diff options
Diffstat (limited to 'arch/mips/au1000/pb1100/board_setup.c')
| -rw-r--r-- | arch/mips/au1000/pb1100/board_setup.c | 50 |
1 files changed, 26 insertions, 24 deletions
diff --git a/arch/mips/au1000/pb1100/board_setup.c b/arch/mips/au1000/pb1100/board_setup.c index 656164c8e9ca..c0bfd59a7a36 100644 --- a/arch/mips/au1000/pb1100/board_setup.c +++ b/arch/mips/au1000/pb1100/board_setup.c @@ -1,7 +1,6 @@ /* - * Copyright 2002 MontaVista Software Inc. - * Author: MontaVista Software, Inc. - * ppopov@mvista.com or source@mvista.com + * Copyright 2002, 2008 MontaVista Software Inc. + * Author: MontaVista Software, Inc. <source@mvista.com> * * This program is free software; you can redistribute it and/or modify it * under the terms of the GNU General Public License as published by the @@ -32,15 +31,15 @@ void board_reset(void) { - /* Hit BCSR.SYSTEM_CONTROL[SW_RST] */ - au_writel(0x00000000, 0xAE00001C); + /* Hit BCSR.RST_VDDI[SOFT_RESET] */ + au_writel(0x00000000, PB1100_RST_VDDI); } void __init board_setup(void) { - volatile void __iomem * base = (volatile void __iomem *) 0xac000000UL; + volatile void __iomem *base = (volatile void __iomem *)0xac000000UL; - // set AUX clock to 12MHz * 8 = 96 MHz + /* Set AUX clock to 12 MHz * 8 = 96 MHz */ au_writel(8, SYS_AUXPLL); au_writel(0, SYS_PININPUTEN); udelay(100); @@ -49,44 +48,47 @@ void __init board_setup(void) { u32 pin_func, sys_freqctrl, sys_clksrc; - // configure pins GPIO[14:9] as GPIO - pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x80); + /* Configure pins GPIO[14:9] as GPIO */ + pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_UR3; - /* zero and disable FREQ2 */ + /* Zero and disable FREQ2 */ sys_freqctrl = au_readl(SYS_FREQCTRL0); sys_freqctrl &= ~0xFFF00000; au_writel(sys_freqctrl, SYS_FREQCTRL0); - /* zero and disable USBH/USBD/IrDA clock */ + /* Zero and disable USBH/USBD/IrDA clock */ sys_clksrc = au_readl(SYS_CLKSRC); - sys_clksrc &= ~0x0000001F; + sys_clksrc &= ~(SYS_CS_CIR | SYS_CS_DIR | SYS_CS_MIR_MASK); au_writel(sys_clksrc, SYS_CLKSRC); sys_freqctrl = au_readl(SYS_FREQCTRL0); sys_freqctrl &= ~0xFFF00000; sys_clksrc = au_readl(SYS_CLKSRC); - sys_clksrc &= ~0x0000001F; + sys_clksrc &= ~(SYS_CS_CIR | SYS_CS_DIR | SYS_CS_MIR_MASK); - // FREQ2 = aux/2 = 48 MHz - sys_freqctrl |= ((0<<22) | (1<<21) | (1<<20)); + /* FREQ2 = aux / 2 = 48 MHz */ + sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) | + SYS_FC_FE2 | SYS_FC_FS2; au_writel(sys_freqctrl, SYS_FREQCTRL0); /* - * Route 48MHz FREQ2 into USBH/USBD/IrDA + * Route 48 MHz FREQ2 into USBH/USBD/IrDA */ - sys_clksrc |= ((4<<2) | (0<<1) | 0 ); + sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MIR_BIT; au_writel(sys_clksrc, SYS_CLKSRC); - /* setup the static bus controller */ + /* Setup the static bus controller */ au_writel(0x00000002, MEM_STCFG3); /* type = PCMCIA */ au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */ au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */ - // get USB Functionality pin state (device vs host drive pins) - pin_func = au_readl(SYS_PINFUNC) & (u32)(~0x8000); - // 2nd USB port is USB host - pin_func |= 0x8000; + /* + * Get USB Functionality pin state (device vs host drive pins). + */ + pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_USB; + /* 2nd USB port is USB host. */ + pin_func |= SYS_PF_USB; au_writel(pin_func, SYS_PINFUNC); } #endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */ @@ -94,12 +96,12 @@ void __init board_setup(void) /* Enable sys bus clock divider when IDLE state or no bus activity. */ au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL); - // Enable the RTC if not already enabled + /* Enable the RTC if not already enabled. */ if (!(readb(base + 0x28) & 0x20)) { writeb(readb(base + 0x28) | 0x20, base + 0x28); au_sync(); } - // Put the clock in BCD mode + /* Put the clock in BCD mode. */ if (readb(base + 0x2C) & 0x4) { /* reg B */ writeb(readb(base + 0x2c) & ~0x4, base + 0x2c); au_sync(); |