diff options
Diffstat (limited to 'arch')
| -rw-r--r-- | arch/cris/Kconfig | 46 | ||||
| -rw-r--r-- | arch/cris/arch-v10/drivers/Kconfig | 23 | ||||
| -rw-r--r-- | arch/cris/arch-v32/drivers/Kconfig | 394 | ||||
| -rw-r--r-- | arch/cris/arch-v32/mach-a3/Kconfig | 4 |
4 files changed, 0 insertions, 467 deletions
diff --git a/arch/cris/Kconfig b/arch/cris/Kconfig index d4b6626ec323..c699d3259872 100644 --- a/arch/cris/Kconfig +++ b/arch/cris/Kconfig @@ -172,12 +172,6 @@ config ETRAX_FLASH_BUSWIDTH help Width in bytes of the NOR Flash bus (1, 2 or 4). Is usually 2. -config ETRAX_NANDFLASH_BUSWIDTH - int "Buswidth of NAND flash in bytes" - default "1" - help - Width in bytes of the NAND flash (1 or 2). - config ETRAX_FLASH1_SIZE int "FLASH1 size (dec, in MB. 0 = Unknown)" default "0" @@ -543,26 +537,6 @@ config ETRAX_SERIAL_PORT3_DMA5_IN depends on ETRAX_ARCH_V10 bool "DMA 5" -config ETRAX_SERIAL_PORT3_DMA9_IN - bool "Ser3 uses DMA9 for input" - depends on ETRAXFS - help - Enables the DMA9 input channel for ser3 (ttyS3). - If you do not enable DMA, an interrupt for each character will be - used when receiving data. - Normally you want to use DMA, unless you use the DMA channel for - something else. - -config ETRAX_SERIAL_PORT3_DMA3_IN - bool "Ser3 uses DMA3 for input" - depends on CRIS_MACH_ARTPEC3 - help - Enables the DMA3 input channel for ser3 (ttyS3). - If you do not enable DMA, an interrupt for each character will be - used when receiving data. - Normally you want to use DMA, unless you use the DMA channel for - something else. - endchoice choice @@ -580,26 +554,6 @@ config ETRAX_SERIAL_PORT3_DMA4_OUT depends on ETRAX_ARCH_V10 bool "DMA 4" -config ETRAX_SERIAL_PORT3_DMA8_OUT - bool "Ser3 uses DMA8 for output" - depends on ETRAXFS - help - Enables the DMA8 output channel for ser3 (ttyS3). - If you do not enable DMA, an interrupt for each character will be - used when transmitting data. - Normally you want to use DMA, unless you use the DMA channel for - something else. - -config ETRAX_SERIAL_PORT3_DMA2_OUT - bool "Ser3 uses DMA2 for output" - depends on CRIS_MACH_ARTPEC3 - help - Enables the DMA2 output channel for ser3 (ttyS3). - If you do not enable DMA, an interrupt for each character will be - used when transmitting data. - Normally you want to use DMA, unless you use the DMA channel for - something else. - endchoice endmenu diff --git a/arch/cris/arch-v10/drivers/Kconfig b/arch/cris/arch-v10/drivers/Kconfig index f7c4272fabf0..239dab0b95c1 100644 --- a/arch/cris/arch-v10/drivers/Kconfig +++ b/arch/cris/arch-v10/drivers/Kconfig @@ -417,16 +417,6 @@ config ETRAX_USB_HOST for CTRL and BULK traffic only, INTR traffic may work as well however (depending on the requirements of timeliness). -config ETRAX_USB_HOST_PORT1 - bool "USB port 1 enabled" - depends on ETRAX_USB_HOST - default n - -config ETRAX_USB_HOST_PORT2 - bool "USB port 2 enabled" - depends on ETRAX_USB_HOST - default n - config ETRAX_PTABLE_SECTOR int "Byte-offset of partition table sector" depends on ETRAX_AXISFLASHMAP @@ -527,19 +517,6 @@ config ETRAX_GPIO Remember that you need to setup the port directions appropriately in the General configuration. -config ETRAX_PA_BUTTON_BITMASK - hex "PA-buttons bitmask" - depends on ETRAX_GPIO - default "02" - help - This is a bitmask with information about what bits on PA that - are used for buttons. - Most products has a so called TEST button on PA1, if that's true - use 02 here. - Use 00 if there are no buttons on PA. - If the bitmask is <> 00 a button driver will be included in the gpio - driver. ETRAX general I/O support must be enabled. - config ETRAX_PA_CHANGEABLE_DIR hex "PA user changeable dir mask" depends on ETRAX_GPIO diff --git a/arch/cris/arch-v32/drivers/Kconfig b/arch/cris/arch-v32/drivers/Kconfig index 1d866d3ee2f8..6792503aaf79 100644 --- a/arch/cris/arch-v32/drivers/Kconfig +++ b/arch/cris/arch-v32/drivers/Kconfig @@ -19,64 +19,6 @@ config ETRAX_NO_PHY switch. This option should normally be disabled. If enabled, speed and duplex will be locked to 100 Mbit and full duplex. -config ETRAX_ETHERNET_IFACE0 - depends on ETRAX_ETHERNET - bool "Enable network interface 0" - -config ETRAX_ETHERNET_IFACE1 - depends on (ETRAX_ETHERNET && ETRAXFS) - bool "Enable network interface 1 (uses DMA6 and DMA7)" - -config ETRAX_ETHERNET_GBIT - depends on (ETRAX_ETHERNET && CRIS_MACH_ARTPEC3) - bool "Enable gigabit Ethernet support" - -choice - prompt "Eth0 led group" - depends on ETRAX_ETHERNET_IFACE0 - default ETRAX_ETH0_USE_LEDGRP0 - -config ETRAX_ETH0_USE_LEDGRP0 - bool "Use LED grp 0" - depends on ETRAX_NBR_LED_GRP_ONE || ETRAX_NBR_LED_GRP_TWO - help - Use LED grp 0 for eth0 - -config ETRAX_ETH0_USE_LEDGRP1 - bool "Use LED grp 1" - depends on ETRAX_NBR_LED_GRP_TWO - help - Use LED grp 1 for eth0 - -config ETRAX_ETH0_USE_LEDGRPNULL - bool "Use no LEDs for eth0" - help - Use no LEDs for eth0 -endchoice - -choice - prompt "Eth1 led group" - depends on ETRAX_ETHERNET_IFACE1 - default ETRAX_ETH1_USE_LEDGRP1 - -config ETRAX_ETH1_USE_LEDGRP0 - bool "Use LED grp 0" - depends on ETRAX_NBR_LED_GRP_ONE || ETRAX_NBR_LED_GRP_TWO - help - Use LED grp 0 for eth1 - -config ETRAX_ETH1_USE_LEDGRP1 - bool "Use LED grp 1" - depends on ETRAX_NBR_LED_GRP_TWO - help - Use LED grp 1 for eth1 - -config ETRAX_ETH1_USE_LEDGRPNULL - bool "Use no LEDs for eth1" - help - Use no LEDs for eth1 -endchoice - config ETRAXFS_SERIAL bool "Serial-port support" depends on ETRAX_ARCH_V32 @@ -108,261 +50,24 @@ config ETRAX_SERIAL_PORT0 if you do not need DMA to something else. ser0 can use dma4 or dma6 for output and dma5 or dma7 for input. -choice - prompt "Ser0 default port type " - depends on ETRAX_SERIAL_PORT0 - default ETRAX_SERIAL_PORT0_TYPE_232 - help - Type of serial port. - -config ETRAX_SERIAL_PORT0_TYPE_232 - bool "Ser0 is a RS-232 port" - help - Configure serial port 0 to be a RS-232 port. - -config ETRAX_SERIAL_PORT0_TYPE_485HD - bool "Ser0 is a half duplex RS-485 port" - depends on ETRAX_RS485 - help - Configure serial port 0 to be a half duplex (two wires) RS-485 port. - -config ETRAX_SERIAL_PORT0_TYPE_485FD - bool "Ser0 is a full duplex RS-485 port" - depends on ETRAX_RS485 - help - Configure serial port 0 to be a full duplex (four wires) RS-485 port. -endchoice - -config ETRAX_SER0_DTR_BIT - string "Ser 0 DTR bit (empty = not used)" - depends on ETRAX_SERIAL_PORT0 - -config ETRAX_SER0_RI_BIT - string "Ser 0 RI bit (empty = not used)" - depends on ETRAX_SERIAL_PORT0 - -config ETRAX_SER0_DSR_BIT - string "Ser 0 DSR bit (empty = not used)" - depends on ETRAX_SERIAL_PORT0 - -config ETRAX_SER0_CD_BIT - string "Ser 0 CD bit (empty = not used)" - depends on ETRAX_SERIAL_PORT0 - config ETRAX_SERIAL_PORT1 bool "Serial port 1 enabled" depends on ETRAXFS_SERIAL help Enables the ETRAX FS serial driver for ser1 (ttyS1). -choice - prompt "Ser1 default port type" - depends on ETRAX_SERIAL_PORT1 - default ETRAX_SERIAL_PORT1_TYPE_232 - help - Type of serial port. - -config ETRAX_SERIAL_PORT1_TYPE_232 - bool "Ser1 is a RS-232 port" - help - Configure serial port 1 to be a RS-232 port. - -config ETRAX_SERIAL_PORT1_TYPE_485HD - bool "Ser1 is a half duplex RS-485 port" - depends on ETRAX_RS485 - help - Configure serial port 1 to be a half duplex (two wires) RS-485 port. - -config ETRAX_SERIAL_PORT1_TYPE_485FD - bool "Ser1 is a full duplex RS-485 port" - depends on ETRAX_RS485 - help - Configure serial port 1 to be a full duplex (four wires) RS-485 port. -endchoice - -config ETRAX_SER1_DTR_BIT - string "Ser 1 DTR bit (empty = not used)" - depends on ETRAX_SERIAL_PORT1 - -config ETRAX_SER1_RI_BIT - string "Ser 1 RI bit (empty = not used)" - depends on ETRAX_SERIAL_PORT1 - -config ETRAX_SER1_DSR_BIT - string "Ser 1 DSR bit (empty = not used)" - depends on ETRAX_SERIAL_PORT1 - -config ETRAX_SER1_CD_BIT - string "Ser 1 CD bit (empty = not used)" - depends on ETRAX_SERIAL_PORT1 - config ETRAX_SERIAL_PORT2 bool "Serial port 2 enabled" depends on ETRAXFS_SERIAL help Enables the ETRAX FS serial driver for ser2 (ttyS2). -choice - prompt "Ser2 default port type" - depends on ETRAX_SERIAL_PORT2 - default ETRAX_SERIAL_PORT2_TYPE_232 - help - What DMA channel to use for ser2 - -config ETRAX_SERIAL_PORT2_TYPE_232 - bool "Ser2 is a RS-232 port" - help - Configure serial port 2 to be a RS-232 port. - -config ETRAX_SERIAL_PORT2_TYPE_485HD - bool "Ser2 is a half duplex RS-485 port" - depends on ETRAX_RS485 - help - Configure serial port 2 to be a half duplex (two wires) RS-485 port. - -config ETRAX_SERIAL_PORT2_TYPE_485FD - bool "Ser2 is a full duplex RS-485 port" - depends on ETRAX_RS485 - help - Configure serial port 2 to be a full duplex (four wires) RS-485 port. -endchoice - - -config ETRAX_SER2_DTR_BIT - string "Ser 2 DTR bit (empty = not used)" - depends on ETRAX_SERIAL_PORT2 - -config ETRAX_SER2_RI_BIT - string "Ser 2 RI bit (empty = not used)" - depends on ETRAX_SERIAL_PORT2 - -config ETRAX_SER2_DSR_BIT - string "Ser 2 DSR bit (empty = not used)" - depends on ETRAX_SERIAL_PORT2 - -config ETRAX_SER2_CD_BIT - string "Ser 2 CD bit (empty = not used)" - depends on ETRAX_SERIAL_PORT2 - config ETRAX_SERIAL_PORT3 bool "Serial port 3 enabled" depends on ETRAXFS_SERIAL help Enables the ETRAX FS serial driver for ser3 (ttyS3). -choice - prompt "Ser3 default port type" - depends on ETRAX_SERIAL_PORT3 - default ETRAX_SERIAL_PORT3_TYPE_232 - help - What DMA channel to use for ser3. - -config ETRAX_SERIAL_PORT3_TYPE_232 - bool "Ser3 is a RS-232 port" - help - Configure serial port 3 to be a RS-232 port. - -config ETRAX_SERIAL_PORT3_TYPE_485HD - bool "Ser3 is a half duplex RS-485 port" - depends on ETRAX_RS485 - help - Configure serial port 3 to be a half duplex (two wires) RS-485 port. - -config ETRAX_SERIAL_PORT3_TYPE_485FD - bool "Ser3 is a full duplex RS-485 port" - depends on ETRAX_RS485 - help - Configure serial port 3 to be a full duplex (four wires) RS-485 port. -endchoice - -config ETRAX_SER3_DTR_BIT - string "Ser 3 DTR bit (empty = not used)" - depends on ETRAX_SERIAL_PORT3 - -config ETRAX_SER3_RI_BIT - string "Ser 3 RI bit (empty = not used)" - depends on ETRAX_SERIAL_PORT3 - -config ETRAX_SER3_DSR_BIT - string "Ser 3 DSR bit (empty = not used)" - depends on ETRAX_SERIAL_PORT3 - -config ETRAX_SER3_CD_BIT - string "Ser 3 CD bit (empty = not used)" - depends on ETRAX_SERIAL_PORT3 - -config ETRAX_SERIAL_PORT4 - bool "Serial port 4 enabled" - depends on ETRAXFS_SERIAL && CRIS_MACH_ARTPEC3 - help - Enables the ETRAX FS serial driver for ser4 (ttyS4). - -choice - prompt "Ser4 default port type" - depends on ETRAX_SERIAL_PORT4 - default ETRAX_SERIAL_PORT4_TYPE_232 - help - What DMA channel to use for ser4. - -config ETRAX_SERIAL_PORT4_TYPE_232 - bool "Ser4 is a RS-232 port" - help - Configure serial port 4 to be a RS-232 port. - -config ETRAX_SERIAL_PORT4_TYPE_485HD - bool "Ser4 is a half duplex RS-485 port" - depends on ETRAX_RS485 - help - Configure serial port 4 to be a half duplex (two wires) RS-485 port. - -config ETRAX_SERIAL_PORT4_TYPE_485FD - bool "Ser4 is a full duplex RS-485 port" - depends on ETRAX_RS485 - help - Configure serial port 4 to be a full duplex (four wires) RS-485 port. -endchoice - -choice - prompt "Ser4 DMA in channel " - depends on ETRAX_SERIAL_PORT4 - default ETRAX_SERIAL_PORT4_NO_DMA_IN - help - What DMA channel to use for ser4. - - -config ETRAX_SERIAL_PORT4_NO_DMA_IN - bool "Ser4 uses no DMA for input" - help - Do not use DMA for ser4 input. - -config ETRAX_SERIAL_PORT4_DMA9_IN - bool "Ser4 uses DMA9 for input" - depends on ETRAX_SERIAL_PORT4 - help - Enables the DMA9 input channel for ser4 (ttyS4). - If you do not enable DMA, an interrupt for each character will be - used when receiving data. - Normally you want to use DMA, unless you use the DMA channel for - something else. - -endchoice - -config ETRAX_SER4_DTR_BIT - string "Ser 4 DTR bit (empty = not used)" - depends on ETRAX_SERIAL_PORT4 - -config ETRAX_SER4_RI_BIT - string "Ser 4 RI bit (empty = not used)" - depends on ETRAX_SERIAL_PORT4 - -config ETRAX_SER4_DSR_BIT - string "Ser 4 DSR bit (empty = not used)" - depends on ETRAX_SERIAL_PORT4 - -config ETRAX_SER4_CD_BIT - string "Ser 4 CD bit (empty = not used)" - depends on ETRAX_SERIAL_PORT4 - config ETRAX_SYNCHRONOUS_SERIAL bool "Synchronous serial-port support" depends on ETRAX_ARCH_V32 @@ -703,32 +408,6 @@ config ETRAX_SPI_SSER0 want to build it as a module, which will be named spi_crisv32_sser. (You need to select MMC separately.) -config ETRAX_SPI_SSER0_DMA - bool "DMA for SPI on sser0 enabled" - depends on ETRAX_SPI_SSER0 - depends on !ETRAX_SERIAL_PORT1_DMA4_OUT && !ETRAX_SERIAL_PORT1_DMA5_IN - default y - help - Say Y if using DMA (dma4/dma5) for SPI on synchronous serial port 0. - -config ETRAX_SPI_MMC_CD_SSER0_PIN - string "MMC/SD card detect pin for SPI on sser0" - depends on ETRAX_SPI_SSER0 && MMC_SPI - default "pd11" - help - The pin to use for SD/MMC card detect. This pin should be pulled up - and grounded when a card is present. If defined as " " (space), no - pin is selected. A card must then always be inserted for proper - action. - -config ETRAX_SPI_MMC_WP_SSER0_PIN - string "MMC/SD card write-protect pin for SPI on sser0" - depends on ETRAX_SPI_SSER0 && MMC_SPI - default "pd10" - help - The pin to use for the SD/MMC write-protect signal for a memory - card. If defined as " " (space), the card is considered writable. - config ETRAX_SPI_SSER1 tristate "SPI using synchronous serial port 1 (sser1)" depends on ETRAX_SPI_MMC @@ -742,32 +421,6 @@ config ETRAX_SPI_SSER1 want to build it as a module, which will be named spi_crisv32_sser. (You need to select MMC separately.) -config ETRAX_SPI_SSER1_DMA - bool "DMA for SPI on sser1 enabled" - depends on ETRAX_SPI_SSER1 && !ETRAX_ETHERNET_IFACE1 - depends on !ETRAX_SERIAL_PORT0_DMA6_OUT && !ETRAX_SERIAL_PORT0_DMA7_IN - default y - help - Say Y if using DMA (dma6/dma7) for SPI on synchronous serial port 1. - -config ETRAX_SPI_MMC_CD_SSER1_PIN - string "MMC/SD card detect pin for SPI on sser1" - depends on ETRAX_SPI_SSER1 && MMC_SPI - default "pd12" - help - The pin to use for SD/MMC card detect. This pin should be pulled up - and grounded when a card is present. If defined as " " (space), no - pin is selected. A card must then always be inserted for proper - action. - -config ETRAX_SPI_MMC_WP_SSER1_PIN - string "MMC/SD card write-protect pin for SPI on sser1" - depends on ETRAX_SPI_SSER1 && MMC_SPI - default "pd9" - help - The pin to use for the SD/MMC write-protect signal for a memory - card. If defined as " " (space), the card is considered writable. - config ETRAX_SPI_GPIO tristate "Bitbanged SPI using gpio pins" depends on ETRAX_SPI_MMC @@ -782,51 +435,4 @@ config ETRAX_SPI_GPIO Say m to build it as a module, which will be called spi_crisv32_gpio. (You need to select MMC separately.) -# The default match that of sser0, only because that's how it was tested. -config ETRAX_SPI_CS_PIN - string "SPI chip select pin" - depends on ETRAX_SPI_GPIO - default "pc3" - help - The pin to use for SPI chip select. - -config ETRAX_SPI_CLK_PIN - string "SPI clock pin" - depends on ETRAX_SPI_GPIO - default "pc1" - help - The pin to use for the SPI clock. - -config ETRAX_SPI_DATAIN_PIN - string "SPI MISO (data in) pin" - depends on ETRAX_SPI_GPIO - default "pc16" - help - The pin to use for SPI data in from the device. - -config ETRAX_SPI_DATAOUT_PIN - string "SPI MOSI (data out) pin" - depends on ETRAX_SPI_GPIO - default "pc0" - help - The pin to use for SPI data out to the device. - -config ETRAX_SPI_MMC_CD_GPIO_PIN - string "MMC/SD card detect pin for SPI using gpio (space for none)" - depends on ETRAX_SPI_GPIO && MMC_SPI - default "pd11" - help - The pin to use for SD/MMC card detect. This pin should be pulled up - and grounded when a card is present. If defined as " " (space), no - pin is selected. A card must then always be inserted for proper - action. - -config ETRAX_SPI_MMC_WP_GPIO_PIN - string "MMC/SD card write-protect pin for SPI using gpio (space for none)" - depends on ETRAX_SPI_GPIO && MMC_SPI - default "pd10" - help - The pin to use for the SD/MMC write-protect signal for a memory - card. If defined as " " (space), the card is considered writable. - endif diff --git a/arch/cris/arch-v32/mach-a3/Kconfig b/arch/cris/arch-v32/mach-a3/Kconfig index 7796aafc711e..87547271a595 100644 --- a/arch/cris/arch-v32/mach-a3/Kconfig +++ b/arch/cris/arch-v32/mach-a3/Kconfig @@ -15,10 +15,6 @@ config ETRAX_SERIAL_PORTS int default 5 -config ETRAX_DDR - bool - default y - config ETRAX_DDR2_MRS hex "DDR2 MRS" default "0" |