diff options
Diffstat (limited to 'arch/arm')
| -rw-r--r-- | arch/arm/boot/dts/omap-zoom-common.dtsi | 2 | ||||
| -rw-r--r-- | arch/arm/boot/dts/omap2.dtsi | 96 | ||||
| -rw-r--r-- | arch/arm/boot/dts/omap2420.dtsi | 23 | ||||
| -rw-r--r-- | arch/arm/boot/dts/omap2430.dtsi | 49 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/Makefile | 6 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/common.h | 1 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/display.c | 78 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/gpmc.c | 58 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/omap-secure.h | 7 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/omap4-common.c | 57 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/prm44xx_54xx.h | 2 |
11 files changed, 199 insertions, 180 deletions
diff --git a/arch/arm/boot/dts/omap-zoom-common.dtsi b/arch/arm/boot/dts/omap-zoom-common.dtsi index b0ee342598f0..68221fab978d 100644 --- a/arch/arm/boot/dts/omap-zoom-common.dtsi +++ b/arch/arm/boot/dts/omap-zoom-common.dtsi @@ -13,7 +13,7 @@ * they probably share the same GPIO IRQ * REVISIT: Add timing support from slls644g.pdf */ - 8250@3,0 { + uart@3,0 { compatible = "ns16550a"; reg = <3 0 0x100>; bank-width = <2>; diff --git a/arch/arm/boot/dts/omap2.dtsi b/arch/arm/boot/dts/omap2.dtsi index a2bfcde858a6..d0c5b37e248c 100644 --- a/arch/arm/boot/dts/omap2.dtsi +++ b/arch/arm/boot/dts/omap2.dtsi @@ -9,6 +9,7 @@ */ #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/pinctrl/omap.h> #include "skeleton.dtsi" @@ -21,6 +22,8 @@ serial0 = &uart1; serial1 = &uart2; serial2 = &uart3; + i2c0 = &i2c1; + i2c1 = &i2c2; }; cpus { @@ -53,6 +56,28 @@ ranges; ti,hwmods = "l3_main"; + aes: aes@480a6000 { + compatible = "ti,omap2-aes"; + ti,hwmods = "aes"; + reg = <0x480a6000 0x50>; + dmas = <&sdma 9 &sdma 10>; + dma-names = "tx", "rx"; + }; + + hdq1w: 1w@480b2000 { + compatible = "ti,omap2420-1w"; + ti,hwmods = "hdq1w"; + reg = <0x480b2000 0x1000>; + interrupts = <58>; + }; + + mailbox: mailbox@48094000 { + compatible = "ti,omap2-mailbox"; + ti,hwmods = "mailbox"; + reg = <0x48094000 0x200>; + interrupts = <26>; + }; + intc: interrupt-controller@1 { compatible = "ti,omap2-intc"; interrupt-controller; @@ -63,6 +88,7 @@ sdma: dma-controller@48056000 { compatible = "ti,omap2430-sdma", "ti,omap2420-sdma"; + ti,hwmods = "dma"; reg = <0x48056000 0x1000>; interrupts = <12>, <13>, @@ -73,21 +99,91 @@ #dma-requests = <64>; }; + i2c1: i2c@48070000 { + compatible = "ti,omap2-i2c"; + ti,hwmods = "i2c1"; + reg = <0x48070000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <56>; + dmas = <&sdma 27 &sdma 28>; + dma-names = "tx", "rx"; + }; + + i2c2: i2c@48072000 { + compatible = "ti,omap2-i2c"; + ti,hwmods = "i2c2"; + reg = <0x48072000 0x80>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <57>; + dmas = <&sdma 29 &sdma 30>; + dma-names = "tx", "rx"; + }; + + mcspi1: mcspi@48098000 { + compatible = "ti,omap2-mcspi"; + ti,hwmods = "mcspi1"; + reg = <0x48098000 0x100>; + interrupts = <65>; + dmas = <&sdma 35 &sdma 36 &sdma 37 &sdma 38 + &sdma 39 &sdma 40 &sdma 41 &sdma 42>; + dma-names = "tx0", "rx0", "tx1", "rx1", + "tx2", "rx2", "tx3", "rx3"; + }; + + mcspi2: mcspi@4809a000 { + compatible = "ti,omap2-mcspi"; + ti,hwmods = "mcspi2"; + reg = <0x4809a000 0x100>; + interrupts = <66>; + dmas = <&sdma 43 &sdma 44 &sdma 45 &sdma 46>; + dma-names = "tx0", "rx0", "tx1", "rx1"; + }; + + rng: rng@480a0000 { + compatible = "ti,omap2-rng"; + ti,hwmods = "rng"; + reg = <0x480a0000 0x50>; + interrupts = <36>; + }; + + sham: sham@480a4000 { + compatible = "ti,omap2-sham"; + ti,hwmods = "sham"; + reg = <0x480a4000 0x64>; + interrupts = <51>; + dmas = <&sdma 13>; + dma-names = "rx"; + }; + uart1: serial@4806a000 { compatible = "ti,omap2-uart"; ti,hwmods = "uart1"; + reg = <0x4806a000 0x2000>; + interrupts = <72>; + dmas = <&sdma 49 &sdma 50>; + dma-names = "tx", "rx"; clock-frequency = <48000000>; }; uart2: serial@4806c000 { compatible = "ti,omap2-uart"; ti,hwmods = "uart2"; + reg = <0x4806c000 0x400>; + interrupts = <73>; + dmas = <&sdma 51 &sdma 52>; + dma-names = "tx", "rx"; clock-frequency = <48000000>; }; uart3: serial@4806e000 { compatible = "ti,omap2-uart"; ti,hwmods = "uart3"; + reg = <0x4806e000 0x400>; + interrupts = <74>; + dmas = <&sdma 53 &sdma 54>; + dma-names = "tx", "rx"; clock-frequency = <48000000>; }; diff --git a/arch/arm/boot/dts/omap2420.dtsi b/arch/arm/boot/dts/omap2420.dtsi index c8f9c55169ea..60c605de22dd 100644 --- a/arch/arm/boot/dts/omap2420.dtsi +++ b/arch/arm/boot/dts/omap2420.dtsi @@ -114,6 +114,15 @@ dma-names = "tx", "rx"; }; + msdi1: mmc@4809c000 { + compatible = "ti,omap2420-mmc"; + ti,hwmods = "msdi1"; + reg = <0x4809c000 0x80>; + interrupts = <83>; + dmas = <&sdma 61 &sdma 62>; + dma-names = "tx", "rx"; + }; + timer1: timer@48028000 { compatible = "ti,omap2420-timer"; reg = <0x48028000 0x400>; @@ -121,5 +130,19 @@ ti,hwmods = "timer1"; ti,timer-alwon; }; + + wd_timer2: wdt@48022000 { + compatible = "ti,omap2-wdt"; + ti,hwmods = "wd_timer2"; + reg = <0x48022000 0x80>; + }; }; }; + +&i2c1 { + compatible = "ti,omap2420-i2c"; +}; + +&i2c2 { + compatible = "ti,omap2420-i2c"; +}; diff --git a/arch/arm/boot/dts/omap2430.dtsi b/arch/arm/boot/dts/omap2430.dtsi index c535a5a2b27f..d624345666f5 100644 --- a/arch/arm/boot/dts/omap2430.dtsi +++ b/arch/arm/boot/dts/omap2430.dtsi @@ -175,6 +175,25 @@ dma-names = "tx", "rx"; }; + mmc1: mmc@4809c000 { + compatible = "ti,omap2-hsmmc"; + reg = <0x4809c000 0x200>; + interrupts = <83>; + ti,hwmods = "mmc1"; + ti,dual-volt; + dmas = <&sdma 61>, <&sdma 62>; + dma-names = "tx", "rx"; + }; + + mmc2: mmc@480b4000 { + compatible = "ti,omap2-hsmmc"; + reg = <0x480b4000 0x200>; + interrupts = <86>; + ti,hwmods = "mmc2"; + dmas = <&sdma 47>, <&sdma 48>; + dma-names = "tx", "rx"; + }; + timer1: timer@49018000 { compatible = "ti,omap2420-timer"; reg = <0x49018000 0x400>; @@ -182,5 +201,35 @@ ti,hwmods = "timer1"; ti,timer-alwon; }; + + mcspi3: mcspi@480b8000 { + compatible = "ti,omap2-mcspi"; + ti,hwmods = "mcspi3"; + reg = <0x480b8000 0x100>; + interrupts = <91>; + dmas = <&sdma 15 &sdma 16 &sdma 23 &sdma 24>; + dma-names = "tx0", "rx0", "tx1", "rx1"; + }; + + usb_otg_hs: usb_otg_hs@480ac000 { + compatible = "ti,omap2-musb"; + ti,hwmods = "usb_otg_hs"; + reg = <0x480ac000 0x1000>; + interrupts = <93>; + }; + + wd_timer2: wdt@49016000 { + compatible = "ti,omap2-wdt"; + ti,hwmods = "wd_timer2"; + reg = <0x49016000 0x80>; + }; }; }; + +&i2c1 { + compatible = "ti,omap2430-i2c"; +}; + +&i2c2 { + compatible = "ti,omap2430-i2c"; +}; diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index 1f25f3e99c05..adcef406ff0a 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -19,11 +19,11 @@ secure-common = omap-smc.o omap-secure.o obj-$(CONFIG_ARCH_OMAP2) += $(omap-2-3-common) $(hwmod-common) obj-$(CONFIG_ARCH_OMAP3) += $(omap-2-3-common) $(hwmod-common) $(secure-common) -obj-$(CONFIG_ARCH_OMAP4) += prm44xx.o $(hwmod-common) $(secure-common) +obj-$(CONFIG_ARCH_OMAP4) += $(hwmod-common) $(secure-common) obj-$(CONFIG_SOC_AM33XX) += irq.o $(hwmod-common) -obj-$(CONFIG_SOC_OMAP5) += prm44xx.o $(hwmod-common) $(secure-common) +obj-$(CONFIG_SOC_OMAP5) += $(hwmod-common) $(secure-common) obj-$(CONFIG_SOC_AM43XX) += $(hwmod-common) $(secure-common) -obj-$(CONFIG_SOC_DRA7XX) += prm44xx.o $(hwmod-common) $(secure-common) +obj-$(CONFIG_SOC_DRA7XX) += $(hwmod-common) $(secure-common) ifneq ($(CONFIG_SND_OMAP_SOC_MCBSP),) obj-y += mcbsp.o diff --git a/arch/arm/mach-omap2/common.h b/arch/arm/mach-omap2/common.h index f7644febee81..e30ef6797c63 100644 --- a/arch/arm/mach-omap2/common.h +++ b/arch/arm/mach-omap2/common.h @@ -299,7 +299,6 @@ struct omap_sdrc_params; extern void omap_sdrc_init(struct omap_sdrc_params *sdrc_cs0, struct omap_sdrc_params *sdrc_cs1); struct omap2_hsmmc_info; -extern int omap4_twl6030_hsmmc_init(struct omap2_hsmmc_info *controllers); extern void omap_reserve(void); struct omap_hwmod; diff --git a/arch/arm/mach-omap2/display.c b/arch/arm/mach-omap2/display.c index a4e536b11ec9..58347bb874a0 100644 --- a/arch/arm/mach-omap2/display.c +++ b/arch/arm/mach-omap2/display.c @@ -32,7 +32,6 @@ #include "soc.h" #include "iomap.h" -#include "mux.h" #include "control.h" #include "display.h" #include "prm.h" @@ -102,90 +101,13 @@ static const struct omap_dss_hwmod_data omap4_dss_hwmod_data[] __initconst = { { "dss_hdmi", "omapdss_hdmi", -1 }, }; -static void __init omap4_tpd12s015_mux_pads(void) -{ - omap_mux_init_signal("hdmi_cec", - OMAP_PIN_INPUT_PULLUP); - omap_mux_init_signal("hdmi_ddc_scl", - OMAP_PIN_INPUT_PULLUP); - omap_mux_init_signal("hdmi_ddc_sda", - OMAP_PIN_INPUT_PULLUP); -} - -static void __init omap4_hdmi_mux_pads(enum omap_hdmi_flags flags) -{ - u32 reg; - u16 control_i2c_1; - - /* - * CONTROL_I2C_1: HDMI_DDC_SDA_PULLUPRESX (bit 28) and - * HDMI_DDC_SCL_PULLUPRESX (bit 24) are set to disable - * internal pull up resistor. - */ - if (flags & OMAP_HDMI_SDA_SCL_EXTERNAL_PULLUP) { - control_i2c_1 = OMAP4_CTRL_MODULE_PAD_CORE_CONTROL_I2C_1; - reg = omap4_ctrl_pad_readl(control_i2c_1); - reg |= (OMAP4_HDMI_DDC_SDA_PULLUPRESX_MASK | - OMAP4_HDMI_DDC_SCL_PULLUPRESX_MASK); - omap4_ctrl_pad_writel(reg, control_i2c_1); - } -} - -static int omap4_dsi_mux_pads(int dsi_id, unsigned lanes) -{ - u32 enable_mask, enable_shift; - u32 pipd_mask, pipd_shift; - u32 reg; - - if (dsi_id == 0) { - enable_mask = OMAP4_DSI1_LANEENABLE_MASK; - enable_shift = OMAP4_DSI1_LANEENABLE_SHIFT; - pipd_mask = OMAP4_DSI1_PIPD_MASK; - pipd_shift = OMAP4_DSI1_PIPD_SHIFT; - } else if (dsi_id == 1) { - enable_mask = OMAP4_DSI2_LANEENABLE_MASK; - enable_shift = OMAP4_DSI2_LANEENABLE_SHIFT; - pipd_mask = OMAP4_DSI2_PIPD_MASK; - pipd_shift = OMAP4_DSI2_PIPD_SHIFT; - } else { - return -ENODEV; - } - - reg = omap4_ctrl_pad_readl(OMAP4_CTRL_MODULE_PAD_CORE_CONTROL_DSIPHY); - - reg &= ~enable_mask; - reg &= ~pipd_mask; - - reg |= (lanes << enable_shift) & enable_mask; - reg |= (lanes << pipd_shift) & pipd_mask; - - omap4_ctrl_pad_writel(reg, OMAP4_CTRL_MODULE_PAD_CORE_CONTROL_DSIPHY); - - return 0; -} - -int __init omap_hdmi_init(enum omap_hdmi_flags flags) -{ - if (cpu_is_omap44xx()) { - omap4_hdmi_mux_pads(flags); - omap4_tpd12s015_mux_pads(); - } - - return 0; -} - static int omap_dsi_enable_pads(int dsi_id, unsigned lane_mask) { - if (cpu_is_omap44xx()) - return omap4_dsi_mux_pads(dsi_id, lane_mask); - return 0; } static void omap_dsi_disable_pads(int dsi_id, unsigned lane_mask) { - if (cpu_is_omap44xx()) - omap4_dsi_mux_pads(dsi_id, 0); } static int omap_dss_set_min_bus_tput(struct device *dev, unsigned long tput) diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c index 81de56251955..d24926e6340f 100644 --- a/arch/arm/mach-omap2/gpmc.c +++ b/arch/arm/mach-omap2/gpmc.c @@ -1502,6 +1502,22 @@ static int gpmc_probe_generic_child(struct platform_device *pdev, } /* + * For some GPMC devices we still need to rely on the bootloader + * timings because the devices can be connected via FPGA. So far + * the list is smc91x on the omap2 SDP boards, and 8250 on zooms. + * REVISIT: Add timing support from slls644g.pdf and from the + * lan91c96 manual. + */ + if (of_device_is_compatible(child, "ns16550a") || + of_device_is_compatible(child, "smsc,lan91c94") || + of_device_is_compatible(child, "smsc,lan91c111")) { + dev_warn(&pdev->dev, + "%s using bootloader timings on CS%d\n", + child->name, cs); + goto no_timings; + } + + /* * FIXME: gpmc_cs_request() will map the CS to an arbitary * location in the gpmc address space. When booting with * device-tree we want the NOR flash to be mapped to the @@ -1529,6 +1545,7 @@ static int gpmc_probe_generic_child(struct platform_device *pdev, gpmc_read_timings_dt(child, &gpmc_t); gpmc_cs_set_timings(cs, &gpmc_t); +no_timings: if (of_platform_device_create(child, NULL, &pdev->dev)) return 0; @@ -1541,42 +1558,6 @@ err: return ret; } -/* - * REVISIT: Add timing support from slls644g.pdf - */ -static int gpmc_probe_8250(struct platform_device *pdev, - struct device_node *child) -{ - struct resource res; - unsigned long base; - int ret, cs; - - if (of_property_read_u32(child, "reg", &cs) < 0) { - dev_err(&pdev->dev, "%s has no 'reg' property\n", - child->full_name); - return -ENODEV; - } - - if (of_address_to_resource(child, 0, &res) < 0) { - dev_err(&pdev->dev, "%s has malformed 'reg' property\n", - child->full_name); - return -ENODEV; - } - - ret = gpmc_cs_request(cs, resource_size(&res), &base); - if (ret < 0) { - dev_err(&pdev->dev, "cannot request GPMC CS %d\n", cs); - return ret; - } - - if (of_platform_device_create(child, NULL, &pdev->dev)) - return 0; - - dev_err(&pdev->dev, "failed to create gpmc child %s\n", child->name); - - return -ENODEV; -} - static int gpmc_probe_dt(struct platform_device *pdev) { int ret; @@ -1618,10 +1599,9 @@ static int gpmc_probe_dt(struct platform_device *pdev) else if (of_node_cmp(child->name, "onenand") == 0) ret = gpmc_probe_onenand_child(pdev, child); else if (of_node_cmp(child->name, "ethernet") == 0 || - of_node_cmp(child->name, "nor") == 0) + of_node_cmp(child->name, "nor") == 0 || + of_node_cmp(child->name, "uart") == 0) ret = gpmc_probe_generic_child(pdev, child); - else if (of_node_cmp(child->name, "8250") == 0) - ret = gpmc_probe_8250(pdev, child); if (WARN(ret < 0, "%s: probing gpmc child %s failed\n", __func__, child->full_name)) diff --git a/arch/arm/mach-omap2/omap-secure.h b/arch/arm/mach-omap2/omap-secure.h index 8cc7d331437d..3e97c6c8ecf1 100644 --- a/arch/arm/mach-omap2/omap-secure.h +++ b/arch/arm/mach-omap2/omap-secure.h @@ -76,6 +76,13 @@ static inline void omap_barrier_reserve_memblock(void) { } #endif +#ifdef CONFIG_SOC_HAS_REALTIME_COUNTER void set_cntfreq(void); +#else +static inline void set_cntfreq(void) +{ +} +#endif + #endif /* __ASSEMBLER__ */ #endif /* OMAP_ARCH_OMAP_SECURE_H */ diff --git a/arch/arm/mach-omap2/omap4-common.c b/arch/arm/mach-omap2/omap4-common.c index 57911430324e..b39efd46abf9 100644 --- a/arch/arm/mach-omap2/omap4-common.c +++ b/arch/arm/mach-omap2/omap4-common.c @@ -35,7 +35,6 @@ #include "iomap.h" #include "common.h" #include "mmc.h" -#include "hsmmc.h" #include "prminst44xx.h" #include "prcm_mpu44xx.h" #include "omap4-sar-layout.h" @@ -284,59 +283,3 @@ skip_errata_init: omap_wakeupgen_init(); irqchip_init(); } - -#if defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE) -static int omap4_twl6030_hsmmc_late_init(struct device *dev) -{ - int irq = 0; - struct platform_device *pdev = container_of(dev, - struct platform_device, dev); - struct omap_mmc_platform_data *pdata = dev->platform_data; - - /* Setting MMC1 Card detect Irq */ - if (pdev->id == 0) { - irq = twl6030_mmc_card_detect_config(); - if (irq < 0) { - dev_err(dev, "%s: Error card detect config(%d)\n", - __func__, irq); - return irq; - } - pdata->slots[0].card_detect_irq = irq; - pdata->slots[0].card_detect = twl6030_mmc_card_detect; - } - return 0; -} - -static __init void omap4_twl6030_hsmmc_set_late_init(struct device *dev) -{ - struct omap_mmc_platform_data *pdata; - - /* dev can be null if CONFIG_MMC_OMAP_HS is not set */ - if (!dev) { - pr_err("Failed %s\n", __func__); - return; - } - pdata = dev->platform_data; - pdata->init = omap4_twl6030_hsmmc_late_init; -} - -int __init omap4_twl6030_hsmmc_init(struct omap2_hsmmc_info *controllers) -{ - struct omap2_hsmmc_info *c; - - omap_hsmmc_init(controllers); - for (c = controllers; c->mmc; c++) { - /* pdev can be null if CONFIG_MMC_OMAP_HS is not set */ - if (!c->pdev) - continue; - omap4_twl6030_hsmmc_set_late_init(&c->pdev->dev); - } - - return 0; -} -#else -int __init omap4_twl6030_hsmmc_init(struct omap2_hsmmc_info *controllers) -{ - return 0; -} -#endif diff --git a/arch/arm/mach-omap2/prm44xx_54xx.h b/arch/arm/mach-omap2/prm44xx_54xx.h index 7a976065e138..8d95aa543ef5 100644 --- a/arch/arm/mach-omap2/prm44xx_54xx.h +++ b/arch/arm/mach-omap2/prm44xx_54xx.h @@ -43,7 +43,7 @@ extern void omap4_prm_vcvp_write(u32 val, u8 offset); extern u32 omap4_prm_vcvp_rmw(u32 mask, u32 bits, u8 offset); #if defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_SOC_OMAP5) || \ - defined(CONFIG_SOC_DRA7XX) + defined(CONFIG_SOC_DRA7XX) || defined(CONFIG_SOC_AM43XX) void omap44xx_prm_reconfigure_io_chain(void); #else static inline void omap44xx_prm_reconfigure_io_chain(void) |