diff options
Diffstat (limited to 'arch/arm')
57 files changed, 4013 insertions, 212 deletions
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index cf8a99f19dc4..233a222752c0 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -603,6 +603,7 @@ config ARCH_SA1100 select ARCH_SPARSEMEM_ENABLE select ARCH_MTD_XIP select ARCH_HAS_CPUFREQ + select CPU_FREQ select GENERIC_GPIO select GENERIC_TIME select GENERIC_CLOCKEVENTS @@ -1359,13 +1360,9 @@ source "drivers/cpufreq/Kconfig" config CPU_FREQ_SA1100 bool - depends on CPU_FREQ && (SA1100_H3100 || SA1100_H3600 || SA1100_LART || SA1100_PLEB || SA1100_BADGE4 || SA1100_HACKKIT) - default y config CPU_FREQ_SA1110 bool - depends on CPU_FREQ && (SA1100_ASSABET || SA1100_CERF || SA1100_PT_SYSTEM3) - default y config CPU_FREQ_INTEGRATOR tristate "CPUfreq driver for ARM Integrator CPUs" diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug index ff54c23d085e..5cb9326df7a7 100644 --- a/arch/arm/Kconfig.debug +++ b/arch/arm/Kconfig.debug @@ -71,6 +71,14 @@ config DEBUG_LL in the kernel. This is helpful if you are debugging code that executes before the console is initialized. +config EARLY_PRINTK + bool "Early printk" + depends on DEBUG_LL + help + Say Y here if you want to have an early console using the + kernel low-level debugging functions. Add earlyprintk to your + kernel parameters to enable this console. + config DEBUG_ICEDCC bool "Kernel low-level debugging via EmbeddedICE DCC channel" depends on DEBUG_LL diff --git a/arch/arm/configs/zeus_defconfig b/arch/arm/configs/zeus_defconfig new file mode 100644 index 000000000000..823b11e7091a --- /dev/null +++ b/arch/arm/configs/zeus_defconfig @@ -0,0 +1,2032 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.32 +# Tue Dec 8 20:27:05 2009 +# +CONFIG_ARM=y +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +CONFIG_GENERIC_GPIO=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_HARDIRQS=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_ARCH_HAS_CPUFREQ=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_ARCH_MTD_XIP=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y +CONFIG_VECTORS_BASE=0xffff0000 +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" +CONFIG_CONSTRUCTORS=y + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_AUDIT is not set + +# +# RCU Subsystem +# +# CONFIG_TREE_RCU is not set +# CONFIG_TREE_PREEMPT_RCU is not set +CONFIG_TINY_RCU=y +# CONFIG_TREE_RCU_TRACE is not set +# CONFIG_IKCONFIG is not set +CONFIG_LOG_BUF_SHIFT=13 +# CONFIG_GROUP_SCHED is not set +# CONFIG_CGROUPS is not set +# CONFIG_SYSFS_DEPRECATED_V2 is not set +# CONFIG_RELAY is not set +CONFIG_NAMESPACES=y +# CONFIG_UTS_NS is not set +# CONFIG_IPC_NS is not set +# CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set +# CONFIG_NET_NS is not set +# CONFIG_BLK_DEV_INITRD is not set +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +CONFIG_SYSCTL=y +CONFIG_ANON_INODES=y +# CONFIG_EMBEDDED is not set +CONFIG_UID16=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_AIO=y + +# +# Kernel Performance Events And Counters +# +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_SLUB_DEBUG=y +CONFIG_COMPAT_BRK=y +# CONFIG_SLAB is not set +CONFIG_SLUB=y +# CONFIG_SLOB is not set +# CONFIG_PROFILING is not set +CONFIG_HAVE_OPROFILE=y +# CONFIG_KPROBES is not set +CONFIG_HAVE_KPROBES=y +CONFIG_HAVE_KRETPROBES=y +CONFIG_HAVE_CLK=y + +# +# GCOV-based kernel profiling +# +# CONFIG_SLOW_WORK is not set +CONFIG_HAVE_GENERIC_DMA_COHERENT=y +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_BLOCK=y +CONFIG_LBDAF=y +# CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_DEADLINE=y +# CONFIG_IOSCHED_CFQ is not set +CONFIG_DEFAULT_DEADLINE=y +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="deadline" +# CONFIG_INLINE_SPIN_TRYLOCK is not set +# CONFIG_INLINE_SPIN_TRYLOCK_BH is not set +# CONFIG_INLINE_SPIN_LOCK is not set +# CONFIG_INLINE_SPIN_LOCK_BH is not set +# CONFIG_INLINE_SPIN_LOCK_IRQ is not set +# CONFIG_INLINE_SPIN_LOCK_IRQSAVE is not set +CONFIG_INLINE_SPIN_UNLOCK=y +# CONFIG_INLINE_SPIN_UNLOCK_BH is not set +CONFIG_INLINE_SPIN_UNLOCK_IRQ=y +# CONFIG_INLINE_SPIN_UNLOCK_IRQRESTORE is not set +# CONFIG_INLINE_READ_TRYLOCK is not set +# CONFIG_INLINE_READ_LOCK is not set +# CONFIG_INLINE_READ_LOCK_BH is not set +# CONFIG_INLINE_READ_LOCK_IRQ is not set +# CONFIG_INLINE_READ_LOCK_IRQSAVE is not set +CONFIG_INLINE_READ_UNLOCK=y +# CONFIG_INLINE_READ_UNLOCK_BH is not set +CONFIG_INLINE_READ_UNLOCK_IRQ=y +# CONFIG_INLINE_READ_UNLOCK_IRQRESTORE is not set +# CONFIG_INLINE_WRITE_TRYLOCK is not set +# CONFIG_INLINE_WRITE_LOCK is not set +# CONFIG_INLINE_WRITE_LOCK_BH is not set +# CONFIG_INLINE_WRITE_LOCK_IRQ is not set +# CONFIG_INLINE_WRITE_LOCK_IRQSAVE is not set +CONFIG_INLINE_WRITE_UNLOCK=y +# CONFIG_INLINE_WRITE_UNLOCK_BH is not set +CONFIG_INLINE_WRITE_UNLOCK_IRQ=y +# CONFIG_INLINE_WRITE_UNLOCK_IRQRESTORE is not set +# CONFIG_MUTEX_SPIN_ON_OWNER is not set +CONFIG_FREEZER=y + +# +# System Type +# +CONFIG_MMU=y +# CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_VERSATILE is not set +# CONFIG_ARCH_AT91 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_GEMINI is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_EP93XX is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_MXC is not set +# CONFIG_ARCH_STMP3XXX is not set +# CONFIG_ARCH_NETX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_NOMADIK is not set +# CONFIG_ARCH_IOP13XX is not set +# CONFIG_ARCH_IOP32X is not set +# CONFIG_ARCH_IOP33X is not set +# CONFIG_ARCH_IXP23XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_DOVE is not set +# CONFIG_ARCH_KIRKWOOD is not set +# CONFIG_ARCH_LOKI is not set +# CONFIG_ARCH_MV78XX0 is not set +# CONFIG_ARCH_ORION5X is not set +# CONFIG_ARCH_MMP is not set +# CONFIG_ARCH_KS8695 is not set +# CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_W90X900 is not set +# CONFIG_ARCH_PNX4008 is not set +CONFIG_ARCH_PXA=y +# CONFIG_ARCH_MSM is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_S3C64XX is not set +# CONFIG_ARCH_S5PC1XX is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_U300 is not set +# CONFIG_ARCH_DAVINCI is not set +# CONFIG_ARCH_OMAP is not set +# CONFIG_ARCH_BCMRING is not set +# CONFIG_ARCH_U8500 is not set + +# +# Intel PXA2xx/PXA3xx Implementations +# + +# +# Intel/Marvell Dev Platforms (sorted by hardware release time) +# +# CONFIG_ARCH_LUBBOCK is not set +# CONFIG_MACH_MAINSTONE is not set +# CONFIG_MACH_ZYLONITE300 is not set +# CONFIG_MACH_ZYLONITE320 is not set +# CONFIG_MACH_LITTLETON is not set +# CONFIG_MACH_TAVOREVB is not set +# CONFIG_MACH_SAAR is not set + +# +# Third Party Dev Platforms (sorted by vendor name) +# +# CONFIG_ARCH_PXA_IDP is not set +# CONFIG_ARCH_VIPER is not set +CONFIG_MACH_ARCOM_ZEUS=y +# CONFIG_MACH_BALLOON3 is not set +# CONFIG_MACH_CSB726 is not set +# CONFIG_MACH_ARMCORE is not set +# CONFIG_MACH_EM_X270 is not set +# CONFIG_MACH_EXEDA is not set +# CONFIG_MACH_CM_X300 is not set +# CONFIG_ARCH_GUMSTIX is not set +# CONFIG_MACH_INTELMOTE2 is not set +# CONFIG_MACH_STARGATE2 is not set +# CONFIG_MACH_XCEP is not set +# CONFIG_TRIZEPS_PXA is not set +CONFIG_ARCOM_PCMCIA=y +# CONFIG_MACH_LOGICPD_PXA270 is not set +# CONFIG_MACH_PCM027 is not set +# CONFIG_MACH_COLIBRI is not set +# CONFIG_MACH_COLIBRI300 is not set +# CONFIG_MACH_COLIBRI320 is not set + +# +# End-user Products (sorted by vendor name) +# +# CONFIG_MACH_H4700 is not set +# CONFIG_MACH_H5000 is not set +# CONFIG_MACH_HIMALAYA is not set +# CONFIG_MACH_MAGICIAN is not set +# CONFIG_MACH_MIOA701 is not set +# CONFIG_PXA_EZX is not set +# CONFIG_MACH_MP900C is not set +# CONFIG_ARCH_PXA_PALM is not set +# CONFIG_PXA_SHARPSL is not set +# CONFIG_ARCH_PXA_ESERIES is not set +CONFIG_PXA27x=y +CONFIG_PXA_SSP=y +CONFIG_PXA_HAVE_BOARD_IRQS=y +CONFIG_PXA_HAVE_ISA_IRQS=y +CONFIG_PLAT_PXA=y + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_XSCALE=y +CONFIG_CPU_32v5=y +CONFIG_CPU_ABRT_EV5T=y +CONFIG_CPU_PABRT_LEGACY=y +CONFIG_CPU_CACHE_VIVT=y +CONFIG_CPU_TLB_V4WBI=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y + +# +# Processor Features +# +CONFIG_ARM_THUMB=y +# CONFIG_CPU_DCACHE_DISABLE is not set +CONFIG_ARM_L1_CACHE_SHIFT=5 +CONFIG_IWMMXT=y +CONFIG_XSCALE_PMU=y +CONFIG_COMMON_CLKDEV=y + +# +# Bus support +# +CONFIG_ISA=y +# CONFIG_PCI_SYSCALL is not set +# CONFIG_ARCH_SUPPORTS_MSI is not set +CONFIG_PCCARD=m +CONFIG_PCMCIA=m +CONFIG_PCMCIA_LOAD_CIS=y +CONFIG_PCMCIA_IOCTL=y + +# +# PC-card bridges +# +# CONFIG_I82365 is not set +# CONFIG_TCIC is not set +CONFIG_PCMCIA_SOC_COMMON=m +CONFIG_PCMCIA_PXA2XX=m +# CONFIG_PCMCIA_DEBUG is not set +CONFIG_PCMCIA_PROBE=y + +# +# Kernel Features +# +CONFIG_TICK_ONESHOT=y +# CONFIG_NO_HZ is not set +# CONFIG_HIGH_RES_TIMERS is not set +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +CONFIG_VMSPLIT_3G=y +# CONFIG_VMSPLIT_2G is not set +# CONFIG_VMSPLIT_1G is not set +CONFIG_PAGE_OFFSET=0xC0000000 +CONFIG_PREEMPT_NONE=y +# CONFIG_PREEMPT_VOLUNTARY is not set +# CONFIG_PREEMPT is not set +CONFIG_HZ=100 +CONFIG_AEABI=y +CONFIG_OABI_COMPAT=y +# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set +# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set +# CONFIG_HIGHMEM is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_SPLIT_PTLOCK_CPUS=4096 +# CONFIG_PHYS_ADDR_T_64BIT is not set +CONFIG_ZONE_DMA_FLAG=0 +CONFIG_VIRT_TO_BUS=y +CONFIG_HAVE_MLOCK=y +CONFIG_HAVE_MLOCKED_PAGE_BIT=y +# CONFIG_KSM is not set +CONFIG_DEFAULT_MMAP_MIN_ADDR=4096 +CONFIG_ALIGNMENT_TRAP=y +# CONFIG_UACCESS_WITH_MEMCPY is not set + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CMDLINE="root=31:02 rootfstype=jffs2 ro console=ttyS0,115200" +# CONFIG_XIP_KERNEL is not set +# CONFIG_KEXEC is not set + +# +# CPU Power Management +# +CONFIG_CPU_FREQ=y +CONFIG_CPU_FREQ_TABLE=y +# CONFIG_CPU_FREQ_DEBUG is not set +CONFIG_CPU_FREQ_STAT=y +# CONFIG_CPU_FREQ_STAT_DETAILS is not set +CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y +# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set +# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set +# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set +# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set +CONFIG_CPU_FREQ_GOV_PERFORMANCE=y +CONFIG_CPU_FREQ_GOV_POWERSAVE=m +CONFIG_CPU_FREQ_GOV_USERSPACE=m +CONFIG_CPU_FREQ_GOV_ONDEMAND=m +CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m +# CONFIG_CPU_IDLE is not set + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +CONFIG_FPE_NWFPE=y +# CONFIG_FPE_NWFPE_XP is not set +# CONFIG_FPE_FASTFPE is not set + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set +CONFIG_HAVE_AOUT=y +# CONFIG_BINFMT_AOUT is not set +# CONFIG_BINFMT_MISC is not set + +# +# Power management options +# +CONFIG_PM=y +# CONFIG_PM_DEBUG is not set +CONFIG_PM_SLEEP=y +CONFIG_SUSPEND=y +CONFIG_SUSPEND_FREEZER=y +CONFIG_APM_EMULATION=y +# CONFIG_PM_RUNTIME is not set +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +CONFIG_XFRM=y +# CONFIG_XFRM_USER is not set +# CONFIG_XFRM_SUB_POLICY is not set +# CONFIG_XFRM_MIGRATE is not set +# CONFIG_XFRM_STATISTICS is not set +# CONFIG_NET_KEY is not set +CONFIG_INET=y +# CONFIG_IP_MULTICAST is not set +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +# CONFIG_IP_PNP_BOOTP is not set +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_ARPD is not set +CONFIG_SYN_COOKIES=y +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_XFRM_MODE_TRANSPORT=y +CONFIG_INET_XFRM_MODE_TUNNEL=y +CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IPV6 is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set +# CONFIG_IP_DCCP is not set +# CONFIG_IP_SCTP is not set +# CONFIG_RDS is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set +# CONFIG_PHONET is not set +# CONFIG_IEEE802154 is not set +# CONFIG_NET_SCHED is not set +# CONFIG_DCB is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set +# CONFIG_IRDA is not set +CONFIG_BT=m +CONFIG_BT_L2CAP=m +# CONFIG_BT_SCO is not set +CONFIG_BT_RFCOMM=m +CONFIG_BT_RFCOMM_TTY=y +CONFIG_BT_BNEP=m +# CONFIG_BT_BNEP_MC_FILTER is not set +# CONFIG_BT_BNEP_PROTO_FILTER is not set +# CONFIG_BT_HIDP is not set + +# +# Bluetooth device drivers +# +# CONFIG_BT_HCIBTUSB is not set +# CONFIG_BT_HCIBTSDIO is not set +CONFIG_BT_HCIUART=m +CONFIG_BT_HCIUART_H4=y +CONFIG_BT_HCIUART_BCSP=y +# CONFIG_BT_HCIUART_LL is not set +# CONFIG_BT_HCIBCM203X is not set +# CONFIG_BT_HCIBPA10X is not set +# CONFIG_BT_HCIBFUSB is not set +# CONFIG_BT_HCIDTL1 is not set +# CONFIG_BT_HCIBT3C is not set +# CONFIG_BT_HCIBLUECARD is not set +# CONFIG_BT_HCIBTUART is not set +# CONFIG_BT_HCIVHCI is not set +# CONFIG_BT_MRVL is not set +# CONFIG_AF_RXRPC is not set +CONFIG_WIRELESS=y +CONFIG_WIRELESS_EXT=y +CONFIG_WEXT_CORE=y +CONFIG_WEXT_PROC=y +CONFIG_WEXT_SPY=y +CONFIG_WEXT_PRIV=y +CONFIG_CFG80211=m +# CONFIG_NL80211_TESTMODE is not set +# CONFIG_CFG80211_DEVELOPER_WARNINGS is not set +# CONFIG_CFG80211_REG_DEBUG is not set +CONFIG_CFG80211_DEFAULT_PS=y +# CONFIG_WIRELESS_OLD_REGULATORY is not set +CONFIG_CFG80211_WEXT=y +CONFIG_WIRELESS_EXT_SYSFS=y +CONFIG_LIB80211=m +# CONFIG_LIB80211_DEBUG is not set +CONFIG_MAC80211=m +CONFIG_MAC80211_RC_MINSTREL=y +# CONFIG_MAC80211_RC_DEFAULT_PID is not set +CONFIG_MAC80211_RC_DEFAULT_MINSTREL=y +CONFIG_MAC80211_RC_DEFAULT="minstrel" +# CONFIG_MAC80211_MESH is not set +# CONFIG_MAC80211_LEDS is not set +# CONFIG_MAC80211_DEBUG_MENU is not set +# CONFIG_WIMAX is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +# CONFIG_DEVTMPFS is not set +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +CONFIG_FW_LOADER=y +CONFIG_FIRMWARE_IN_KERNEL=y +CONFIG_EXTRA_FIRMWARE="" +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set +# CONFIG_CONNECTOR is not set +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_TESTS is not set +# CONFIG_MTD_CONCAT is not set +CONFIG_MTD_PARTITIONS=y +CONFIG_MTD_REDBOOT_PARTS=y +CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1 +# CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set +CONFIG_MTD_REDBOOT_PARTS_READONLY=y +# CONFIG_MTD_CMDLINE_PARTS is not set +# CONFIG_MTD_AFS_PARTS is not set +# CONFIG_MTD_AR7_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=m +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=y +CONFIG_MTD_JEDECPROBE=y +CONFIG_MTD_GEN_PROBE=y +CONFIG_MTD_CFI_ADV_OPTIONS=y +CONFIG_MTD_CFI_NOSWAP=y +# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set +# CONFIG_MTD_CFI_LE_BYTE_SWAP is not set +CONFIG_MTD_CFI_GEOMETRY=y +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +# CONFIG_MTD_MAP_BANK_WIDTH_4 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +# CONFIG_MTD_CFI_I2 is not set +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_OTP is not set +CONFIG_MTD_CFI_INTELEXT=y +CONFIG_MTD_CFI_AMDSTD=y +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=y +CONFIG_MTD_RAM=y +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set +# CONFIG_MTD_XIP is not set + +# +# Mapping drivers for chip access +# +CONFIG_MTD_COMPLEX_MAPPINGS=y +CONFIG_MTD_PHYSMAP=y +# CONFIG_MTD_PHYSMAP_COMPAT is not set +CONFIG_MTD_PXA2XX=y +# CONFIG_MTD_ARM_INTEGRATOR is not set +# CONFIG_MTD_IMPA7 is not set +# CONFIG_MTD_GPIO_ADDR is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_DATAFLASH is not set +# CONFIG_MTD_M25P80 is not set +# CONFIG_MTD_SST25L is not set +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +# CONFIG_MTD_NAND is not set +# CONFIG_MTD_ONENAND is not set + +# +# LPDDR flash memory drivers +# +# CONFIG_MTD_LPDDR is not set + +# +# UBI - Unsorted block images +# +# CONFIG_MTD_UBI is not set +# CONFIG_PARPORT is not set +# CONFIG_PNP is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=m +# CONFIG_BLK_DEV_CRYPTOLOOP is not set + +# +# DRBD disabled because PROC_FS, INET or CONNECTOR not selected +# +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_UB is not set +# CONFIG_BLK_DEV_RAM is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +# CONFIG_MG_DISK is not set +CONFIG_MISC_DEVICES=y +# CONFIG_ICS932S401 is not set +# CONFIG_ENCLOSURE_SERVICES is not set +# CONFIG_ISL29003 is not set +# CONFIG_DS1682 is not set +# CONFIG_C2PORT is not set + +# +# EEPROM support +# +CONFIG_EEPROM_AT24=m +# CONFIG_EEPROM_AT25 is not set +# CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_MAX6875 is not set +# CONFIG_EEPROM_93CX6 is not set +# CONFIG_IWMC3200TOP is not set +CONFIG_HAVE_IDE=y +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=m +CONFIG_SCSI_DMA=y +# CONFIG_SCSI_TGT is not set +# CONFIG_SCSI_NETLINK is not set +# CONFIG_SCSI_PROC_FS is not set + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=m +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +# CONFIG_BLK_DEV_SR is not set +# CONFIG_CHR_DEV_SG is not set +# CONFIG_CHR_DEV_SCH is not set +# CONFIG_SCSI_MULTI_LUN is not set +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set +CONFIG_SCSI_WAIT_SCAN=m + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set +CONFIG_SCSI_LOWLEVEL=y +# CONFIG_ISCSI_TCP is not set +# CONFIG_SCSI_AHA152X is not set +# CONFIG_SCSI_AIC7XXX_OLD is not set +# CONFIG_SCSI_ADVANSYS is not set +# CONFIG_SCSI_IN2000 is not set +# CONFIG_LIBFC is not set +# CONFIG_LIBFCOE is not set +# CONFIG_SCSI_DTC3280 is not set +# CONFIG_SCSI_FUTURE_DOMAIN is not set +# CONFIG_SCSI_GENERIC_NCR5380 is not set +# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set +# CONFIG_SCSI_NCR53C406A is not set +# CONFIG_SCSI_PAS16 is not set +# CONFIG_SCSI_QLOGIC_FAS is not set +# CONFIG_SCSI_SYM53C416 is not set +# CONFIG_SCSI_T128 is not set +# CONFIG_SCSI_DEBUG is not set +# CONFIG_SCSI_LOWLEVEL_PCMCIA is not set +# CONFIG_SCSI_DH is not set +# CONFIG_SCSI_OSD_INITIATOR is not set +CONFIG_ATA=m +# CONFIG_ATA_NONSTANDARD is not set +CONFIG_ATA_VERBOSE_ERROR=y +# CONFIG_SATA_PMP is not set +CONFIG_ATA_SFF=y +# CONFIG_SATA_MV is not set +# CONFIG_PATA_LEGACY is not set +CONFIG_PATA_PCMCIA=m +# CONFIG_PATA_QDI is not set +# CONFIG_PATA_WINBOND_VLB is not set +# CONFIG_MD is not set +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_ARCNET is not set +# CONFIG_PHYLIB is not set +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_AX88796 is not set +# CONFIG_NET_VENDOR_3COM is not set +# CONFIG_NET_VENDOR_SMC is not set +# CONFIG_SMC91X is not set +CONFIG_DM9000=y +CONFIG_DM9000_DEBUGLEVEL=4 +# CONFIG_DM9000_FORCE_SIMPLE_PHY_POLL is not set +# CONFIG_ENC28J60 is not set +# CONFIG_ETHOC is not set +# CONFIG_SMC911X is not set +# CONFIG_SMSC911X is not set +# CONFIG_NET_VENDOR_RACAL is not set +# CONFIG_DNET is not set +# CONFIG_AT1700 is not set +# CONFIG_DEPCA is not set +# CONFIG_HP100 is not set +# CONFIG_NET_ISA is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set +# CONFIG_NET_PCI is not set +# CONFIG_B44 is not set +# CONFIG_CS89x0 is not set +# CONFIG_KS8842 is not set +# CONFIG_KS8851 is not set +# CONFIG_KS8851_MLL is not set +# CONFIG_NETDEV_1000 is not set +# CONFIG_NETDEV_10000 is not set +# CONFIG_TR is not set +CONFIG_WLAN=y +# CONFIG_PCMCIA_RAYCS is not set +# CONFIG_LIBERTAS_THINFIRM is not set +# CONFIG_ATMEL is not set +# CONFIG_AT76C50X_USB is not set +# CONFIG_AIRO_CS is not set +# CONFIG_PCMCIA_WL3501 is not set +# CONFIG_USB_ZD1201 is not set +# CONFIG_USB_NET_RNDIS_WLAN is not set +# CONFIG_RTL8187 is not set +# CONFIG_MAC80211_HWSIM is not set +# CONFIG_ATH_COMMON is not set +# CONFIG_B43 is not set +# CONFIG_B43LEGACY is not set +# CONFIG_HOSTAP is not set +# CONFIG_IWM is not set +# CONFIG_LIBERTAS is not set +CONFIG_HERMES=m +CONFIG_HERMES_CACHE_FW_ON_INIT=y +CONFIG_PCMCIA_HERMES=m +# CONFIG_PCMCIA_SPECTRUM is not set +# CONFIG_P54_COMMON is not set +CONFIG_RT2X00=m +# CONFIG_RT2500USB is not set +CONFIG_RT73USB=m +# CONFIG_RT2800USB is not set +CONFIG_RT2X00_LIB_USB=m +CONFIG_RT2X00_LIB=m +CONFIG_RT2X00_LIB_FIRMWARE=y +CONFIG_RT2X00_LIB_CRYPTO=y +CONFIG_RT2X00_LIB_LEDS=y +# CONFIG_RT2X00_DEBUG is not set +# CONFIG_WL12XX is not set +# CONFIG_ZD1211RW is not set + +# +# Enable WiMAX (Networking options) to see the WiMAX drivers +# + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set +CONFIG_NET_PCMCIA=y +# CONFIG_PCMCIA_3C589 is not set +# CONFIG_PCMCIA_3C574 is not set +# CONFIG_PCMCIA_FMVJ18X is not set +# CONFIG_PCMCIA_PCNET is not set +# CONFIG_PCMCIA_NMCLAN is not set +# CONFIG_PCMCIA_SMC91C92 is not set +# CONFIG_PCMCIA_XIRC2PS is not set +# CONFIG_PCMCIA_AXNET is not set +# CONFIG_WAN is not set +CONFIG_PPP=m +# CONFIG_PPP_MULTILINK is not set +# CONFIG_PPP_FILTER is not set +CONFIG_PPP_ASYNC=m +# CONFIG_PPP_SYNC_TTY is not set +CONFIG_PPP_DEFLATE=m +CONFIG_PPP_BSDCOMP=m +# CONFIG_PPP_MPPE is not set +# CONFIG_PPPOE is not set +# CONFIG_PPPOL2TP is not set +# CONFIG_SLIP is not set +CONFIG_SLHC=m +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_ISDN is not set +# CONFIG_PHONE is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=y +# CONFIG_INPUT_MOUSEDEV_PSAUX is not set +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +CONFIG_INPUT_EVDEV=m +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +CONFIG_INPUT_TOUCHSCREEN=y +# CONFIG_TOUCHSCREEN_ADS7846 is not set +# CONFIG_TOUCHSCREEN_AD7877 is not set +# CONFIG_TOUCHSCREEN_AD7879_I2C is not set +# CONFIG_TOUCHSCREEN_AD7879_SPI is not set +# CONFIG_TOUCHSCREEN_AD7879 is not set +# CONFIG_TOUCHSCREEN_EETI is not set +CONFIG_TOUCHSCREEN_FUJITSU=m +# CONFIG_TOUCHSCREEN_GUNZE is not set +CONFIG_TOUCHSCREEN_ELO=m +# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set +# CONFIG_TOUCHSCREEN_MCS5000 is not set +CONFIG_TOUCHSCREEN_MTOUCH=m +CONFIG_TOUCHSCREEN_INEXIO=m +# CONFIG_TOUCHSCREEN_MK712 is not set +CONFIG_TOUCHSCREEN_HTCPEN=m +CONFIG_TOUCHSCREEN_PENMOUNT=m +CONFIG_TOUCHSCREEN_TOUCHRIGHT=m +CONFIG_TOUCHSCREEN_TOUCHWIN=m +# CONFIG_TOUCHSCREEN_WM97XX is not set +# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set +CONFIG_TOUCHSCREEN_TOUCHIT213=m +# CONFIG_TOUCHSCREEN_TSC2007 is not set +# CONFIG_TOUCHSCREEN_W90X900 is not set +CONFIG_INPUT_MISC=y +# CONFIG_INPUT_ATI_REMOTE is not set +# CONFIG_INPUT_ATI_REMOTE2 is not set +# CONFIG_INPUT_KEYSPAN_REMOTE is not set +# CONFIG_INPUT_POWERMATE is not set +# CONFIG_INPUT_YEALINK is not set +# CONFIG_INPUT_CM109 is not set +CONFIG_INPUT_UINPUT=m +# CONFIG_INPUT_GPIO_ROTARY_ENCODER is not set + +# +# Hardware I/O ports +# +CONFIG_SERIO=y +CONFIG_SERIO_SERPORT=y +# CONFIG_SERIO_RAW is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_CONSOLE_TRANSLATIONS=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +CONFIG_DEVKMEM=y +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +# CONFIG_SERIAL_8250_CS is not set +CONFIG_SERIAL_8250_NR_UARTS=7 +CONFIG_SERIAL_8250_RUNTIME_UARTS=7 +# CONFIG_SERIAL_8250_EXTENDED is not set + +# +# Non-8250 serial port support +# +# CONFIG_SERIAL_MAX3100 is not set +# CONFIG_SERIAL_PXA is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set +# CONFIG_LEGACY_PTYS is not set +# CONFIG_IPMI_HANDLER is not set +CONFIG_HW_RANDOM=m +# CONFIG_HW_RANDOM_TIMERIOMEM is not set +# CONFIG_DTLK is not set +# CONFIG_R3964 is not set + +# +# PCMCIA character devices +# +# CONFIG_SYNCLINK_CS is not set +# CONFIG_CARDMAN_4000 is not set +# CONFIG_CARDMAN_4040 is not set +# CONFIG_IPWIRELESS is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +CONFIG_DEVPORT=y +CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_COMPAT=y +CONFIG_I2C_CHARDEV=y +# CONFIG_I2C_HELPER_AUTO is not set + +# +# I2C Algorithms +# +CONFIG_I2C_ALGOBIT=y +# CONFIG_I2C_ALGOPCF is not set +# CONFIG_I2C_ALGOPCA is not set + +# +# I2C Hardware Bus support +# + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# +# CONFIG_I2C_DESIGNWARE is not set +CONFIG_I2C_GPIO=y +# CONFIG_I2C_OCORES is not set +CONFIG_I2C_PXA=y +# CONFIG_I2C_PXA_SLAVE is not set +# CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_TAOS_EVM is not set +# CONFIG_I2C_TINY_USB is not set + +# +# Other I2C/SMBus bus drivers +# +# CONFIG_I2C_ELEKTOR is not set +# CONFIG_I2C_PCA_ISA is not set +# CONFIG_I2C_PCA_PLATFORM is not set +# CONFIG_I2C_STUB is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_SENSORS_TSL2550 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set +CONFIG_SPI=y +# CONFIG_SPI_DEBUG is not set +CONFIG_SPI_MASTER=y + +# +# SPI Master Controller Drivers +# +# CONFIG_SPI_BITBANG is not set +# CONFIG_SPI_GPIO is not set +CONFIG_SPI_PXA2XX=y + +# +# SPI Protocol Masters +# +# CONFIG_SPI_SPIDEV is not set +# CONFIG_SPI_TLE62X0 is not set + +# +# PPS support +# +# CONFIG_PPS is not set +CONFIG_ARCH_REQUIRE_GPIOLIB=y +CONFIG_GPIOLIB=y +# CONFIG_DEBUG_GPIO is not set +CONFIG_GPIO_SYSFS=y + +# +# Memory mapped GPIO expanders: +# + +# +# I2C GPIO expanders: +# +# CONFIG_GPIO_MAX732X is not set +CONFIG_GPIO_PCA953X=y +# CONFIG_GPIO_PCF857X is not set + +# +# PCI GPIO expanders: +# + +# +# SPI GPIO expanders: +# +# CONFIG_GPIO_MAX7301 is not set +# CONFIG_GPIO_MCP23S08 is not set +# CONFIG_GPIO_MC33880 is not set + +# +# AC97 GPIO expanders: +# +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +CONFIG_HWMON=y +# CONFIG_HWMON_VID is not set +# CONFIG_HWMON_DEBUG_CHIP is not set + +# +# Native drivers +# +# CONFIG_SENSORS_AD7414 is not set +# CONFIG_SENSORS_AD7418 is not set +# CONFIG_SENSORS_ADCXX is not set +# CONFIG_SENSORS_ADM1021 is not set +# CONFIG_SENSORS_ADM1025 is not set +# CONFIG_SENSORS_ADM1026 is not set +# CONFIG_SENSORS_ADM1029 is not set +# CONFIG_SENSORS_ADM1031 is not set +# CONFIG_SENSORS_ADM9240 is not set +# CONFIG_SENSORS_ADT7462 is not set +# CONFIG_SENSORS_ADT7470 is not set +# CONFIG_SENSORS_ADT7473 is not set +# CONFIG_SENSORS_ADT7475 is not set +# CONFIG_SENSORS_ATXP1 is not set +# CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_F71805F is not set +# CONFIG_SENSORS_F71882FG is not set +# CONFIG_SENSORS_F75375S is not set +# CONFIG_SENSORS_G760A is not set +# CONFIG_SENSORS_GL518SM is not set +# CONFIG_SENSORS_GL520SM is not set +# CONFIG_SENSORS_IT87 is not set +# CONFIG_SENSORS_LM63 is not set +# CONFIG_SENSORS_LM70 is not set +CONFIG_SENSORS_LM75=m +# CONFIG_SENSORS_LM77 is not set +# CONFIG_SENSORS_LM78 is not set +# CONFIG_SENSORS_LM80 is not set +# CONFIG_SENSORS_LM83 is not set +# CONFIG_SENSORS_LM85 is not set +# CONFIG_SENSORS_LM87 is not set +# CONFIG_SENSORS_LM90 is not set +# CONFIG_SENSORS_LM92 is not set +# CONFIG_SENSORS_LM93 is not set +# CONFIG_SENSORS_LTC4215 is not set +# CONFIG_SENSORS_LTC4245 is not set +# CONFIG_SENSORS_LM95241 is not set +# CONFIG_SENSORS_MAX1111 is not set +# CONFIG_SENSORS_MAX1619 is not set +# CONFIG_SENSORS_MAX6650 is not set +# CONFIG_SENSORS_PC87360 is not set +# CONFIG_SENSORS_PC87427 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_SENSORS_SHT15 is not set +# CONFIG_SENSORS_DME1737 is not set +# CONFIG_SENSORS_SMSC47M1 is not set +# CONFIG_SENSORS_SMSC47M192 is not set +# CONFIG_SENSORS_SMSC47B397 is not set +# CONFIG_SENSORS_ADS7828 is not set +# CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_TMP401 is not set +# CONFIG_SENSORS_TMP421 is not set +# CONFIG_SENSORS_VT1211 is not set +# CONFIG_SENSORS_W83781D is not set +# CONFIG_SENSORS_W83791D is not set +# CONFIG_SENSORS_W83792D is not set +# CONFIG_SENSORS_W83793 is not set +# CONFIG_SENSORS_W83L785TS is not set +# CONFIG_SENSORS_W83L786NG is not set +# CONFIG_SENSORS_W83627HF is not set +# CONFIG_SENSORS_W83627EHF is not set +# CONFIG_SENSORS_LIS3_SPI is not set +# CONFIG_THERMAL is not set +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +# CONFIG_SA1100_WATCHDOG is not set + +# +# ISA-based Watchdog Cards +# +# CONFIG_PCWATCHDOG is not set +# CONFIG_MIXCOMWD is not set +# CONFIG_WDT is not set + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set +CONFIG_SSB_POSSIBLE=y + +# +# Sonics Silicon Backplane +# +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_CORE is not set +# CONFIG_MFD_SM501 is not set +# CONFIG_MFD_ASIC3 is not set +# CONFIG_HTC_EGPIO is not set +# CONFIG_HTC_PASIC3 is not set +# CONFIG_UCB1400_CORE is not set +# CONFIG_TPS65010 is not set +# CONFIG_TWL4030_CORE is not set +# CONFIG_MFD_TMIO is not set +# CONFIG_MFD_T7L66XB is not set +# CONFIG_MFD_TC6387XB is not set +# CONFIG_MFD_TC6393XB is not set +# CONFIG_PMIC_DA903X is not set +# CONFIG_MFD_WM8400 is not set +# CONFIG_MFD_WM831X is not set +# CONFIG_MFD_WM8350_I2C is not set +# CONFIG_MFD_PCF50633 is not set +# CONFIG_MFD_MC13783 is not set +# CONFIG_AB3100_CORE is not set +# CONFIG_EZX_PCAP is not set +# CONFIG_REGULATOR is not set +# CONFIG_MEDIA_SUPPORT is not set + +# +# Graphics support +# +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +CONFIG_FB=y +# CONFIG_FIRMWARE_EDID is not set +# CONFIG_FB_DDC is not set +# CONFIG_FB_BOOT_VESA_SUPPORT is not set +CONFIG_FB_CFB_FILLRECT=m +CONFIG_FB_CFB_COPYAREA=m +CONFIG_FB_CFB_IMAGEBLIT=m +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set +# CONFIG_FB_SYS_FILLRECT is not set +# CONFIG_FB_SYS_COPYAREA is not set +# CONFIG_FB_SYS_IMAGEBLIT is not set +# CONFIG_FB_FOREIGN_ENDIAN is not set +# CONFIG_FB_SYS_FOPS is not set +# CONFIG_FB_SVGALIB is not set +# CONFIG_FB_MACMODES is not set +# CONFIG_FB_BACKLIGHT is not set +# CONFIG_FB_MODE_HELPERS is not set +# CONFIG_FB_TILEBLITTING is not set + +# +# Frame buffer hardware drivers +# +# CONFIG_FB_S1D13XXX is not set +CONFIG_FB_PXA=m +# CONFIG_FB_PXA_OVERLAY is not set +# CONFIG_FB_PXA_SMARTPANEL is not set +CONFIG_FB_PXA_PARAMETERS=y +# CONFIG_FB_MBX is not set +# CONFIG_FB_W100 is not set +# CONFIG_FB_VIRTUAL is not set +# CONFIG_FB_METRONOME is not set +# CONFIG_FB_MB862XX is not set +# CONFIG_FB_BROADSHEET is not set +CONFIG_BACKLIGHT_LCD_SUPPORT=y +CONFIG_LCD_CLASS_DEVICE=m +# CONFIG_LCD_LMS283GF05 is not set +# CONFIG_LCD_LTV350QV is not set +# CONFIG_LCD_ILI9320 is not set +# CONFIG_LCD_TDO24M is not set +# CONFIG_LCD_VGG2432A4 is not set +# CONFIG_LCD_PLATFORM is not set +CONFIG_BACKLIGHT_CLASS_DEVICE=m +CONFIG_BACKLIGHT_GENERIC=m + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +# CONFIG_MDA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y +CONFIG_FRAMEBUFFER_CONSOLE=m +# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set +# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set +# CONFIG_FONTS is not set +CONFIG_FONT_8x8=y +CONFIG_FONT_8x16=y +CONFIG_LOGO=y +CONFIG_LOGO_LINUX_MONO=y +CONFIG_LOGO_LINUX_VGA16=y +CONFIG_LOGO_LINUX_CLUT224=y +CONFIG_SOUND=m +CONFIG_SOUND_OSS_CORE=y +CONFIG_SOUND_OSS_CORE_PRECLAIM=y +CONFIG_SND=m +CONFIG_SND_TIMER=m +CONFIG_SND_PCM=m +CONFIG_SND_JACK=y +# CONFIG_SND_SEQUENCER is not set +CONFIG_SND_OSSEMUL=y +CONFIG_SND_MIXER_OSS=m +CONFIG_SND_PCM_OSS=m +CONFIG_SND_PCM_OSS_PLUGINS=y +# CONFIG_SND_DYNAMIC_MINORS is not set +# CONFIG_SND_SUPPORT_OLD_API is not set +CONFIG_SND_VERBOSE_PROCFS=y +# CONFIG_SND_VERBOSE_PRINTK is not set +# CONFIG_SND_DEBUG is not set +CONFIG_SND_VMASTER=y +# CONFIG_SND_RAWMIDI_SEQ is not set +# CONFIG_SND_OPL3_LIB_SEQ is not set +# CONFIG_SND_OPL4_LIB_SEQ is not set +# CONFIG_SND_SBAWE_SEQ is not set +# CONFIG_SND_EMU10K1_SEQ is not set +CONFIG_SND_AC97_CODEC=m +CONFIG_SND_DRIVERS=y +# CONFIG_SND_DUMMY is not set +# CONFIG_SND_MTPAV is not set +# CONFIG_SND_SERIAL_U16550 is not set +# CONFIG_SND_MPU401 is not set +# CONFIG_SND_AC97_POWER_SAVE is not set +CONFIG_SND_ARM=y +CONFIG_SND_PXA2XX_PCM=m +CONFIG_SND_PXA2XX_LIB=m +CONFIG_SND_PXA2XX_LIB_AC97=y +CONFIG_SND_PXA2XX_AC97=m +# CONFIG_SND_SPI is not set +CONFIG_SND_USB=y +# CONFIG_SND_USB_AUDIO is not set +# CONFIG_SND_USB_CAIAQ is not set +# CONFIG_SND_PCMCIA is not set +CONFIG_SND_SOC=m +CONFIG_SND_PXA2XX_SOC=m +CONFIG_SND_SOC_I2C_AND_SPI=m +# CONFIG_SND_SOC_ALL_CODECS is not set +# CONFIG_SOUND_PRIME is not set +CONFIG_AC97_BUS=m +# CONFIG_HID_SUPPORT is not set +CONFIG_USB_SUPPORT=y +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y +# CONFIG_USB_ARCH_HAS_EHCI is not set +CONFIG_USB=m +# CONFIG_USB_DEBUG is not set +# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set + +# +# Miscellaneous USB options +# +CONFIG_USB_DEVICEFS=y +CONFIG_USB_DEVICE_CLASS=y +# CONFIG_USB_DYNAMIC_MINORS is not set +CONFIG_USB_SUSPEND=y +# CONFIG_USB_OTG is not set +# CONFIG_USB_MON is not set +# CONFIG_USB_WUSB is not set +# CONFIG_USB_WUSB_CBAF is not set + +# +# USB Host Controller Drivers +# +# CONFIG_USB_C67X00_HCD is not set +# CONFIG_USB_OXU210HP_HCD is not set +# CONFIG_USB_ISP116X_HCD is not set +# CONFIG_USB_ISP1760_HCD is not set +# CONFIG_USB_ISP1362_HCD is not set +CONFIG_USB_OHCI_HCD=m +# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set +# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set +CONFIG_USB_OHCI_LITTLE_ENDIAN=y +# CONFIG_USB_SL811_HCD is not set +# CONFIG_USB_R8A66597_HCD is not set +# CONFIG_USB_HWA_HCD is not set +# CONFIG_USB_MUSB_HDRC is not set +# CONFIG_USB_GADGET_MUSB_HDRC is not set + +# +# USB Device Class drivers +# +CONFIG_USB_ACM=m +# CONFIG_USB_PRINTER is not set +# CONFIG_USB_WDM is not set +# CONFIG_USB_TMC is not set + +# +# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may +# + +# +# also be needed; see USB_STORAGE Help for more info +# +CONFIG_USB_STORAGE=m +# CONFIG_USB_STORAGE_DEBUG is not set +# CONFIG_USB_STORAGE_DATAFAB is not set +# CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set +# CONFIG_USB_STORAGE_USBAT is not set +# CONFIG_USB_STORAGE_SDDR09 is not set +# CONFIG_USB_STORAGE_SDDR55 is not set +# CONFIG_USB_STORAGE_JUMPSHOT is not set +# CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_ONETOUCH is not set +# CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set +# CONFIG_USB_LIBUSUAL is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set + +# +# USB port drivers +# +CONFIG_USB_SERIAL=m +# CONFIG_USB_EZUSB is not set +CONFIG_USB_SERIAL_GENERIC=y +# CONFIG_USB_SERIAL_AIRCABLE is not set +# CONFIG_USB_SERIAL_ARK3116 is not set +# CONFIG_USB_SERIAL_BELKIN is not set +# CONFIG_USB_SERIAL_CH341 is not set +# CONFIG_USB_SERIAL_WHITEHEAT is not set +# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set +# CONFIG_USB_SERIAL_CP210X is not set +# CONFIG_USB_SERIAL_CYPRESS_M8 is not set +# CONFIG_USB_SERIAL_EMPEG is not set +# CONFIG_USB_SERIAL_FTDI_SIO is not set +# CONFIG_USB_SERIAL_FUNSOFT is not set +# CONFIG_USB_SERIAL_VISOR is not set +# CONFIG_USB_SERIAL_IPAQ is not set +# CONFIG_USB_SERIAL_IR is not set +# CONFIG_USB_SERIAL_EDGEPORT is not set +# CONFIG_USB_SERIAL_EDGEPORT_TI is not set +# CONFIG_USB_SERIAL_GARMIN is not set +# CONFIG_USB_SERIAL_IPW is not set +# CONFIG_USB_SERIAL_IUU is not set +# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set +# CONFIG_USB_SERIAL_KEYSPAN is not set +# CONFIG_USB_SERIAL_KLSI is not set +# CONFIG_USB_SERIAL_KOBIL_SCT is not set +CONFIG_USB_SERIAL_MCT_U232=m +# CONFIG_USB_SERIAL_MOS7720 is not set +# CONFIG_USB_SERIAL_MOS7840 is not set +# CONFIG_USB_SERIAL_MOTOROLA is not set +# CONFIG_USB_SERIAL_NAVMAN is not set +# CONFIG_USB_SERIAL_PL2303 is not set +# CONFIG_USB_SERIAL_OTI6858 is not set +# CONFIG_USB_SERIAL_QUALCOMM is not set +# CONFIG_USB_SERIAL_SPCP8X5 is not set +# CONFIG_USB_SERIAL_HP4X is not set +# CONFIG_USB_SERIAL_SAFE is not set +# CONFIG_USB_SERIAL_SIEMENS_MPI is not set +# CONFIG_USB_SERIAL_SIERRAWIRELESS is not set +# CONFIG_USB_SERIAL_SYMBOL is not set +# CONFIG_USB_SERIAL_TI is not set +# CONFIG_USB_SERIAL_CYBERJACK is not set +# CONFIG_USB_SERIAL_XIRCOM is not set +# CONFIG_USB_SERIAL_OPTION is not set +# CONFIG_USB_SERIAL_OMNINET is not set +# CONFIG_USB_SERIAL_OPTICON is not set +# CONFIG_USB_SERIAL_DEBUG is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_ADUTUX is not set +# CONFIG_USB_SEVSEG is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_BERRY_CHARGE is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYPRESS_CY7C63 is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_FTDI_ELAN is not set +# CONFIG_USB_APPLEDISPLAY is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TRANCEVIBRATOR is not set +# CONFIG_USB_IOWARRIOR is not set +# CONFIG_USB_TEST is not set +# CONFIG_USB_ISIGHTFW is not set +# CONFIG_USB_VST is not set +CONFIG_USB_GADGET=m +# CONFIG_USB_GADGET_DEBUG is not set +# CONFIG_USB_GADGET_DEBUG_FILES is not set +CONFIG_USB_GADGET_VBUS_DRAW=2 +CONFIG_USB_GADGET_SELECTED=y +# CONFIG_USB_GADGET_AT91 is not set +# CONFIG_USB_GADGET_ATMEL_USBA is not set +# CONFIG_USB_GADGET_FSL_USB2 is not set +# CONFIG_USB_GADGET_LH7A40X is not set +# CONFIG_USB_GADGET_OMAP is not set +# CONFIG_USB_GADGET_PXA25X is not set +# CONFIG_USB_GADGET_R8A66597 is not set +CONFIG_USB_GADGET_PXA27X=y +CONFIG_USB_PXA27X=m +# CONFIG_USB_GADGET_S3C_HSOTG is not set +# CONFIG_USB_GADGET_IMX is not set +# CONFIG_USB_GADGET_S3C2410 is not set +# CONFIG_USB_GADGET_M66592 is not set +# CONFIG_USB_GADGET_AMD5536UDC is not set +# CONFIG_USB_GADGET_FSL_QE is not set +# CONFIG_USB_GADGET_CI13XXX is not set +# CONFIG_USB_GADGET_NET2280 is not set +# CONFIG_USB_GADGET_GOKU is not set +# CONFIG_USB_GADGET_LANGWELL is not set +# CONFIG_USB_GADGET_DUMMY_HCD is not set +# CONFIG_USB_GADGET_DUALSPEED is not set +# CONFIG_USB_ZERO is not set +# CONFIG_USB_AUDIO is not set +CONFIG_USB_ETH=m +CONFIG_USB_ETH_RNDIS=y +# CONFIG_USB_ETH_EEM is not set +CONFIG_USB_GADGETFS=m +CONFIG_USB_FILE_STORAGE=m +# CONFIG_USB_FILE_STORAGE_TEST is not set +CONFIG_USB_G_SERIAL=m +# CONFIG_USB_MIDI_GADGET is not set +CONFIG_USB_G_PRINTER=m +# CONFIG_USB_CDC_COMPOSITE is not set + +# +# OTG and related infrastructure +# +CONFIG_USB_OTG_UTILS=y +# CONFIG_USB_GPIO_VBUS is not set +# CONFIG_NOP_USB_XCEIV is not set +CONFIG_MMC=y +# CONFIG_MMC_DEBUG is not set +# CONFIG_MMC_UNSAFE_RESUME is not set + +# +# MMC/SD/SDIO Card Drivers +# +CONFIG_MMC_BLOCK=y +# CONFIG_MMC_BLOCK_BOUNCE is not set +# CONFIG_SDIO_UART is not set +# CONFIG_MMC_TEST is not set + +# +# MMC/SD/SDIO Host Controller Drivers +# +CONFIG_MMC_PXA=y +# CONFIG_MMC_SDHCI is not set +# CONFIG_MMC_AT91 is not set +# CONFIG_MMC_ATMELMCI is not set +# CONFIG_MMC_SPI is not set +# CONFIG_MEMSTICK is not set +CONFIG_NEW_LEDS=y +CONFIG_LEDS_CLASS=m + +# +# LED drivers +# +# CONFIG_LEDS_PCA9532 is not set +CONFIG_LEDS_GPIO=m +CONFIG_LEDS_GPIO_PLATFORM=y +# CONFIG_LEDS_LP3944 is not set +# CONFIG_LEDS_PCA955X is not set +# CONFIG_LEDS_DAC124S085 is not set +# CONFIG_LEDS_BD2802 is not set + +# +# LED Triggers +# +CONFIG_LEDS_TRIGGERS=y +CONFIG_LEDS_TRIGGER_TIMER=m +CONFIG_LEDS_TRIGGER_HEARTBEAT=m +CONFIG_LEDS_TRIGGER_BACKLIGHT=m +CONFIG_LEDS_TRIGGER_GPIO=m +CONFIG_LEDS_TRIGGER_DEFAULT_ON=m + +# +# iptables trigger is under Netfilter config (LED target) +# +# CONFIG_ACCESSIBILITY is not set +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=m + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y +# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set +# CONFIG_RTC_DRV_TEST is not set + +# +# I2C RTC drivers +# +# CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1374 is not set +# CONFIG_RTC_DRV_DS1672 is not set +# CONFIG_RTC_DRV_MAX6900 is not set +# CONFIG_RTC_DRV_RS5C372 is not set +CONFIG_RTC_DRV_ISL1208=m +# CONFIG_RTC_DRV_X1205 is not set +# CONFIG_RTC_DRV_PCF8563 is not set +# CONFIG_RTC_DRV_PCF8583 is not set +# CONFIG_RTC_DRV_M41T80 is not set +# CONFIG_RTC_DRV_S35390A is not set +# CONFIG_RTC_DRV_FM3130 is not set +# CONFIG_RTC_DRV_RX8581 is not set +# CONFIG_RTC_DRV_RX8025 is not set + +# +# SPI RTC drivers +# +# CONFIG_RTC_DRV_M41T94 is not set +# CONFIG_RTC_DRV_DS1305 is not set +# CONFIG_RTC_DRV_DS1390 is not set +# CONFIG_RTC_DRV_MAX6902 is not set +# CONFIG_RTC_DRV_R9701 is not set +# CONFIG_RTC_DRV_RS5C348 is not set +# CONFIG_RTC_DRV_DS3234 is not set +# CONFIG_RTC_DRV_PCF2123 is not set + +# +# Platform RTC drivers +# +# CONFIG_RTC_DRV_CMOS is not set +# CONFIG_RTC_DRV_DS1286 is not set +# CONFIG_RTC_DRV_DS1511 is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T35 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_MSM6242 is not set +# CONFIG_RTC_DRV_BQ4802 is not set +# CONFIG_RTC_DRV_RP5C01 is not set +# CONFIG_RTC_DRV_V3020 is not set + +# +# on-CPU RTC drivers +# +# CONFIG_RTC_DRV_SA1100 is not set +CONFIG_RTC_DRV_PXA=m +# CONFIG_DMADEVICES is not set +# CONFIG_AUXDISPLAY is not set +# CONFIG_UIO is not set + +# +# TI VLYNQ +# +# CONFIG_STAGING is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=y +# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set +# CONFIG_EXT3_FS_XATTR is not set +# CONFIG_EXT4_FS is not set +CONFIG_JBD=y +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_BTRFS_FS is not set +# CONFIG_NILFS2_FS is not set +CONFIG_FILE_LOCKING=y +CONFIG_FSNOTIFY=y +# CONFIG_DNOTIFY is not set +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# Caches +# +# CONFIG_FSCACHE is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=m +# CONFIG_MSDOS_FS is not set +CONFIG_VFAT_FS=m +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_SYSCTL=y +CONFIG_PROC_PAGE_MONITOR=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set +CONFIG_MISC_FILESYSTEMS=y +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +CONFIG_JFFS2_FS=y +CONFIG_JFFS2_FS_DEBUG=0 +CONFIG_JFFS2_FS_WRITEBUFFER=y +# CONFIG_JFFS2_FS_WBUF_VERIFY is not set +# CONFIG_JFFS2_SUMMARY is not set +# CONFIG_JFFS2_FS_XATTR is not set +# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set +CONFIG_JFFS2_ZLIB=y +# CONFIG_JFFS2_LZO is not set +CONFIG_JFFS2_RTIME=y +# CONFIG_JFFS2_RUBIN is not set +# CONFIG_CRAMFS is not set +# CONFIG_SQUASHFS is not set +# CONFIG_VXFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_ROMFS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +# CONFIG_NFS_V4 is not set +CONFIG_ROOT_NFS=y +CONFIG_NFSD=m +CONFIG_NFSD_V3=y +# CONFIG_NFSD_V3_ACL is not set +# CONFIG_NFSD_V4 is not set +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_EXPORTFS=m +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +# CONFIG_RPCSEC_GSS_KRB5 is not set +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +CONFIG_PARTITION_ADVANCED=y +# CONFIG_ACORN_PARTITION is not set +# CONFIG_OSF_PARTITION is not set +# CONFIG_AMIGA_PARTITION is not set +# CONFIG_ATARI_PARTITION is not set +# CONFIG_MAC_PARTITION is not set +CONFIG_MSDOS_PARTITION=y +# CONFIG_BSD_DISKLABEL is not set +# CONFIG_MINIX_SUBPARTITION is not set +# CONFIG_SOLARIS_X86_PARTITION is not set +# CONFIG_UNIXWARE_DISKLABEL is not set +# CONFIG_LDM_PARTITION is not set +# CONFIG_SGI_PARTITION is not set +# CONFIG_ULTRIX_PARTITION is not set +# CONFIG_SUN_PARTITION is not set +# CONFIG_KARMA_PARTITION is not set +# CONFIG_EFI_PARTITION is not set +# CONFIG_SYSV68_PARTITION is not set +CONFIG_NLS=m +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=m +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +CONFIG_NLS_CODEPAGE_850=m +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +CONFIG_NLS_ISO8859_1=m +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +CONFIG_NLS_ISO8859_15=m +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +CONFIG_NLS_UTF8=m +# CONFIG_DLM is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 +CONFIG_MAGIC_SYSRQ=y +# CONFIG_STRIP_ASM_SYMS is not set +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 +CONFIG_DETECT_HUNG_TASK=y +# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set +CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0 +CONFIG_SCHED_DEBUG=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set +# CONFIG_SLUB_DEBUG_ON is not set +# CONFIG_SLUB_STATS is not set +# CONFIG_DEBUG_KMEMLEAK is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +CONFIG_DEBUG_MUTEXES=y +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +CONFIG_DEBUG_BUGVERBOSE=y +# CONFIG_DEBUG_INFO is not set +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_WRITECOUNT is not set +CONFIG_DEBUG_MEMORY_INIT=y +# CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set +# CONFIG_DEBUG_NOTIFIERS is not set +# CONFIG_DEBUG_CREDENTIALS is not set +# CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set +# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_LATENCYTOP is not set +CONFIG_SYSCTL_SYSCALL_CHECK=y +# CONFIG_PAGE_POISONING is not set +CONFIG_HAVE_FUNCTION_TRACER=y +CONFIG_TRACING_SUPPORT=y +CONFIG_FTRACE=y +# CONFIG_FUNCTION_TRACER is not set +# CONFIG_IRQSOFF_TRACER is not set +# CONFIG_SCHED_TRACER is not set +# CONFIG_ENABLE_DEFAULT_TRACERS is not set +# CONFIG_BOOT_TRACER is not set +CONFIG_BRANCH_PROFILE_NONE=y +# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set +# CONFIG_PROFILE_ALL_BRANCHES is not set +# CONFIG_STACK_TRACER is not set +# CONFIG_KMEMTRACE is not set +# CONFIG_WORKQUEUE_TRACER is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_KGDB is not set +CONFIG_ARM_UNWIND=y +# CONFIG_DEBUG_USER is not set +CONFIG_DEBUG_ERRORS=y +# CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_DEBUG_LL is not set +# CONFIG_OC_ETM is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set +# CONFIG_SECURITYFS is not set +# CONFIG_DEFAULT_SECURITY_SELINUX is not set +# CONFIG_DEFAULT_SECURITY_SMACK is not set +# CONFIG_DEFAULT_SECURITY_TOMOYO is not set +CONFIG_DEFAULT_SECURITY_DAC=y +CONFIG_DEFAULT_SECURITY="" +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +CONFIG_CRYPTO_ALGAPI=m +CONFIG_CRYPTO_ALGAPI2=m +CONFIG_CRYPTO_AEAD2=m +CONFIG_CRYPTO_BLKCIPHER=m +CONFIG_CRYPTO_BLKCIPHER2=m +CONFIG_CRYPTO_HASH=m +CONFIG_CRYPTO_HASH2=m +CONFIG_CRYPTO_RNG2=m +CONFIG_CRYPTO_PCOMP=m +CONFIG_CRYPTO_MANAGER=m +CONFIG_CRYPTO_MANAGER2=m +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_NULL is not set +CONFIG_CRYPTO_WORKQUEUE=m +# CONFIG_CRYPTO_CRYPTD is not set +# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +# CONFIG_CRYPTO_CBC is not set +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +CONFIG_CRYPTO_ECB=m +# CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_PCBC is not set +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set +# CONFIG_CRYPTO_VMAC is not set + +# +# Digest +# +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_GHASH is not set +# CONFIG_CRYPTO_MD4 is not set +# CONFIG_CRYPTO_MD5 is not set +CONFIG_CRYPTO_MICHAEL_MIC=m +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# +CONFIG_CRYPTO_AES=m +# CONFIG_CRYPTO_ANUBIS is not set +CONFIG_CRYPTO_ARC4=m +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +# CONFIG_CRYPTO_DES is not set +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_ZLIB is not set +# CONFIG_CRYPTO_LZO is not set + +# +# Random Number Generation +# +# CONFIG_CRYPTO_ANSI_CPRNG is not set +CONFIG_CRYPTO_HW=y +# CONFIG_BINARY_PRINTF is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +CONFIG_GENERIC_FIND_LAST_BIT=y +CONFIG_CRC_CCITT=m +CONFIG_CRC16=m +CONFIG_CRC_T10DIF=m +CONFIG_CRC_ITU_T=m +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y +CONFIG_ZLIB_DEFLATE=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y +CONFIG_NLATTR=y diff --git a/arch/arm/include/asm/elf.h b/arch/arm/include/asm/elf.h index 6aac3f5bb2f3..a399bb5730f1 100644 --- a/arch/arm/include/asm/elf.h +++ b/arch/arm/include/asm/elf.h @@ -101,7 +101,6 @@ extern int arm_elf_read_implies_exec(const struct elf32_hdr *, int); int dump_task_regs(struct task_struct *t, elf_gregset_t *elfregs); #define ELF_CORE_COPY_TASK_REGS dump_task_regs -#define USE_ELF_CORE_DUMP #define ELF_EXEC_PAGESIZE 4096 /* This is the location that an ET_DYN program is loaded if exec'ed. Typical diff --git a/arch/arm/include/asm/mach/irq.h b/arch/arm/include/asm/mach/irq.h index acac5302e4ea..8920b2d6e3b8 100644 --- a/arch/arm/include/asm/mach/irq.h +++ b/arch/arm/include/asm/mach/irq.h @@ -26,9 +26,9 @@ extern int show_fiq_list(struct seq_file *, void *); */ #define do_bad_IRQ(irq,desc) \ do { \ - spin_lock(&desc->lock); \ + raw_spin_lock(&desc->lock); \ handle_bad_irq(irq, desc); \ - spin_unlock(&desc->lock); \ + raw_spin_unlock(&desc->lock); \ } while(0) #endif diff --git a/arch/arm/include/asm/spinlock.h b/arch/arm/include/asm/spinlock.h index c13681ac1ede..c91c64cab922 100644 --- a/arch/arm/include/asm/spinlock.h +++ b/arch/arm/include/asm/spinlock.h @@ -17,13 +17,13 @@ * Locked value: 1 */ -#define __raw_spin_is_locked(x) ((x)->lock != 0) -#define __raw_spin_unlock_wait(lock) \ - do { while (__raw_spin_is_locked(lock)) cpu_relax(); } while (0) +#define arch_spin_is_locked(x) ((x)->lock != 0) +#define arch_spin_unlock_wait(lock) \ + do { while (arch_spin_is_locked(lock)) cpu_relax(); } while (0) -#define __raw_spin_lock_flags(lock, flags) __raw_spin_lock(lock) +#define arch_spin_lock_flags(lock, flags) arch_spin_lock(lock) -static inline void __raw_spin_lock(raw_spinlock_t *lock) +static inline void arch_spin_lock(arch_spinlock_t *lock) { unsigned long tmp; @@ -43,7 +43,7 @@ static inline void __raw_spin_lock(raw_spinlock_t *lock) smp_mb(); } -static inline int __raw_spin_trylock(raw_spinlock_t *lock) +static inline int arch_spin_trylock(arch_spinlock_t *lock) { unsigned long tmp; @@ -63,7 +63,7 @@ static inline int __raw_spin_trylock(raw_spinlock_t *lock) } } -static inline void __raw_spin_unlock(raw_spinlock_t *lock) +static inline void arch_spin_unlock(arch_spinlock_t *lock) { smp_mb(); @@ -86,7 +86,7 @@ static inline void __raw_spin_unlock(raw_spinlock_t *lock) * just write zero since the lock is exclusively held. */ -static inline void __raw_write_lock(raw_rwlock_t *rw) +static inline void arch_write_lock(arch_rwlock_t *rw) { unsigned long tmp; @@ -106,7 +106,7 @@ static inline void __raw_write_lock(raw_rwlock_t *rw) smp_mb(); } -static inline int __raw_write_trylock(raw_rwlock_t *rw) +static inline int arch_write_trylock(arch_rwlock_t *rw) { unsigned long tmp; @@ -126,7 +126,7 @@ static inline int __raw_write_trylock(raw_rwlock_t *rw) } } -static inline void __raw_write_unlock(raw_rwlock_t *rw) +static inline void arch_write_unlock(arch_rwlock_t *rw) { smp_mb(); @@ -142,7 +142,7 @@ static inline void __raw_write_unlock(raw_rwlock_t *rw) } /* write_can_lock - would write_trylock() succeed? */ -#define __raw_write_can_lock(x) ((x)->lock == 0) +#define arch_write_can_lock(x) ((x)->lock == 0) /* * Read locks are a bit more hairy: @@ -156,7 +156,7 @@ static inline void __raw_write_unlock(raw_rwlock_t *rw) * currently active. However, we know we won't have any write * locks. */ -static inline void __raw_read_lock(raw_rwlock_t *rw) +static inline void arch_read_lock(arch_rwlock_t *rw) { unsigned long tmp, tmp2; @@ -176,7 +176,7 @@ static inline void __raw_read_lock(raw_rwlock_t *rw) smp_mb(); } -static inline void __raw_read_unlock(raw_rwlock_t *rw) +static inline void arch_read_unlock(arch_rwlock_t *rw) { unsigned long tmp, tmp2; @@ -198,7 +198,7 @@ static inline void __raw_read_unlock(raw_rwlock_t *rw) : "cc"); } -static inline int __raw_read_trylock(raw_rwlock_t *rw) +static inline int arch_read_trylock(arch_rwlock_t *rw) { unsigned long tmp, tmp2 = 1; @@ -215,13 +215,13 @@ static inline int __raw_read_trylock(raw_rwlock_t *rw) } /* read_can_lock - would read_trylock() succeed? */ -#define __raw_read_can_lock(x) ((x)->lock < 0x80000000) +#define arch_read_can_lock(x) ((x)->lock < 0x80000000) -#define __raw_read_lock_flags(lock, flags) __raw_read_lock(lock) -#define __raw_write_lock_flags(lock, flags) __raw_write_lock(lock) +#define arch_read_lock_flags(lock, flags) arch_read_lock(lock) +#define arch_write_lock_flags(lock, flags) arch_write_lock(lock) -#define _raw_spin_relax(lock) cpu_relax() -#define _raw_read_relax(lock) cpu_relax() -#define _raw_write_relax(lock) cpu_relax() +#define arch_spin_relax(lock) cpu_relax() +#define arch_read_relax(lock) cpu_relax() +#define arch_write_relax(lock) cpu_relax() #endif /* __ASM_SPINLOCK_H */ diff --git a/arch/arm/include/asm/spinlock_types.h b/arch/arm/include/asm/spinlock_types.h index 43e83f6d2ee5..d14d197ae04a 100644 --- a/arch/arm/include/asm/spinlock_types.h +++ b/arch/arm/include/asm/spinlock_types.h @@ -7,14 +7,14 @@ typedef struct { volatile unsigned int lock; -} raw_spinlock_t; +} arch_spinlock_t; -#define __RAW_SPIN_LOCK_UNLOCKED { 0 } +#define __ARCH_SPIN_LOCK_UNLOCKED { 0 } typedef struct { volatile unsigned int lock; -} raw_rwlock_t; +} arch_rwlock_t; -#define __RAW_RW_LOCK_UNLOCKED { 0 } +#define __ARCH_RW_LOCK_UNLOCKED { 0 } #endif diff --git a/arch/arm/kernel/Makefile b/arch/arm/kernel/Makefile index e7ccf7e697ce..dd00f747e2ad 100644 --- a/arch/arm/kernel/Makefile +++ b/arch/arm/kernel/Makefile @@ -54,5 +54,6 @@ endif head-y := head$(MMUEXT).o obj-$(CONFIG_DEBUG_LL) += debug.o +obj-$(CONFIG_EARLY_PRINTK) += early_printk.o extra-y := $(head-y) init_task.o vmlinux.lds diff --git a/arch/arm/kernel/armksyms.c b/arch/arm/kernel/armksyms.c index 0e627705f746..8214bfebfaca 100644 --- a/arch/arm/kernel/armksyms.c +++ b/arch/arm/kernel/armksyms.c @@ -48,27 +48,7 @@ extern void __aeabi_uidivmod(void); extern void __aeabi_ulcmp(void); extern void fpundefinstr(void); -extern void fp_enter(void); -/* - * This has a special calling convention; it doesn't - * modify any of the usual registers, except for LR. - */ -#define EXPORT_CRC_ALIAS(sym) __CRC_SYMBOL(sym, "") - -#define EXPORT_SYMBOL_ALIAS(sym,orig) \ - EXPORT_CRC_ALIAS(sym) \ - static const struct kernel_symbol __ksymtab_##sym \ - __used __attribute__((section("__ksymtab"))) = \ - { (unsigned long)&orig, #sym }; - -/* - * floating point math emulator support. - * These symbols will never change their calling convention... - */ -EXPORT_SYMBOL_ALIAS(kern_fp_enter,fp_enter); -EXPORT_SYMBOL_ALIAS(fp_printk,printk); -EXPORT_SYMBOL_ALIAS(fp_send_sig,send_sig); EXPORT_SYMBOL(__backtrace); diff --git a/arch/arm/kernel/early_printk.c b/arch/arm/kernel/early_printk.c new file mode 100644 index 000000000000..85aa2b292692 --- /dev/null +++ b/arch/arm/kernel/early_printk.c @@ -0,0 +1,57 @@ +/* + * linux/arch/arm/kernel/early_printk.c + * + * Copyright (C) 2009 Sascha Hauer <s.hauer@pengutronix.de> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/console.h> +#include <linux/init.h> + +extern void printch(int); + +static void early_write(const char *s, unsigned n) +{ + while (n-- > 0) { + if (*s == '\n') + printch('\r'); + printch(*s); + s++; + } +} + +static void early_console_write(struct console *con, const char *s, unsigned n) +{ + early_write(s, n); +} + +static struct console early_console = { + .name = "earlycon", + .write = early_console_write, + .flags = CON_PRINTBUFFER | CON_BOOT, + .index = -1, +}; + +asmlinkage void early_printk(const char *fmt, ...) +{ + char buf[512]; + int n; + va_list ap; + + va_start(ap, fmt); + n = vscnprintf(buf, sizeof(buf), fmt, ap); + early_write(buf, n); + va_end(ap); +} + +static int __init setup_early_printk(char *buf) +{ + register_console(&early_console); + return 0; +} + +early_param("earlyprintk", setup_early_printk); diff --git a/arch/arm/kernel/irq.c b/arch/arm/kernel/irq.c index c9a8619f3856..b7cb45bb91e8 100644 --- a/arch/arm/kernel/irq.c +++ b/arch/arm/kernel/irq.c @@ -69,7 +69,7 @@ int show_interrupts(struct seq_file *p, void *v) } if (i < NR_IRQS) { - spin_lock_irqsave(&irq_desc[i].lock, flags); + raw_spin_lock_irqsave(&irq_desc[i].lock, flags); action = irq_desc[i].action; if (!action) goto unlock; @@ -84,7 +84,7 @@ int show_interrupts(struct seq_file *p, void *v) seq_putc(p, '\n'); unlock: - spin_unlock_irqrestore(&irq_desc[i].lock, flags); + raw_spin_unlock_irqrestore(&irq_desc[i].lock, flags); } else if (i == NR_IRQS) { #ifdef CONFIG_FIQ show_fiq_list(p, v); @@ -139,7 +139,7 @@ void set_irq_flags(unsigned int irq, unsigned int iflags) } desc = irq_desc + irq; - spin_lock_irqsave(&desc->lock, flags); + raw_spin_lock_irqsave(&desc->lock, flags); desc->status |= IRQ_NOREQUEST | IRQ_NOPROBE | IRQ_NOAUTOEN; if (iflags & IRQF_VALID) desc->status &= ~IRQ_NOREQUEST; @@ -147,7 +147,7 @@ void set_irq_flags(unsigned int irq, unsigned int iflags) desc->status &= ~IRQ_NOPROBE; if (!(iflags & IRQF_NOAUTOEN)) desc->status &= ~IRQ_NOAUTOEN; - spin_unlock_irqrestore(&desc->lock, flags); + raw_spin_unlock_irqrestore(&desc->lock, flags); } void __init init_IRQ(void) @@ -166,9 +166,9 @@ static void route_irq(struct irq_desc *desc, unsigned int irq, unsigned int cpu) { pr_debug("IRQ%u: moving from cpu%u to cpu%u\n", irq, desc->node, cpu); - spin_lock_irq(&desc->lock); + raw_spin_lock_irq(&desc->lock); desc->chip->set_affinity(irq, cpumask_of(cpu)); - spin_unlock_irq(&desc->lock); + raw_spin_unlock_irq(&desc->lock); } /* diff --git a/arch/arm/kernel/smp_twd.c b/arch/arm/kernel/smp_twd.c index a73a34dccf2a..ea02a7b1c244 100644 --- a/arch/arm/kernel/smp_twd.c +++ b/arch/arm/kernel/smp_twd.c @@ -160,6 +160,7 @@ void __cpuinit twd_timer_setup(struct clock_event_device *clk) /* Make sure our local interrupt controller has this enabled */ local_irq_save(flags); + irq_to_desc(clk->irq)->status |= IRQ_NOPROBE; get_irq_chip(clk->irq)->unmask(clk->irq); local_irq_restore(flags); diff --git a/arch/arm/kernel/vmlinux.lds.S b/arch/arm/kernel/vmlinux.lds.S index 71151bd87a36..4957e13ef55b 100644 --- a/arch/arm/kernel/vmlinux.lds.S +++ b/arch/arm/kernel/vmlinux.lds.S @@ -65,11 +65,11 @@ SECTIONS __init_end = .; #endif - /DISCARD/ : { /* Exit code and data */ - EXIT_TEXT - EXIT_DATA - *(.exitcall.exit) - *(.discard) + /* + * unwind exit sections must be discarded before the rest of the + * unwind sections get included. + */ + /DISCARD/ : { *(.ARM.exidx.exit.text) *(.ARM.extab.exit.text) #ifndef CONFIG_HOTPLUG_CPU @@ -238,6 +238,9 @@ SECTIONS STABS_DEBUG .comment 0 : { *(.comment) } + + /* Default discards */ + DISCARDS } /* diff --git a/arch/arm/mach-at91/include/mach/atmel-mci.h b/arch/arm/mach-at91/include/mach/atmel-mci.h new file mode 100644 index 000000000000..998cb0c07135 --- /dev/null +++ b/arch/arm/mach-at91/include/mach/atmel-mci.h @@ -0,0 +1,24 @@ +#ifndef __MACH_ATMEL_MCI_H +#define __MACH_ATMEL_MCI_H + +#include <mach/at_hdmac.h> + +/** + * struct mci_dma_data - DMA data for MCI interface + */ +struct mci_dma_data { + struct at_dma_slave sdata; +}; + +/* accessor macros */ +#define slave_data_ptr(s) (&(s)->sdata) +#define find_slave_dev(s) ((s)->sdata.dma_dev) + +#define setup_dma_addr(s, t, r) do { \ + if (s) { \ + (s)->sdata.tx_reg = (t); \ + (s)->sdata.rx_reg = (r); \ + } \ +} while (0) + +#endif /* __MACH_ATMEL_MCI_H */ diff --git a/arch/arm/mach-bcmring/arch.c b/arch/arm/mach-bcmring/arch.c index fbe6fa02c882..53dd2a9eecf9 100644 --- a/arch/arm/mach-bcmring/arch.c +++ b/arch/arm/mach-bcmring/arch.c @@ -70,9 +70,19 @@ static struct ctl_table bcmring_sysctl_reboot[] = { {} }; +static struct resource nand_resource[] = { + [0] = { + .start = MM_ADDR_IO_NAND, + .end = MM_ADDR_IO_NAND + 0x1000 - 1, + .flags = IORESOURCE_MEM, + }, +}; + static struct platform_device nand_device = { .name = "bcm-nand", .id = -1, + .resource = nand_resource, + .num_resources = ARRAY_SIZE(nand_resource), }; static struct platform_device *devices[] __initdata = { diff --git a/arch/arm/mach-bcmring/include/mach/reg_nand.h b/arch/arm/mach-bcmring/include/mach/reg_nand.h new file mode 100644 index 000000000000..387376ffb56b --- /dev/null +++ b/arch/arm/mach-bcmring/include/mach/reg_nand.h @@ -0,0 +1,66 @@ +/***************************************************************************** +* Copyright 2001 - 2008 Broadcom Corporation. All rights reserved. +* +* Unless you and Broadcom execute a separate written software license +* agreement governing use of this software, this software is licensed to you +* under the terms of the GNU General Public License version 2, available at +* http://www.broadcom.com/licenses/GPLv2.php (the "GPL"). +* +* Notwithstanding the above, under no circumstances may you combine this +* software in any way with any other Broadcom software provided under a +* license other than the GPL, without Broadcom's express prior written +* consent. +*****************************************************************************/ + +/* +* +***************************************************************************** +* +* REG_NAND.h +* +* PURPOSE: +* +* This file contains definitions for the nand registers: +* +* NOTES: +* +*****************************************************************************/ + +#if !defined(__ASM_ARCH_REG_NAND_H) +#define __ASM_ARCH_REG_NAND_H + +/* ---- Include Files ---------------------------------------------------- */ +#include <csp/reg.h> +#include <mach/reg_umi.h> + +/* ---- Constants and Types ---------------------------------------------- */ + +#define HW_NAND_BASE MM_IO_BASE_NAND /* NAND Flash */ + +/* DMA accesses by the bootstrap need hard nonvirtual addresses */ +#define REG_NAND_CMD __REG16(HW_NAND_BASE + 0) +#define REG_NAND_ADDR __REG16(HW_NAND_BASE + 4) + +#define REG_NAND_PHYS_DATA16 (HW_NAND_BASE + 8) +#define REG_NAND_PHYS_DATA8 (HW_NAND_BASE + 8) +#define REG_NAND_DATA16 __REG16(REG_NAND_PHYS_DATA16) +#define REG_NAND_DATA8 __REG8(REG_NAND_PHYS_DATA8) + +/* use appropriate offset to make sure it start at the 1K boundary */ +#define REG_NAND_PHYS_DATA_DMA (HW_NAND_BASE + 0x400) +#define REG_NAND_DATA_DMA __REG32(REG_NAND_PHYS_DATA_DMA) + +/* Linux DMA requires physical address of the data register */ +#define REG_NAND_DATA16_PADDR HW_IO_VIRT_TO_PHYS(REG_NAND_PHYS_DATA16) +#define REG_NAND_DATA8_PADDR HW_IO_VIRT_TO_PHYS(REG_NAND_PHYS_DATA8) +#define REG_NAND_DATA_PADDR HW_IO_VIRT_TO_PHYS(REG_NAND_PHYS_DATA_DMA) + +#define NAND_BUS_16BIT() (0) +#define NAND_BUS_8BIT() (!NAND_BUS_16BIT()) + +/* Register offsets */ +#define REG_NAND_CMD_OFFSET (0) +#define REG_NAND_ADDR_OFFSET (4) +#define REG_NAND_DATA8_OFFSET (8) + +#endif diff --git a/arch/arm/mach-bcmring/include/mach/reg_umi.h b/arch/arm/mach-bcmring/include/mach/reg_umi.h new file mode 100644 index 000000000000..06a355481ea6 --- /dev/null +++ b/arch/arm/mach-bcmring/include/mach/reg_umi.h @@ -0,0 +1,237 @@ +/***************************************************************************** +* Copyright 2005 - 2008 Broadcom Corporation. All rights reserved. +* +* Unless you and Broadcom execute a separate written software license +* agreement governing use of this software, this software is licensed to you +* under the terms of the GNU General Public License version 2, available at +* http://www.broadcom.com/licenses/GPLv2.php (the "GPL"). +* +* Notwithstanding the above, under no circumstances may you combine this +* software in any way with any other Broadcom software provided under a +* license other than the GPL, without Broadcom's express prior written +* consent. +*****************************************************************************/ + +/* +* +***************************************************************************** +* +* REG_UMI.h +* +* PURPOSE: +* +* This file contains definitions for the nand registers: +* +* NOTES: +* +*****************************************************************************/ + +#if !defined(__ASM_ARCH_REG_UMI_H) +#define __ASM_ARCH_REG_UMI_H + +/* ---- Include Files ---------------------------------------------------- */ +#include <csp/reg.h> +#include <mach/csp/mm_io.h> + +/* ---- Constants and Types ---------------------------------------------- */ + +/* Unified Memory Interface Ctrl Register */ +#define HW_UMI_BASE MM_IO_BASE_UMI + +/* Flash bank 0 timing and control register */ +#define REG_UMI_FLASH0_TCR __REG32(HW_UMI_BASE + 0x00) +/* Flash bank 1 timing and control register */ +#define REG_UMI_FLASH1_TCR __REG32(HW_UMI_BASE + 0x04) +/* Flash bank 2 timing and control register */ +#define REG_UMI_FLASH2_TCR __REG32(HW_UMI_BASE + 0x08) +/* MMD interface and control register */ +#define REG_UMI_MMD_ICR __REG32(HW_UMI_BASE + 0x0c) +/* NAND timing and control register */ +#define REG_UMI_NAND_TCR __REG32(HW_UMI_BASE + 0x18) +/* NAND ready/chip select register */ +#define REG_UMI_NAND_RCSR __REG32(HW_UMI_BASE + 0x1c) +/* NAND ECC control & status register */ +#define REG_UMI_NAND_ECC_CSR __REG32(HW_UMI_BASE + 0x20) +/* NAND ECC data register XXB2B1B0 */ +#define REG_UMI_NAND_ECC_DATA __REG32(HW_UMI_BASE + 0x24) +/* BCH ECC Parameter N */ +#define REG_UMI_BCH_N __REG32(HW_UMI_BASE + 0x40) +/* BCH ECC Parameter T */ +#define REG_UMI_BCH_K __REG32(HW_UMI_BASE + 0x44) +/* BCH ECC Parameter K */ +#define REG_UMI_BCH_T __REG32(HW_UMI_BASE + 0x48) +/* BCH ECC Contro Status */ +#define REG_UMI_BCH_CTRL_STATUS __REG32(HW_UMI_BASE + 0x4C) +/* BCH WR ECC 31:0 */ +#define REG_UMI_BCH_WR_ECC_0 __REG32(HW_UMI_BASE + 0x50) +/* BCH WR ECC 63:32 */ +#define REG_UMI_BCH_WR_ECC_1 __REG32(HW_UMI_BASE + 0x54) +/* BCH WR ECC 95:64 */ +#define REG_UMI_BCH_WR_ECC_2 __REG32(HW_UMI_BASE + 0x58) +/* BCH WR ECC 127:96 */ +#define REG_UMI_BCH_WR_ECC_3 __REG32(HW_UMI_BASE + 0x5c) +/* BCH WR ECC 155:128 */ +#define REG_UMI_BCH_WR_ECC_4 __REG32(HW_UMI_BASE + 0x60) +/* BCH Read Error Location 1,0 */ +#define REG_UMI_BCH_RD_ERR_LOC_1_0 __REG32(HW_UMI_BASE + 0x64) +/* BCH Read Error Location 3,2 */ +#define REG_UMI_BCH_RD_ERR_LOC_3_2 __REG32(HW_UMI_BASE + 0x68) +/* BCH Read Error Location 5,4 */ +#define REG_UMI_BCH_RD_ERR_LOC_5_4 __REG32(HW_UMI_BASE + 0x6c) +/* BCH Read Error Location 7,6 */ +#define REG_UMI_BCH_RD_ERR_LOC_7_6 __REG32(HW_UMI_BASE + 0x70) +/* BCH Read Error Location 9,8 */ +#define REG_UMI_BCH_RD_ERR_LOC_9_8 __REG32(HW_UMI_BASE + 0x74) +/* BCH Read Error Location 11,10 */ +#define REG_UMI_BCH_RD_ERR_LOC_B_A __REG32(HW_UMI_BASE + 0x78) + +/* REG_UMI_FLASH0/1/2_TCR, REG_UMI_SRAM0/1_TCR bits */ +/* Enable wait pin during burst write or read */ +#define REG_UMI_TCR_WAITEN 0x80000000 +/* Enable mem ctrlr to work iwth ext mem of lower freq than AHB clk */ +#define REG_UMI_TCR_LOWFREQ 0x40000000 +/* 1=synch write, 0=async write */ +#define REG_UMI_TCR_MEMTYPE_SYNCWRITE 0x20000000 +/* 1=synch read, 0=async read */ +#define REG_UMI_TCR_MEMTYPE_SYNCREAD 0x10000000 +/* 1=page mode read, 0=normal mode read */ +#define REG_UMI_TCR_MEMTYPE_PAGEREAD 0x08000000 +/* page size/burst size (wrap only) */ +#define REG_UMI_TCR_MEMTYPE_PGSZ_MASK 0x07000000 +/* 4 word */ +#define REG_UMI_TCR_MEMTYPE_PGSZ_4 0x00000000 +/* 8 word */ +#define REG_UMI_TCR_MEMTYPE_PGSZ_8 0x01000000 +/* 16 word */ +#define REG_UMI_TCR_MEMTYPE_PGSZ_16 0x02000000 +/* 32 word */ +#define REG_UMI_TCR_MEMTYPE_PGSZ_32 0x03000000 +/* 64 word */ +#define REG_UMI_TCR_MEMTYPE_PGSZ_64 0x04000000 +/* 128 word */ +#define REG_UMI_TCR_MEMTYPE_PGSZ_128 0x05000000 +/* 256 word */ +#define REG_UMI_TCR_MEMTYPE_PGSZ_256 0x06000000 +/* 512 word */ +#define REG_UMI_TCR_MEMTYPE_PGSZ_512 0x07000000 +/* Page read access cycle / Burst write latency (n+2 / n+1) */ +#define REG_UMI_TCR_TPRC_TWLC_MASK 0x00f80000 +/* Bus turnaround cycle (n) */ +#define REG_UMI_TCR_TBTA_MASK 0x00070000 +/* Write pulse width cycle (n+1) */ +#define REG_UMI_TCR_TWP_MASK 0x0000f800 +/* Write recovery cycle (n+1) */ +#define REG_UMI_TCR_TWR_MASK 0x00000600 +/* Write address setup cycle (n+1) */ +#define REG_UMI_TCR_TAS_MASK 0x00000180 +/* Output enable delay cycle (n) */ +#define REG_UMI_TCR_TOE_MASK 0x00000060 +/* Read access cycle / Burst read latency (n+2 / n+1) */ +#define REG_UMI_TCR_TRC_TLC_MASK 0x0000001f + +/* REG_UMI_MMD_ICR bits */ +/* Flash write protection pin control */ +#define REG_UMI_MMD_ICR_FLASH_WP 0x8000 +/* Extend hold time for sram0, sram1 csn (39 MHz operation) */ +#define REG_UMI_MMD_ICR_XHCS 0x4000 +/* Enable SDRAM 2 interface control */ +#define REG_UMI_MMD_ICR_SDRAM2EN 0x2000 +/* Enable merge of flash banks 0/1 to 512 MBit bank */ +#define REG_UMI_MMD_ICR_INST512 0x1000 +/* Enable merge of flash banks 1/2 to 512 MBit bank */ +#define REG_UMI_MMD_ICR_DATA512 0x0800 +/* Enable SDRAM interface control */ +#define REG_UMI_MMD_ICR_SDRAMEN 0x0400 +/* Polarity of busy state of Burst Wait Signal */ +#define REG_UMI_MMD_ICR_WAITPOL 0x0200 +/* Enable burst clock stopped when not accessing external burst flash/sram */ +#define REG_UMI_MMD_ICR_BCLKSTOP 0x0100 +/* Enable the peri1_csn to replace flash1_csn in 512 Mb flash mode */ +#define REG_UMI_MMD_ICR_PERI1EN 0x0080 +/* Enable the peri2_csn to replace sdram_csn */ +#define REG_UMI_MMD_ICR_PERI2EN 0x0040 +/* Enable the peri3_csn to replace sdram2_csn */ +#define REG_UMI_MMD_ICR_PERI3EN 0x0020 +/* Enable sram bank1 for H/W controlled MRS */ +#define REG_UMI_MMD_ICR_MRSB1 0x0010 +/* Enable sram bank0 for H/W controlled MRS */ +#define REG_UMI_MMD_ICR_MRSB0 0x0008 +/* Polarity for assert3ed state of H/W controlled MRS */ +#define REG_UMI_MMD_ICR_MRSPOL 0x0004 +/* 0: S/W controllable ZZ/MRS/CRE/P-Mode pin */ +/* 1: H/W controlled ZZ/MRS/CRE/P-Mode, same timing as CS */ +#define REG_UMI_MMD_ICR_MRSMODE 0x0002 +/* MRS state for S/W controlled mode */ +#define REG_UMI_MMD_ICR_MRSSTATE 0x0001 + +/* REG_UMI_NAND_TCR bits */ +/* Enable software to control CS */ +#define REG_UMI_NAND_TCR_CS_SWCTRL 0x80000000 +/* 16-bit nand wordsize if set */ +#define REG_UMI_NAND_TCR_WORD16 0x40000000 +/* Bus turnaround cycle (n) */ +#define REG_UMI_NAND_TCR_TBTA_MASK 0x00070000 +/* Write pulse width cycle (n+1) */ +#define REG_UMI_NAND_TCR_TWP_MASK 0x0000f800 +/* Write recovery cycle (n+1) */ +#define REG_UMI_NAND_TCR_TWR_MASK 0x00000600 +/* Write address setup cycle (n+1) */ +#define REG_UMI_NAND_TCR_TAS_MASK 0x00000180 +/* Output enable delay cycle (n) */ +#define REG_UMI_NAND_TCR_TOE_MASK 0x00000060 +/* Read access cycle (n+2) */ +#define REG_UMI_NAND_TCR_TRC_TLC_MASK 0x0000001f + +/* REG_UMI_NAND_RCSR bits */ +/* Status: Ready=1, Busy=0 */ +#define REG_UMI_NAND_RCSR_RDY 0x02 +/* Keep CS asserted during operation */ +#define REG_UMI_NAND_RCSR_CS_ASSERTED 0x01 + +/* REG_UMI_NAND_ECC_CSR bits */ +/* Interrupt status - read-only */ +#define REG_UMI_NAND_ECC_CSR_NANDINT 0x80000000 +/* Read: Status of ECC done, Write: clear ECC interrupt */ +#define REG_UMI_NAND_ECC_CSR_ECCINT_RAW 0x00800000 +/* Read: Status of R/B, Write: clear R/B interrupt */ +#define REG_UMI_NAND_ECC_CSR_RBINT_RAW 0x00400000 +/* 1 = Enable ECC Interrupt */ +#define REG_UMI_NAND_ECC_CSR_ECCINT_ENABLE 0x00008000 +/* 1 = Assert interrupt at rising edge of R/B_ */ +#define REG_UMI_NAND_ECC_CSR_RBINT_ENABLE 0x00004000 +/* Calculate ECC by 0=512 bytes, 1=256 bytes */ +#define REG_UMI_NAND_ECC_CSR_256BYTE 0x00000080 +/* Enable ECC in hardware */ +#define REG_UMI_NAND_ECC_CSR_ECC_ENABLE 0x00000001 + +/* REG_UMI_BCH_CTRL_STATUS bits */ +/* Shift to Indicate Number of correctable errors detected */ +#define REG_UMI_BCH_CTRL_STATUS_NB_CORR_ERROR_SHIFT 20 +/* Indicate Number of correctable errors detected */ +#define REG_UMI_BCH_CTRL_STATUS_NB_CORR_ERROR 0x00F00000 +/* Indicate Errors detected during read but uncorrectable */ +#define REG_UMI_BCH_CTRL_STATUS_UNCORR_ERR 0x00080000 +/* Indicate Errors detected during read and are correctable */ +#define REG_UMI_BCH_CTRL_STATUS_CORR_ERR 0x00040000 +/* Flag indicates BCH's ECC status of read process are valid */ +#define REG_UMI_BCH_CTRL_STATUS_RD_ECC_VALID 0x00020000 +/* Flag indicates BCH's ECC status of write process are valid */ +#define REG_UMI_BCH_CTRL_STATUS_WR_ECC_VALID 0x00010000 +/* Pause ECC calculation */ +#define REG_UMI_BCH_CTRL_STATUS_PAUSE_ECC_DEC 0x00000010 +/* Enable Interrupt */ +#define REG_UMI_BCH_CTRL_STATUS_INT_EN 0x00000004 +/* Enable ECC during read */ +#define REG_UMI_BCH_CTRL_STATUS_ECC_RD_EN 0x00000002 +/* Enable ECC during write */ +#define REG_UMI_BCH_CTRL_STATUS_ECC_WR_EN 0x00000001 +/* Mask for location */ +#define REG_UMI_BCH_ERR_LOC_MASK 0x00001FFF +/* location within a byte */ +#define REG_UMI_BCH_ERR_LOC_BYTE 0x00000007 +/* location within a word */ +#define REG_UMI_BCH_ERR_LOC_WORD 0x00000018 +/* location within a page (512 byte) */ +#define REG_UMI_BCH_ERR_LOC_PAGE 0x00001FE0 +#define REG_UMI_BCH_ERR_LOC_ADDR(index) (__REG32(HW_UMI_BASE + 0x64 + (index / 2)*4) >> ((index % 2) * 16)) +#endif diff --git a/arch/arm/mach-clps711x/include/mach/memory.h b/arch/arm/mach-clps711x/include/mach/memory.h index e522b20bcbc2..f70d52be48a2 100644 --- a/arch/arm/mach-clps711x/include/mach/memory.h +++ b/arch/arm/mach-clps711x/include/mach/memory.h @@ -30,6 +30,8 @@ #define __virt_to_bus(x) ((x) - PAGE_OFFSET) #define __bus_to_virt(x) ((x) + PAGE_OFFSET) +#define __pfn_to_bus(x) (__pfn_to_phys(x) - PHYS_OFFSET) +#define __bus_to_pfn(x) __phys_to_pfn((x) + PHYS_OFFSET) #endif diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c index 62b98bffc158..07de8db14581 100644 --- a/arch/arm/mach-davinci/board-da850-evm.c +++ b/arch/arm/mach-davinci/board-da850-evm.c @@ -339,6 +339,15 @@ static struct davinci_mmc_config da850_mmc_config = { .version = MMC_CTLR_VERSION_2, }; +static void da850_panel_power_ctrl(int val) +{ + /* lcd backlight */ + gpio_set_value(DA850_LCD_BL_PIN, val); + + /* lcd power */ + gpio_set_value(DA850_LCD_PWR_PIN, val); +} + static int da850_lcd_hw_init(void) { int status; @@ -356,17 +365,11 @@ static int da850_lcd_hw_init(void) gpio_direction_output(DA850_LCD_BL_PIN, 0); gpio_direction_output(DA850_LCD_PWR_PIN, 0); - /* disable lcd backlight */ - gpio_set_value(DA850_LCD_BL_PIN, 0); - - /* disable lcd power */ - gpio_set_value(DA850_LCD_PWR_PIN, 0); - - /* enable lcd power */ - gpio_set_value(DA850_LCD_PWR_PIN, 1); + /* Switch off panel power and backlight */ + da850_panel_power_ctrl(0); - /* enable lcd backlight */ - gpio_set_value(DA850_LCD_BL_PIN, 1); + /* Switch on panel power and backlight */ + da850_panel_power_ctrl(1); return 0; } @@ -674,6 +677,7 @@ static __init void da850_evm_init(void) pr_warning("da850_evm_init: lcd initialization failed: %d\n", ret); + sharp_lk043t1dg01_pdata.panel_power_ctrl = da850_panel_power_ctrl, ret = da8xx_register_lcdc(&sharp_lk043t1dg01_pdata); if (ret) pr_warning("da850_evm_init: lcdc registration failed: %d\n", diff --git a/arch/arm/mach-davinci/include/mach/nand.h b/arch/arm/mach-davinci/include/mach/nand.h index b520c4b5678a..b2ad8090bd10 100644 --- a/arch/arm/mach-davinci/include/mach/nand.h +++ b/arch/arm/mach-davinci/include/mach/nand.h @@ -79,6 +79,10 @@ struct davinci_nand_pdata { /* platform_data */ /* e.g. NAND_BUSWIDTH_16 or NAND_USE_FLASH_BBT */ unsigned options; + + /* Main and mirror bbt descriptor overrides */ + struct nand_bbt_descr *bbt_td; + struct nand_bbt_descr *bbt_md; }; #endif /* __ARCH_ARM_DAVINCI_NAND_H */ diff --git a/arch/arm/mach-ep93xx/include/mach/ep93xx_keypad.h b/arch/arm/mach-ep93xx/include/mach/ep93xx_keypad.h index 83f31cd0a274..62d17421e48c 100644 --- a/arch/arm/mach-ep93xx/include/mach/ep93xx_keypad.h +++ b/arch/arm/mach-ep93xx/include/mach/ep93xx_keypad.h @@ -5,9 +5,6 @@ #ifndef __ASM_ARCH_EP93XX_KEYPAD_H #define __ASM_ARCH_EP93XX_KEYPAD_H -#define MAX_MATRIX_KEY_ROWS (8) -#define MAX_MATRIX_KEY_COLS (8) - /* flags for the ep93xx_keypad driver */ #define EP93XX_KEYPAD_DISABLE_3_KEY (1<<0) /* disable 3-key reset */ #define EP93XX_KEYPAD_DIAG_MODE (1<<1) /* diagnostic mode */ @@ -18,8 +15,6 @@ /** * struct ep93xx_keypad_platform_data - platform specific device structure - * @matrix_key_rows: number of rows in the keypad matrix - * @matrix_key_cols: number of columns in the keypad matrix * @matrix_key_map: array of keycodes defining the keypad matrix * @matrix_key_map_size: ARRAY_SIZE(matrix_key_map) * @debounce: debounce start count; terminal count is 0xff @@ -27,8 +22,6 @@ * @flags: see above */ struct ep93xx_keypad_platform_data { - unsigned int matrix_key_rows; - unsigned int matrix_key_cols; unsigned int *matrix_key_map; int matrix_key_map_size; unsigned int debounce; @@ -36,7 +29,7 @@ struct ep93xx_keypad_platform_data { unsigned int flags; }; -/* macro for creating the matrix_key_map table */ -#define KEY(row, col, val) (((row) << 28) | ((col) << 24) | (val)) +#define EP93XX_MATRIX_ROWS (8) +#define EP93XX_MATRIX_COLS (8) #endif /* __ASM_ARCH_EP93XX_KEYPAD_H */ diff --git a/arch/arm/mach-footbridge/common.c b/arch/arm/mach-footbridge/common.c index b97f529e58e8..41febc796b1c 100644 --- a/arch/arm/mach-footbridge/common.c +++ b/arch/arm/mach-footbridge/common.c @@ -201,6 +201,11 @@ void __init footbridge_map_io(void) #ifdef CONFIG_FOOTBRIDGE_ADDIN +static inline unsigned long fb_bus_sdram_offset(void) +{ + return *CSR_PCISDRAMBASE & 0xfffffff0; +} + /* * These two functions convert virtual addresses to PCI addresses and PCI * addresses to virtual addresses. Note that it is only legal to use these @@ -210,14 +215,13 @@ unsigned long __virt_to_bus(unsigned long res) { WARN_ON(res < PAGE_OFFSET || res >= (unsigned long)high_memory); - return (res - PAGE_OFFSET) + (*CSR_PCISDRAMBASE & 0xfffffff0); + return res + (fb_bus_sdram_offset() - PAGE_OFFSET); } EXPORT_SYMBOL(__virt_to_bus); unsigned long __bus_to_virt(unsigned long res) { - res -= (*CSR_PCISDRAMBASE & 0xfffffff0); - res += PAGE_OFFSET; + res = res - (fb_bus_sdram_offset() - PAGE_OFFSET); WARN_ON(res < PAGE_OFFSET || res >= (unsigned long)high_memory); @@ -225,4 +229,16 @@ unsigned long __bus_to_virt(unsigned long res) } EXPORT_SYMBOL(__bus_to_virt); +unsigned long __pfn_to_bus(unsigned long pfn) +{ + return __pfn_to_phys(pfn) + (fb_bus_sdram_offset() - PHYS_OFFSET)); +} +EXPORT_SYMBOL(__pfn_to_bus); + +unsigned long __bus_to_pfn(unsigned long bus) +{ + return __phys_to_pfn(bus - (fb_bus_sdram_offset() - PHYS_OFFSET)); +} +EXPORT_SYMBOL(__bus_to_pfn); + #endif diff --git a/arch/arm/mach-footbridge/include/mach/memory.h b/arch/arm/mach-footbridge/include/mach/memory.h index cb16e59d87b6..8d64f4574087 100644 --- a/arch/arm/mach-footbridge/include/mach/memory.h +++ b/arch/arm/mach-footbridge/include/mach/memory.h @@ -29,6 +29,8 @@ #ifndef __ASSEMBLY__ extern unsigned long __virt_to_bus(unsigned long); extern unsigned long __bus_to_virt(unsigned long); +extern unsigned long __pfn_to_bus(unsigned long); +extern unsigned long __bus_to_pfn(unsigned long); #endif #define __virt_to_bus __virt_to_bus #define __bus_to_virt __bus_to_virt @@ -36,14 +38,15 @@ extern unsigned long __bus_to_virt(unsigned long); #elif defined(CONFIG_FOOTBRIDGE_HOST) /* - * The footbridge is programmed to expose the system RAM at the corresponding - * address. So, if PAGE_OFFSET is 0xc0000000, RAM appears at 0xe0000000. - * If 0x80000000, then its exposed at 0xa0000000 on the bus. etc. - * The only requirement is that the RAM isn't placed at bus address 0 which + * The footbridge is programmed to expose the system RAM at 0xe0000000. + * The requirement is that the RAM isn't placed at bus address 0, which * would clash with VGA cards. */ -#define __virt_to_bus(x) ((x) - 0xe0000000) -#define __bus_to_virt(x) ((x) + 0xe0000000) +#define BUS_OFFSET 0xe0000000 +#define __virt_to_bus(x) ((x) + (BUS_OFFSET - PAGE_OFFSET)) +#define __bus_to_virt(x) ((x) - (BUS_OFFSET - PAGE_OFFSET)) +#define __pfn_to_bus(x) (__pfn_to_phys(x) + (BUS_OFFSET - PHYS_OFFSET)) +#define __bus_to_pfn(x) __phys_to_pfn((x) - (BUS_OFFSET - PHYS_OFFSET)) #else diff --git a/arch/arm/mach-integrator/include/mach/memory.h b/arch/arm/mach-integrator/include/mach/memory.h index 4891828454f5..991f24d2c115 100644 --- a/arch/arm/mach-integrator/include/mach/memory.h +++ b/arch/arm/mach-integrator/include/mach/memory.h @@ -28,6 +28,7 @@ #define BUS_OFFSET UL(0x80000000) #define __virt_to_bus(x) ((x) - PAGE_OFFSET + BUS_OFFSET) #define __bus_to_virt(x) ((x) - BUS_OFFSET + PAGE_OFFSET) -#define __pfn_to_bus(x) (((x) << PAGE_SHIFT) + BUS_OFFSET) +#define __pfn_to_bus(x) (__pfn_to_phys(x) + (BUS_OFFSET - PHYS_OFFSET)) +#define __bus_to_pfn(x) __phys_to_pfn((x) - (BUS_OFFSET - PHYS_OFFSET)) #endif diff --git a/arch/arm/mach-ixp2000/include/mach/memory.h b/arch/arm/mach-ixp2000/include/mach/memory.h index aee7eb8a71b2..98e3471be15b 100644 --- a/arch/arm/mach-ixp2000/include/mach/memory.h +++ b/arch/arm/mach-ixp2000/include/mach/memory.h @@ -17,11 +17,15 @@ #include <mach/ixp2000-regs.h> -#define __virt_to_bus(v) \ - (((__virt_to_phys(v) - 0x0) + (*IXP2000_PCI_SDRAM_BAR & 0xfffffff0))) +#define IXP2000_PCI_SDRAM_OFFSET (*IXP2000_PCI_SDRAM_BAR & 0xfffffff0) -#define __bus_to_virt(b) \ - __phys_to_virt((((b - (*IXP2000_PCI_SDRAM_BAR & 0xfffffff0)) + 0x0))) +#define __phys_to_bus(x) ((x) + (IXP2000_PCI_SDRAM_OFFSET - PHYS_OFFSET)) +#define __bus_to_phys(x) ((x) - (IXP2000_PCI_SDRAM_OFFSET - PHYS_OFFSET)) + +#define __virt_to_bus(v) __phys_to_bus(__virt_to_phys(v)) +#define __bus_to_virt(b) __phys_to_virt(__bus_to_phys(b)) +#define __pfn_to_bus(p) __phys_to_bus(__pfn_to_phys(p)) +#define __bus_to_pfn(b) __phys_to_pfn(__bus_to_phys(b)) #endif diff --git a/arch/arm/mach-ixp23xx/include/mach/memory.h b/arch/arm/mach-ixp23xx/include/mach/memory.h index fdd138706c70..94a3a86cfeb8 100644 --- a/arch/arm/mach-ixp23xx/include/mach/memory.h +++ b/arch/arm/mach-ixp23xx/include/mach/memory.h @@ -19,16 +19,15 @@ */ #define PHYS_OFFSET (0x00000000) -#define __virt_to_bus(v) \ - ({ unsigned int ret; \ - ret = ((__virt_to_phys(v) - 0x00000000) + \ - (*((volatile int *)IXP23XX_PCI_SDRAM_BAR) & 0xfffffff0)); \ - ret; }) - -#define __bus_to_virt(b) \ - ({ unsigned int data; \ - data = *((volatile int *)IXP23XX_PCI_SDRAM_BAR); \ - __phys_to_virt((((b - (data & 0xfffffff0)) + 0x00000000))); }) +#define IXP23XX_PCI_SDRAM_OFFSET (*((volatile int *)IXP23XX_PCI_SDRAM_BAR) & 0xfffffff0)) + +#define __phys_to_bus(x) ((x) + (IXP23XX_PCI_SDRAM_OFFSET - PHYS_OFFSET)) +#define __bus_to_phys(x) ((x) - (IXP23XX_PCI_SDRAM_OFFSET - PHYS_OFFSET)) + +#define __virt_to_bus(v) __phys_to_bus(__virt_to_phys(v)) +#define __bus_to_virt(b) __phys_to_virt(__bus_to_phys(b)) +#define __pfn_to_bus(p) __phys_to_bus(__pfn_to_phys(p)) +#define __bus_to_pfn(b) __phys_to_pfn(__bus_to_phys(b)) #define arch_is_coherent() 1 diff --git a/arch/arm/mach-lh7a40x/clocks.c b/arch/arm/mach-lh7a40x/clocks.c index 6182f5410b4d..fcaf876f19b6 100644 --- a/arch/arm/mach-lh7a40x/clocks.c +++ b/arch/arm/mach-lh7a40x/clocks.c @@ -7,8 +7,6 @@ * version 2 as published by the Free Software Foundation. * */ - -#include <linux/cpufreq.h> #include <mach/hardware.h> #include <mach/clocks.h> #include <linux/err.h> @@ -31,12 +29,6 @@ struct clk { #define HCLKDIV(c) (((c) >> 0) & 0x02) #define PCLKDIV(c) (((c) >> 16) & 0x03) -unsigned int cpufreq_get (unsigned int cpu) /* in kHz */ -{ - return fclkfreq_get ()/1000; -} -EXPORT_SYMBOL(cpufreq_get); - unsigned int fclkfreq_get (void) { unsigned int clkset = CSC_CLKSET; diff --git a/arch/arm/mach-nomadik/board-nhk8815.c b/arch/arm/mach-nomadik/board-nhk8815.c index 116394484e71..9438bf6613a3 100644 --- a/arch/arm/mach-nomadik/board-nhk8815.c +++ b/arch/arm/mach-nomadik/board-nhk8815.c @@ -18,6 +18,7 @@ #include <linux/gpio.h> #include <linux/mtd/mtd.h> #include <linux/mtd/nand.h> +#include <linux/mtd/onenand.h> #include <linux/mtd/partitions.h> #include <linux/io.h> #include <asm/sizes.h> @@ -149,7 +150,7 @@ static struct mtd_partition nhk8815_onenand_partitions[] = { } }; -static struct flash_platform_data nhk8815_onenand_data = { +static struct onenand_platform_data nhk8815_onenand_data = { .parts = nhk8815_onenand_partitions, .nr_parts = ARRAY_SIZE(nhk8815_onenand_partitions), }; @@ -163,7 +164,7 @@ static struct resource nhk8815_onenand_resource[] = { }; static struct platform_device nhk8815_onenand_device = { - .name = "onenand", + .name = "onenand-flash", .id = -1, .dev = { .platform_data = &nhk8815_onenand_data, @@ -174,10 +175,10 @@ static struct platform_device nhk8815_onenand_device = { static void __init nhk8815_onenand_init(void) { -#ifdef CONFIG_ONENAND +#ifdef CONFIG_MTD_ONENAND /* Set up SMCS0 for OneNand */ - writel(0x000030db, FSMC_BCR0); - writel(0x02100551, FSMC_BTR0); + writel(0x000030db, FSMC_BCR(0)); + writel(0x02100551, FSMC_BTR(0)); #endif } diff --git a/arch/arm/mach-ns9xxx/irq.c b/arch/arm/mach-ns9xxx/irq.c index feb0e54a91de..038f24d47023 100644 --- a/arch/arm/mach-ns9xxx/irq.c +++ b/arch/arm/mach-ns9xxx/irq.c @@ -66,7 +66,7 @@ static void handle_prio_irq(unsigned int irq, struct irq_desc *desc) struct irqaction *action; irqreturn_t action_ret; - spin_lock(&desc->lock); + raw_spin_lock(&desc->lock); BUG_ON(desc->status & IRQ_INPROGRESS); @@ -78,7 +78,7 @@ static void handle_prio_irq(unsigned int irq, struct irq_desc *desc) goto out_mask; desc->status |= IRQ_INPROGRESS; - spin_unlock(&desc->lock); + raw_spin_unlock(&desc->lock); action_ret = handle_IRQ_event(irq, action); @@ -87,7 +87,7 @@ static void handle_prio_irq(unsigned int irq, struct irq_desc *desc) * Maybe this function should go to kernel/irq/chip.c? */ note_interrupt(irq, desc, action_ret); - spin_lock(&desc->lock); + raw_spin_lock(&desc->lock); desc->status &= ~IRQ_INPROGRESS; if (desc->status & IRQ_DISABLED) @@ -97,7 +97,7 @@ out_mask: /* ack unconditionally to unmask lower prio irqs */ desc->chip->ack(irq); - spin_unlock(&desc->lock); + raw_spin_unlock(&desc->lock); } #define handle_irq handle_prio_irq #endif diff --git a/arch/arm/mach-omap2/board-2430sdp.c b/arch/arm/mach-omap2/board-2430sdp.c index db9374bc528b..e508904fb67e 100644 --- a/arch/arm/mach-omap2/board-2430sdp.c +++ b/arch/arm/mach-omap2/board-2430sdp.c @@ -19,7 +19,7 @@ #include <linux/mtd/mtd.h> #include <linux/mtd/partitions.h> #include <linux/delay.h> -#include <linux/i2c/twl4030.h> +#include <linux/i2c/twl.h> #include <linux/err.h> #include <linux/clk.h> #include <linux/io.h> diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c index 4cfb7b68dfad..c90b0d0b1927 100644 --- a/arch/arm/mach-omap2/board-3430sdp.c +++ b/arch/arm/mach-omap2/board-3430sdp.c @@ -20,7 +20,7 @@ #include <linux/input/matrix_keypad.h> #include <linux/spi/spi.h> #include <linux/spi/ads7846.h> -#include <linux/i2c/twl4030.h> +#include <linux/i2c/twl.h> #include <linux/regulator/machine.h> #include <linux/io.h> #include <linux/gpio.h> diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c index 37431738f1c2..995d4a2b2dfd 100644 --- a/arch/arm/mach-omap2/board-ldp.c +++ b/arch/arm/mach-omap2/board-ldp.c @@ -24,7 +24,7 @@ #include <linux/spi/spi.h> #include <linux/spi/ads7846.h> #include <linux/regulator/machine.h> -#include <linux/i2c/twl4030.h> +#include <linux/i2c/twl.h> #include <linux/io.h> #include <linux/smsc911x.h> diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c index 6ada8029f9a8..231cb4ec1847 100644 --- a/arch/arm/mach-omap2/board-omap3beagle.c +++ b/arch/arm/mach-omap2/board-omap3beagle.c @@ -29,7 +29,7 @@ #include <linux/mtd/nand.h> #include <linux/regulator/machine.h> -#include <linux/i2c/twl4030.h> +#include <linux/i2c/twl.h> #include <mach/hardware.h> #include <asm/mach-types.h> diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c index 6f6c601eeab7..ef17cf1ab6d7 100644 --- a/arch/arm/mach-omap2/board-omap3pandora.c +++ b/arch/arm/mach-omap2/board-omap3pandora.c @@ -24,7 +24,7 @@ #include <linux/spi/spi.h> #include <linux/spi/ads7846.h> #include <linux/regulator/machine.h> -#include <linux/i2c/twl4030.h> +#include <linux/i2c/twl.h> #include <linux/leds.h> #include <linux/input.h> #include <linux/input/matrix_keypad.h> diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c index 5b78a87217e0..d192dd98a591 100644 --- a/arch/arm/mach-omap2/board-overo.c +++ b/arch/arm/mach-omap2/board-overo.c @@ -26,7 +26,7 @@ #include <linux/io.h> #include <linux/kernel.h> #include <linux/platform_device.h> -#include <linux/i2c/twl4030.h> +#include <linux/i2c/twl.h> #include <linux/regulator/machine.h> #include <linux/mtd/mtd.h> diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c index bf26ad31f9ba..17f3c91231db 100644 --- a/arch/arm/mach-omap2/board-rx51-peripherals.c +++ b/arch/arm/mach-omap2/board-rx51-peripherals.c @@ -402,15 +402,9 @@ static struct twl4030_usb_data rx51_usb_data = { static struct twl4030_ins sleep_on_seq[] __initdata = { /* - * Turn off VDD1 and VDD2. + * Turn off everything */ - {MSG_SINGULAR(DEV_GRP_P1, 0xf, RES_STATE_OFF), 4}, - {MSG_SINGULAR(DEV_GRP_P1, 0x10, RES_STATE_OFF), 2}, -/* - * And also turn off the OMAP3 PLLs and the sysclk output. - */ - {MSG_SINGULAR(DEV_GRP_P1, 0x7, RES_STATE_OFF), 3}, - {MSG_SINGULAR(DEV_GRP_P1, 0x17, RES_STATE_OFF), 3}, + {MSG_BROADCAST(DEV_GRP_NULL, RES_GRP_ALL, 1, 0, RES_STATE_SLEEP), 2}, }; static struct twl4030_script sleep_on_script __initdata = { @@ -421,14 +415,9 @@ static struct twl4030_script sleep_on_script __initdata = { static struct twl4030_ins wakeup_seq[] __initdata = { /* - * Reenable the OMAP3 PLLs. - * Wakeup VDD1 and VDD2. - * Reenable sysclk output. + * Reenable everything */ - {MSG_SINGULAR(DEV_GRP_P1, 0x7, RES_STATE_ACTIVE), 0x30}, - {MSG_SINGULAR(DEV_GRP_P1, 0xf, RES_STATE_ACTIVE), 0x30}, - {MSG_SINGULAR(DEV_GRP_P1, 0x10, RES_STATE_ACTIVE), 0x37}, - {MSG_SINGULAR(DEV_GRP_P1, 0x19, RES_STATE_ACTIVE), 3}, + {MSG_BROADCAST(DEV_GRP_NULL, RES_GRP_ALL, 1, 0, RES_STATE_ACTIVE), 2}, }; static struct twl4030_script wakeup_script __initdata = { @@ -439,10 +428,9 @@ static struct twl4030_script wakeup_script __initdata = { static struct twl4030_ins wakeup_p3_seq[] __initdata = { /* - * Wakeup VDD1 (dummy to be able to insert a delay) - * Enable CLKEN + * Reenable everything */ - {MSG_SINGULAR(DEV_GRP_P1, 0x17, RES_STATE_ACTIVE), 3}, + {MSG_BROADCAST(DEV_GRP_NULL, RES_GRP_ALL, 1, 0, RES_STATE_ACTIVE), 2}, }; static struct twl4030_script wakeup_p3_script __initdata = { @@ -463,12 +451,11 @@ static struct twl4030_ins wrst_seq[] __initdata = { {MSG_SINGULAR(DEV_GRP_NULL, RES_RESET, RES_STATE_OFF), 2}, {MSG_BROADCAST(DEV_GRP_NULL, RES_GRP_ALL, 0, 1, RES_STATE_ACTIVE), 0x13}, - {MSG_BROADCAST(DEV_GRP_NULL, RES_GRP_PP, 0, 2, RES_STATE_WRST), 0x13}, {MSG_BROADCAST(DEV_GRP_NULL, RES_GRP_PP, 0, 3, RES_STATE_OFF), 0x13}, {MSG_SINGULAR(DEV_GRP_NULL, RES_VDD1, RES_STATE_WRST), 0x13}, {MSG_SINGULAR(DEV_GRP_NULL, RES_VDD2, RES_STATE_WRST), 0x13}, {MSG_SINGULAR(DEV_GRP_NULL, RES_VPLL1, RES_STATE_WRST), 0x35}, - {MSG_SINGULAR(DEV_GRP_P1, RES_HFCLKOUT, RES_STATE_ACTIVE), 2}, + {MSG_SINGULAR(DEV_GRP_P3, RES_HFCLKOUT, RES_STATE_ACTIVE), 2}, {MSG_SINGULAR(DEV_GRP_NULL, RES_RESET, RES_STATE_ACTIVE), 2}, }; @@ -490,22 +477,81 @@ static struct twl4030_script *twl4030_scripts[] __initdata = { }; static struct twl4030_resconfig twl4030_rconfig[] __initdata = { - { .resource = RES_VINTANA1, .devgroup = -1, .type = -1, .type2 = 1 }, - { .resource = RES_VINTANA2, .devgroup = -1, .type = -1, .type2 = 1 }, - { .resource = RES_VINTDIG, .devgroup = -1, .type = -1, .type2 = 1 }, - { .resource = RES_VMMC1, .devgroup = -1, .type = -1, .type2 = 3}, - { .resource = RES_VMMC2, .devgroup = DEV_GRP_NULL, .type = -1, - .type2 = 3}, - { .resource = RES_VAUX1, .devgroup = -1, .type = -1, .type2 = 3}, - { .resource = RES_VAUX2, .devgroup = -1, .type = -1, .type2 = 3}, - { .resource = RES_VAUX3, .devgroup = -1, .type = -1, .type2 = 3}, - { .resource = RES_VAUX4, .devgroup = -1, .type = -1, .type2 = 3}, - { .resource = RES_VPLL2, .devgroup = -1, .type = -1, .type2 = 3}, - { .resource = RES_VDAC, .devgroup = -1, .type = -1, .type2 = 3}, - { .resource = RES_VSIM, .devgroup = DEV_GRP_NULL, .type = -1, - .type2 = 3}, - { .resource = RES_CLKEN, .devgroup = DEV_GRP_P3, .type = -1, - .type2 = 1 }, + { .resource = RES_VDD1, .devgroup = -1, + .type = 1, .type2 = -1, .remap_off = RES_STATE_OFF, + .remap_sleep = RES_STATE_OFF + }, + { .resource = RES_VDD2, .devgroup = -1, + .type = 1, .type2 = -1, .remap_off = RES_STATE_OFF, + .remap_sleep = RES_STATE_OFF + }, + { .resource = RES_VPLL1, .devgroup = -1, + .type = 1, .type2 = -1, .remap_off = RES_STATE_OFF, + .remap_sleep = RES_STATE_OFF + }, + { .resource = RES_VPLL2, .devgroup = -1, + .type = -1, .type2 = 3, .remap_off = -1, .remap_sleep = -1 + }, + { .resource = RES_VAUX1, .devgroup = -1, + .type = -1, .type2 = 3, .remap_off = -1, .remap_sleep = -1 + }, + { .resource = RES_VAUX2, .devgroup = -1, + .type = -1, .type2 = 3, .remap_off = -1, .remap_sleep = -1 + }, + { .resource = RES_VAUX3, .devgroup = -1, + .type = -1, .type2 = 3, .remap_off = -1, .remap_sleep = -1 + }, + { .resource = RES_VAUX4, .devgroup = -1, + .type = -1, .type2 = 3, .remap_off = -1, .remap_sleep = -1 + }, + { .resource = RES_VMMC1, .devgroup = -1, + .type = -1, .type2 = 3, .remap_off = -1, .remap_sleep = -1 + }, + { .resource = RES_VMMC2, .devgroup = -1, + .type = -1, .type2 = 3, .remap_off = -1, .remap_sleep = -1 + }, + { .resource = RES_VDAC, .devgroup = -1, + .type = -1, .type2 = 3, .remap_off = -1, .remap_sleep = -1 + }, + { .resource = RES_VSIM, .devgroup = -1, + .type = -1, .type2 = 3, .remap_off = -1, .remap_sleep = -1 + }, + { .resource = RES_VINTANA1, .devgroup = DEV_GRP_P1 | DEV_GRP_P3, + .type = -1, .type2 = -1, .remap_off = -1, .remap_sleep = -1 + }, + { .resource = RES_VINTANA2, .devgroup = DEV_GRP_P1 | DEV_GRP_P3, + .type = 1, .type2 = -1, .remap_off = -1, .remap_sleep = -1 + }, + { .resource = RES_VINTDIG, .devgroup = DEV_GRP_P1 | DEV_GRP_P3, + .type = -1, .type2 = -1, .remap_off = -1, .remap_sleep = -1 + }, + { .resource = RES_VIO, .devgroup = DEV_GRP_P3, + .type = 1, .type2 = -1, .remap_off = -1, .remap_sleep = -1 + }, + { .resource = RES_CLKEN, .devgroup = DEV_GRP_P1 | DEV_GRP_P3, + .type = 1, .type2 = -1 , .remap_off = -1, .remap_sleep = -1 + }, + { .resource = RES_REGEN, .devgroup = DEV_GRP_P1 | DEV_GRP_P3, + .type = 1, .type2 = -1, .remap_off = -1, .remap_sleep = -1 + }, + { .resource = RES_NRES_PWRON, .devgroup = DEV_GRP_P1 | DEV_GRP_P3, + .type = 1, .type2 = -1, .remap_off = -1, .remap_sleep = -1 + }, + { .resource = RES_SYSEN, .devgroup = DEV_GRP_P1 | DEV_GRP_P3, + .type = 1, .type2 = -1, .remap_off = -1, .remap_sleep = -1 + }, + { .resource = RES_HFCLKOUT, .devgroup = DEV_GRP_P3, + .type = 1, .type2 = -1, .remap_off = -1, .remap_sleep = -1 + }, + { .resource = RES_32KCLKOUT, .devgroup = -1, + .type = 1, .type2 = -1, .remap_off = -1, .remap_sleep = -1 + }, + { .resource = RES_RESET, .devgroup = -1, + .type = 1, .type2 = -1, .remap_off = -1, .remap_sleep = -1 + }, + { .resource = RES_Main_Ref, .devgroup = -1, + .type = 1, .type2 = -1, .remap_off = -1, .remap_sleep = -1 + }, { 0, 0}, }; diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig index d89c6adbe8bc..e6d8e10ae5d1 100644 --- a/arch/arm/mach-pxa/Kconfig +++ b/arch/arm/mach-pxa/Kconfig @@ -63,6 +63,15 @@ config ARCH_VIPER select HAVE_PWM select PXA_HAVE_BOARD_IRQS select PXA_HAVE_ISA_IRQS + select ARCOM_PCMCIA + +config MACH_ARCOM_ZEUS + bool "Arcom/Eurotech ZEUS SBC" + select PXA27x + select ISA + select PXA_HAVE_BOARD_IRQS + select PXA_HAVE_ISA_IRQS + select ARCOM_PCMCIA config MACH_BALLOON3 bool "Balloon 3 board" @@ -179,6 +188,11 @@ config MACH_TRIZEPS_ANY endchoice +config ARCOM_PCMCIA + bool + help + Generic option for Arcom Viper/Zeus PCMCIA + config TRIZEPS_PCMCIA bool help diff --git a/arch/arm/mach-pxa/Makefile b/arch/arm/mach-pxa/Makefile index b5d29e60a341..f64afda7e6f6 100644 --- a/arch/arm/mach-pxa/Makefile +++ b/arch/arm/mach-pxa/Makefile @@ -38,6 +38,7 @@ obj-$(CONFIG_MACH_SAAR) += saar.o # 3rd Party Dev Platforms obj-$(CONFIG_ARCH_PXA_IDP) += idp.o obj-$(CONFIG_ARCH_VIPER) += viper.o +obj-$(CONFIG_MACH_ARCOM_ZEUS) += zeus.o obj-$(CONFIG_MACH_BALLOON3) += balloon3.o obj-$(CONFIG_MACH_CSB726) += csb726.o obj-$(CONFIG_CSB726_CSB701) += csb701.o diff --git a/arch/arm/mach-pxa/em-x270.c b/arch/arm/mach-pxa/em-x270.c index 1c0de808b54d..c8a01bc85fde 100644 --- a/arch/arm/mach-pxa/em-x270.c +++ b/arch/arm/mach-pxa/em-x270.c @@ -497,16 +497,15 @@ static int em_x270_usb_hub_init(void) goto err_free_vbus_gpio; /* USB Hub power-on and reset */ - gpio_direction_output(usb_hub_reset, 0); + gpio_direction_output(usb_hub_reset, 1); + gpio_direction_output(GPIO9_USB_VBUS_EN, 0); regulator_enable(em_x270_usb_ldo); - gpio_set_value(usb_hub_reset, 1); gpio_set_value(usb_hub_reset, 0); + gpio_set_value(usb_hub_reset, 1); regulator_disable(em_x270_usb_ldo); regulator_enable(em_x270_usb_ldo); - gpio_set_value(usb_hub_reset, 1); - - /* enable VBUS */ - gpio_direction_output(GPIO9_USB_VBUS_EN, 1); + gpio_set_value(usb_hub_reset, 0); + gpio_set_value(GPIO9_USB_VBUS_EN, 1); return 0; diff --git a/arch/arm/mach-pxa/include/mach/arcom-pcmcia.h b/arch/arm/mach-pxa/include/mach/arcom-pcmcia.h new file mode 100644 index 000000000000..d428be4db44c --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/arcom-pcmcia.h @@ -0,0 +1,11 @@ +#ifndef __ARCOM_PCMCIA_H +#define __ARCOM_PCMCIA_H + +struct arcom_pcmcia_pdata { + int cd_gpio; + int rdy_gpio; + int pwr_gpio; + void (*reset)(int state); +}; + +#endif diff --git a/arch/arm/mach-pxa/include/mach/viper.h b/arch/arm/mach-pxa/include/mach/viper.h index 10988c270ca3..5f5fbf1f6489 100644 --- a/arch/arm/mach-pxa/include/mach/viper.h +++ b/arch/arm/mach-pxa/include/mach/viper.h @@ -85,8 +85,6 @@ /* Interrupt and Configuration Register (VIPER_ICR) */ /* This is a write only register. Only CF_RST is used under Linux */ -extern void viper_cf_rst(int state); - #define VIPER_ICR_RETRIG (1 << 0) #define VIPER_ICR_AUTO_CLR (1 << 1) #define VIPER_ICR_R_DIS (1 << 2) diff --git a/arch/arm/mach-pxa/include/mach/zeus.h b/arch/arm/mach-pxa/include/mach/zeus.h new file mode 100644 index 000000000000..c387046d2f28 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/zeus.h @@ -0,0 +1,82 @@ +/* + * arch/arm/mach-pxa/include/mach/zeus.h + * + * Author: David Vrabel + * Created: Sept 28, 2005 + * Copyright: Arcom Control Systems Ltd. + * + * Maintained by: Marc Zyngier <maz@misterjones.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef _MACH_ZEUS_H +#define _MACH_ZEUS_H + +/* Physical addresses */ +#define ZEUS_FLASH_PHYS PXA_CS0_PHYS +#define ZEUS_ETH0_PHYS PXA_CS1_PHYS +#define ZEUS_ETH1_PHYS PXA_CS2_PHYS +#define ZEUS_CPLD_PHYS (PXA_CS4_PHYS+0x2000000) +#define ZEUS_SRAM_PHYS PXA_CS5_PHYS +#define ZEUS_PC104IO_PHYS (0x30000000) + +#define ZEUS_CPLD_VERSION_PHYS (ZEUS_CPLD_PHYS + 0x00000000) +#define ZEUS_CPLD_ISA_IRQ_PHYS (ZEUS_CPLD_PHYS + 0x00800000) +#define ZEUS_CPLD_CONTROL_PHYS (ZEUS_CPLD_PHYS + 0x01000000) +#define ZEUS_CPLD_EXTWDOG_PHYS (ZEUS_CPLD_PHYS + 0x01800000) + +/* GPIOs */ +#define ZEUS_AC97_GPIO 0 +#define ZEUS_WAKEUP_GPIO 1 +#define ZEUS_UARTA_GPIO 9 +#define ZEUS_UARTB_GPIO 10 +#define ZEUS_UARTC_GPIO 12 +#define ZEUS_UARTD_GPIO 11 +#define ZEUS_ETH0_GPIO 14 +#define ZEUS_ISA_GPIO 17 +#define ZEUS_BKLEN_GPIO 19 +#define ZEUS_USB2_PWREN_GPIO 22 +#define ZEUS_PTT_GPIO 27 +#define ZEUS_CF_CD_GPIO 35 +#define ZEUS_MMC_WP_GPIO 52 +#define ZEUS_MMC_CD_GPIO 53 +#define ZEUS_EXTGPIO_GPIO 91 +#define ZEUS_CF_PWEN_GPIO 97 +#define ZEUS_CF_RDY_GPIO 99 +#define ZEUS_LCD_EN_GPIO 101 +#define ZEUS_ETH1_GPIO 113 +#define ZEUS_CAN_GPIO 116 + +#define ZEUS_EXT0_GPIO_BASE 128 +#define ZEUS_EXT1_GPIO_BASE 160 +#define ZEUS_USER_GPIO_BASE 192 + +#define ZEUS_EXT0_GPIO(x) (ZEUS_EXT0_GPIO_BASE + (x)) +#define ZEUS_EXT1_GPIO(x) (ZEUS_EXT1_GPIO_BASE + (x)) +#define ZEUS_USER_GPIO(x) (ZEUS_USER_GPIO_BASE + (x)) + +/* + * CPLD registers: + * Only 4 registers, but spreaded over a 32MB address space. + * Be gentle, and remap that over 32kB... + */ + +#define ZEUS_CPLD (0xf0000000) +#define ZEUS_CPLD_VERSION (ZEUS_CPLD + 0x0000) +#define ZEUS_CPLD_ISA_IRQ (ZEUS_CPLD + 0x1000) +#define ZEUS_CPLD_CONTROL (ZEUS_CPLD + 0x2000) +#define ZEUS_CPLD_EXTWDOG (ZEUS_CPLD + 0x3000) + +/* CPLD register bits */ +#define ZEUS_CPLD_CONTROL_CF_RST 0x01 + +#define ZEUS_PC104IO (0xf1000000) + +#define ZEUS_SRAM_SIZE (256 * 1024) + +#endif + + diff --git a/arch/arm/mach-pxa/viper.c b/arch/arm/mach-pxa/viper.c index cf0d71b7797e..5352b4e5a7dd 100644 --- a/arch/arm/mach-pxa/viper.c +++ b/arch/arm/mach-pxa/viper.c @@ -47,6 +47,7 @@ #include <mach/pxafb.h> #include <plat/i2c.h> #include <mach/regs-uart.h> +#include <mach/arcom-pcmcia.h> #include <mach/viper.h> #include <asm/setup.h> @@ -76,14 +77,28 @@ static void viper_icr_clear_bit(unsigned int bit) } /* This function is used from the pcmcia module to reset the CF */ -void viper_cf_rst(int state) +static void viper_cf_reset(int state) { if (state) viper_icr_set_bit(VIPER_ICR_CF_RST); else viper_icr_clear_bit(VIPER_ICR_CF_RST); } -EXPORT_SYMBOL(viper_cf_rst); + +static struct arcom_pcmcia_pdata viper_pcmcia_info = { + .cd_gpio = VIPER_CF_CD_GPIO, + .rdy_gpio = VIPER_CF_RDY_GPIO, + .pwr_gpio = VIPER_CF_POWER_GPIO, + .reset = viper_cf_reset, +}; + +static struct platform_device viper_pcmcia_device = { + .name = "viper-pcmcia", + .id = -1, + .dev = { + .platform_data = &viper_pcmcia_info, + }, +}; /* * The CPLD version register was not present on VIPER boards prior to @@ -685,6 +700,7 @@ static struct platform_device *viper_devs[] __initdata = { &viper_mtd_devices[0], &viper_mtd_devices[1], &viper_backlight_device, + &viper_pcmcia_device, }; static mfp_cfg_t viper_pin_config[] __initdata = { diff --git a/arch/arm/mach-pxa/zeus.c b/arch/arm/mach-pxa/zeus.c new file mode 100644 index 000000000000..5b986a8bd9e6 --- /dev/null +++ b/arch/arm/mach-pxa/zeus.c @@ -0,0 +1,820 @@ +/* + * Support for the Arcom ZEUS. + * + * Copyright (C) 2006 Arcom Control Systems Ltd. + * + * Loosely based on Arcom's 2.6.16.28. + * Maintained by Marc Zyngier <maz@misterjones.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/cpufreq.h> +#include <linux/interrupt.h> +#include <linux/irq.h> +#include <linux/pm.h> +#include <linux/gpio.h> +#include <linux/serial_8250.h> +#include <linux/dm9000.h> +#include <linux/mmc/host.h> +#include <linux/spi/spi.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/physmap.h> +#include <linux/i2c.h> +#include <linux/i2c/pca953x.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/map.h> + +#include <plat/i2c.h> + +#include <mach/pxa2xx-regs.h> +#include <mach/regs-uart.h> +#include <mach/ohci.h> +#include <mach/mmc.h> +#include <mach/pxa27x-udc.h> +#include <mach/udc.h> +#include <mach/pxafb.h> +#include <mach/pxa2xx_spi.h> +#include <mach/mfp-pxa27x.h> +#include <mach/pm.h> +#include <mach/audio.h> +#include <mach/arcom-pcmcia.h> +#include <mach/zeus.h> + +#include "generic.h" + +/* + * Interrupt handling + */ + +static unsigned long zeus_irq_enabled_mask; +static const int zeus_isa_irqs[] = { 3, 4, 5, 6, 7, 10, 11, 12, }; +static const int zeus_isa_irq_map[] = { + 0, /* ISA irq #0, invalid */ + 0, /* ISA irq #1, invalid */ + 0, /* ISA irq #2, invalid */ + 1 << 0, /* ISA irq #3 */ + 1 << 1, /* ISA irq #4 */ + 1 << 2, /* ISA irq #5 */ + 1 << 3, /* ISA irq #6 */ + 1 << 4, /* ISA irq #7 */ + 0, /* ISA irq #8, invalid */ + 0, /* ISA irq #9, invalid */ + 1 << 5, /* ISA irq #10 */ + 1 << 6, /* ISA irq #11 */ + 1 << 7, /* ISA irq #12 */ +}; + +static inline int zeus_irq_to_bitmask(unsigned int irq) +{ + return zeus_isa_irq_map[irq - PXA_ISA_IRQ(0)]; +} + +static inline int zeus_bit_to_irq(int bit) +{ + return zeus_isa_irqs[bit] + PXA_ISA_IRQ(0); +} + +static void zeus_ack_irq(unsigned int irq) +{ + __raw_writew(zeus_irq_to_bitmask(irq), ZEUS_CPLD_ISA_IRQ); +} + +static void zeus_mask_irq(unsigned int irq) +{ + zeus_irq_enabled_mask &= ~(zeus_irq_to_bitmask(irq)); +} + +static void zeus_unmask_irq(unsigned int irq) +{ + zeus_irq_enabled_mask |= zeus_irq_to_bitmask(irq); +} + +static inline unsigned long zeus_irq_pending(void) +{ + return __raw_readw(ZEUS_CPLD_ISA_IRQ) & zeus_irq_enabled_mask; +} + +static void zeus_irq_handler(unsigned int irq, struct irq_desc *desc) +{ + unsigned long pending; + + pending = zeus_irq_pending(); + do { + /* we're in a chained irq handler, + * so ack the interrupt by hand */ + desc->chip->ack(gpio_to_irq(ZEUS_ISA_GPIO)); + + if (likely(pending)) { + irq = zeus_bit_to_irq(__ffs(pending)); + generic_handle_irq(irq); + } + pending = zeus_irq_pending(); + } while (pending); +} + +static struct irq_chip zeus_irq_chip = { + .name = "ISA", + .ack = zeus_ack_irq, + .mask = zeus_mask_irq, + .unmask = zeus_unmask_irq, +}; + +static void __init zeus_init_irq(void) +{ + int level; + int isa_irq; + + pxa27x_init_irq(); + + /* Peripheral IRQs. It would be nice to move those inside driver + configuration, but it is not supported at the moment. */ + set_irq_type(gpio_to_irq(ZEUS_AC97_GPIO), IRQ_TYPE_EDGE_RISING); + set_irq_type(gpio_to_irq(ZEUS_WAKEUP_GPIO), IRQ_TYPE_EDGE_RISING); + set_irq_type(gpio_to_irq(ZEUS_PTT_GPIO), IRQ_TYPE_EDGE_RISING); + set_irq_type(gpio_to_irq(ZEUS_EXTGPIO_GPIO), IRQ_TYPE_EDGE_FALLING); + set_irq_type(gpio_to_irq(ZEUS_CAN_GPIO), IRQ_TYPE_EDGE_FALLING); + + /* Setup ISA IRQs */ + for (level = 0; level < ARRAY_SIZE(zeus_isa_irqs); level++) { + isa_irq = zeus_bit_to_irq(level); + set_irq_chip(isa_irq, &zeus_irq_chip); + set_irq_handler(isa_irq, handle_edge_irq); + set_irq_flags(isa_irq, IRQF_VALID | IRQF_PROBE); + } + + set_irq_type(gpio_to_irq(ZEUS_ISA_GPIO), IRQ_TYPE_EDGE_RISING); + set_irq_chained_handler(gpio_to_irq(ZEUS_ISA_GPIO), zeus_irq_handler); +} + + +/* + * Platform devices + */ + +/* Flash */ +static struct resource zeus_mtd_resources[] = { + [0] = { /* NOR Flash (up to 64MB) */ + .start = ZEUS_FLASH_PHYS, + .end = ZEUS_FLASH_PHYS + SZ_64M - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { /* SRAM */ + .start = ZEUS_SRAM_PHYS, + .end = ZEUS_SRAM_PHYS + SZ_512K - 1, + .flags = IORESOURCE_MEM, + }, +}; + +static struct physmap_flash_data zeus_flash_data[] = { + [0] = { + .width = 2, + .parts = NULL, + .nr_parts = 0, + }, +}; + +static struct platform_device zeus_mtd_devices[] = { + [0] = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = &zeus_flash_data[0], + }, + .resource = &zeus_mtd_resources[0], + .num_resources = 1, + }, +}; + +/* Serial */ +static struct resource zeus_serial_resources[] = { + { + .start = 0x10000000, + .end = 0x1000000f, + .flags = IORESOURCE_MEM, + }, + { + .start = 0x10800000, + .end = 0x1080000f, + .flags = IORESOURCE_MEM, + }, + { + .start = 0x11000000, + .end = 0x1100000f, + .flags = IORESOURCE_MEM, + }, + { + .start = 0x40100000, + .end = 0x4010001f, + .flags = IORESOURCE_MEM, + }, + { + .start = 0x40200000, + .end = 0x4020001f, + .flags = IORESOURCE_MEM, + }, + { + .start = 0x40700000, + .end = 0x4070001f, + .flags = IORESOURCE_MEM, + }, +}; + +static struct plat_serial8250_port serial_platform_data[] = { + /* External UARTs */ + /* FIXME: Shared IRQs on COM1-COM4 will not work properly on v1i1 hardware. */ + { /* COM1 */ + .mapbase = 0x10000000, + .irq = gpio_to_irq(ZEUS_UARTA_GPIO), + .irqflags = IRQF_TRIGGER_RISING, + .uartclk = 14745600, + .regshift = 1, + .flags = UPF_IOREMAP | UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .iotype = UPIO_MEM, + }, + { /* COM2 */ + .mapbase = 0x10800000, + .irq = gpio_to_irq(ZEUS_UARTB_GPIO), + .irqflags = IRQF_TRIGGER_RISING, + .uartclk = 14745600, + .regshift = 1, + .flags = UPF_IOREMAP | UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .iotype = UPIO_MEM, + }, + { /* COM3 */ + .mapbase = 0x11000000, + .irq = gpio_to_irq(ZEUS_UARTC_GPIO), + .irqflags = IRQF_TRIGGER_RISING, + .uartclk = 14745600, + .regshift = 1, + .flags = UPF_IOREMAP | UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .iotype = UPIO_MEM, + }, + { /* COM4 */ + .mapbase = 0x11800000, + .irq = gpio_to_irq(ZEUS_UARTD_GPIO), + .irqflags = IRQF_TRIGGER_RISING, + .uartclk = 14745600, + .regshift = 1, + .flags = UPF_IOREMAP | UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .iotype = UPIO_MEM, + }, + /* Internal UARTs */ + { /* FFUART */ + .membase = (void *)&FFUART, + .mapbase = __PREG(FFUART), + .irq = IRQ_FFUART, + .uartclk = 921600 * 16, + .regshift = 2, + .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .iotype = UPIO_MEM, + }, + { /* BTUART */ + .membase = (void *)&BTUART, + .mapbase = __PREG(BTUART), + .irq = IRQ_BTUART, + .uartclk = 921600 * 16, + .regshift = 2, + .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .iotype = UPIO_MEM, + }, + { /* STUART */ + .membase = (void *)&STUART, + .mapbase = __PREG(STUART), + .irq = IRQ_STUART, + .uartclk = 921600 * 16, + .regshift = 2, + .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .iotype = UPIO_MEM, + }, + { }, +}; + +static struct platform_device zeus_serial_device = { + .name = "serial8250", + .id = PLAT8250_DEV_PLATFORM, + .dev = { + .platform_data = serial_platform_data, + }, + .num_resources = ARRAY_SIZE(zeus_serial_resources), + .resource = zeus_serial_resources, +}; + +/* Ethernet */ +static struct resource zeus_dm9k0_resource[] = { + [0] = { + .start = ZEUS_ETH0_PHYS, + .end = ZEUS_ETH0_PHYS + 1, + .flags = IORESOURCE_MEM + }, + [1] = { + .start = ZEUS_ETH0_PHYS + 2, + .end = ZEUS_ETH0_PHYS + 3, + .flags = IORESOURCE_MEM + }, + [2] = { + .start = gpio_to_irq(ZEUS_ETH0_GPIO), + .end = gpio_to_irq(ZEUS_ETH0_GPIO), + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE, + }, +}; + +static struct resource zeus_dm9k1_resource[] = { + [0] = { + .start = ZEUS_ETH1_PHYS, + .end = ZEUS_ETH1_PHYS + 1, + .flags = IORESOURCE_MEM + }, + [1] = { + .start = ZEUS_ETH1_PHYS + 2, + .end = ZEUS_ETH1_PHYS + 3, + .flags = IORESOURCE_MEM, + }, + [2] = { + .start = gpio_to_irq(ZEUS_ETH1_GPIO), + .end = gpio_to_irq(ZEUS_ETH1_GPIO), + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE, + }, +}; + +static struct dm9000_plat_data zeus_dm9k_platdata = { + .flags = DM9000_PLATF_16BITONLY, +}; + +static struct platform_device zeus_dm9k0_device = { + .name = "dm9000", + .id = 0, + .num_resources = ARRAY_SIZE(zeus_dm9k0_resource), + .resource = zeus_dm9k0_resource, + .dev = { + .platform_data = &zeus_dm9k_platdata, + } +}; + +static struct platform_device zeus_dm9k1_device = { + .name = "dm9000", + .id = 1, + .num_resources = ARRAY_SIZE(zeus_dm9k1_resource), + .resource = zeus_dm9k1_resource, + .dev = { + .platform_data = &zeus_dm9k_platdata, + } +}; + +/* External SRAM */ +static struct resource zeus_sram_resource = { + .start = ZEUS_SRAM_PHYS, + .end = ZEUS_SRAM_PHYS + ZEUS_SRAM_SIZE * 2 - 1, + .flags = IORESOURCE_MEM, +}; + +static struct platform_device zeus_sram_device = { + .name = "pxa2xx-8bit-sram", + .id = 0, + .num_resources = 1, + .resource = &zeus_sram_resource, +}; + +/* SPI interface on SSP3 */ +static struct pxa2xx_spi_master pxa2xx_spi_ssp3_master_info = { + .num_chipselect = 1, + .enable_dma = 1, +}; + +static struct platform_device pxa2xx_spi_ssp3_device = { + .name = "pxa2xx-spi", + .id = 3, + .dev = { + .platform_data = &pxa2xx_spi_ssp3_master_info, + }, +}; + +/* Leds */ +static struct gpio_led zeus_leds[] = { + [0] = { + .name = "zeus:yellow:1", + .default_trigger = "heartbeat", + .gpio = ZEUS_EXT0_GPIO(3), + .active_low = 1, + }, + [1] = { + .name = "zeus:yellow:2", + .default_trigger = "default-on", + .gpio = ZEUS_EXT0_GPIO(4), + .active_low = 1, + }, + [2] = { + .name = "zeus:yellow:3", + .default_trigger = "default-on", + .gpio = ZEUS_EXT0_GPIO(5), + .active_low = 1, + }, +}; + +static struct gpio_led_platform_data zeus_leds_info = { + .leds = zeus_leds, + .num_leds = ARRAY_SIZE(zeus_leds), +}; + +static struct platform_device zeus_leds_device = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &zeus_leds_info, + }, +}; + +static void zeus_cf_reset(int state) +{ + u16 cpld_state = __raw_readw(ZEUS_CPLD_CONTROL); + + if (state) + cpld_state |= ZEUS_CPLD_CONTROL_CF_RST; + else + cpld_state &= ~ZEUS_CPLD_CONTROL_CF_RST; + + __raw_writew(cpld_state, ZEUS_CPLD_CONTROL); +} + +static struct arcom_pcmcia_pdata zeus_pcmcia_info = { + .cd_gpio = ZEUS_CF_CD_GPIO, + .rdy_gpio = ZEUS_CF_RDY_GPIO, + .pwr_gpio = ZEUS_CF_PWEN_GPIO, + .reset = zeus_cf_reset, +}; + +static struct platform_device zeus_pcmcia_device = { + .name = "zeus-pcmcia", + .id = -1, + .dev = { + .platform_data = &zeus_pcmcia_info, + }, +}; + +static struct platform_device *zeus_devices[] __initdata = { + &zeus_serial_device, + &zeus_mtd_devices[0], + &zeus_dm9k0_device, + &zeus_dm9k1_device, + &zeus_sram_device, + &pxa2xx_spi_ssp3_device, + &zeus_leds_device, + &zeus_pcmcia_device, +}; + +/* AC'97 */ +static pxa2xx_audio_ops_t zeus_ac97_info = { + .reset_gpio = 95, +}; + + +/* + * USB host + */ + +static int zeus_ohci_init(struct device *dev) +{ + int err; + + /* Switch on port 2. */ + if ((err = gpio_request(ZEUS_USB2_PWREN_GPIO, "USB2_PWREN"))) { + dev_err(dev, "Can't request USB2_PWREN\n"); + return err; + } + + if ((err = gpio_direction_output(ZEUS_USB2_PWREN_GPIO, 1))) { + gpio_free(ZEUS_USB2_PWREN_GPIO); + dev_err(dev, "Can't enable USB2_PWREN\n"); + return err; + } + + /* Port 2 is shared between host and client interface. */ + UP2OCR = UP2OCR_HXOE | UP2OCR_HXS | UP2OCR_DMPDE | UP2OCR_DPPDE; + + return 0; +} + +static void zeus_ohci_exit(struct device *dev) +{ + /* Power-off port 2 */ + gpio_direction_output(ZEUS_USB2_PWREN_GPIO, 0); + gpio_free(ZEUS_USB2_PWREN_GPIO); +} + +static struct pxaohci_platform_data zeus_ohci_platform_data = { + .port_mode = PMM_NPS_MODE, + .flags = ENABLE_PORT_ALL | POWER_CONTROL_LOW | POWER_SENSE_LOW, + .init = zeus_ohci_init, + .exit = zeus_ohci_exit, +}; + +/* + * Flat Panel + */ + +static void zeus_lcd_power(int on, struct fb_var_screeninfo *si) +{ + gpio_set_value(ZEUS_LCD_EN_GPIO, on); +} + +static void zeus_backlight_power(int on) +{ + gpio_set_value(ZEUS_BKLEN_GPIO, on); +} + +static int zeus_setup_fb_gpios(void) +{ + int err; + + if ((err = gpio_request(ZEUS_LCD_EN_GPIO, "LCD_EN"))) + goto out_err; + + if ((err = gpio_direction_output(ZEUS_LCD_EN_GPIO, 0))) + goto out_err_lcd; + + if ((err = gpio_request(ZEUS_BKLEN_GPIO, "BKLEN"))) + goto out_err_lcd; + + if ((err = gpio_direction_output(ZEUS_BKLEN_GPIO, 0))) + goto out_err_bkl; + + return 0; + +out_err_bkl: + gpio_free(ZEUS_BKLEN_GPIO); +out_err_lcd: + gpio_free(ZEUS_LCD_EN_GPIO); +out_err: + return err; +} + +static struct pxafb_mode_info zeus_fb_mode_info[] = { + { + .pixclock = 39722, + + .xres = 640, + .yres = 480, + + .bpp = 16, + + .hsync_len = 63, + .left_margin = 16, + .right_margin = 81, + + .vsync_len = 2, + .upper_margin = 12, + .lower_margin = 31, + + .sync = 0, + }, +}; + +static struct pxafb_mach_info zeus_fb_info = { + .modes = zeus_fb_mode_info, + .num_modes = 1, + .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL, + .pxafb_lcd_power = zeus_lcd_power, + .pxafb_backlight_power = zeus_backlight_power, +}; + +/* + * MMC/SD Device + * + * The card detect interrupt isn't debounced so we delay it by 250ms + * to give the card a chance to fully insert/eject. + */ + +static struct pxamci_platform_data zeus_mci_platform_data = { + .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34, + .detect_delay = HZ/4, + .gpio_card_detect = ZEUS_MMC_CD_GPIO, + .gpio_card_ro = ZEUS_MMC_WP_GPIO, + .gpio_card_ro_invert = 1, + .gpio_power = -1 +}; + +/* + * USB Device Controller + */ +static void zeus_udc_command(int cmd) +{ + switch (cmd) { + case PXA2XX_UDC_CMD_DISCONNECT: + pr_info("zeus: disconnecting USB client\n"); + UP2OCR = UP2OCR_HXOE | UP2OCR_HXS | UP2OCR_DMPDE | UP2OCR_DPPDE; + break; + + case PXA2XX_UDC_CMD_CONNECT: + pr_info("zeus: connecting USB client\n"); + UP2OCR = UP2OCR_HXOE | UP2OCR_DPPUE; + break; + } +} + +static struct pxa2xx_udc_mach_info zeus_udc_info = { + .udc_command = zeus_udc_command, +}; + +static void zeus_power_off(void) +{ + local_irq_disable(); + pxa27x_cpu_suspend(PWRMODE_DEEPSLEEP); +} + +int zeus_get_pcb_info(struct i2c_client *client, unsigned gpio, + unsigned ngpio, void *context) +{ + int i; + u8 pcb_info = 0; + + for (i = 0; i < 8; i++) { + int pcb_bit = gpio + i + 8; + + if (gpio_request(pcb_bit, "pcb info")) { + dev_err(&client->dev, "Can't request pcb info %d\n", i); + continue; + } + + if (gpio_direction_input(pcb_bit)) { + dev_err(&client->dev, "Can't read pcb info %d\n", i); + gpio_free(pcb_bit); + continue; + } + + pcb_info |= !!gpio_get_value(pcb_bit) << i; + + gpio_free(pcb_bit); + } + + dev_info(&client->dev, "Zeus PCB version %d issue %d\n", + pcb_info >> 4, pcb_info & 0xf); + + return 0; +} + +static struct pca953x_platform_data zeus_pca953x_pdata[] = { + [0] = { .gpio_base = ZEUS_EXT0_GPIO_BASE, }, + [1] = { + .gpio_base = ZEUS_EXT1_GPIO_BASE, + .setup = zeus_get_pcb_info, + }, + [2] = { .gpio_base = ZEUS_USER_GPIO_BASE, }, +}; + +static struct i2c_board_info __initdata zeus_i2c_devices[] = { + { + I2C_BOARD_INFO("pca9535", 0x21), + .platform_data = &zeus_pca953x_pdata[0], + }, + { + I2C_BOARD_INFO("pca9535", 0x22), + .platform_data = &zeus_pca953x_pdata[1], + }, + { + I2C_BOARD_INFO("pca9535", 0x20), + .platform_data = &zeus_pca953x_pdata[2], + .irq = gpio_to_irq(ZEUS_EXTGPIO_GPIO), + }, + { I2C_BOARD_INFO("lm75a", 0x48) }, + { I2C_BOARD_INFO("24c01", 0x50) }, + { I2C_BOARD_INFO("isl1208", 0x6f) }, +}; + +static mfp_cfg_t zeus_pin_config[] __initdata = { + GPIO15_nCS_1, + GPIO78_nCS_2, + GPIO80_nCS_4, + GPIO33_nCS_5, + + GPIO22_GPIO, + GPIO32_MMC_CLK, + GPIO92_MMC_DAT_0, + GPIO109_MMC_DAT_1, + GPIO110_MMC_DAT_2, + GPIO111_MMC_DAT_3, + GPIO112_MMC_CMD, + + GPIO88_USBH1_PWR, + GPIO89_USBH1_PEN, + GPIO119_USBH2_PWR, + GPIO120_USBH2_PEN, + + GPIO86_LCD_LDD_16, + GPIO87_LCD_LDD_17, + + GPIO102_GPIO, + GPIO104_CIF_DD_2, + GPIO105_CIF_DD_1, + + GPIO48_nPOE, + GPIO49_nPWE, + GPIO50_nPIOR, + GPIO51_nPIOW, + GPIO85_nPCE_1, + GPIO54_nPCE_2, + GPIO79_PSKTSEL, + GPIO55_nPREG, + GPIO56_nPWAIT, + GPIO57_nIOIS16, + GPIO36_GPIO, /* CF CD */ + GPIO97_GPIO, /* CF PWREN */ + GPIO99_GPIO, /* CF RDY */ +}; + +static void __init zeus_init(void) +{ + u16 dm9000_msc = 0xe279; + + system_rev = __raw_readw(ZEUS_CPLD_VERSION); + pr_info("Zeus CPLD V%dI%d\n", (system_rev & 0xf0) >> 4, (system_rev & 0x0f)); + + /* Fix timings for dm9000s (CS1/CS2)*/ + MSC0 = (MSC0 & 0xffff) | (dm9000_msc << 16); + MSC1 = (MSC1 & 0xffff0000) | dm9000_msc; + + pm_power_off = zeus_power_off; + + pxa2xx_mfp_config(ARRAY_AND_SIZE(zeus_pin_config)); + + platform_add_devices(zeus_devices, ARRAY_SIZE(zeus_devices)); + + pxa_set_ohci_info(&zeus_ohci_platform_data); + + if (zeus_setup_fb_gpios()) + pr_err("Failed to setup fb gpios\n"); + else + set_pxa_fb_info(&zeus_fb_info); + + pxa_set_mci_info(&zeus_mci_platform_data); + pxa_set_udc_info(&zeus_udc_info); + pxa_set_ac97_info(&zeus_ac97_info); + pxa_set_i2c_info(NULL); + i2c_register_board_info(0, ARRAY_AND_SIZE(zeus_i2c_devices)); +} + +static struct map_desc zeus_io_desc[] __initdata = { + { + .virtual = ZEUS_CPLD_VERSION, + .pfn = __phys_to_pfn(ZEUS_CPLD_VERSION_PHYS), + .length = 0x1000, + .type = MT_DEVICE, + }, + { + .virtual = ZEUS_CPLD_ISA_IRQ, + .pfn = __phys_to_pfn(ZEUS_CPLD_ISA_IRQ_PHYS), + .length = 0x1000, + .type = MT_DEVICE, + }, + { + .virtual = ZEUS_CPLD_CONTROL, + .pfn = __phys_to_pfn(ZEUS_CPLD_CONTROL_PHYS), + .length = 0x1000, + .type = MT_DEVICE, + }, + { + .virtual = ZEUS_CPLD_EXTWDOG, + .pfn = __phys_to_pfn(ZEUS_CPLD_EXTWDOG_PHYS), + .length = 0x1000, + .type = MT_DEVICE, + }, + { + .virtual = ZEUS_PC104IO, + .pfn = __phys_to_pfn(ZEUS_PC104IO_PHYS), + .length = 0x00800000, + .type = MT_DEVICE, + }, +}; + +static void __init zeus_map_io(void) +{ + pxa_map_io(); + + iotable_init(zeus_io_desc, ARRAY_SIZE(zeus_io_desc)); + + /* Clear PSPR to ensure a full restart on wake-up. */ + PMCR = PSPR = 0; + + /* enable internal 32.768Khz oscillator (ignore OSCC_OOK) */ + OSCC |= OSCC_OON; + + /* Some clock cycles later (from OSCC_ON), programme PCFR (OPDE...). + * float chip selects and PCMCIA */ + PCFR = PCFR_OPDE | PCFR_DC_EN | PCFR_FS | PCFR_FP; +} + +MACHINE_START(ARCOM_ZEUS, "Arcom ZEUS") + /* Maintainer: Marc Zyngier <maz@misterjones.org> */ + .phys_io = 0x40000000, + .io_pg_offst = ((io_p2v(0x40000000) >> 18) & 0xfffc), + .boot_params = 0xa0000100, + .map_io = zeus_map_io, + .init_irq = zeus_init_irq, + .timer = &pxa_timer, + .init_machine = zeus_init, +MACHINE_END + diff --git a/arch/arm/mach-realview/Kconfig b/arch/arm/mach-realview/Kconfig index c48e1f2c3349..ee5e392430e8 100644 --- a/arch/arm/mach-realview/Kconfig +++ b/arch/arm/mach-realview/Kconfig @@ -70,7 +70,7 @@ config MACH_REALVIEW_PBX bool "Support RealView/PBX platform" select ARM_GIC select HAVE_PATA_PLATFORM - select ARCH_SPARSEMEM_ENABLE if CPU_V7 && !HIGH_PHYS_OFFSET + select ARCH_SPARSEMEM_ENABLE if CPU_V7 && !REALVIEW_HIGH_PHYS_OFFSET select ZONE_DMA if SPARSEMEM help Include support for the ARM(R) RealView PBX platform. diff --git a/arch/arm/mach-s3c2442/mach-gta02.c b/arch/arm/mach-s3c2442/mach-gta02.c index f76d6ff4aeb9..0b4a3a03071f 100644 --- a/arch/arm/mach-s3c2442/mach-gta02.c +++ b/arch/arm/mach-s3c2442/mach-gta02.c @@ -268,6 +268,9 @@ struct pcf50633_platform_data gta02_pcf_pdata = { .batteries = gta02_batteries, .num_batteries = ARRAY_SIZE(gta02_batteries), + + .charger_reference_current_ma = 1000, + .reg_init_data = { [PCF50633_REGULATOR_AUTO] = { .constraints = { diff --git a/arch/arm/mach-s3c24a0/include/mach/memory.h b/arch/arm/mach-s3c24a0/include/mach/memory.h index 585211ca0187..7d74fd5c8d66 100644 --- a/arch/arm/mach-s3c24a0/include/mach/memory.h +++ b/arch/arm/mach-s3c24a0/include/mach/memory.h @@ -15,5 +15,7 @@ #define __virt_to_bus(x) __virt_to_phys(x) #define __bus_to_virt(x) __phys_to_virt(x) +#define __pfn_to_bus(x) __pfn_to_phys(x) +#define __bus_to_pfn(x) __phys_to_pfn(x) #endif diff --git a/arch/arm/mach-sa1100/Kconfig b/arch/arm/mach-sa1100/Kconfig index 03a7f3857c5e..b17d52f7cc48 100644 --- a/arch/arm/mach-sa1100/Kconfig +++ b/arch/arm/mach-sa1100/Kconfig @@ -4,6 +4,7 @@ menu "SA11x0 Implementations" config SA1100_ASSABET bool "Assabet" + select CPU_FREQ_SA1110 help Say Y here if you are using the Intel(R) StrongARM(R) SA-1110 Microprocessor Development Board (also known as the Assabet). @@ -19,6 +20,7 @@ config ASSABET_NEPONSET config SA1100_CERF bool "CerfBoard" + select CPU_FREQ_SA1110 help The Intrinsyc CerfBoard is based on the StrongARM 1110 (Discontinued). More information is available at: @@ -45,6 +47,7 @@ endchoice config SA1100_COLLIE bool "Sharp Zaurus SL5500" + # FIXME: select CPU_FREQ_SA11x0 select SHARP_LOCOMO select SHARP_SCOOP select SHARP_PARAM @@ -54,6 +57,7 @@ config SA1100_COLLIE config SA1100_H3100 bool "Compaq iPAQ H3100" select HTC_EGPIO + select CPU_FREQ_SA1100 help Say Y here if you intend to run this kernel on the Compaq iPAQ H3100 handheld computer. Information about this machine and the @@ -64,6 +68,7 @@ config SA1100_H3100 config SA1100_H3600 bool "Compaq iPAQ H3600/H3700" select HTC_EGPIO + select CPU_FREQ_SA1100 help Say Y here if you intend to run this kernel on the Compaq iPAQ H3600 handheld computer. Information about this machine and the @@ -74,6 +79,7 @@ config SA1100_H3600 config SA1100_BADGE4 bool "HP Labs BadgePAD 4" select SA1111 + select CPU_FREQ_SA1100 help Say Y here if you want to build a kernel for the HP Laboratories BadgePAD 4. @@ -81,6 +87,7 @@ config SA1100_BADGE4 config SA1100_JORNADA720 bool "HP Jornada 720" select SA1111 + # FIXME: select CPU_FREQ_SA11x0 help Say Y here if you want to build a kernel for the HP Jornada 720 handheld computer. See <http://www.hp.com/jornada/products/720> @@ -98,12 +105,14 @@ config SA1100_JORNADA720_SSP config SA1100_HACKKIT bool "HackKit Core CPU Board" + select CPU_FREQ_SA1100 help Say Y here to support the HackKit Core CPU Board <http://hackkit.eletztrick.de>; config SA1100_LART bool "LART" + select CPU_FREQ_SA1100 help Say Y here if you are using the Linux Advanced Radio Terminal (also known as the LART). See <http://www.lartmaker.nl/> for @@ -111,6 +120,7 @@ config SA1100_LART config SA1100_PLEB bool "PLEB" + select CPU_FREQ_SA1100 help Say Y here if you are using version 1 of the Portable Linux Embedded Board (also known as PLEB). @@ -119,6 +129,7 @@ config SA1100_PLEB config SA1100_SHANNON bool "Shannon" + select CPU_FREQ_SA1100 help The Shannon (also known as a Tuxscreen, and also as a IS2630) was a limited edition webphone produced by Philips. The Shannon is a SA1100 @@ -127,6 +138,7 @@ config SA1100_SHANNON config SA1100_SIMPAD bool "Simpad" + select CPU_FREQ_SA1110 help The SIEMENS webpad SIMpad is based on the StrongARM 1110. There are two different versions CL4 and SL4. CL4 has 32MB RAM and 16MB @@ -145,3 +157,4 @@ config SA1100_SSP endmenu endif + diff --git a/arch/arm/mach-sa1100/generic.c b/arch/arm/mach-sa1100/generic.c index 9faea1511c1f..3c1fcd696714 100644 --- a/arch/arm/mach-sa1100/generic.c +++ b/arch/arm/mach-sa1100/generic.c @@ -58,7 +58,6 @@ static const unsigned short cclk_frequency_100khz[NR_FREQS] = { 2802 /* 280.2 MHz */ }; -#if defined(CONFIG_CPU_FREQ_SA1100) || defined(CONFIG_CPU_FREQ_SA1110) /* rounds up(!) */ unsigned int sa11x0_freq_to_ppcr(unsigned int khz) { @@ -110,17 +109,6 @@ unsigned int sa11x0_getspeed(unsigned int cpu) return cclk_frequency_100khz[PPCR & 0xf] * 100; } -#else -/* - * We still need to provide this so building without cpufreq works. - */ -unsigned int cpufreq_get(unsigned int cpu) -{ - return cclk_frequency_100khz[PPCR & 0xf] * 100; -} -EXPORT_SYMBOL(cpufreq_get); -#endif - /* * This is the SA11x0 sched_clock implementation. This has * a resolution of 271ns, and a maximum value of 32025597s (370 days). diff --git a/arch/arm/mach-u300/include/mach/coh901318.h b/arch/arm/mach-u300/include/mach/coh901318.h new file mode 100644 index 000000000000..f4cfee9c7d28 --- /dev/null +++ b/arch/arm/mach-u300/include/mach/coh901318.h @@ -0,0 +1,281 @@ +/* + * + * include/linux/coh901318.h + * + * + * Copyright (C) 2007-2009 ST-Ericsson + * License terms: GNU General Public License (GPL) version 2 + * DMA driver for COH 901 318 + * Author: Per Friden <per.friden@stericsson.com> + */ + +#ifndef COH901318_H +#define COH901318_H + +#include <linux/device.h> +#include <linux/dmaengine.h> + +#define MAX_DMA_PACKET_SIZE_SHIFT 11 +#define MAX_DMA_PACKET_SIZE (1 << MAX_DMA_PACKET_SIZE_SHIFT) + +/** + * struct coh901318_lli - linked list item for DMAC + * @control: control settings for DMAC + * @src_addr: transfer source address + * @dst_addr: transfer destination address + * @link_addr: physical address to next lli + * @virt_link_addr: virtual addres of next lli (only used by pool_free) + * @phy_this: physical address of current lli (only used by pool_free) + */ +struct coh901318_lli { + u32 control; + dma_addr_t src_addr; + dma_addr_t dst_addr; + dma_addr_t link_addr; + + void *virt_link_addr; + dma_addr_t phy_this; +}; +/** + * struct coh901318_params - parameters for DMAC configuration + * @config: DMA config register + * @ctrl_lli_last: DMA control register for the last lli in the list + * @ctrl_lli: DMA control register for an lli + * @ctrl_lli_chained: DMA control register for a chained lli + */ +struct coh901318_params { + u32 config; + u32 ctrl_lli_last; + u32 ctrl_lli; + u32 ctrl_lli_chained; +}; +/** + * struct coh_dma_channel - dma channel base + * @name: ascii name of dma channel + * @number: channel id number + * @desc_nbr_max: number of preallocated descriptortors + * @priority_high: prio of channel, 0 low otherwise high. + * @param: configuration parameters + * @dev_addr: physical address of periphal connected to channel + */ +struct coh_dma_channel { + const char name[32]; + const int number; + const int desc_nbr_max; + const int priority_high; + const struct coh901318_params param; + const dma_addr_t dev_addr; +}; + +/** + * dma_access_memory_state_t - register dma for memory access + * + * @dev: The dma device + * @active: 1 means dma intends to access memory + * 0 means dma wont access memory + */ +typedef void (*dma_access_memory_state_t)(struct device *dev, + bool active); + +/** + * struct powersave - DMA power save structure + * @lock: lock protecting data in this struct + * @started_channels: bit mask indicating active dma channels + */ +struct powersave { + spinlock_t lock; + u64 started_channels; +}; +/** + * struct coh901318_platform - platform arch structure + * @chans_slave: specifying dma slave channels + * @chans_memcpy: specifying dma memcpy channels + * @access_memory_state: requesting DMA memeory access (on / off) + * @chan_conf: dma channel configurations + * @max_channels: max number of dma chanenls + */ +struct coh901318_platform { + const int *chans_slave; + const int *chans_memcpy; + const dma_access_memory_state_t access_memory_state; + const struct coh_dma_channel *chan_conf; + const int max_channels; +}; + +/** + * coh901318_get_bytes_left() - Get number of bytes left on a current transfer + * @chan: dma channel handle + * return number of bytes left, or negative on error + */ +u32 coh901318_get_bytes_left(struct dma_chan *chan); + +/** + * coh901318_stop() - Stops dma transfer + * @chan: dma channel handle + * return 0 on success otherwise negative value + */ +void coh901318_stop(struct dma_chan *chan); + +/** + * coh901318_continue() - Resumes a stopped dma transfer + * @chan: dma channel handle + * return 0 on success otherwise negative value + */ +void coh901318_continue(struct dma_chan *chan); + +/** + * coh901318_filter_id() - DMA channel filter function + * @chan: dma channel handle + * @chan_id: id of dma channel to be filter out + * + * In dma_request_channel() it specifies what channel id to be requested + */ +bool coh901318_filter_id(struct dma_chan *chan, void *chan_id); + +/* + * DMA Controller - this access the static mappings of the coh901318 dma. + * + */ + +#define COH901318_MOD32_MASK (0x1F) +#define COH901318_WORD_MASK (0xFFFFFFFF) +/* INT_STATUS - Interrupt Status Registers 32bit (R/-) */ +#define COH901318_INT_STATUS1 (0x0000) +#define COH901318_INT_STATUS2 (0x0004) +/* TC_INT_STATUS - Terminal Count Interrupt Status Registers 32bit (R/-) */ +#define COH901318_TC_INT_STATUS1 (0x0008) +#define COH901318_TC_INT_STATUS2 (0x000C) +/* TC_INT_CLEAR - Terminal Count Interrupt Clear Registers 32bit (-/W) */ +#define COH901318_TC_INT_CLEAR1 (0x0010) +#define COH901318_TC_INT_CLEAR2 (0x0014) +/* RAW_TC_INT_STATUS - Raw Term Count Interrupt Status Registers 32bit (R/-) */ +#define COH901318_RAW_TC_INT_STATUS1 (0x0018) +#define COH901318_RAW_TC_INT_STATUS2 (0x001C) +/* BE_INT_STATUS - Bus Error Interrupt Status Registers 32bit (R/-) */ +#define COH901318_BE_INT_STATUS1 (0x0020) +#define COH901318_BE_INT_STATUS2 (0x0024) +/* BE_INT_CLEAR - Bus Error Interrupt Clear Registers 32bit (-/W) */ +#define COH901318_BE_INT_CLEAR1 (0x0028) +#define COH901318_BE_INT_CLEAR2 (0x002C) +/* RAW_BE_INT_STATUS - Raw Term Count Interrupt Status Registers 32bit (R/-) */ +#define COH901318_RAW_BE_INT_STATUS1 (0x0030) +#define COH901318_RAW_BE_INT_STATUS2 (0x0034) + +/* + * CX_CFG - Channel Configuration Registers 32bit (R/W) + */ +#define COH901318_CX_CFG (0x0100) +#define COH901318_CX_CFG_SPACING (0x04) +/* Channel enable activates tha dma job */ +#define COH901318_CX_CFG_CH_ENABLE (0x00000001) +#define COH901318_CX_CFG_CH_DISABLE (0x00000000) +/* Request Mode */ +#define COH901318_CX_CFG_RM_MASK (0x00000006) +#define COH901318_CX_CFG_RM_MEMORY_TO_MEMORY (0x0 << 1) +#define COH901318_CX_CFG_RM_PRIMARY_TO_MEMORY (0x1 << 1) +#define COH901318_CX_CFG_RM_MEMORY_TO_PRIMARY (0x1 << 1) +#define COH901318_CX_CFG_RM_PRIMARY_TO_SECONDARY (0x3 << 1) +#define COH901318_CX_CFG_RM_SECONDARY_TO_PRIMARY (0x3 << 1) +/* Linked channel request field. RM must == 11 */ +#define COH901318_CX_CFG_LCRF_SHIFT 3 +#define COH901318_CX_CFG_LCRF_MASK (0x000001F8) +#define COH901318_CX_CFG_LCR_DISABLE (0x00000000) +/* Terminal Counter Interrupt Request Mask */ +#define COH901318_CX_CFG_TC_IRQ_ENABLE (0x00000200) +#define COH901318_CX_CFG_TC_IRQ_DISABLE (0x00000000) +/* Bus Error interrupt Mask */ +#define COH901318_CX_CFG_BE_IRQ_ENABLE (0x00000400) +#define COH901318_CX_CFG_BE_IRQ_DISABLE (0x00000000) + +/* + * CX_STAT - Channel Status Registers 32bit (R/-) + */ +#define COH901318_CX_STAT (0x0200) +#define COH901318_CX_STAT_SPACING (0x04) +#define COH901318_CX_STAT_RBE_IRQ_IND (0x00000008) +#define COH901318_CX_STAT_RTC_IRQ_IND (0x00000004) +#define COH901318_CX_STAT_ACTIVE (0x00000002) +#define COH901318_CX_STAT_ENABLED (0x00000001) + +/* + * CX_CTRL - Channel Control Registers 32bit (R/W) + */ +#define COH901318_CX_CTRL (0x0400) +#define COH901318_CX_CTRL_SPACING (0x10) +/* Transfer Count Enable */ +#define COH901318_CX_CTRL_TC_ENABLE (0x00001000) +#define COH901318_CX_CTRL_TC_DISABLE (0x00000000) +/* Transfer Count Value 0 - 4095 */ +#define COH901318_CX_CTRL_TC_VALUE_MASK (0x00000FFF) +/* Burst count */ +#define COH901318_CX_CTRL_BURST_COUNT_MASK (0x0000E000) +#define COH901318_CX_CTRL_BURST_COUNT_64_BYTES (0x7 << 13) +#define COH901318_CX_CTRL_BURST_COUNT_48_BYTES (0x6 << 13) +#define COH901318_CX_CTRL_BURST_COUNT_32_BYTES (0x5 << 13) +#define COH901318_CX_CTRL_BURST_COUNT_16_BYTES (0x4 << 13) +#define COH901318_CX_CTRL_BURST_COUNT_8_BYTES (0x3 << 13) +#define COH901318_CX_CTRL_BURST_COUNT_4_BYTES (0x2 << 13) +#define COH901318_CX_CTRL_BURST_COUNT_2_BYTES (0x1 << 13) +#define COH901318_CX_CTRL_BURST_COUNT_1_BYTE (0x0 << 13) +/* Source bus size */ +#define COH901318_CX_CTRL_SRC_BUS_SIZE_MASK (0x00030000) +#define COH901318_CX_CTRL_SRC_BUS_SIZE_32_BITS (0x2 << 16) +#define COH901318_CX_CTRL_SRC_BUS_SIZE_16_BITS (0x1 << 16) +#define COH901318_CX_CTRL_SRC_BUS_SIZE_8_BITS (0x0 << 16) +/* Source address increment */ +#define COH901318_CX_CTRL_SRC_ADDR_INC_ENABLE (0x00040000) +#define COH901318_CX_CTRL_SRC_ADDR_INC_DISABLE (0x00000000) +/* Destination Bus Size */ +#define COH901318_CX_CTRL_DST_BUS_SIZE_MASK (0x00180000) +#define COH901318_CX_CTRL_DST_BUS_SIZE_32_BITS (0x2 << 19) +#define COH901318_CX_CTRL_DST_BUS_SIZE_16_BITS (0x1 << 19) +#define COH901318_CX_CTRL_DST_BUS_SIZE_8_BITS (0x0 << 19) +/* Destination address increment */ +#define COH901318_CX_CTRL_DST_ADDR_INC_ENABLE (0x00200000) +#define COH901318_CX_CTRL_DST_ADDR_INC_DISABLE (0x00000000) +/* Master Mode (Master2 is only connected to MSL) */ +#define COH901318_CX_CTRL_MASTER_MODE_MASK (0x00C00000) +#define COH901318_CX_CTRL_MASTER_MODE_M2R_M1W (0x3 << 22) +#define COH901318_CX_CTRL_MASTER_MODE_M1R_M2W (0x2 << 22) +#define COH901318_CX_CTRL_MASTER_MODE_M2RW (0x1 << 22) +#define COH901318_CX_CTRL_MASTER_MODE_M1RW (0x0 << 22) +/* Terminal Count flag to PER enable */ +#define COH901318_CX_CTRL_TCP_ENABLE (0x01000000) +#define COH901318_CX_CTRL_TCP_DISABLE (0x00000000) +/* Terminal Count flags to CPU enable */ +#define COH901318_CX_CTRL_TC_IRQ_ENABLE (0x02000000) +#define COH901318_CX_CTRL_TC_IRQ_DISABLE (0x00000000) +/* Hand shake to peripheral */ +#define COH901318_CX_CTRL_HSP_ENABLE (0x04000000) +#define COH901318_CX_CTRL_HSP_DISABLE (0x00000000) +#define COH901318_CX_CTRL_HSS_ENABLE (0x08000000) +#define COH901318_CX_CTRL_HSS_DISABLE (0x00000000) +/* DMA mode */ +#define COH901318_CX_CTRL_DDMA_MASK (0x30000000) +#define COH901318_CX_CTRL_DDMA_LEGACY (0x0 << 28) +#define COH901318_CX_CTRL_DDMA_DEMAND_DMA1 (0x1 << 28) +#define COH901318_CX_CTRL_DDMA_DEMAND_DMA2 (0x2 << 28) +/* Primary Request Data Destination */ +#define COH901318_CX_CTRL_PRDD_MASK (0x40000000) +#define COH901318_CX_CTRL_PRDD_DEST (0x1 << 30) +#define COH901318_CX_CTRL_PRDD_SOURCE (0x0 << 30) + +/* + * CX_SRC_ADDR - Channel Source Address Registers 32bit (R/W) + */ +#define COH901318_CX_SRC_ADDR (0x0404) +#define COH901318_CX_SRC_ADDR_SPACING (0x10) + +/* + * CX_DST_ADDR - Channel Destination Address Registers 32bit R/W + */ +#define COH901318_CX_DST_ADDR (0x0408) +#define COH901318_CX_DST_ADDR_SPACING (0x10) + +/* + * CX_LNK_ADDR - Channel Link Address Registers 32bit (R/W) + */ +#define COH901318_CX_LNK_ADDR (0x040C) +#define COH901318_CX_LNK_ADDR_SPACING (0x10) +#define COH901318_CX_LNK_LINK_IMMEDIATE (0x00000001) +#endif /* COH901318_H */ diff --git a/arch/arm/mach-w90x900/include/mach/nuc900_spi.h b/arch/arm/mach-w90x900/include/mach/nuc900_spi.h new file mode 100644 index 000000000000..bd94819e314f --- /dev/null +++ b/arch/arm/mach-w90x900/include/mach/nuc900_spi.h @@ -0,0 +1,35 @@ +/* + * arch/arm/mach-w90x900/include/mach/nuc900_spi.h + * + * Copyright (c) 2009 Nuvoton technology corporation. + * + * Wan ZongShun <mcuos.com@gmail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation;version 2 of the License. + * + */ + +#ifndef __ASM_ARCH_SPI_H +#define __ASM_ARCH_SPI_H + +extern void mfp_set_groupg(struct device *dev); + +struct nuc900_spi_info { + unsigned int num_cs; + unsigned int lsb; + unsigned int txneg; + unsigned int rxneg; + unsigned int divider; + unsigned int sleep; + unsigned int txnum; + unsigned int txbitlen; + int bus_num; +}; + +struct nuc900_spi_chip { + unsigned char bits_per_word; +}; + +#endif /* __ASM_ARCH_SPI_H */ diff --git a/arch/arm/plat-mxc/include/mach/mxc_nand.h b/arch/arm/plat-mxc/include/mach/mxc_nand.h index 2b972df22d12..5d2d21d414e0 100644 --- a/arch/arm/plat-mxc/include/mach/mxc_nand.h +++ b/arch/arm/plat-mxc/include/mach/mxc_nand.h @@ -22,6 +22,7 @@ struct mxc_nand_platform_data { int width; /* data bus width in bytes */ - int hw_ecc; /* 0 if supress hardware ECC */ + int hw_ecc:1; /* 0 if supress hardware ECC */ + int flash_bbt:1; /* set to 1 to use a flash based bbt */ }; #endif /* __ASM_ARCH_NAND_H */ diff --git a/arch/arm/plat-omap/debug-leds.c b/arch/arm/plat-omap/debug-leds.c index 6c768b71ad64..53fcef7c5201 100644 --- a/arch/arm/plat-omap/debug-leds.c +++ b/arch/arm/plat-omap/debug-leds.c @@ -293,7 +293,7 @@ static int fpga_resume_noirq(struct device *dev) return 0; } -static struct dev_pm_ops fpga_dev_pm_ops = { +static const struct dev_pm_ops fpga_dev_pm_ops = { .suspend_noirq = fpga_suspend_noirq, .resume_noirq = fpga_resume_noirq, }; diff --git a/arch/arm/plat-omap/gpio.c b/arch/arm/plat-omap/gpio.c index 055160e0620e..04846811d0aa 100644 --- a/arch/arm/plat-omap/gpio.c +++ b/arch/arm/plat-omap/gpio.c @@ -1431,7 +1431,7 @@ static int omap_mpuio_resume_noirq(struct device *dev) return 0; } -static struct dev_pm_ops omap_mpuio_dev_pm_ops = { +static const struct dev_pm_ops omap_mpuio_dev_pm_ops = { .suspend_noirq = omap_mpuio_suspend_noirq, .resume_noirq = omap_mpuio_resume_noirq, }; diff --git a/arch/arm/plat-omap/include/plat/irqs.h b/arch/arm/plat-omap/include/plat/irqs.h index ce5dd2d1dc21..97d6c50c3dcb 100644 --- a/arch/arm/plat-omap/include/plat/irqs.h +++ b/arch/arm/plat-omap/include/plat/irqs.h @@ -472,8 +472,22 @@ #endif #define TWL4030_GPIO_IRQ_END (TWL4030_GPIO_IRQ_BASE + TWL4030_GPIO_NR_IRQS) +#define TWL6030_IRQ_BASE (OMAP_FPGA_IRQ_END) +#ifdef CONFIG_TWL4030_CORE +#define TWL6030_BASE_NR_IRQS 20 +#else +#define TWL6030_BASE_NR_IRQS 0 +#endif +#define TWL6030_IRQ_END (TWL6030_IRQ_BASE + TWL6030_BASE_NR_IRQS) + /* Total number of interrupts depends on the enabled blocks above */ -#define NR_IRQS TWL4030_GPIO_IRQ_END +#if (TWL4030_GPIO_IRQ_END > TWL6030_IRQ_END) +#define TWL_IRQ_END TWL4030_GPIO_IRQ_END +#else +#define TWL_IRQ_END TWL6030_IRQ_END +#endif + +#define NR_IRQS TWL_IRQ_END #define OMAP_IRQ_BIT(irq) (1 << ((irq) % 32)) diff --git a/arch/arm/plat-s3c/include/plat/nand.h b/arch/arm/plat-s3c/include/plat/nand.h index 065985978413..226147b7e026 100644 --- a/arch/arm/plat-s3c/include/plat/nand.h +++ b/arch/arm/plat-s3c/include/plat/nand.h @@ -17,6 +17,7 @@ * Setting this flag will allow the kernel to * look for it at boot time and also skip the NAND * scan. + * @options: Default value to set into 'struct nand_chip' options. * @nr_chips: Number of chips in this set * @nr_partitions: Number of partitions pointed to by @partitions * @name: Name of set (optional) @@ -31,6 +32,7 @@ struct s3c2410_nand_set { unsigned int disable_ecc:1; unsigned int flash_bbt:1; + unsigned int options; int nr_chips; int nr_partitions; char *name; diff --git a/arch/arm/vfp/vfpmodule.c b/arch/arm/vfp/vfpmodule.c index 2d7423af1197..aed05bc3c2ea 100644 --- a/arch/arm/vfp/vfpmodule.c +++ b/arch/arm/vfp/vfpmodule.c @@ -38,16 +38,72 @@ union vfp_state *last_VFP_context[NR_CPUS]; */ unsigned int VFP_arch; +/* + * Per-thread VFP initialization. + */ +static void vfp_thread_flush(struct thread_info *thread) +{ + union vfp_state *vfp = &thread->vfpstate; + unsigned int cpu; + + memset(vfp, 0, sizeof(union vfp_state)); + + vfp->hard.fpexc = FPEXC_EN; + vfp->hard.fpscr = FPSCR_ROUND_NEAREST; + + /* + * Disable VFP to ensure we initialize it first. We must ensure + * that the modification of last_VFP_context[] and hardware disable + * are done for the same CPU and without preemption. + */ + cpu = get_cpu(); + if (last_VFP_context[cpu] == vfp) + last_VFP_context[cpu] = NULL; + fmxr(FPEXC, fmrx(FPEXC) & ~FPEXC_EN); + put_cpu(); +} + +static void vfp_thread_release(struct thread_info *thread) +{ + /* release case: Per-thread VFP cleanup. */ + union vfp_state *vfp = &thread->vfpstate; + unsigned int cpu = thread->cpu; + + if (last_VFP_context[cpu] == vfp) + last_VFP_context[cpu] = NULL; +} + +/* + * When this function is called with the following 'cmd's, the following + * is true while this function is being run: + * THREAD_NOFTIFY_SWTICH: + * - the previously running thread will not be scheduled onto another CPU. + * - the next thread to be run (v) will not be running on another CPU. + * - thread->cpu is the local CPU number + * - not preemptible as we're called in the middle of a thread switch + * THREAD_NOTIFY_FLUSH: + * - the thread (v) will be running on the local CPU, so + * v === current_thread_info() + * - thread->cpu is the local CPU number at the time it is accessed, + * but may change at any time. + * - we could be preempted if tree preempt rcu is enabled, so + * it is unsafe to use thread->cpu. + * THREAD_NOTIFY_RELEASE: + * - the thread (v) will not be running on any CPU; it is a dead thread. + * - thread->cpu will be the last CPU the thread ran on, which may not + * be the current CPU. + * - we could be preempted if tree preempt rcu is enabled. + */ static int vfp_notifier(struct notifier_block *self, unsigned long cmd, void *v) { struct thread_info *thread = v; - union vfp_state *vfp; - __u32 cpu = thread->cpu; if (likely(cmd == THREAD_NOTIFY_SWITCH)) { u32 fpexc = fmrx(FPEXC); #ifdef CONFIG_SMP + unsigned int cpu = thread->cpu; + /* * On SMP, if VFP is enabled, save the old state in * case the thread migrates to a different CPU. The @@ -74,25 +130,10 @@ static int vfp_notifier(struct notifier_block *self, unsigned long cmd, void *v) return NOTIFY_DONE; } - vfp = &thread->vfpstate; - if (cmd == THREAD_NOTIFY_FLUSH) { - /* - * Per-thread VFP initialisation. - */ - memset(vfp, 0, sizeof(union vfp_state)); - - vfp->hard.fpexc = FPEXC_EN; - vfp->hard.fpscr = FPSCR_ROUND_NEAREST; - - /* - * Disable VFP to ensure we initialise it first. - */ - fmxr(FPEXC, fmrx(FPEXC) & ~FPEXC_EN); - } - - /* flush and release case: Per-thread VFP cleanup. */ - if (last_VFP_context[cpu] == vfp) - last_VFP_context[cpu] = NULL; + if (cmd == THREAD_NOTIFY_FLUSH) + vfp_thread_flush(thread); + else + vfp_thread_release(thread); return NOTIFY_DONE; } |