/board-generic.c +++ b/arch/arm/mach-omap2/board-generic.c @@ -102,6 +102,7 @@ DT_MACHINE_START(OMAP3_DT, "Generic OMAP3 (Flattened Device Tree)") .init_irq = omap_intc_of_init, .handle_irq = omap3_intc_handle_irq, .init_machine = omap_generic_init, + .init_late = omap3_init_late, .init_time = omap3_sync32k_timer_init, .dt_compat = omap3_boards_compat, .restart = omap3xxx_restart, @@ -119,6 +120,7 @@ DT_MACHINE_START(OMAP3_GP_DT, "Generic OMAP3-GP (Flattened Device Tree)") .init_irq = omap_intc_of_init, .handle_irq = omap3_intc_handle_irq, .init_machine = omap_generic_init, + .init_late = omap3_init_late, .init_time = omap3_secure_sync32k_timer_init, .dt_compat = omap3_gp_boards_compat, .restart = omap3xxx_restart, diff --git a/arch/arm/mach-omap2/board-rx51.c b/arch/arm/mach-omap2/board-rx51.c index f7c4616cbb60..d2ea68ea678a 100644 --- a/arch/arm/mach-omap2/board-rx51.c +++ b/arch/arm/mach-omap2/board-rx51.c @@ -17,6 +17,7 @@ #include <linux/io.h> #include <linux/gpio.h> #include <linux/leds.h> +#include <linux/usb/phy.h> #include <linux/usb/musb.h> #include <linux/platform_data/spi-omap2-mcspi.h> @@ -98,6 +99,7 @@ static void __init rx51_init(void) sdrc_params = nokia_get_sdram_timings(); omap_sdrc_init(sdrc_params, sdrc_params); + usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb"); usb_musb_init(&musb_board_data); rx51_peripherals_init(); diff --git a/arch/arm/mach-omap2/cclock44xx_data.c b/arch/arm/mach-omap2/cclock44xx_data.c index 3d58f335f173..0c6834ae1fc4 100644 --- a/arch/arm/mach-omap2/cclock44xx_data.c +++ b/arch/arm/mach-omap2/cclock44xx_data.c @@ -52,6 +52,13 @@ */ #define OMAP4_DPLL_ABE_DEFFREQ 98304000 +/* + * OMAP4 USB DPLL default frequency. In OMAP4430 TRM version V, section + * "3.6.3.9.5 DPLL_USB Preferred Settings" shows that the preferred + * locked frequency for the USB DPLL is 960MHz. + */ +#define OMAP4_DPLL_USB_DEFFREQ 960000000 + /* Root clocks */ DEFINE_CLK_FIXED_RATE(extalt_clkin_ck, CLK_IS_ROOT, 59000000, 0x0); @@ -1011,6 +1018,10 @@ DEFINE_CLK_OMAP_MUX(hsmmc2_fclk, "l3_init_clkdm", hsmmc1_fclk_sel, OMAP4430_CM_L3INIT_MMC2_CLKCTRL, OMAP4430_CLKSEL_MASK, hsmmc1_fclk_parents, func_dmic_abe_gfclk_ops); +DEFINE_CLK_GATE(ocp2scp_usb_phy_phy_48m, "func_48m_fclk", &func_48m_fclk, 0x0, + OMAP4430_CM_L3INIT_USBPHYOCP2SCP_CLKCTRL, + OMAP4430_OPTFCLKEN_PHY_48M_SHIFT, 0x0, NULL); + DEFINE_CLK_GATE(sha2md5_fck, "l3_div_ck", &l3_div_ck, 0x0, OMAP4430_CM_L4SEC_SHA2MD51_CLKCTRL, OMAP4430_MODULEMODE_SWCTRL_SHIFT, 0x0, NULL); @@ -1538,6 +1549,7 @@ static struct omap_clk omap44xx_clks[] = { CLK(NULL, "per_mcbsp4_gfclk", &per_mcbsp4_gfclk, CK_443X), CLK(NULL, "hsmmc1_fclk", &hsmmc1_fclk, CK_443X), CLK(NULL, "hsmmc2_fclk", &hsmmc2_fclk, CK_443X), + CLK(NULL, "ocp2scp_usb_phy_phy_48m", &ocp2scp_usb_phy_phy_48m, CK_443X), CLK(NULL, "sha2md5_fck", &sha2md5_fck, CK_443X), CLK(NULL, "slimbus1_fclk_1", &slimbus1_fclk_1, CK_443X), CLK(NULL, "slimbus1_fclk_0", &slimbus1_fclk_0, CK_443X), @@ -1705,5 +1717,13 @@ int __init omap4xxx_clk_init(void) if (rc) pr_err("%s: failed to configure ABE DPLL!\n", __func__); + /* + * Lock USB DPLL on OMAP4 devices so that the L3INIT power + * domain can transition to retention state when not in use. + */ + rc = clk_set_rate(&dpll_usb_ck, OMAP4_DPLL_USB_DEFFREQ); + if (rc) + pr_err("%s: failed to configure USB DPLL!\n", __func__); + return 0; } diff --git a/arch/arm/mach-omap2/common.h b/arch/arm/mach-omap2/common.h index 0a6b9c7a63da..d6ba13e1c540 100644 --- a/arch/arm/mach-omap2/common.h +++ b/arch/arm/mach-omap2/common.h @@ -108,7 +108,6 @@ void omap35xx_init_late(void); void omap3630_init_late(void); void am35xx_init_late(void); void ti81xx_init_late(void); -void omap4430_init_late(void); int omap2_common_pm_late_init(void); #if defined(CONFIG_SOC_OMAP2420) || defined(CONFIG_SOC_OMAP2430) @@ -294,5 +293,8 @@ extern void omap_reserve(void); struct omap_hwmod; extern int omap_dss_reset(struct omap_hwmod *); +/* SoC specific clock initializer */ +extern int (*omap_clk_init)(void); + #endif /* __ASSEMBLER__ */ #endif /* __ARCH_ARM_MACH_OMAP2PLUS_COMMON_H */ diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c index e4b16c8efe8b..410e1bac7815 100644 --- a/arch/arm/mach-omap2/gpmc.c +++ b/arch/arm/mach-omap2/gpmc.c @@ -1122,9 +1122,6 @@ int gpmc_calc_timings(struct gpmc_timings *gpmc_t, /* TODO: remove, see function definition */ gpmc_convert_ps_to_ns(gpmc_t); - /* Now the GPMC is initialised, unreserve the chip-selects */ - gpmc_cs_map = 0; - return 0; } @@ -1383,6 +1380,9 @@ static int gpmc_probe(struct platform_device *pdev) if (IS_ERR_VALUE(gpmc_setup_irq())) dev_warn(gpmc_dev, "gpmc_setup_irq failed\n"); + /* Now the GPMC is initialised, unreserve the chip-selects */ + gpmc_cs_map = 0; + rc = gpmc_probe_dt(pdev); if (rc < 0) { clk_disable_unprepare(gpmc_l3_clk); diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c index 2c3fdd65387b..5c445ca1e271 100644 --- a/arch/arm/mach-omap2/io.c +++ b/arch/arm/mach-omap2/io.c @@ -55,6 +55,12 @@ #include "prm44xx.h" /* + * omap_clk_init: points to a function that does the SoC-specific + * clock initializations + */ +int (*omap_clk_init)(void); + +/* * The machine specific code may provide the extra mapping besides the * default mapping provided here. */ @@ -397,7 +403,7 @@ void __init omap2420_init_early(void) omap242x_clockdomains_init(); omap2420_hwmod_init(); omap_hwmod_init_postsetup(); - omap2420_clk_init(); + omap_clk_init = omap2420_clk_init; } void __init omap2420_init_late(void) @@ -427,7 +433,7 @@ void __init omap2430_init_early(void) omap243x_clockdomains_init(); omap2430_hwmod_init(); omap_hwmod_init_postsetup(); - omap2430_clk_init(); + omap_clk_init = omap2430_clk_init; } void __init omap2430_init_late(void) @@ -462,7 +468,7 @@ void __init omap3_init_early(void) omap3xxx_clockdomains_init(); omap3xxx_hwmod_init(); omap_hwmod_init_postsetup(); - omap3xxx_clk_init(); + omap_clk_init = omap3xxx_clk_init; } void __init omap3430_init_early(void) @@ -500,7 +506,7 @@ void __init ti81xx_init_early(void) omap3xxx_clockdomains_init(); omap3xxx_hwmod_init(); omap_hwmod_init_postsetup(); - omap3xxx_clk_init(); + omap_clk_init = omap3xxx_clk_init; } void __init omap3_init_late(void) @@ -568,7 +574,7 @@ void __init am33xx_init_early(void) am33xx_clockdomains_init(); am33xx_hwmod_init(); omap_hwmod_init_postsetup(); - am33xx_clk_init(); + omap_clk_init = am33xx_clk_init; } #endif @@ -593,7 +599,7 @@ void __init omap4430_init_early(void) omap44xx_clockdomains_init(); omap44xx_hwmod_init(); omap_hwmod_init_postsetup(); - omap4xxx_clk_init(); + omap_clk_init = omap4xxx_clk_init; } void __init omap4430_init_late(void) diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c index 6a217c98db54..f82cf878d6af 100644 --- a/arch/arm/mach-omap2/mux.c +++ b/arch/arm/mach-omap2/mux.c @@ -211,8 +211,6 @@ static int __init _omap_mux_get_by_name(struct omap_mux_partition *partition, return -EINVAL; } - pr_err("%s: Could not find signal %s\n", __func__, muxname); - return -ENODEV; } @@ -234,6 +232,8 @@ int __init omap_mux_get_by_name(const char *muxname, return mux_mode; } + pr_err("%s: Could not find signal %s\n", __func__, muxname); + return -ENODEV; } @@ -739,8 +739,9 @@ static void __init omap_mux_dbg_create_entry( list_for_each_entry(e, &partition->muxmodes, node) { struct omap_mux *m = &e->mux; - (void)debugfs_create_file(m->muxnames[0], S_IWUSR, mux_dbg_dir, - m, &omap_mux_dbg_signal_fops); + (void)debugfs_create_file(m->muxnames[0], S_IWUSR | S_IRUGO, + mux_dbg_dir, m, + &omap_mux_dbg_signal_fops); } } diff --git a/arch/arm/mach-omap2/omap_hwmod.c b/arch/arm/mach-omap2/omap_hwmod.c index c2c798c08c2b..a202a4785104 100644 --- a/arch/arm/mach-omap2/omap_hwmod.c +++ b/arch/arm/mach-omap2/omap_hwmod.c @@ -1368,7 +1368,9 @@ static void _enable_sysc(struct omap_hwmod *oh) } if (sf & SYSC_HAS_MIDLEMODE) { - if (oh->flags & HWMOD_SWSUP_MSTANDBY) { + if (oh->flags & HWMOD_FORCE_MSTANDBY) { + idlemode = HWMOD_IDLEMODE_FORCE; + } else if (oh->flags & HWMOD_SWSUP_MSTANDBY) { idlemode = HWMOD_IDLEMODE_NO; } else { if (sf & SYSC_HAS_ENAWAKEUP) @@ -1440,7 +1442,8 @@ static void _idle_sysc(struct omap_hwmod *oh) } if (sf & SYSC_HAS_MIDLEMODE) { - if (oh->flags & HWMOD_SWSUP_MSTANDBY) { + if ((oh->flags & HWMOD_SWSUP_MSTANDBY) || + (oh->flags & HWMOD_FORCE_MSTANDBY)) { idlemode = HWMOD_IDLEMODE_FORCE; } else { if (sf & SYSC_HAS_ENAWAKEUP) diff --git a/arch/arm/mach-omap2/omap_hwmod.h b/arch/arm/mach-omap2/omap_hwmod.h index d43d9b608eda..d5dc935f6060 100644 --- a/arch/arm/mach-omap2/omap_hwmod.h +++ b/arch/arm/mach-omap2/omap_hwmod.h @@ -427,8 +427,8 @@ struct omap_hwmod_omap4_prcm { * * HWMOD_SWSUP_SIDLE: omap_hwmod code should manually bring module in and out * of idle, rather than relying on module smart-idle - * HWMOD_SWSUP_MSTDBY: omap_hwmod code should manually bring module in and out - * of standby, rather than relying on module smart-standby + * HWMOD_SWSUP_MSTANDBY: omap_hwmod code should manually bring module in and + * out of standby, rather than relying on module smart-standby * HWMOD_INIT_NO_RESET: don't reset this module at boot - important for * SDRAM controller, etc. XXX probably belongs outside the main hwmod file * XXX Should be HWMOD_SETUP_NO_RESET @@ -459,6 +459,10 @@ struct omap_hwmod_omap4_prcm { * correctly, or this is being abused to deal with some PM latency * issues -- but we're currently suffering from a shortage of * folks who are able to track these issues down properly. + * HWMOD_FORCE_MSTANDBY: Always keep MIDLEMODE bits cleared so that device + * is kept in force-standby mode. Failing to do so causes PM problems + * with musb on OMAP3630 at least. Note that musb has a dedicated register + * to control MSTANDBY signal when MIDLEMODE is set to force-standby. */ #define HWMOD_SWSUP_SIDLE (1 << 0) #define HWMOD_SWSUP_MSTANDBY (1 << 1) @@ -471,6 +475,7 @@ struct omap_hwmod_omap4_prcm { #define HWMOD_16BIT_REG (1 << 8) #define HWMOD_EXT_OPT_MAIN_CLK (1 << 9) #define HWMOD_BLOCK_WFI (1 << 10) +#define HWMOD_FORCE_MSTANDBY (1 << 11) /* * omap_hwmod._int_flags definitions diff --git a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c index ac7e03ec952f..5112d04e7b79 100644 --- a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c @@ -1707,9 +1707,14 @@ static struct omap_hwmod omap3xxx_usbhsotg_hwmod = { * Erratum ID: i479 idle_req / idle_ack mechanism potentially * broken when autoidle is enabled * workaround is to disable the autoidle bit at module level. + * + * Enabling the device in any other MIDLEMODE setting but force-idle + * causes core_pwrdm not enter idle states at least on OMAP3630. + * Note that musb has OTG_FORCESTDBY register that controls MSTANDBY + * signal when MIDLEMODE is set to force-idle. */ .flags = HWMOD_NO_OCP_AUTOIDLE | HWMOD_SWSUP_SIDLE - | HWMOD_SWSUP_MSTANDBY, + | HWMOD_FORCE_MSTANDBY, }; /* usb_otg_hs */ diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c index 0e47d2e1687c..9e0576569e07 100644 --- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c @@ -2714,6 +2714,10 @@ static struct omap_ocp2scp_dev ocp2scp_dev_attr[] = { { } }; +static struct omap_hwmod_opt_clk ocp2scp_usb_phy_opt_clks[] = { + { .role = "48mhz", .clk = "ocp2scp_usb_phy_phy_48m" }, +}; + /* ocp2scp_usb_phy */ static struct omap_hwmod omap44xx_ocp2scp_usb_phy_hwmod = { .name = "ocp2scp_usb_phy", @@ -2728,6 +2732,8 @@ static struct omap_hwmod omap44xx_ocp2scp_usb_phy_hwmod = { }, }, .dev_attr = ocp2scp_dev_attr, + .opt_clks = ocp2scp_usb_phy_opt_clks, + .opt_clks_cnt = ARRAY_SIZE(ocp2scp_usb_phy_opt_clks), }; /* diff --git a/arch/arm/mach-omap2/timer.c b/arch/arm/mach-omap2/timer.c index 2bdd4cf17a8f..f62b509ed08d 100644 --- a/arch/arm/mach-omap2/timer.c +++ b/arch/arm/mach-omap2/timer.c @@ -547,6 +547,8 @@ static inline void __init realtime_counter_init(void) clksrc_nr, clksrc_src) \ void __init omap##name##_gptimer_timer_init(void) \ { \ + if (omap_clk_init) \ + omap_clk_init(); \ omap_dmtimer_init(); \ omap2_gp_clockevent_init((clkev_nr), clkev_src, clkev_prop); \ omap2_gptimer_clocksource_init((clksrc_nr), clksrc_src); \ @@ -556,6 +558,8 @@ void __init omap##name##_gptimer_timer_init(void) \ clksrc_nr, clksrc_src) \ void __init omap##name##_sync32k_timer_init(void) \ { \ + if (omap_clk_init) \ + omap_clk_init(); \ omap_dmtimer_init(); \ omap2_gp_clockevent_init((clkev_nr), clkev_src, clkev_prop); \ /* Enable the use of clocksource="gp_timer" kernel parameter */ \ diff --git a/arch/arm/mach-pxa/raumfeld.c b/arch/arm/mach-pxa/raumfeld.c index af41888acbd6..969b0ba7fa70 100644 --- a/arch/arm/mach-pxa/raumfeld.c +++ b/arch/arm/mach-pxa/raumfeld.c @@ -505,6 +505,7 @@ static struct w1_gpio_platform_data w1_gpio_platform_data = { .pin = GPIO_ONE_WIRE, .is_open_drain = 0, .enable_external_pullup = w1_enable_external_pullup, + .ext_pullup_enable_pin = -EINVAL, }; struct platform_device raumfeld_w1_gpio_device = { diff --git a/arch/arm/mach-s3c24xx/include/mach/irqs.h b/arch/arm/mach-s3c24xx/include/mach/irqs.h index b7a9f4d469e8..1e73f5fa8659 100644 --- a/arch/arm/mach-s3c24xx/include/mach/irqs.h +++ b/arch/arm/mach-s3c24xx/include/mach/irqs.h @@ -188,10 +188,8 @@ #if defined(CONFIG_CPU_S3C2416) #define NR_IRQS (IRQ_S3C2416_I2S1 + 1) -#elif defined(CONFIG_CPU_S3C2443) -#define NR_IRQS (IRQ_S3C2443_AC97+1) #else -#define NR_IRQS (IRQ_S3C2440_AC97+1) +#define NR_IRQS (IRQ_S3C2443_AC97 + 1) #endif /* compatibility define. */ diff --git a/arch/arm/mach-s3c24xx/irq.c b/arch/arm/mach-s3c24xx/irq.c index cb9f5e011e73..d8ba9bee4c7e 100644 --- a/arch/arm/mach-s3c24xx/irq.c +++ b/arch/arm/mach-s3c24xx/irq.c @@ -500,7 +500,7 @@ struct s3c_irq_intc *s3c24xx_init_intc(struct device_node *np, base = (void *)0xfd000000; intc->reg_mask = base + 0xa4; - intc->reg_pending = base + 0x08; + intc->reg_pending = base + 0xa8; irq_num = 20; irq_start = S3C2410_IRQ(32); irq_offset = 4; diff --git a/arch/arm/mach-s5pv210/clock.c b/arch/arm/mach-s5pv210/clock.c index fcdf52dbcc49..f051f53e35b7 100644 --- a/arch/arm/mach-s5pv210/clock.c +++ b/arch/arm/mach-s5pv210/clock.c @@ -214,11 +214,6 @@ static struct clk clk_pcmcdclk2 = { .name = "pcmcdclk", }; -static struct clk dummy_apb_pclk = { - .name = "apb_pclk", - .id = -1, -}; - static struct clk *clkset_vpllsrc_list[] = { [0] = &clk_fin_vpll, [1] = &clk_sclk_hdmi27m, @@ -305,18 +300,6 @@ static struct clk_ops clk_fout_apll_ops = { static struct clk init_clocks_off[] = { { - .name = "dma", - .devname = "dma-pl330.0", - .parent = &clk_hclk_psys.clk, - .enable = s5pv210_clk_ip0_ctrl, - .ctrlbit = (1 << 3), - }, { - .name = "dma", - .devname = "dma-pl330.1", - .parent = &clk_hclk_psys.clk, - .enable = s5pv210_clk_ip0_ctrl, - .ctrlbit = (1 << 4), - }, { .name = "rot", .parent = &clk_hclk_dsys.clk, .enable = s5pv210_clk_ip0_ctrl, @@ -573,6 +556,20 @@ static struct clk clk_hsmmc3 = { .ctrlbit = (1<<19), }; +static struct clk clk_pdma0 = { + .name = "pdma0", + .parent = &clk_hclk_psys.clk, + .enable = s5pv210_clk_ip0_ctrl, + .ctrlbit = (1 << 3), +}; + +static struct clk clk_pdma1 = { + .name = "pdma1", + .parent = &clk_hclk_psys.clk, + .enable = s5pv210_clk_ip0_ctrl, + .ctrlbit = (1 << 4), +}; + static struct clk *clkset_uart_list[] = { [6] = &clk_mout_mpll.clk, [7] = &clk_mout_epll.clk, @@ -1075,6 +1072,8 @@ static struct clk *clk_cdev[] = { &clk_hsmmc1, &clk_hsmmc2, &clk_hsmmc3, + &clk_pdma0, + &clk_pdma1, }; /* Clock initialisation code */ @@ -1333,6 +1332,8 @@ static struct clk_lookup s5pv210_clk_lookup[] = { CLKDEV_INIT(NULL, "spi_busclk0", &clk_p), CLKDEV_INIT("s5pv210-spi.0", "spi_busclk1", &clk_sclk_spi0.clk), CLKDEV_INIT("s5pv210-spi.1", "spi_busclk1", &clk_sclk_spi1.clk), + CLKDEV_INIT("dma-pl330.0", "apb_pclk", &clk_pdma0), + CLKDEV_INIT("dma-pl330.1", "apb_pclk", &clk_pdma1), }; void __init s5pv210_register_clocks(void) @@ -1361,6 +1362,5 @@ void __init s5pv210_register_clocks(void) for (ptr = 0; ptr < ARRAY_SIZE(clk_cdev); ptr++) s3c_disable_clocks(clk_cdev[ptr], 1); - s3c24xx_register_clock(&dummy_apb_pclk); s3c_pwmclk_init(); } diff --git a/arch/arm/mach-s5pv210/mach-goni.c b/arch/arm/mach-s5pv210/mach-goni.c index 3a38f7b34b94..e373de44a8b6 100644 --- a/arch/arm/mach-s5pv210/mach-goni.c +++ b/arch/arm/mach-s5pv210/mach-goni.c @@ -845,7 +845,7 @@ static struct fimc_source_info goni_camera_sensors[] = { .mux_id = 0, .flags = V4L2_MBUS_PCLK_SAMPLE_FALLING | V4L2_MBUS_VSYNC_ACTIVE_LOW, - .bus_type = FIMC_BUS_TYPE_ITU_601, + .fimc_bus_type = FIMC_BUS_TYPE_ITU_601, .board_info = &noon010pc30_board_info, .i2c_bus_num = 0, .clk_frequency = 16000000UL, diff --git a/arch/arm/mach-shmobile/board-marzen.c b/arch/arm/mach-shmobile/board-marzen.c index cdcb799e802f..fec49ebc359a 100644 --- a/arch/arm/mach-shmobile/board-marzen.c +++ b/arch/arm/mach-shmobile/board-marzen.c @@ -32,6 +32,7 @@ #include <linux/smsc911x.h> #include <linux/spi/spi.h> #include <linux/spi/sh_hspi.h> +#include <linux/mmc/host.h> #include <linux/mmc/sh_mobile_sdhi.h> #include <linux/mfd/tmio.h> #include <linux/usb/otg.h> diff --git a/arch/arm/mach-spear3xx/spear3xx.c b/arch/arm/mach-spear3xx/spear3xx.c index f9d754f90c59..d2b3937c4014 100644 --- a/arch/arm/mach-spear3xx/spear3xx.c +++ b/arch/arm/mach-spear3xx/spear3xx.c @@ -14,7 +14,7 @@ #define pr_fmt(fmt) "SPEAr3xx: " fmt #include <linux/amba/pl022.h> -#include <linux/amba/pl08x.h> +#include <linux/amba/pl080.h> #include <linux/io.h> #include <plat/pl080.h> #include <mach/generic.h> diff --git a/arch/arm/mach-ux500/board-mop500-sdi.c b/arch/arm/mach-ux500/board-mop500-sdi.c index 051b62c27102..7f2cb6c5e2c1 100644 --- a/arch/arm/mach-ux500/board-mop500-sdi.c +++ b/arch/arm/mach-ux500/board-mop500-sdi.c @@ -81,7 +81,6 @@ static struct stedma40_chan_cfg mop500_sdi0_dma_cfg_tx = { #endif struct mmci_platform_data mop500_sdi0_data = { - .ios_handler = mop500_sdi0_ios_handler, .ocr_mask = MMC_VDD_29_30, .f_max = 50000000, .capabilities = MMC_CAP_4_BIT_DATA | diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c index b03457881c4b..87d2d7b38ce9 100644 --- a/arch/arm/mach-ux500/board-mop500.c +++ b/arch/arm/mach-ux500/board-mop500.c @@ -12,6 +12,7 @@ #include <linux/init.h> #include <linux/interrupt.h> #include <linux/platform_device.h> +#include <linux/clk.h> #include <linux/io.h> #include <linux/i2c.h> #include <linux/platform_data/i2c-nomadik.h> @@ -439,6 +440,15 @@ static void mop500_prox_deactivate(struct device *dev) regulator_put(prox_regulator); } +void mop500_snowball_ethernet_clock_enable(void) +{ + struct clk *clk; + + clk = clk_get_sys("fsmc", NULL); + if (!IS_ERR(clk)) + clk_prepare_enable(clk); +} + static struct cryp_platform_data u8500_cryp1_platform_data = { .mem_to_engine = { .dir = STEDMA40_MEM_TO_PERIPH, @@ -683,6 +693,8 @@ static void __init snowball_init_machine(void) mop500_audio_init(parent); mop500_uart_init(parent); + mop500_snowball_ethernet_clock_enable(); + /* This board has full regulator constraints */ regulator_has_full_constraints(); } diff --git a/arch/arm/mach-ux500/board-mop500.h b/arch/arm/mach-ux500/board-mop500.h index eaa605f5d90d..d38951be70df 100644 --- a/arch/arm/mach-ux500/board-mop500.h +++ b/arch/arm/mach-ux500/board-mop500.h @@ -104,6 +104,7 @@ void __init mop500_pinmaps_init(void); void __init snowball_pinmaps_init(void); void __init hrefv60_pinmaps_init(void); void mop500_audio_init(struct device *parent); +void mop500_snowball_ethernet_clock_enable(void); int __init mop500_uib_init(void); void mop500_uib_i2c_add(int busnum, struct i2c_board_info *info, diff --git a/arch/arm/mach-ux500/cpu-db8500.c b/arch/arm/mach-ux500/cpu-db8500.c index 19235cf7bbe3..f1a581844372 100644 --- a/arch/arm/mach-ux500/cpu-db8500.c +++ b/arch/arm/mach-ux500/cpu-db8500.c @@ -312,9 +312,10 @@ static void __init u8500_init_machine(void) /* Pinmaps must be in place before devices register */ if (of_machine_is_compatible("st-ericsson,mop500")) mop500_pinmaps_init(); - else if (of_machine_is_compatible("calaosystems,snowball-a9500")) + else if (of_machine_is_compatible("calaosystems,snowball-a9500")) { snowball_pinmaps_init(); - else if (of_machine_is_compatible("st-ericsson,hrefv60+")) + mop500_snowball_ethernet_clock_enable(); + } else if (of_machine_is_compatible("st-ericsson,hrefv60+")) hrefv60_pinmaps_init(); else if (of_machine_is_compatible("st-ericsson,ccu9540")) {} /* TODO: Add pinmaps for ccu9540 board. */ diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig index 025d17328730..4045c4931a30 100644 --- a/arch/arm/mm/Kconfig +++ b/arch/arm/mm/Kconfig @@ -43,7 +43,7 @@ config CPU_ARM740T depends on !MMU select CPU_32v4T select CPU_ABRT_LV4T - select CPU_CACHE_V3 # although the core is v4t + select CPU_CACHE_V4 select CPU_CP15_MPU select CPU_PABRT_LEGACY help @@ -469,9 +469,6 @@ config CPU_PABRT_V7 bool # The cache model -config CPU_CACHE_V3 - bool - config CPU_CACHE_V4 bool diff --git a/arch/arm/mm/Makefile b/arch/arm/mm/Makefile index 4e333fa2756f..9e51be96f635 100644 --- a/arch/arm/mm/Makefile +++ b/arch/arm/mm/Makefile @@ -33,7 +33,6 @@ obj-$(CONFIG_CPU_PABRT_LEGACY) += pabort-legacy.o obj-$(CONFIG_CPU_PABRT_V6) += pabort-v6.o obj-$(CONFIG_CPU_PABRT_V7) += pabort-v7.o -obj-$(CONFIG_CPU_CACHE_V3) += cache-v3.o obj-$(CONFIG_CPU_CACHE_V4) += cache-v4.o obj-$(CONFIG_CPU_CACHE_V4WT) += cache-v4wt.o obj-$(CONFIG_CPU_CACHE_V4WB) += cache-v4wb.o diff --git a/arch/arm/mm/cache-feroceon-l2.c b/arch/arm/mm/cache-feroceon-l2.c index dd3d59122cc3..48bc3c0a87ce 100644 --- a/arch/arm/mm/cache-feroceon-l2.c +++ b/arch/arm/mm/cache-feroceon-l2.c @@ -343,6 +343,7 @@ void __init feroceon_l2_init(int __l2_wt_override) outer_cache.inv_range = feroceon_l2_inv_range; outer_cache.clean_range = feroceon_l2_clean_range; outer_cache.flush_range = feroceon_l2_flush_range; + outer_cache.inv_all = l2_inv_all; enable_l2(); diff --git a/arch/arm/mm/cache-l2x0.c b/arch/arm/mm/cache-l2x0.c index c2f37390308a..c465faca51b0 100644 --- a/arch/arm/mm/cache-l2x0.c +++ b/arch/arm/mm/cache-l2x0.c @@ -299,7 +299,7 @@ static void l2x0_unlock(u32 cache_id) int lockregs; int i; - switch (cache_id) { + switch (cache_id & L2X0_CACHE_ID_PART_MASK) { case L2X0_CACHE_ID_PART_L310: lockregs = 8; break; @@ -333,15 +333,14 @@ void __init l2x0_init(void __iomem *base, u32 aux_val, u32 aux_mask) if (cache_id_part_number_from_dt) cache_id = cache_id_part_number_from_dt; else - cache_id = readl_relaxed(l2x0_base + L2X0_CACHE_ID) - & L2X0_CACHE_ID_PART_MASK; + cache_id = readl_relaxed(l2x0_base + L2X0_CACHE_ID); aux = readl_relaxed(l2x0_base + L2X0_AUX_CTRL); aux &= aux_mask; aux |= aux_val; /* Determine the number of ways */ - switch (cache_id) { + switch (cache_id & L2X0_CACHE_ID_PART_MASK) { case L2X0_CACHE_ID_PART_L310: if (aux & (1 << 16)) ways = 16; @@ -725,7 +724,6 @@ static const struct l2x0_of_data pl310_data = { .flush_all = l2x0_flush_all, .inv_all = l2x0_inv_all, .disable = l2x0_disable, - .set_debug = pl310_set_debug, }, }; @@ -814,9 +812,8 @@ int __init l2x0_of_init(u32 aux_val, u32 aux_mask) data->save(); of_init = true; - l2x0_init(l2x0_base, aux_val, aux_mask); - memcpy(&outer_cache, &data->outer_cache, sizeof(outer_cache)); + l2x0_init(l2x0_base, aux_val, aux_mask); return 0; } diff --git a/arch/arm/mm/cache-v3.S b/arch/arm/mm/cache-v3.S deleted file mode 100644 index 8a3fadece8d3..000000000000 --- a/arch/arm/mm/cache-v3.S +++ /dev/null @@ -1,137 +0,0 @@ -/* - * linux/arch/arm/mm/cache-v3.S - * - * Copyright (C) 1997-2002 Russell king - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -#include <linux/linkage.h> -#include <linux/init.h> -#include <asm/page.h> -#include "proc-macros.S" - -/* - * flush_icache_all() - * - * Unconditionally clean and invalidate the entire icache. - */ -ENTRY(v3_flush_icache_all) - mov pc, lr -ENDPROC(v3_flush_icache_all) - -/* - * flush_user_cache_all() - * - * Invalidate all cache entries in a particular address - * space. - * - * - mm - mm_struct describing address space - */ -ENTRY(v3_flush_user_cache_all) - /* FALLTHROUGH */ -/* - * flush_kern_cache_all() - * - * Clean and invalidate the entire cache. - */ -ENTRY(v3_flush_kern_cache_all) - /* FALLTHROUGH */ - -/* - * flush_user_cache_range(start, end, flags) - * - * Invalidate a range of cache entries in the specified - * address space. - * - * - start - start address (may not be aligned) - * - end - end address (exclusive, may not be aligned) - * - flags - vma_area_struct flags describing address space - */ -ENTRY(v3_flush_user_cache_range) - mov ip, #0 - mcreq p15, 0, ip, c7, c0, 0 @ flush ID cache - mov pc, lr - -/* - * coherent_kern_range(start, end) - * - * Ensure coherency between the Icache and the Dcache in the - * region described by start. If you have non-snooping - * Harvard caches, you need to implement this function. - * - * - start - virtual start address - * - end - virtual end address - */ -ENTRY(v3_coherent_kern_range) - /* FALLTHROUGH */ - -/* - * coherent_user_range(start, end) - * - * Ensure coherency between the Icache and the Dcache in the - * region described by start. If you have non-snooping - * Harvard caches, you need to implement this function. - * - * - start - virtual start address - * - end - virtual end address - */ -ENTRY(v3_coherent_user_range) - mov r0, #0 - mov pc, lr - -/* - * flush_kern_dcache_area(void *page, size_t size) - * - * Ensure no D cache aliasing occurs, either with itself or - * the I cache - * - * - addr - kernel address - * - size - region size - */ -ENTRY(v3_flush_kern_dcache_area) - /* FALLTHROUGH */ - -/* - * dma_flush_range(start, end) - * - * Clean and invalidate the specified virtual address range. - * - * - start - virtual start address - * - end - virtual end address - */ -ENTRY(v3_dma_flush_range) - mov r0, #0 - mcr p15, 0, r0, c7, c0, 0 @ flush ID cache - mov pc, lr - -/* - * dma_unmap_area(start, size, dir) - * - start - kernel virtual start address - * - size - size of region - * - dir - DMA direction - */ -ENTRY(v3_dma_unmap_area) - teq r2, #DMA_TO_DEVICE - bne v3_dma_flush_range - /* FALLTHROUGH */ - -/* - * dma_map_area(start, size, dir) - * - start - kernel virtual start address - * - size - size of region - * - dir - DMA direction - */ -ENTRY(v3_dma_map_area) - mov pc, lr -ENDPROC(v3_dma_unmap_area) -ENDPROC(v3_dma_map_area) - - .globl v3_flush_kern_cache_louis - .equ v3_flush_kern_cache_louis, v3_flush_kern_cache_all - - __INITDATA - - @ define struct cpu_cache_fns (see <asm/cacheflush.h> and proc-macros.S) - define_cache_functions v3 diff --git a/arch/arm/mm/cache-v4.S b/arch/arm/mm/cache-v4.S index 43e5d77be677..a7ba68f59f0c 100644 --- a/arch/arm/mm/cache-v4.S +++ b/arch/arm/mm/cache-v4.S @@ -58,7 +58,7 @@ ENTRY(v4_flush_kern_cache_all) ENTRY(v4_flush_user_cache_range) #ifdef CONFIG_CPU_CP15 mov ip, #0 - mcreq p15, 0, ip, c7, c7, 0 @ flush ID cache + mcr p15, 0, ip, c7, c7, 0 @ flush ID cache mov pc, lr #else /* FALLTHROUGH */ diff --git a/arch/arm/mm/context.c b/arch/arm/mm/context.c index a5a4b2bc42ba..2ac37372ef52 100644 --- a/arch/arm/mm/context.c +++ b/arch/arm/mm/context.c @@ -48,7 +48,7 @@ static DEFINE_RAW_SPINLOCK(cpu_asid_lock); static atomic64_t asid_generation = ATOMIC64_INIT(ASID_FIRST_VERSION); static DECLARE_BITMAP(asid_map, NUM_USER_ASIDS); -static DEFINE_PER_CPU(atomic64_t, active_asids); +DEFINE_PER_CPU(atomic64_t, active_asids); static DEFINE_PER_CPU(u64, reserved_asids); static cpumask_t tlb_flush_pending; @@ -215,6 +215,7 @@ void check_and_switch_context(struct mm_struct *mm, struct task_struct *tsk) if (cpumask_test_and_clear_cpu(cpu, &tlb_flush_pending)) { local_flush_bp_all(); local_flush_tlb_all(); + dummy_flush_tlb_a15_erratum(); } atomic64_set(&per_cpu(active_asids, cpu), asid); diff --git a/arch/arm/mm/dma-mapping.c b/arch/arm/mm/dma-mapping.c index c7e3759f16d3..e9db6b4bf65a 100644 --- a/arch/arm/mm/dma-mapping.c +++ b/arch/arm/mm/dma-mapping.c @@ -342,6 +342,7 @@ static int __init atomic_pool_init(void) { struct dma_pool *pool = &atomic_pool; pgprot_t prot = pgprot_dmacoherent(pgprot_kernel); + gfp_t gfp = GFP_KERNEL | GFP_DMA; unsigned long nr_pages = pool->size >> PAGE_SHIFT; unsigned long *bitmap; struct page *page; @@ -361,8 +362,8 @@ static int __init atomic_pool_init(void) ptr = __alloc_from_contiguous(NULL, pool->size, prot, &page, atomic_pool_init); else - ptr = __alloc_remap_buffer(NULL, pool->size, GFP_KERNEL, prot, - &page, atomic_pool_init); + ptr = __alloc_remap_buffer(NULL, pool->size, gfp, prot, &page, + atomic_pool_init); if (ptr) { int i; diff --git a/arch/arm/mm/mmu.c b/arch/arm/mm/mmu.c index e95a996ab78f..a84ff763ac39 100644 --- a/arch/arm/mm/mmu.c +++ b/arch/arm/mm/mmu.c @@ -34,6 +34,7 @@ #include <asm/mach/pci.h> #include "mm.h" +#include "tcm.h" /* * empty_zero_page is a special page that is used for @@ -598,39 +599,60 @@ static void __init alloc_init_pte(pmd_t *pmd, unsigned long addr, } while (pte++, addr += PAGE_SIZE, addr != end); } -static void __init alloc_init_section(pud_t *pud, unsigned long addr, - unsigned long end, phys_addr_t phys, - const struct mem_type *type) +static void __init map_init_section(pmd_t *pmd, unsigned long addr, + unsigned long end, phys_addr_t phys, + const struct mem_type *type) { - pmd_t *pmd = pmd_offset(pud, addr); - +#ifndef CONFIG_ARM_LPAE /* - * Try a section mapping - end, addr and phys must all be aligned - * to a section boundary. Note that PMDs refer to the individual - * L1 entries, whereas PGDs refer to a group of L1 entries making - * up one logical pointer to an L2 table. + * In classic MMU format, puds and pmds are folded in to + * the pgds. pmd_offset gives the PGD entry. PGDs refer to a + * group of L1 entries making up one logical pointer to + * an L2 table (2MB), where as PMDs refer to the individual + * L1 entries (1MB). Hence increment to get the correct + * offset for odd 1MB sections. + * (See arch/arm/include/asm/pgtable-2level.h) */ - if (type->prot_sect && ((addr | end | phys) & ~SECTION_MASK) == 0) { - pmd_t *p = pmd; - -#ifndef CONFIG_ARM_LPAE - if (addr & SECTION_SIZE) - pmd++; + if (addr & SECTION_SIZE) + pmd++; #endif + do { + *pmd = __pmd(phys | type->prot_sect); + phys += SECTION_SIZE; + } while (pmd++, addr += SECTION_SIZE, addr != end); - do { - *pmd = __pmd(phys | type->prot_sect); - phys += SECTION_SIZE; - } while (pmd++, addr += SECTION_SIZE, addr != end); + flush_pmd_entry(pmd); +} - flush_pmd_entry(p); - } else { +static void __init alloc_init_pmd(pud_t *pud, unsigned long addr, + unsigned long end, phys_addr_t phys, + const struct mem_type *type) +{ + pmd_t *pmd = pmd_offset(pud, addr); + unsigned long next; + + do { /* - * No need to loop; pte's aren't interested in the - * individual L1 entries. + * With LPAE, we must loop over to map + * all the pmds for the given range. */ - alloc_init_pte(pmd, addr, end, __phys_to_pfn(phys), type); - } + next = pmd_addr_end(addr, end); + + /* + * Try a section mapping - addr, next and phys must all be + * aligned to a section boundary. + */ + if (type->prot_sect && + ((addr | next | phys) & ~SECTION_MASK) == 0) { + map_init_section(pmd, addr, next, phys, type); + } else { + alloc_init_pte(pmd, addr, next, + __phys_to_pfn(phys), type); + } + + phys += next - addr; + + } while (pmd++, addr = next, addr != end); } static void __init alloc_init_pud(pgd_t *pgd, unsigned long addr, @@ -641,7 +663,7 @@ static void __init alloc_init_pud(pgd_t *pgd, unsigned long addr, do { next = pud_addr_end(addr, end); - alloc_init_section(pud, addr, next, phys, type); + alloc_init_pmd(pud, addr, next, phys, type); phys += next - addr; } while (pud++, addr = next, addr != end); } @@ -1256,6 +1278,7 @@ void __init paging_init(struct machine_desc *mdesc) dma_contiguous_remap(); devicemaps_init(mdesc); kmap_init(); + tcm_init(); top_pmd = pmd_off_k(0xffff0000); diff --git a/arch/arm/mm/proc-arm740.S b/arch/arm/mm/proc-arm740.S index dc5de5d53f20..fde2d2a794cf 100644 --- a/arch/arm/mm/proc-arm740.S +++ b/arch/arm/mm/proc-arm740.S @@ -77,24 +77,27 @@ __arm740_setup: mcr p15, 0, r0, c6, c0 @ set area 0, default ldr r0, =(CONFIG_DRAM_BASE & 0xFFFFF000) @ base[31:12] of RAM - ldr r1, =(CONFIG_DRAM_SIZE >> 12) @ size of RAM (must be >= 4KB) - mov r2, #10 @ 11 is the minimum (4KB) -1: add r2, r2, #1 @ area size *= 2 - mov r1, r1, lsr #1 + ldr r3, =(CONFIG_DRAM_SIZE >> 12) @ size of RAM (must be >= 4KB) + mov r4, #10 @ 11 is the minimum (4KB) +1: add r4, r4, #1 @ area size *= 2 + movs r3, r3, lsr #1 bne 1b @ count not zero r-shift - orr r0, r0, r2, lsl #1 @ the area register value + orr r0, r0, r4, lsl #1 @ the area register value orr r0, r0, #1 @ set enable bit mcr p15, 0, r0, c6, c1 @ set area 1, RAM ldr r0, =(CONFIG_FLASH_MEM_BASE & 0xFFFFF000) @ base[31:12] of FLASH - ldr r1, =(CONFIG_FLASH_SIZE >> 12) @ size of FLASH (must be >= 4KB) - mov r2, #10 @ 11 is the minimum (4KB) -1: add r2, r2, #1 @ area size *= 2 - mov r1, r1, lsr #1 + ldr r3, =(CONFIG_FLASH_SIZE >> 12) @ size of FLASH (must be >= 4KB) + cmp r3, #0 + moveq r0, #0 + beq 2f + mov r4, #10 @ 11 is the minimum (4KB) +1: add r4, r4, #1 @ area size *= 2 + movs r3, r3, lsr #1 bne 1b @ count not zero r-shift - orr r0, r0, r2, lsl #1 @ the area register value + orr r0, r0, r4, lsl #1 @ the area register value orr r0, r0, #1 @ set enable bit - mcr p15, 0, r0, c6, c2 @ set area 2, ROM/FLASH +2: mcr p15, 0, r0, c6, c2 @ set area 2, ROM/FLASH mov r0, #0x06 mcr p15, 0, r0, c2, c0 @ Region 1&2 cacheable @@ -137,13 +140,14 @@ __arm740_proc_info: .long 0x41807400 .long 0xfffffff0 .long 0 + .long 0 b __arm740_setup .long cpu_arch_name .long cpu_elf_name - .long HWCAP_SWP | HWCAP_HALF | HWCAP_26BIT + .long HWCAP_SWP | HWCAP_HALF | HWCAP_THUMB | HWCAP_26BIT .long cpu_arm740_name .long arm740_processor_functions .long 0 .long 0 - .long v3_cache_fns @ cache model + .long v4_cache_fns @ cache model .size __arm740_proc_info, . - __arm740_proc_info diff --git a/arch/arm/mm/proc-arm920.S b/arch/arm/mm/proc-arm920.S index 2c3b9421ab5e..2556cf1c2da1 100644 --- a/arch/arm/mm/proc-arm920.S +++ b/arch/arm/mm/proc-arm920.S @@ -387,7 +387,7 @@ ENTRY(cpu_arm920_set_pte_ext) /* Suspend/resume support: taken from arch/arm/plat-s3c24xx/sleep.S */ .globl cpu_arm920_suspend_size .equ cpu_arm920_suspend_size, 4 * 3 -#ifdef CONFIG_PM_SLEEP +#ifdef CONFIG_ARM_CPU_SUSPEND ENTRY(cpu_arm920_do_suspend) stmfd sp!, {r4 - r6, lr} mrc p15, 0, r4, c13, c0, 0 @ PID diff --git a/arch/arm/mm/proc-arm926.S b/arch/arm/mm/proc-arm926.S index f1803f7e2972..344c8a548cc0 100644 --- a/arch/arm/mm/proc-arm926.S +++ b/arch/arm/mm/proc-arm926.S @@ -402,7 +402,7 @@ ENTRY(cpu_arm926_set_pte_ext) /* Suspend/resume support: taken from arch/arm/plat-s3c24xx/sleep.S */ .globl cpu_arm926_suspend_size .equ cpu_arm926_suspend_size, 4 * 3 -#ifdef CONFIG_PM_SLEEP +#ifdef CONFIG_ARM_CPU_SUSPEND ENTRY(cpu_arm926_do_suspend) stmfd sp!, {r4 - r6, lr} mrc p15, 0, r4, c13, c0, 0 @ PID diff --git a/arch/arm/mm/proc-mohawk.S b/arch/arm/mm/proc-mohawk.S index 82f9cdc751d6..0b60dd3d742a 100644 --- a/arch/arm/mm/proc-mohawk.S +++ b/arch/arm/mm/proc-mohawk.S @@ -350,7 +350,7 @@ ENTRY(cpu_mohawk_set_pte_ext) .globl cpu_mohawk_suspend_size .equ cpu_mohawk_suspend_size, 4 * 6 -#ifdef CONFIG_PM_SLEEP +#ifdef CONFIG_ARM_CPU_SUSPEND ENTRY(cpu_mohawk_do_suspend) stmfd sp!, {r4 - r9, lr} mrc p14, 0, r4, c6, c0, 0 @ clock configuration, for turbo mode diff --git a/arch/arm/mm/proc-sa1100.S b/arch/arm/mm/proc-sa1100.S index 3aa0da11fd84..d92dfd081429 100644 --- a/arch/arm/mm/proc-sa1100.S +++ b/arch/arm/mm/proc-sa1100.S @@ -172,7 +172,7 @@ ENTRY(cpu_sa1100_set_pte_ext) .globl cpu_sa1100_suspend_size .equ cpu_sa1100_suspend_size, 4 * 3 -#ifdef CONFIG_PM_SLEEP +#ifdef CONFIG_ARM_CPU_SUSPEND ENTRY(cpu_sa1100_do_suspend) stmfd sp!, {r4 - r6, lr} mrc p15, 0, r4, c3, c0, 0 @ domain ID diff --git a/arch/arm/mm/proc-syms.c b/arch/arm/mm/proc-syms.c index 3e6210b4d6d4..054b491ff764 100644 --- a/arch/arm/mm/proc-syms.c +++ b/arch/arm/mm/proc-syms.c @@ -17,7 +17,9 @@ #ifndef MULTI_CPU EXPORT_SYMBOL(cpu_dcache_clean_area); +#ifdef CONFIG_MMU EXPORT_SYMBOL(cpu_set_pte_ext); +#endif #else EXPORT_SYMBOL(processor); #endif diff --git a/arch/arm/mm/proc-v6.S b/arch/arm/mm/proc-v6.S index bcaaa8de9325..5c07ee4fe3eb 100644 --- a/arch/arm/mm/proc-v6.S +++ b/arch/arm/mm/proc-v6.S @@ -138,7 +138,7 @@ ENTRY(cpu_v6_set_pte_ext) /* Suspend/resume support: taken from arch/arm/mach-s3c64xx/sleep.S */ .globl cpu_v6_suspend_size .equ cpu_v6_suspend_size, 4 * 6 -#ifdef CONFIG_PM_SLEEP +#ifdef CONFIG_ARM_CPU_SUSPEND ENTRY(cpu_v6_do_suspend) stmfd sp!, {r4 - r9, lr} mrc p15, 0, r4, c13, c0, 0 @ FCSE/PID diff --git a/arch/arm/mm/proc-v7.S b/arch/arm/mm/proc-v7.S index 3a3c015f8d5c..f584d3f5b37c 100644 --- a/arch/arm/mm/proc-v7.S +++ b/arch/arm/mm/proc-v7.S @@ -420,7 +420,7 @@ __v7_pj4b_proc_info: __v7_ca7mp_proc_info: .long 0x410fc070 .long 0xff0ffff0 - __v7_proc __v7_ca7mp_setup, hwcaps = HWCAP_IDIV + __v7_proc __v7_ca7mp_setup .size __v7_ca7mp_proc_info, . - __v7_ca7mp_proc_info /* @@ -430,10 +430,25 @@ __v7_ca7mp_proc_info: __v7_ca15mp_proc_info: .long 0x410fc0f0 .long 0xff0ffff0 - __v7_proc __v7_ca15mp_setup, hwcaps = HWCAP_IDIV + __v7_proc __v7_ca15mp_setup .size __v7_ca15mp_proc_info, . - __v7_ca15mp_proc_info /* + * Qualcomm Inc. Krait processors. + */ + .type __krait_proc_info, #object +__krait_proc_info: + .long 0x510f0400 @ Required ID value + .long 0xff0ffc00 @ Mask for ID + /* + * Some Krait processors don't indicate support for SDIV and UDIV + * instructions in the ARM instruction set, even though they actually + * do support them. + */ + __v7_proc __v7_setup, hwcaps = HWCAP_IDIV + .size __krait_proc_info, . - __krait_proc_info + + /* * Match any ARMv7 processor core. */ .type __v7_proc_info, #object diff --git a/arch/arm/mm/proc-xsc3.S b/arch/arm/mm/proc-xsc3.S index eb93d6487f35..e8efd83b6f25 100644 --- a/arch/arm/mm/proc-xsc3.S +++ b/arch/arm/mm/proc-xsc3.S @@ -413,7 +413,7 @@ ENTRY(cpu_xsc3_set_pte_ext) .globl cpu_xsc3_suspend_size .equ cpu_xsc3_suspend_size, 4 * 6 -#ifdef CONFIG_PM_SLEEP +#ifdef CONFIG_ARM_CPU_SUSPEND ENTRY(cpu_xsc3_do_suspend) stmfd sp!, {r4 - r9, lr} mrc p14, 0, r4, c6, c0, 0 @ clock configuration, for turbo mode diff --git a/arch/arm/mm/proc-xscale.S b/arch/arm/mm/proc-xscale.S index 25510361aa18..e766f889bfd6 100644 --- a/arch/arm/mm/proc-xscale.S +++ b/arch/arm/mm/proc-xscale.S @@ -528,7 +528,7 @@ ENTRY(cpu_xscale_set_pte_ext) .globl cpu_xscale_suspend_size .equ cpu_xscale_suspend_size, 4 * 6 -#ifdef CONFIG_PM_SLEEP +#ifdef CONFIG_ARM_CPU_SUSPEND ENTRY(cpu_xscale_do_suspend) stmfd sp!, {r4 - r9, lr} mrc p14, 0, r4, c6, c0, 0 @ clock configuration, for turbo mode diff --git a/arch/arm/kernel/tcm.h b/arch/arm/mm/tcm.h index 8015ad434a40..8015ad434a40 100644 --- a/arch/arm/kernel/tcm.h +++ b/arch/arm/mm/tcm.h diff --git a/arch/arm/net/bpf_jit_32.c b/arch/arm/net/bpf_jit_32.c index 6828ef6ce80e..a0bd8a755bdf 100644 --- a/arch/arm/net/bpf_jit_32.c +++ b/arch/arm/net/bpf_jit_32.c @@ -576,7 +576,7 @@ load_ind: /* x = ((*(frame + k)) & 0xf) << 2; */ ctx->seen |= SEEN_X | SEEN_DATA | SEEN_CALL; /* the interpreter should deal with the negative K */ - if (k < 0) + if ((int)k < 0) return -1; /* offset in r1: we might have to take the slow path */ emit_mov_i(r_off, k, ctx); diff --git a/arch/arm/plat-orion/addr-map.c b/arch/arm/plat-orion/addr-map.c index febe3862873c..807ac8e5cbc0 100644 --- a/arch/arm/plat-orion/addr-map.c +++ b/arch/arm/plat-orion/addr-map.c @@ -157,9 +157,12 @@ void __init orion_setup_cpu_mbus_target(const struct orion_addr_map_cfg *cfg, u32 size = readl(ddr_window_cpu_base + DDR_SIZE_CS_OFF(i)); /* - * Chip select enabled? + * We only take care of entries for which the chip + * select is enabled, and that don't have high base + * address bits set (devices can only access the first + * 32 bits of the memory). */ - if (size & 1) { + if ((size & 1) && !(base & 0xF)) { struct mbus_dram_window *w; w = &orion_mbus_dram_info.cs[cs++]; diff --git a/arch/arm/plat-spear/Kconfig b/arch/arm/plat-spear/Kconfig index 739d016eb273..8a08c31b5e20 100644 --- a/arch/arm/plat-spear/Kconfig +++ b/arch/arm/plat-spear/Kconfig @@ -10,7 +10,7 @@ choice config ARCH_SPEAR13XX bool "ST SPEAr13xx with Device Tree" - select ARCH_HAVE_CPUFREQ + select ARCH_HAS_CPUFREQ select ARM_GIC select CPU_V7 select GPIO_SPEAR_SPICS |